scholarly journals Effect of Particle Size on Microstructure and Element Diffusion at the Interface of Tungsten Carbide/High Strength Steel Composites

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4164 ◽  
Author(s):  
Hongmei Zhang ◽  
Hongnan Li ◽  
Ling Yan ◽  
Chao Wang ◽  
Fangfang Ai ◽  
...  
Keyword(s):  
Particle Size ◽  
Tungsten Carbide ◽  
High Strength Steel ◽  
Average Particle Size ◽  
High Strength ◽  
Average Particle ◽  
Micro Hardness ◽  
Vacuum Sintering ◽  
Element Diffusion ◽  
Average Grain Size

The microstructure and micro-hardness of tungsten carbide/high strength steel (WC/HSS) composites with different particle sizes were analyzed by optical microscopy (OM), scanning electron microscopy (SEM), ultra-high temperature laser confocal microscopy (UTLCM) and micro-hardness testing. The composites were prepared by cold pressing and vacuum sintering. The results show that WC density tends to increase as the average grain size of WC decreases and the micro-hardness of WC increases with the decrease of WC particle size. The micro-hardness of WC near the bonding interface is higher than that in other regions. When the particle size of WC powder particles is 200 nm, a transition layer with a certain width is formed at the interface between WC and HSS, and the combination between the two materials is metallurgical. The iron element in the HSS matrix diffuses into the WC structure in contact with it, resulting in a fusion layer of a certain width, and the composite interface is relatively well bonded. When the average particle size of WC powder is 200 nm, W, Fe and Co elements significantly diffuse in the transition zone at the interface. With the increase of WC particle size, the trend of element diffusion decreases.

Fabrication of silicon carbide nanoceramics

1996 ◽  
Vol 11 (7) ◽  
pp. 1601-1604 ◽  
Author(s):  
Mamoru Mitomo ◽  
Young-Wook Kim ◽  
Hideki Hirotsuru
Keyword(s):  
Silicon Carbide ◽  
Particle Size ◽  
Deformation Behavior ◽  
Superplastic Deformation ◽  
Average Particle Size ◽  
Liquid Phase Sintering ◽  
Carbide Powder ◽  
Average Particle ◽  
Average Grain Size ◽  
Silicon Carbide Powder

Ultrafine silicon carbide powder with an average particle size of 90 nm was densified by hot-processing with the addition of Al2O3, Y2O3, and CaO at 1750 °C. Silicon carbide nanoceramics with an average grain size of 110 nm were prepared by liquid phase sintering at low temperature. The materials showed superplastic deformation at a strain rate of 5.0 × 10-4/s at 1700 °C, which is the lowest temperature published. The microstructure and deformation behavior of materials from a submicrometer powder were also investigated as a reference.

scholarly journals Study on the Shear Band of Sand with Various Particle Characteristics Using PIV Analysis

2019 ◽  
Vol 92 ◽  
pp. 06005
Author(s):  
Shintaro Kajiyama ◽  
Yukio Nakata ◽  
Ryota Miyamoto ◽  
Masato Taue
Keyword(s):  
Particle Size ◽  
Shear Band ◽  
Inclination Angle ◽  
Average Particle Size ◽  
Average Particle ◽  
Sample Standard Deviation ◽  
Particle Characteristics ◽  
Coral Sand ◽  
Average Grain Size ◽  
Toyoura Sand

The phenomenon of ground undergoing large plastic deformation, leading to collapse, occurs due to the localization of unstable deformation. The investigation of shear band is important in order to understand the destructive phenomenon. Therefore, a series of experiments were conducted on sands with different particle characteristics so that behaviour of the shear band of sand under plane strain compression could be investigated. Specifically, Toyoura sand and two kinds of coral sand, hereafter referred to as coral sand A (with smaller average particle size) and coral sand B (with larger average particle size) were used. The shear band was evaluated using PIV (Partial Image Velocimetry) analysis. As a result, it became clear that the relationship between shear inclination angle and internal friction angle does not hold for the two kinds of coral sand because the shear inclination angle is low. The ratio of the average value of the shear band width to the average grain size at the peak was 10 to 20 times, 7 to 10 times, and 5 to 8 times in the order of Toyoura sand, coral sand A, and coral sand B. The sample standard deviation was 0.1 to 0.9 mm, 0.9 to 1.6 mm, and 1.4 to 1.9 mm.

Study on the Microstructure and Properties of ZL205A Alloy under Partial Remelting Treatment

2012 ◽  
Vol 538-541 ◽  
pp. 1183-1186
Author(s):  
Min Li ◽  
Lan Rong Cai ◽  
Peng Xin Liu
Keyword(s):  
Particle Size ◽  
Grain Size ◽  
Tensile Strength ◽  
Average Particle Size ◽  
Average Particle ◽  
High Tensile Strength ◽  
Microstructure And Properties ◽  
Partial Remelting ◽  
Average Grain Size ◽  
Zl205a Alloy

In this paper, effects of partial remelting treatment on microstructure and properties of ZL205A alloy were studied in detail. The results show that the grain size of ZL205A alloy decreases at different degree. The grain size increases first and then decreases with increasing of returns content. The average grain size of the primary ZL205A alloy was measured to be about 60 μm, and the good result can be got of the ZL205A alloys with the average particle size of α (Al) phase being about 33 μm after adding 20wt.% returns. The ZL205A alloy with 20 wt.% returns has a considerably high tensile strength and yield strength of 525MPa and 445 MPa, respectively, which is much higher than 501 MPa and 421 MPa of primary ZL205A alloy, meanwhile the elongation level is up to14%.

scholarly journals Research on the Influence of the Manufacturing Process Conditions of Iron Sintered with the Addition of Layered Lubricating Materials on its Selected Properties

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4782
Author(s):  
Wieslaw Urbaniak ◽  
Tomasz Majewski ◽  
Ryszard Wozniak ◽  
Judyta Sienkiewicz ◽  
Jozef Kubik ◽  
...  
Keyword(s):  
Particle Size ◽  
Boron Nitride ◽  
Coefficient Of Friction ◽  
Tribological Properties ◽  
Hexagonal Boron Nitride ◽  
Average Particle Size ◽  
Layered Materials ◽  
Process Conditions ◽  
Average Particle ◽  
Average Grain Size

The purpose of the conducted experiments was to test the selected properties of materials intended for porous sintered bearings containing layered materials in the form of powders with an average particle size of 0.5–1.5 μm, with very good tribological properties. The subject of the research was a sinter based on iron powder with the addition of layered materials; molybdenum disulfide MoS2 (average particle size 1.5 μm), tungsten disulfide WS2 (average particle size 0.6 μm), hexagonal boron nitride, h-BN (average particle size 0.5 and 1.5 μm) with two different porosities. The article presents the results of density and porosity tests, compressive strength, metallographic and tribological tests and the assessment of changes in the surface condition occurring during the long storage period. The use of layered additives allows for an approximately 20% lower coefficient of friction. In the case of sulfides, the technological process of pressing 250 MPa, 350 MPa, and sintering at a temperature of 1120 °C allows us to obtain a material with good strength and tribological properties, better than in the case of h-BN. However, the main problem is the appearance of elements from the decomposition of sulfide compounds in the material matrix, which results in rapid material degradation. In hexagonal boron nitride, such disintegration under these conditions does not occur; the material as observed does not degrade. In this case, the material is characterized by lower hardness, resulting from a different behavior of hexagonal boron nitride in the pressing and sintering process; in this case, pressing at a pressure of 350 MPa seems to be too low. However, taking into account that even with these technological parameters, the obtained material containing 2.5% h-BN with an average grain size of 1.5 μm allowed obtaining a coefficient of friction at the level of 0.41, which, with very good material durability, seems to be very positive news before further tests.

scholarly journals Studying the Crystal Structure, Topography, and Anti-bacterial of a Novel Titania (TiO2 NPs) Prepared by a Sol-gel Manner

2019 ◽  
Vol 16 (4) ◽  
pp. 0910
Author(s):  
Fayyadh Et al.
Keyword(s):  
Particle Size ◽  
Antibacterial Activity ◽  
Titanium Dioxide ◽  
Calcination Temperature ◽  
Sol Gel ◽  
Average Particle Size ◽  
Average Particle ◽  
Gram Negative ◽  
Tio2 Nps ◽  
Average Grain Size

In this research, titanium dioxide nanoparticles (TiO2 NPs) were prepared through the sol-gel process at an acidic medium (pH3).TiO2 nanoparticles were prepared from titanium trichloride (TiCl3) as a precursor with Ammonium hydroxide (NH4OH) with 1:3 ratio at 50 °C. The resulting gel was dried at 70 °C to obtain the Nanocrystalline powder. The powder from the drying process was treated thermally at temperatures 500 °C and 700 °C. The crystalline structure, surface morphology, and particle size were studied by using X-ray diffraction (XRD), Atomic Force Microscopy (AFM), and Scanning Electron Microscope (SEM). The results showed (anatase) phase of titanium dioxide with the average grain size of 110 nm at 500 °C calcination temperature, and (anatase- rutile) mixed phase of titanium dioxide with the average particle size of 118.1 nm at 700 °C calcination temperature. The anti-bacterial activity of the synthesis specimens was recorded through the Kirby-Bauer disc method (disc devotion method). The results displayed a pretty excellent antibacterial activity of TiO2 NPs to bacteria strains: Gram positive staphylococcus aureus, gram negative pseudomonas aeruginosa, and "gram negative escherichia coli. The sensitivity of the tested bacteria to TiO2 NPs depends on the oxidation state of the TiO2 NPs, particle size, volume, and the density of the unit cell. The small- average particle size of titanium dioxide particles showed high antibacterial activity against bacteria, while the larger- average particle size of titanium dioxide particles showed less antibacterial activity. The novelty of this production is the manufacturing of a novel kind of TiO2 NPs and achievement its best antibacterial activity.

Determination of grinding parameters of fenugreek seed

1970 ◽  
Vol 26 (1) ◽  
pp. 16 ◽  
Author(s):  
S Balasubramanian ◽  
Rajkumar Rajkumar ◽  
K K Singh
Keyword(s):  
Particle Size ◽  
Energy Consumption ◽  
Moisture Content ◽  
Specific Energy ◽  
Feed Rate ◽  
Average Particle Size ◽  
Specific Energy Consumption ◽  
Average Particle ◽  
Fenugreek Seeds ◽  
Fenugreek Seed

Experiment to identify ambient grinding conditions and energy consumed was conducted for fenugreek. Fenugreek seeds at three moisture content (5.1%, 11.5% and 17.3%, d.b.) were ground using a micro pulverizer hammer mill with different grinding screen openings (0.5, 1.0 and 1.5 mm) and feed rate (8, 16 and 24 kg h-1) at 3000 rpm. Physical properties of fenugreek seeds were also determined. Specific energy consumptions were found to decrease from 204.67 to 23.09 kJ kg-1 for increasing levels of feed rate and grinder screen openings. On the other hand specific energy consumption increased with increasing moisture content. The highest specific energy consumption was recorded for 17.3% moisture content and 8 kg h-1 feed rate with 0.5 mm screen opening. Average particle size decreased from 1.06 to 0.39 mm with increase of moisture content and grinder screen opening. It has been observed that the average particle size was minimum at 0.5 mm screen opening and 8 kg h-1 feed rate at lower moisture content. Bond’s work index and Kick’s constant were found to increase from 8.97 to 950.92 kWh kg-1 and 0.932 to 78.851 kWh kg-1 with the increase of moisture content, feed rate and grinder screen opening, respectively. Size reduction ratio and grinding effectiveness of fenugreek seed were found to decrease from 4.11 to 1.61 and 0.0118 to 0.0018 with the increase of moisture content, feed rate and grinder screen opening, respectively. The loose and compact bulk densities varied from 219.2 to 719.4 kg m-3 and 137.3 to 736.2 kg m-3, respectively.  

Formulating SLN and NLC as Innovative Drug Delivery Systems for Non-Invasive Routes of Drug Administration

2020 ◽  
Vol 27 (22) ◽  
pp. 3623-3656 ◽  
Author(s):  
Bruno Fonseca-Santos ◽  
Patrícia Bento Silva ◽  
Roberta Balansin Rigon ◽  
Mariana Rillo Sato ◽  
Marlus Chorilli
Keyword(s):  
Drug Delivery ◽  
Particle Size ◽  
Drug Release ◽  
Drug Loading ◽  
Average Particle Size ◽  
Delivery Systems ◽  
Average Particle ◽  
Minor Importance ◽  
Routes Of Administration ◽  
Non Invasive

Colloidal carriers diverge depending on their composition, ability to incorporate drugs and applicability, but the common feature is the small average particle size. Among the carriers with the potential nanostructured drug delivery application there are SLN and NLC. These nanostructured systems consist of complex lipids and highly purified mixtures of glycerides having varying particle size. Also, these systems have shown physical stability, protection capacity of unstable drugs, release control ability, excellent tolerability, possibility of vectorization, and no reported production problems related to large-scale. Several production procedures can be applied to achieve high association efficiency between the bioactive and the carrier, depending on the physicochemical properties of both, as well as on the production procedure applied. The whole set of unique advantages such as enhanced drug loading capacity, prevention of drug expulsion, leads to more flexibility for modulation of drug release and makes Lipid-based nanocarriers (LNCs) versatile delivery system for various routes of administration. The route of administration has a significant impact on the therapeutic outcome of a drug. Thus, the non-invasive routes, which were of minor importance as parts of drug delivery in the past, have assumed added importance drugs, proteins, peptides and biopharmaceuticals drug delivery and these include nasal, buccal, vaginal and transdermal routes. The objective of this paper is to present the state of the art concerning the application of the lipid nanocarriers designated for non-invasive routes of administration. In this manner, this review presents an innovative technological platform to develop nanostructured delivery systems with great versatility of application in non-invasive routes of administration and targeting drug release.

Azithromycin nanosuspension preparation using evaporative precipitation into aqueous solution (EPAS) method and its comparative dissolution study

2020 ◽  
Vol 17 ◽  
Author(s):  
Mohammad Hossain Shariare ◽  
Tonmoy Kumar Mondal ◽  
Hani Alothaid ◽  
Md. Didaruzzaman Sohel ◽  
MD Wadud ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Dissolution Rate ◽  
Average Particle Size ◽  
Scale Up ◽  
Average Particle ◽  
Total Drug ◽  
Residual Solvent ◽  
Dissolution Study ◽  
Drug Content

Aim: EPAS (evaporative precipitation into aqueous solution) was used in the current studies to prepare azithromycin nanosuspensions and investigate the physicochemical characteristics for the nanosuspension batches with the aim of enhancing the dissolution rate of the nanopreparation to improve bioavailability. Methods: EPAS method used in this study for preparing azithromycin nanosuspension was achieved through developing an in-house instrumentation method. Particle size distribution was measured using Zetasizer Nano S without sample dilution. Dissolved azithromycin nanosuspensions were also compared with raw azithromycin powder and commercially available products. Total drug content of nanosuspension batches were measured using an Ultra-Performance Liquid Chromatography (UPLC) system with Photodiode Array (PDA) detector while residual solvent was measured using gas chromatography (GC). Results: The average particle size of azithromycin nanosuspension was 447.2 nm and total drug content was measured to be 97.81% upon recovery. Dissolution study data showed significant increase in dissolution rate for nanosuspension batch when compared to raw azithromycin and commercial version (microsuspension). The residual solvent found for azithromycin nanosuspension is 0.000098023 mg/ mL or 98.023 ppb. Conclusion: EPAS was successfully used to prepare azithromycin nanoparticles that exhibited significantly enhanced dissolution rate. Further studies are required to scale up the process and determine long term stability of the nanoparticles.

scholarly journals Evaluation of the Effects of Filler Fineness on the Properties of an Epoxy Asphalt Mixture

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2003
Author(s):  
Wei Xu ◽  
Jintao Wei ◽  
Zhengxiong Chen ◽  
Feng Wang ◽  
Jian Zhao
Keyword(s):  
Particle Size ◽  
Average Particle Size ◽  
Asphalt Mixture ◽  
Average Particle ◽  
Fine Dust ◽  
Bonding Structure ◽  
Epoxy Asphalt ◽  
Mineral Powder ◽  
Marshall Stability ◽  
Mixture Sample

The type and fineness of a filler significantly affect the performance of an asphalt mixture. There is a lack of specific research on the effects of filler fineness and dust from aggregates on the properties of epoxy asphalt (EA) mixtures. The effects of aggregate dust and mineral powder on the properties of an EA mixture were evaluated. These filler were tested to determine their fineness, specific surface area and mineral composition. The effects of these fillers on the EA mastic sample and mixture were evaluated. The morphology of the EA mastic samples was analyzed using scanning electron microscopy (SEM). The effects of the fillers on the Marshall stability, tensile strength and fatigue performance of the EA mixture were evaluated. The dust from the aggregates exhibited an even particle size distribution, and its average particle size was approximately 20% of that of the mineral powder. The SEM microanalysis showed that the EA mastic sample containing relatively fine dust formed a tight and dense interfacial bonding structure with the aggregate. The EA mixture sample containing filler composed of dust from aggregate had a significantly higher strength and longer fatigue life than that of the EA sample containing filler composed of mineral powder.

scholarly journals Surface Activity of Humic Acid and Its Sub-Fractions from Forest Soil

2021 ◽  
Vol 13 (15) ◽  
pp. 8122
Author(s):  
Shijie Tian ◽  
Weiqiang Tan ◽  
Xinyuan Wang ◽  
Tingting Li ◽  
Fanhao Song ◽  
...  
Keyword(s):  
Surface Tension ◽  
Particle Size ◽  
Humic Acid ◽  
Forest Soil ◽  
Surface Activity ◽  
Self Assembly ◽  
Average Particle Size ◽  
Gaussian Model ◽  
Exponential Model ◽  
Average Particle

Surface activity of humic acid (HA) and its six sub-fractions isolated from forest soil were characterized by surface tension measurements, dynamic light scattering, and laser doppler electrophoresis. The surface tension of HA and its sub-fractions reduced from 72.4 mN·m−1 to 36.8 mN·m−1 in exponential model with the increasing concentration from 0 to 2000 mg·L−1. The critical micelle concentration (CMC) and Z-average particle size ranged from 216–1024 mg·L−1 and 108.2–186.9 nm for HA and its sub-fractions, respectively. The CMC have related with alkyl C, O-alkyl C, aromatic C, and carbonyl C (p < 0.05), respectively, and could be predicted with the multiple linear regression equation of CMC, CMC = 18896 − 6.9 × C-296 × alkyl C-331 × aromatic C-17019 × H/C + 4054 × HB/HI (p < 0.05). The maximum particle size was 5000 nm after filtered by a membrane with pore size of 450 nm, indicating HA and its sub-fractions could progressed self-assembly at pH 6.86. The aggregate sizes of number-base particle size distributions were mainly in six clusters including 2 ± 1 nm, 5 ± 2 nm, 10 ± 3 nm, 21 ± 8 nm, 40 ± 10 nm, and >50 nm analyzed by Gaussian model that maybe due to the inconsistency of the components and structures of the HA sub-fractions, requiring further study. It is significance to explore the surface activity of HA and its sub-fractions, which is helpful to clarify the environmental behavior of HA.

Sign in / Sign up

Export Citation Format

Share Document