scholarly journals Characteristics, Mechanism and Criterion of Channel Segregation in NbTi Alloy via Numerical Simulations and Experimental Characterizations

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 796
Author(s):  
Baohui Zhu ◽  
Zhenzhen Chen ◽  
Yanfei Cao ◽  
Yanchang Liu ◽  
Xiuhong Kang ◽  
...  
Keyword(s):  
Critical Value ◽  
Engineering Practice ◽  
X Ray ◽  
Transmission Imaging ◽  
Interdendritic Flow ◽  
Channel Segregation ◽  
Channel Initiation ◽  
Solidification Parameters ◽  
Two Stages ◽  
First Time

Channel segregation (CS) is the most typical defect during solidification of NbTi alloy. Based on numerical simulation and experimental characterizations, we deeply elucidated its characteristics, formation mechanism, effecting factor and prediction criterion. According to acid etching, industrial X-ray transmission imaging, 3D X-ray microtomography and chemical analysis, it was found that in a casing ingot, by He cooling, finer grain size, weaker segregation and slighter CS can be obtained compared with air-cooled ingot. The simulation results of macrosegregation show that CS is caused by the strong natural convection in the mushy zone triggered by the thermo-solutal gradient. Its formation can be divided into two stages including channel initiation and growth. In addition, due to the stronger cooling effect of the He treatment, the interdendritic flow velocity becomes smaller, consequently lowering the positive segregation and CS and improving the global homogenization of the final ingot. Finally, to predict the formation of CS, the Rayleigh number model was proposed and its critical value was found to be 15 in NbTi alloy for the first time. When it is lower than the threshold, CS disappears. It provides an effective tool to evaluate and optimize the solidification parameters to fabricate the homogenized NbTi ingot in engineering practice.

Identification of Asbestos Fibres in a Water Sample by X-Ray Microanalysis

1975 ◽  
Vol 33 ◽  
pp. 274-275
Author(s):  
K. A. Brookes ◽  
D. Finbow ◽  
Madeleine Samuel
Keyword(s):  
Water Sample ◽  
Background Radiation ◽  
X Ray ◽  
Left Hand ◽  
Transmission Imaging ◽  
Different Types ◽  
Normal Specimen ◽  
Liquid Nitrogen Cooling ◽  
Normal Transmission ◽  
Additional Port

Investigation of the particulate matter contained in the water sample, revealed the presence of a number of different types and certain of these were selected for analysis.An A.E.I. Corinth electron microscope was modified to accept a Kevex Si (Li) detector. To allow for existing instruments to be readily modified, this was kept to a minimum. An additional port is machined in the specimen region to accept the detector, with the liquid nitrogen cooling dewar conveniently housed in the left hand cupboard adjacent to the microscope column. Since background radiation leads to loss in the sensitivity of the instrument, great care has been taken to reduce this effect by screening and manufacturing components that are near the specimen from material of low atomic number. To change from normal transmission imaging to X-ray analysis, the special 4-position specimen rod is inserted through the normal specimen airlock.

X-ray Gabor holography

1995 ◽  
Vol 53 ◽  
pp. 612-613
Author(s):  
Steve Lindaas ◽  
Chris Jacobsen ◽  
Alex Kalinovsky ◽  
Malcolm Howells
Keyword(s):  
Surface Relief ◽  
Biological Imaging ◽  
Specimen Preparation ◽  
X Rays ◽  
X Ray ◽  
Water Window ◽  
Biological Objects ◽  
Transmission Imaging ◽  
Atomic Force ◽  
Electron Microscopes

Soft x-ray microscopy offers an approach to transmission imaging of wet, micron-thick biological objects at a resolution superior to that of optical microscopes and with less specimen preparation/manipulation than electron microscopes. Gabor holography has unique characteristics which make it particularly well suited for certain investigations: it requires no prefocussing, it is compatible with flash x-ray sources, and it is able to use the whole footprint of multimode sources. Our method serves to refine this technique in anticipation of the development of suitable flash sources (such as x-ray lasers) and to develop cryo capabilities with which to reduce specimen damage. Our primary emphasis has been on biological imaging so we use x-rays in the water window (between the Oxygen-K and Carbon-K absorption edges) with which we record holograms in vacuum or in air.The hologram is recorded on a high resolution recording medium; our work employs the photoresist poly(methylmethacrylate) (PMMA). Following resist “development” (solvent etching), a surface relief pattern is produced which an atomic force microscope is aptly suited to image.

Diphosphinoazine Rhodium(I) and Iridium(I) Complexes

2006 ◽  
Vol 71 (2) ◽  
pp. 197-206 ◽  
Author(s):  
Martin Pošta ◽  
Jan Čermák ◽  
Pavel Vojtíšek ◽  
Ivana Císařová
Keyword(s):  
Rhodium Complexes ◽  
Iridium Complexes ◽  
X Ray ◽  
First Time

The first rhodium complexes of diphosphinoazines [{RhCl(1,2-η:5,6-η-CH=CHCH2CH2CH=CHCH2CH2)}2 {μ-R2PCH2C(But)=NN=C(But)CH2PR2] (R = Ph, Cy, Pri) were prepared by cleavage of the bridge in chloro(cycloocta-1,5-diene)rhodium(I) dimer, the analogous iridium(I) complexes were also prepared for the first time. The X-ray structures of isostructural rhodium and iridium complexes with bis(dicyclohexylphosphino)pinacoloneazine were determined. Diphosphinoazine ligands in the complexes remained in (Z,Z) configuration bridging two RhCl(C8H12) units.

scholarly journals Quartz Crystallite Size and Moganite Content as Indicators of the Mineralogical Maturity of the Carboniferous Chert: The Case of Cherts from Eastern Asturias (Spain)

Minerals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 611
Author(s):  
Celia Marcos ◽  
María de Uribe-Zorita ◽  
Pedro Álvarez-Lloret ◽  
Alaa Adawy ◽  
Patricia Fernández ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Crystallite Size ◽  
Archaeological Sites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Infrared And Raman Spectroscopy ◽  
First Time ◽  
Geological Formations

Chert samples from different coastal and inland outcrops in the Eastern Asturias (Spain) were mineralogically investigated for the first time for archaeological purposes. X-ray diffraction, X-ray fluorescence, transmission electron microscopy, infrared and Raman spectroscopy and total organic carbon techniques were used. The low content of moganite, since its detection by X-ray diffraction is practically imperceptible, and the crystallite size (over 1000 Å) of the quartz in these cherts would be indicative of its maturity and could potentially be used for dating chert-tools recovered from archaeological sites. Also, this information can constitute essential data to differentiate the cherts and compare them with those used in archaeological tools. However, neither composition nor crystallite size would allow distinguishing between coastal and inland chert outcrops belonging to the same geological formations.

scholarly journals First Report on the Geologic Occurrence of Natural Na–A Zeolite and Associated Minerals in Cretaceous Mudstones of the Paja Formation of Vélez (Santander), Colombia

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Carlos Alberto Ríos-Reyes ◽  
German Alfonso Reyes-Mendoza ◽  
José Antonio Henao-Martínez ◽  
Craig Williams ◽  
Alan Dyer
Keyword(s):  
Natural Zeolite ◽  
Scanning Electron Micrographs ◽  
Total Sulfur ◽  
Zeolite A ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mineral Phases ◽  
The World ◽  
Porosity And Permeability ◽  
First Time

This study reports for the first time the geologic occurrence of natural zeolite A and associated minerals in mudstones from the Cretaceous Paja Formation in the urban area of the municipality of Vélez (Santander), Colombia. These rocks are mainly composed of quartz, muscovite, pyrophyllite, kaolinite and chlorite group minerals, framboidal and cubic pyrite, as well as marcasite, with minor feldspar, sulphates, and phosphates. Total organic carbon (TOC), total sulfur (TS), and millimeter fragments of algae are high, whereas few centimeters and not biodiverse small ammonite fossils, and other allochemical components are subordinated. Na–A zeolite and associated mineral phases as sodalite occur just beside the interparticle micropores (honeycomb from framboidal, cube molds, and amorphous cavities). It is facilitated by petrophysical properties alterations, due to processes of high diagenesis, temperatures up to 80–100 °C, with weathering contributions, which increase the porosity and permeability, as well as the transmissivity (fluid flow), allowing the geochemistry remobilization and/or recrystallization of pre-existing silica, muscovite, kaolinite minerals group, salts, carbonates, oxides and peroxides. X-ray diffraction analyses reveal the mineral composition of the mudstones and scanning electron micrographs show the typical cubic morphology of Na–A zeolite of approximately 0.45 mμ in particle size. Our data show that the sequence of the transformation of phases is: Poorly crystalline aluminosilicate → sodalite → Na–A zeolite. A literature review shows that this is an unusual example of the occurrence of natural zeolites in sedimentary marine rocks recognized around the world.

scholarly journals The Effect of Surfactant-Modified Montmorillonite on the Cross-Linking Efficiency of Polysiloxanes

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2623
Author(s):  
Monika Wójcik-Bania ◽  
Jakub Matusik
Keyword(s):  
Total Pore Volume ◽  
Cross Linking ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
The Cross ◽  
Chain Lengths ◽  
First Time ◽  
Substituent Influence ◽  
Benzyl Substituent

Polymer–clay mineral composites are an important class of materials with various applications in the industry. Despite interesting properties of polysiloxanes, such matrices were rarely used in combination with clay minerals. Thus, for the first time, a systematic study was designed to investigate the cross-linking efficiency of polysiloxane networks in the presence of 2 wt % of organo-montmorillonite. Montmorillonite (Mt) was intercalated with six quaternary ammonium salts of the cation structure [(CH3)2R’NR]+, where R = C12, C14, C16, and R’ = methyl or benzyl substituent. The intercalation efficiency was examined by X-ray diffraction, CHN elemental analysis, and Fourier transform infrared (FTIR) spectroscopy. Textural studies have shown that the application of freezing in liquid nitrogen and freeze-drying after the intercalation increases the specific surface area and the total pore volume of organo-Mt. The polymer matrix was a poly(methylhydrosiloxane) cross-linked with two linear vinylsiloxanes of different siloxane chain lengths between end functional groups. X-ray diffraction and transmission electron microscopy studies have shown that the increase in d-spacing of organo-Mt and the benzyl substituent influence the degree of nanofillers’ exfoliation in the nanocomposites. The increase in the degree of organo-Mt exfoliation reduces the efficiency of hydrosilylation reaction monitored by FTIR. This was due to physical hindrance induced by exfoliated Mt particles.

scholarly journals Homopiperazine (Hexahydro-1,4-diazepine)

Molbank ◽  
10.3390/m1200 ◽  
2021 ◽  
Vol 2021 (2) ◽  
pp. M1200
Author(s):  
R. Alan Aitken ◽  
Dheirya K. Sonecha ◽  
Alexandra M. Z. Slawin
Keyword(s):  
13C Nmr ◽  
Title Compound ◽  
Coupling Constants ◽  
15N Nmr ◽  
Time Data ◽  
Nmr Spectrum ◽  
X Ray ◽  
First Time

The X-ray structure of the title compound has been determined for the first time. Data on its 1H–13C-NMR coupling constants and 15N-NMR spectrum are also given.

scholarly journals A novel and potentially scalable CVD-based route towards SnO2:Mo thin films as transparent conducting oxides

2021 ◽  
Author(s):  
Tianlei Ma ◽  
Marek Nikiel ◽  
Andrew G. Thomas ◽  
Mohamed Missous ◽  
David J. Lewis
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Mixed Valence ◽  
Chemical Vapour ◽  
X Ray Diffraction ◽  
X Ray ◽  
Conducting Oxides ◽  
Valence States ◽  
3 Omega ◽  
First Time

AbstractIn this report, we prepared transparent and conducting undoped and molybdenum-doped tin oxide (Mo–SnO2) thin films by aerosol-assisted chemical vapour deposition (AACVD). The relationship between the precursor concentration in the feed and in the resulting films was studied by energy-dispersive X-ray spectroscopy, suggesting that the efficiency of doping is quantitative and that this method could potentially impart exquisite control over dopant levels. All SnO2 films were in tetragonal structure as confirmed by powder X-ray diffraction measurements. X-ray photoelectron spectroscopy characterisation indicated for the first time that Mo ions were in mixed valence states of Mo(VI) and Mo(V) on the surface. Incorporation of Mo6+ resulted in the lowest resistivity of $$7.3 \times 10^{{ - 3}} \Omega \,{\text{cm}}$$ 7.3 × 10 - 3 Ω cm , compared to pure SnO2 films with resistivities of $$4.3\left( 0 \right) \times 10^{{ - 2}} \Omega \,{\text{cm}}$$ 4.3 0 × 10 - 2 Ω cm . Meanwhile, a high transmittance of 83% in the visible light range was also acquired. This work presents a comprehensive investigation into impact of Mo doping on SnO2 films synthesised by AACVD for the first time and establishes the potential for scalable deposition of SnO2:Mo thin films in TCO manufacturing. Graphical abstract

scholarly journals Reactive Dual Magnetron Sputtering: A Fast Method for Preparing Stoichiometric Microcrystalline ZnWO4 Thin Films

Surfaces ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 106-114
Author(s):  
Yannick Hermans ◽  
Faraz Mehmood ◽  
Kerstin Lakus-Wollny ◽  
Jan P. Hofmann ◽  
Thomas Mayer ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Fast Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates ◽  
Post Annealing ◽  
Rf Signal ◽  
First Time

Thin films of ZnWO4, a promising photocatalytic and scintillator material, were deposited for the first time using a reactive dual magnetron sputtering procedure. A ZnO target was operated using an RF signal, and a W target was operated using a DC signal. The power on the ZnO target was changed so that it would match the sputtering rate of the W target operated at 25 W. The effects of the process parameters were characterized using optical spectroscopy, X-ray diffraction, and scanning electron microscopy, including energy dispersive X-ray spectroscopy as well as X-ray photoelectron spectroscopy. It was found that stoichiometric microcrystalline ZnWO4 thin films could be obtained, by operating the ZnO target during the sputtering procedure at a power of 55 W and by post-annealing the resulting thin films for at least 10 h at 600 °C. As FTO coated glass substrates were used, annealing led as well to the incorporation of Na, resulting in n+ doped ZnWO4 thin films.

scholarly journals Revealing noncollinear magnetic ordering at the atomic scale via XMCD

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Fridtjof Kielgast ◽  
Ivan Baev ◽  
Torben Beeck ◽  
Federico Pressacco ◽  
Michael Martins
Keyword(s):  
Ground State ◽  
Magnetic Circular Dichroism ◽  
Magnetic Moments ◽  
Magnetic Ordering ◽  
Atomic Scale ◽  
Angle Of Incidence ◽  
X Ray ◽  
First Time ◽  
X Ray Absorption ◽  
Magnetic Sublattices

AbstractMass-selected V and Fe monomers, as well as the heterodimer $${\text{Fe}}_1{\text{V}}_1$$ Fe 1 V 1 , were deposited on a Cu(001) surface. Their electronic and magnetic properties were investigated via X-ray absorption (XAS) and X-ray magnetic circular dichroism (XMCD) spectroscopy. Anisotropies in the magnetic moments of the deposited species could be examined by means of angle resolving XMCD, i.e. changing the X-ray angle of incidence. A weak adatom-substrate-coupling was found for both elements and, using group theoretical arguments, the ground state symmetries of the adatoms were determined. For the dimer, a switching from antiparallel to parallel orientation of the respective magnetic moments was observed. We show that this is due to the existence of a noncollinear spin-flop phase in the deposited dimers, which could be observed for the first time in such a small system. Making use of the two magnetic sublattices model, we were able to find the relative orientations for the dimer magnetic moments for different incidence angles.

Sign in / Sign up

Export Citation Format

Share Document