scholarly journals Study on Mechanical Characteristics and Failure Modes of Coal–Mudstone Combined Body with Prefabricated Crack

Mathematics ◽  
2022 ◽  
Vol 10 (2) ◽  
pp. 177
Author(s):  
Huayong Lv ◽  
Defeng Wang ◽  
Zhanbo Cheng ◽  
Yaning Zhang ◽  
Tao Zhou
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Acoustic Emissions ◽  
Body Part ◽  
Unconfined Compression Test ◽  
Crack Angle ◽  
Continuous Loading

There are normally pre-existing cracks that can be observed in the coal seam and immediate roof that influences the stability of the rib spalling and the movement law of overlying strata. In this study, comprehensive research methods (e.g., theory analysis, experimental tests and numerical simulations) were adopted to reveal the mechanical characteristics, acoustic emission behaviors and failure modes of a coal–mudstone combined body with a single prefabricated non-penetrating crack. The results show that the influence of the crack angle on the elastic modulus of the coal–mudstone combined body samples was limited. With the increase in the crack angle, the unconfined compressive strength of samples decreased first and then increased in a V-shaped trend. In addition, the minimum unconfined compressive strength could be observed at a crack angle of 45°. Moreover, the number of acoustic emissions significantly increased with the process of continuous loading. In addition, the stress reduction zone could be observed in both ends of the prefabricated cracks at the initial stage of loading. The high- and low-stress zones were transformed with the process of continuous loading. Under an unconfined compression test, the failure models of the coal body part in the samples were mainly caused by shear failure, and only a few cracks occurred in the upper tip of the prefabricated cracks of the mudstone part. Therefore, airfoil cracks could be observed in the samples due to the strength difference of the coal mass and mudstone.

scholarly journals Effect of Filling Interval Time on Long-Term Mechanical Strength of Layered Cemented Tailing Backfill

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Shuai Cao ◽  
Wei-dong Song
Keyword(s):  
Compressive Strength ◽  
Mechanical Strength ◽  
Failure Modes ◽  
Shear Failure ◽  
Development Stage ◽  
Stability Control ◽  
Tensile Failure ◽  
Uniaxial Compression Test ◽  
Linear Elastic ◽  
Shear Mixing

To explore the influence that filling interval has on the mechanical strength of layered cemented tailing backfill (LCTB), uniaxial compression test is conducted on LCTB samples with a concentration of 70%, 72%, and 75% and a filling interval of 12 h, 24 h, 36 h, and 48 h. From the tests above, mechanical properties and failure modes of LCTB are acquired. The results are as follows: (1) The peak compressive strength of LCTB decreases as the filling interval increases, and it increases when the concentration grows with a certain length of filling interval. At the same time, the peak compressive strength and filling interval show polynomial distribution. (2) There are four stages during the loading process of cemented backfill specimen, that is, compression stage, linear elastic stage, crack extension stage, and undermines development stage. As the filling interval increases, CTB shows a failure mode of tensile failure-tensile shear failure transition-tensile and shear mixing destruction, which provides a theoretical basis for strength design and stability control of backfill.

scholarly journals Experimental Study of the Mechanical Characteristics of a Rock-Like Material Containing a Preexisting Fissure under Loading and Unloading Triaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-12 ◽  
Author(s):  
Taoli Xiao ◽  
Mei Huang ◽  
Min Gao
Keyword(s):  
Experimental Study ◽  
Failure Mode ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Tensile Failure ◽  
Underground Engineering ◽  
Inclination Angles ◽  
Loading And Unloading

An experimental study of a rock-like material containing a preexisting fissure subjected to loading and unloading triaxial compression is carried out, and the results show that the mechanical characteristics of the rock-like specimen depend heavily on the loading paths and the inclination of the fissure. The triaxial loading experiment results show that the failure strength linearly increases, while the residual strength linearly decreases with increasing inclination. Furthermore, specimens subjected to triaxial compression show an “X”-type shear failure mode. The triaxial unloading compression experimental results show that specimens with different inclination angles have various failure modes. Specimens with gentle inclinations show a tensile-shear mix failure mode, specimens with middle inclinations show a shear-sliding failure mode, and specimens with steep inclinations show a tensile failure mode. These findings can be used to forecast excavation-induced instabilities in deep underground engineering rock structures.

scholarly journals Investigation of the anisotropic confinement-dependent brittleness of a Utah coal

2020 ◽  
Author(s):  
Bo-Hyun Kim ◽  
Gabriel Walton ◽  
Mark K. Larson ◽  
Steve Berry
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Shear Failure ◽  
Confining Stress ◽  
Included Angle ◽  
Anisotropic Strength ◽  
Brittle Ductile Transition ◽  
The Given ◽  
Compressive Tests

Abstract Changes of failure mechanism with increasing confinement, from extensional to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In an analysis published in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of 84 specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction, defined as the included angle. A total of four different included angles were used in the work performed in 2018. The authors found that the degree of anisotropic strength differed according to the included angle. However, the transition from extensional to shear failure at the given confinements was not clearly identified. In this study, a total of 20 specimens were additionally prepared from the same coal sample used in the previous study and then tested under both unconfined and triaxial compressive conditions. Because the authors already knew the most contrasting cases of the included angles from the previous work using the four included angles, they chose only two of the included angles (0° and 30°) for this study. For the triaxial compressive tests, a greater confining stress than the mean UCS was applied to the specimens in an attempt to identify the brittle-ductile transition of the coal. The new results have been compiled with the previous results in order to re-evaluate the confinement-dependency of the coal behavior. Additionally, the different confining stresses are used as analogs for different width-to-height (W/H) conditions of pillar strength. Although the W/H ratios of the specimens were not directly considered during testing, the equivalent W/H ratios of a pillar as a function of the confining stresses were estimated using an existing empirical solution. According to this relationship, the W/H at which in situ pillar behavior would be expected to transition from brittle to ductile is identified.

Influence of biochar from animal and plant origin on the compressive strength characteristics of degraded landfill surface soils

2020 ◽  
pp. 105678952092552 ◽  
Author(s):  
Manash Jyoti Bora ◽  
Sanandam Bordoloi ◽  
Himanshu Kumar ◽  
Nirmali Gogoi ◽  
Hong-Hu Zhu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Green Infrastructure ◽  
Water Hyacinth ◽  
Unconfined Compressive Strength ◽  
Mechanical Characteristics ◽  
Poultry Litter ◽  
Peanut Shell ◽  
Surface Soils ◽  
Saw Dust ◽  
Landfill Cover

Growing awareness of sustainability in the landfill cover system has increased the use of biochar amendment for degraded landfill surface soils. Hydraulic and vegetative benefits of biochar on cover soil have been studied in the past, while ignoring mechanical characteristics, which is important to understand progressive failure of landfill infrastructure. In this study, the mechanical characteristics of four soil–biochar composites were investigated by conducting 81 unconfined compressive strength test. The results based on four in-house produced biochar were used to study the effect of compaction state (density, moisture content) and biochar percentage (5% and 10%) on unconfined compressive strength of soil–biochar. The ductility of soil–biochar was investigated for all the four biochars. Results from this study indicate a contrasting observation of strength gain depending on the type of biochar. The unconfined compressive strength of soil–biochar is potentially influenced by the different surface functional groups of biochar (hydrophilicity/hydrophobicity) and soil-biochar interlocking. It was noted that the peanut shell biochar gave comparable unconfined compressive strength of soil–biochar with that of bare soil for different compaction state. However, a diminution in the unconfined compressive strength was observed for all the other three soil–biochar sourced from water hyacinth, saw dust, and poultry litter. The study indicates that the use of biochar in soils does not ensure an improvement in the strength of soil–biochar. Enhancement in ductility was found for all the four soil–biochar irrespective of compaction state. Improvement in ductility was maximum when the soil–biochar is compacted at the dry state of optimum. Plant-based biochar has higher potency to increase the ductility of soil as compared to the animal-based biochar. Our study identifies peanut shell biochar ideal for landfill cover amendment material, considering its mechanical characteristics and design criterion. Soil biochar composite from water hyacinth, saw dust, and poultry litter can be used for potential application in green-infrastructure.

scholarly journals Experimental Study on Mechanical Characteristics and Fracture Patterns of Unfrozen/Freezing Saturated Coal and Sandstone

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 992 ◽  
Author(s):  
Chong Wang ◽  
Shuangyang Li ◽  
Tongwei Zhang ◽  
Zhemin You
Keyword(s):  
Phase Transition ◽  
Compressive Strength ◽  
Mechanical Characteristics ◽  
Failure Modes ◽  
Single Plane ◽  
Failure Patterns ◽  
Freezing Method ◽  
Fracture Patterns ◽  
Triaxial Compressive Strength ◽  
Layer Activation

The thermomechanical behavior of coal and sandstone during excavation using the freezing method is a new challenge for coal mining and geotechnical engineering. In this paper, the influence of temperature on the mechanical characteristics and fracture patterns of two types of saturated rocks (coal and sandstone) were investigated. A series of laboratory tests, including the Brazilian tensile strength (BTS), uniaxial compressive strength (UCS), and triaxial compressive strength (TCS), were conducted at temperatures of 20, −4, −10, and −15 °C. The results indicated a significant increase in their strength when the temperature was reduced from 20 to −15 °C, especially near the phase-transition point. Then, a theoretical model was proposed to predict rock strength change with temperature, based on the phase-transition theory. To evaluate this model, the predicted results were compared with experimental data, where a good correlation was identified. In addition, four failure patterns were observed in indirect tensile tests (i.e., layer activation, central fracture, noncentral fracture, and central and layer activation), and three types of failure modes in compression tests (i.e., axial splitting, shearing along a single plane, multiple fracturing). The evolution of the rock damage was divided into four stages: Crack closure, fracture initiation, critical energy release, and rupture. These results could be applied to evaluate and predict the mechanical behavior of saturated coal and sandstone during excavation using the freezing method.

scholarly journals The influence of soft clay saturation characteristics on unconfined compressive strength in Guangdong-Hong Kong-Macao Greater Bay Area

2021 ◽  
Vol 293 ◽  
pp. 02011
Author(s):  
DaShu Guan ◽  
JiaXi Zheng ◽  
WenHao Huang ◽  
JunZhi Zhong ◽  
WenWen Du ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Gas Phase ◽  
Unconfined Compressive Strength ◽  
Shear Failure ◽  
Soft Clay ◽  
Plastic Shear ◽  
Bay Area ◽  
Saturated Clay ◽  
Unsaturated Clay ◽  
Saturated Soft Clay

In order to study the influence of saturated characteristics of soft clay on unconfined compressive strength, the soft clay of Guangdong-Hong Kong-Macao Bay Area is taken as the research object, comparing and contrasting on unconfined compression test of saturated clay and unsaturated clay in laboratory, studying the variation law of unconfined compressive strength and sensitivity of unsaturated and saturated soft clay. The test results show that: 1. During the failure of unsaturated soft clay samples, oblique fractures appear, showing brittle shear failure, while the saturated clay samples appear constant bulging in the middle, and finally a “cross” is broken in the central bulging part, showing plastic shear failure.2. The unconfined compressive strength of unsaturated clay is about 10kPa higher than that of saturated soft clay, and its corresponding sensitivity is also about 0.4 higher. It can be shown that the soil saturation has a certain influence on the soil strength. The difference between saturated soil and unsaturated soil is the existence of gas phase. To be more precise, the existence of gas phase in unsaturated soil, i.e. the existence of suction, makes the soil stronger and presents the brittle shear failure form, while the saturated soil basically presents the plastic shear failure form.

The effect of elevated temperature on the mechanical properties and failure modes of GFRP face sheets and PET foam cored sandwich beams

2018 ◽  
Vol 22 (4) ◽  
pp. 1235-1255
Author(s):  
Mohsen Rezaei ◽  
Vasileios Karatzas ◽  
Christian Berggreen ◽  
Leif A Carlsson
Keyword(s):  
Compressive Strength ◽  
Polyethylene Terephthalate ◽  
Failure Modes ◽  
Shear Failure ◽  
Elevated Temperatures ◽  
Sandwich Beam ◽  
Standard Test ◽  
Sandwich Beams ◽  
The Face ◽  
Failure Loads

The influence of elevated temperatures on stiffness and strength of composite face sheet and polyethylene terephthalate foam cored sandwich beam has been experimentally investigated. Standard test methods and analytical failure models were used to determine the effect of elevated temperatures. The authors examined E-glass/epoxy cross-ply face laminates, polyethylene terephthalate foam, and sandwich beams consisting of glass/epoxy face laminates and polyethylene terephthalate foam core loaded in four-point flexure. The tensile properties of the face laminate were examined over a temperature range from 25 to 175°C. Compression and shear tests on the face laminate, polyethylene terephthalate foam, and sandwich beams were performed at temperatures up to 100°C. The face laminates exhibited moderate reductions of Young’s modulus and tensile strength, while the compressive strength, shear modulus, and shear strength substantially decreased at elevated temperatures. Similarly, the compressive and shear moduli as well as the compressive strength of the polyethylene terephthalate foam decreased substantially by exposure to a temperature of 100°C. The failure mode of the sandwich panels was observed to be highly dependent on temperature, distinguishing three basic failure modes, viz. core shear failure, indentation failure, and face wrinkling. The failure loads associated to these failure modes were calculated using models available in the literature. The failure loads were found to be consistent with the failure predictions and failure modes.

UNDRAINED SHEAR STRENGTH OF SOFT CLAY MIXED WITH DIFFERENT PERCENTAGES OF LIME AND SILICA FUME

2016 ◽  
Vol 78 (8-5) ◽  
Author(s):  
Muzamir Hasan ◽  
Ali Jamal Alrubaye ◽  
Leong Kah Seng ◽  
Mohammad Syafiq Ideris ◽  
Aminaton Marto
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
Silica Fume ◽  
Unconfined Compressive Strength ◽  
Soft Clay ◽  
Cost Effective ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Unconfined Compression Test ◽  
Coefficient Of Permeability

Soil stabilisation, as a cost-effective and environmentally friendly method, is used in the building of systems like roads, dams, canals and river levels. Chemical stabilisation of soil is carried out by adding binder or by-products like lime and silica fume to the soil thereby modifying the geotechnical performance of the soil. Various researchers have carried out research on the properties of soil, such as its compaction, compressibility, hydraulic conductivity, and strength characteristics. The focus of the study was the determination of the physical properties of the soft clay used and the strength of soft clay (kaolin) mixed with 6 % of silica fume and various percentages (3 %, 5 %, 7 % and 9 %) of lime. Unconfined compression test was carried out on the soft clay and the mixtures of soft clay-lime-silica fume to investigate the effect of lime stabilisation with silica fume additives on the unconfined compressive strength of the mixtures. Based on the results obtained, all soil samples were indicated as soils with medium plasticity. From 0 % to 9 % of lime with 6 % of silica fume, the decreased in the maximum dry density was by 5.92 % and the increased in the optimum moisture content was by 23.5 %. Decreased in the coefficient of permeability of the mixtures occurred when compared to the coefficient of permeability of the soft clay itself. The improvement in shear strength of soft clay mixed with 6 % silica fume and 5 % lime was 29.83 % compared to the shear strength of the soft clay sample. The optimal percentage of lime-silica fume combination was attained at 5.0 % of lime and 6.0 % of silica fume in order to improve the shear strength of soft clay. It can be concluded that lime-silica fume additives improved the unconfined compressive strength of the soft clay.

scholarly journals Experimental Investigation on the Mechanical Characteristics and Deformation Behaviour of Fractured Rock-Like Material with One Single Fissure under the Conventional Triaxial Compression

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Taoli Xiao ◽  
Mei Huang ◽  
Cheng Cheng ◽  
Yunlong He
Keyword(s):  
Mechanical Characteristics ◽  
Failure Modes ◽  
Shear Failure ◽  
Early Stage ◽  
Fractured Rock ◽  
Deformation Behaviour ◽  
Triaxial Compression ◽  
Strain Curve ◽  
Confining Pressure ◽  
Material Specimen

An experimental study was carried out on a rock-like material specimen containing a single fissure to investigate its mechanical characteristics and deformation behaviour under triaxial compression. The mechanical characteristics, such as peak strength and residual strength, are discussed. The confining pressure had a distinct effect on the ductility characteristics of the specimen. “A distinct stress drop” occurred in the early stage of the stress-strain curve when the length fissure was relatively long. The I-crack, II-crack, and III-crack are all observed under triaxial compression, and the III-crack is commonly observed under triaxial compression. Confining pressure plays an essential role in affecting the failure mode of the specimen. There are three kinds of failure modes in the triaxial compression experiment on a rock-like material specimen with one single fissure: tensile-shear comprehensive failure, “X”-shaped shear failure, and shear failure along the fissure plane. These results are important and fundamental to understand the fracture mechanism of rock engineering.

scholarly journals Performance of THM behavior of sand-bentonite mixtures considering thermal effect

2021 ◽  
Vol 337 ◽  
pp. 01020
Author(s):  
Tomoyoshi Nishimura ◽  
Junichi Koseki
Keyword(s):  
Compressive Strength ◽  
Relative Humidity ◽  
Compression Test ◽  
Unconfined Compressive Strength ◽  
Triaxial Compression ◽  
Radioactive Waste Disposal ◽  
Unconfined Compression ◽  
Unconfined Compression Test ◽  
Sand Mixture ◽  
High Level

This study presented the overview on the behavior of bentonite-sand mixture used in high level radioactive waste disposal. Both unconfined compression test and triaxial compression test were conducted out that unsaturated-saturated bentonite-sand samples were applied temperature effect below 100 degrees Celsius. Unconfined compressive strength was determined with various temperatures and different relative humidity for unsaturated bentonite-sand specimens, so the growing of pore pressure due to heating was most significant for interpretation to THM behaviour of artificial barrier system compositing bentonite materials.

Sign in / Sign up

Export Citation Format

Share Document