scholarly journals A Novel Ionic Exchange Membrane Crystallizer to Recover Magnesium Hydroxide from Seawater and Industrial Brines

Membranes ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 303
Author(s):  
Daniele La Corte ◽  
Fabrizio Vassallo ◽  
Andrea Cipollina ◽  
Marian Turek ◽  
Alessandro Tamburini ◽  
...  
Keyword(s):  
Magnesium Hydroxide ◽  
Saline Solution ◽  
Low Cost ◽  
Feed Solution ◽  
Ionic Exchange ◽  
The North ◽  
Novel Technology ◽  
Co Precipitation ◽  
Exchange Membrane ◽  
By Products

A novel technology, the ion exchange membrane crystallizer (CrIEM), that combines reactive and membrane crystallization, was investigated in order to recover high purity magnesium hydroxide from multi-component artificial and natural solutions. In particular, in a CrIEM reactor, the presence of an anion exchange membrane (AEM), which separates two-compartment containing a saline solution and an alkaline solution, allows the passage of hydroxyl ions from the alkaline to the saline solution compartment, where crystallization of magnesium hydroxide occurs, yet avoiding a direct mixing between the solutions feeding the reactor. This enables the use of low-cost reactants (e.g., Ca(OH)2) without the risk of co-precipitation of by-products and contamination of the final crystals. An experimental campaign was carried out treating two types of feed solution, namely: (1) a waste industrial brine from the Bolesław Śmiały coal mine in Łaziska Górne (Poland) and (2) Mediterranean seawater, collected from the North Sicilian coast (Italy). The CrIEM was tested in a feed and bleed modality in order to operate in a continuous mode. The Mg2+ concentration in the feed solutions ranges from 0.7 to 3.2 g/L. Magnesium recovery efficiencies from 89 up to 100% were reached, while magnesium hydroxide purity between 94% and 98.8% was obtained.

Open-Hole Completion Based Mechanical Diversion of Acid/Chemical Stimulation Operations: Design, Deployment and Field Trial Results

2015 ◽  
Author(s):  
E. I. Carvajal ◽  
Y.. Caline ◽  
M.. Rylance ◽  
K.. Rice ◽  
J.. Waters ◽  
...  
Keyword(s):  
Field Trial ◽  
Low Cost ◽  
Chemical Stimulation ◽  
Lessons Learned ◽  
The North ◽  
Novel Technology ◽  
Austin Chalk ◽  
Open Hole ◽  
The North Sea ◽  
Efficient Distribution

Abstract The ubiquitous challenge that is faced by chemical stimulation techniques, of any kind, has always been achieving an economic and efficient distribution of the stimulation solution across the exposed reservoir interval. Many have approached this problem from a chemical perspective and others from the use of additives for mechanical diversion; however the very nature of stimulation itself means that a changing injection profile will make efficient diversion by such techniques uncertain and unpredictable. Instead, rather than relying on serendipitous deployment techniques, the approach described and reported here places true mechanical diversion as part of the well construction process. This paper will completely describe the process and achievements to date, including successful application in a number of horizontal wells completed in the Austin Chalk, as part of an overall deployment plan. Essentially, this new completion system comprises of multiple pressure actuated assemblies, distributed along the liner/casing. These assemblies, when activated, allow the lateral deployment of forty-foot needles, radially distributed at ninety-degree phasing around the casing, into the unstimulated reservoir. These subs can be precisely located across pre-selected intervals and thereby provide certainty of acid treatment distribution. The acid is pumped through the needles themselves during stimulation; however production takes place through a suite of ports. A bespoke debris basket may be run, after the stimulation treatment, in order to recover a suite of needle deployment indicators. This run, if performed, effectively establishes the success of the deployment. In order to demonstrate the concept and avoid the high-cost environment of the North Sea, a low cost field trial location was sought and identified. An Austin chalk operator was looked for that had an extensive horizontal candidate well set available for re-completion in open-hole. A number of candidate wells were then identified and the wells were recompleted and stimulated with this new system. This paper will present the entire suite of data related to these deployments, stimulation operations, lessons learned, production impact and potential. This novel technology was greatly assisted, supported and delivered via the Joint Chalk Research (JCR) council, comprising of some ten operating companies that encourage, fund and drive the development of carbonate completion and stimulation solutions.

Systematic Precipitation of Magnesium Hydroxide Using NH4OH to Preparing MgO-PSZ Precursor Powder

2014 ◽  
Vol 805 ◽  
pp. 712-717
Author(s):  
Chieko Yamagata ◽  
Jose O.A. Paschoal
Keyword(s):  
Magnesium Hydroxide ◽  
Room Temperature ◽  
Low Cost ◽  
Zirconium Oxychloride ◽  
Precursor Powder ◽  
Molar Ratio ◽  
Ceramic Processing ◽  
Wide Range ◽  
High Molar Ratio ◽  
Co Precipitation

The wide range of applications of zirconia based ceramics is due to stabilization of its tetragonal and cubic structures at room temperature, by controlled adding of dopants such as yttria, magnesia, calcia, ceria and some rare earth oxides. The advantage of the use of magnesia as dopant is not only due to its low cost, but fact that by controlling its ceramic processing, it is possible to control a specific microstructure for the specific application. The precipitation of magnesium hydroxides, using NH4OH as a precipitant, presents some difficulties due to the formation of a variety of soluble complexes of ammonia with magnesium, which inhibits the total precipitation of magnesium. In the present work, the influence of precipitant and metals concentrations and pH on the magnesium hydroxide precipitation was investigated. Magnesium chloride, zirconium oxychloride and NH4OH were used as starting materials. The precipitation of magnesium hydroxide depends on concentrations of OH-, Cl- and Mg2+. To achieve specific precipitation yield, lower the concentration of Mg2+ high molar ratio of [OH-]/[Cl-] is required. The pH measure is not enough to control Mg (OH)2 precipitation. The use of molar ratio of [OH-]/[Cl-] = 4.4, resulted in 95 % of Mg (OH)2 precipitation. The co-precipitation of Zr and Mg hydroxides, using the optimized molar ratio of [OH-]/[Cl-], the precipitation of Mg (OH)2 achieved in range of 97.6 to 98.3 %.

Understanding the Role of Chlorine and Ozone to Control Postharvest Diseases in Fruit and Vegetables: A Review

2020 ◽  
Vol 16 (4) ◽  
pp. 455-461
Author(s):  
Gabriela M. Baia ◽  
Otniel Freitas-Silva ◽  
Murillo F. Junior
Keyword(s):  
Chlorine Dioxide ◽  
Broad Spectrum ◽  
Fruits And Vegetables ◽  
Low Cost ◽  
Residual Effects ◽  
Pathogenic Microorganisms ◽  
Postharvest Diseases ◽  
Post Harvest ◽  
By Products

Fruits and vegetables are foods that come into contact with various types of microorganisms from planting to their consumption. A lack or poor sanitation of these products after harvest can cause high losses due to deterioration and/ or pathogenic microorganisms. There are practically no post-harvest fungicides or bactericides with a broad spectrum of action that have no toxic residual effects and are safe. However, to minimize such problems, the use of sanitizers is an efficient device against these microorganisms. Chlorine is the most prevalent sanitizing agent because of its broad spectrum, low cost and well-established practices. However, the inevitable formation of disinfection by-products, such as trihalomethanes (THMs) and haloacetic acids (HAAs), is considered one of the main threats to food safety. Alternative sanitizers, such as chlorine dioxide (ClO2) and ozone, are becoming popular as a substitute for traditional post-harvest treatments. Thus, this review addresses the use of chlorine, chlorine dioxide and ozone emphasizing aspects, such as usage, safe application, spectrum of action and legislation. In order to ensure the quality and safety of final products, the adoption of well-prepared sanitation and sanitation programs for post-harvest fruits and vegetables is essential.

scholarly journals Durability of Anion Exchange Membrane Water Electolyzers

2021 ◽  
Author(s):  
Dongguo Li ◽  
Andrew R Motz ◽  
Chulsung Bae ◽  
Cy Fujimoto ◽  
Gaoqiang Yang ◽  
...  
Keyword(s):  
Hydrogen Production ◽  
Anion Exchange ◽  
Low Cost ◽  
Anion Exchange Membrane ◽  
Production Technologies ◽  
Exchange Membrane

Interest in the low-cost production of clean hydrogen is growing. Anion exchange membrane water electrolyzers (AEMWEs) are considered one of the most promising sustainable hydrogen production technologies because of their...

scholarly journals Monomers, Materials and Energy from Coffee By-Products: A Review

2021 ◽  
Vol 13 (12) ◽  
pp. 6921
Author(s):  
Laura Sisti ◽  
Annamaria Celli ◽  
Grazia Totaro ◽  
Patrizia Cinelli ◽  
Francesca Signori ◽  
...  
Keyword(s):  
Circular Economy ◽  
Food Industry ◽  
Food Packaging ◽  
Low Cost ◽  
Biofuel Production ◽  
Material Technology ◽  
Coffee Production ◽  
Coffee Pulp ◽  
Coffee Waste ◽  
By Products

In recent years, the circular economy and sustainability have gained attention in the food industry aimed at recycling food industrial waste and residues. For example, several plant-based materials are nowadays used in packaging and biofuel production. Among them, by-products and waste from coffee processing constitute a largely available, low cost, good quality resource. Coffee production includes many steps, in which by-products are generated including coffee pulp, coffee husks, silver skin and spent coffee. This review aims to analyze the reasons why coffee waste can be considered as a valuable source in recycling strategies for the sustainable production of bio-based chemicals, materials and fuels. It addresses the most recent advances in monomer, polymer and plastic filler productions and applications based on the development of viable biorefinery technologies. The exploration of strategies to unlock the potential of this biomass for fuel productions is also revised. Coffee by-products valorization is a clear example of waste biorefinery. Future applications in areas such as biomedicine, food packaging and material technology should be taken into consideration. However, further efforts in techno-economic analysis and the assessment of the feasibility of valorization processes on an industrial scale are needed.

scholarly journals Evaluation of Electrodialysis Desalination Performance of Novel Bioinspired and Conventional Ion Exchange Membranes with Sodium Chloride Feed Solutions

Membranes ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 217
Author(s):  
AHM Golam Hyder ◽  
Brian A. Morales ◽  
Malynda A. Cappelle ◽  
Stephen J. Percival ◽  
Leo J. Small ◽  
...  
Keyword(s):  
Ion Exchange ◽  
Cation Exchange ◽  
Current Density ◽  
Feed Solution ◽  
Laboratory Scale ◽  
Cation Exchange Membrane ◽  
Limiting Current ◽  
Ion Exchange Membranes ◽  
Experimental Apparatus ◽  
Exchange Membrane

Electrodialysis (ED) desalination performance of different conventional and laboratory-scale ion exchange membranes (IEMs) has been evaluated by many researchers, but most of these studies used their own sets of experimental parameters such as feed solution compositions and concentrations, superficial velocities of the process streams (diluate, concentrate, and electrode rinse), applied electrical voltages, and types of IEMs. Thus, direct comparison of ED desalination performance of different IEMs is virtually impossible. While the use of different conventional IEMs in ED has been reported, the use of bioinspired ion exchange membrane has not been reported yet. The goal of this study was to evaluate the ED desalination performance differences between novel laboratory‑scale bioinspired IEM and conventional IEMs by determining (i) limiting current density, (ii) current density, (iii) current efficiency, (iv) salinity reduction in diluate stream, (v) normalized specific energy consumption, and (vi) water flux by osmosis as a function of (a) initial concentration of NaCl feed solution (diluate and concentrate streams), (b) superficial velocity of feed solution, and (c) applied stack voltage per cell-pair of membranes. A laboratory‑scale single stage batch-recycle electrodialysis experimental apparatus was assembled with five cell‑pairs of IEMs with an active cross-sectional area of 7.84 cm2. In this study, seven combinations of IEMs (commercial and laboratory-made) were compared: (i) Neosepta AMX/CMX, (ii) PCA PCSA/PCSK, (iii) Fujifilm Type 1 AEM/CEM, (iv) SUEZ AR204SZRA/CR67HMR, (v) Ralex AMH-PES/CMH-PES, (vi) Neosepta AMX/Bare Polycarbonate membrane (Polycarb), and (vii) Neosepta AMX/Sandia novel bioinspired cation exchange membrane (SandiaCEM). ED desalination performance with the Sandia novel bioinspired cation exchange membrane (SandiaCEM) was found to be competitive with commercial Neosepta CMX cation exchange membrane.

scholarly journals Characterization of Protein Hydrolysates from Fish Discards and By-Products from the North-West Spain Fishing Fleet as Potential Sources of Bioactive Peptides

Marine Drugs ◽  
2021 ◽  
Vol 19 (6) ◽  
pp. 338
Author(s):  
Andreia Henriques ◽  
José A. Vázquez ◽  
Jesus Valcarcel ◽  
Rogério Mendes ◽  
Narcisa M. Bandarra ◽  
...  
Keyword(s):  
Inhibitory Activity ◽  
Bioactive Peptides ◽  
Radical Scavenging Activity ◽  
Radical Scavenging ◽  
Protein Hydrolysates ◽  
Scavenging Activity ◽  
North West ◽  
Chelating Activity ◽  
The North ◽  
By Products

Fish discards and by-products can be transformed into high value-added products such as fish protein hydrolysates (FPH) containing bioactive peptides. Protein hydrolysates were prepared from different parts (whole fish, skin and head) of several discarded species of the North-West Spain fishing fleet using Alcalase. All hydrolysates had moisture and ash contents lower than 10% and 15%, respectively. The fat content of FPH varied between 1.5% and 9.4% and had high protein content (69.8–76.6%). The amino acids profiles of FPH are quite similar and the most abundant amino acids were glutamic and aspartic acids. All FPH exhibited antioxidant activity and those obtained from Atlantic horse mackerel heads presented the highest 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activity, reducing power and Cu2+ chelating activity. On the other hand, hydrolysates from gurnard heads showed the highest ABTS radical scavenging activity and Fe2+ chelating activity. In what concerns the α-amylase inhibitory activity, the IC50 values recorded for FPH ranged between 5.70 and 84.37 mg/mL for blue whiting heads and whole Atlantic horse mackerel, respectively. α-Glucosidase inhibitory activity of FPH was relatively low but all FPH had high Angiotensin Converting Enzyme (ACE) inhibitory activity. Considering the biological activities, these FPH are potential natural additives for functional foods or nutraceuticals.

scholarly journals Preparation of Porous Hydroxyapatite Using Cetyl Trimethyl Ammonium Bromide as Surfactant for the Removal of Lead Ions from Aquatic Solutions

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1617
Author(s):  
Silviu-Adrian Predoi ◽  
Carmen Steluta Ciobanu ◽  
Mikael Motelica-Heino ◽  
Mariana Carmen Chifiriuc ◽  
Monica Luminita Badea ◽  
...  
Keyword(s):  
Cetyl Trimethyl Ammonium Bromide ◽  
Morphological Changes ◽  
Low Cost ◽  
Lead Ions ◽  
Ammonium Bromide ◽  
Porous Hydroxyapatite ◽  
X Ray ◽  
Composition And Structure ◽  
Cetyl Trimethyl Ammonium ◽  
Co Precipitation

In the present study, a new low-cost bioceramic nanocomposite based on porous hydroxyapatite (HAp) and cetyl trimethyl ammonium bromide (CTAB) as surfactant was successfully obtained by a simple chemical co-precipitation. The composition and structure of the HAp-CTAB were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (TEM), scanning electron microscope (SEM) equipped with an energy dispersive X-ray (EDX) spectrometer, and N2 adsorption/desorption analysis. The capacity of HAp-CTAB nanocomposites to remove the lead ions from aqueous solutions was studied by adsorption batch experiments and proved by Langmuir and Freundlich models. The Pb2+ removal efficiency of HAp-CTAB biocomposite was also confirmed by non-destructive ultrasound studies. The cytotoxicity assays showed that the HAp-CTAB nanocomposites did not induce any significant morphological changes of HeLa cells after 24 h of incubation or other toxic effects. Taken together, our results suggests that the obtained porous HAp-CTAB powder could be used for the decontamination of water polluted with heavy metals, such as Pb2+.

scholarly journals Low-temperature combustion of methane over graphene templated Co3O4 defective-nanoplates

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Dian Gong ◽  
Gaofeng Zeng
Keyword(s):  
Low Temperature ◽  
Transition Metal Oxides ◽  
Active Oxygen Species ◽  
Low Cost ◽  
Thermal Reduction ◽  
Low Temperature Combustion ◽  
Solid Catalysts ◽  
Intermittent Feeding ◽  
Co Precipitation ◽  
Catalytic Combustion Of Methane

AbstractTransition metal oxides are the potential catalysts to replace noble-metal based catalyst for the catalytic combustion of methane due to the tolerable reactivity and low cost. However, these catalysts are challenged by the low temperature reactivity. Herein, the surface defective Co3O4 nanoplates are realized through a facile co-precipitation and thermal reduction method with the association of GO. The resultant catalysts (CoGO50) demonstrate a superior low-temperature reactivity for the methane oxidation to CO2 and H2O in comparison with the common Co3O4 catalyst. The reliable stability of CoGO50 catalyst was proved by 80 h testing with intermittent feeding of water vapor. The experimental analysis demonstrates that the presence of a small amount of GO significantly affects the catalysts in surface valence state, active oxygen species and surface oxygen vacancies through reacting with the cobalt oxide as a reductant. Moreover, GO plays as 2D confine template to form smaller and thinner nanoplates. This work provides a facile method to control the surface properties of catalyst not only for Co3O4 based catalysts but also for wider solid catalysts.

scholarly journals Biodegradable Chitosan Films with ZnO Nanoparticles Synthesized Using Food Industry By-Products—Production and Characterization

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 646
Author(s):  
Victor Gomes Lauriano Souza ◽  
Marta M. Alves ◽  
Catarina F. Santos ◽  
Isabel A. C. Ribeiro ◽  
Carolina Rodrigues ◽  
...  
Keyword(s):  
Zinc Oxide Nanoparticles ◽  
Food Industry ◽  
Low Cost ◽  
Young Modulus ◽  
Barrier Properties ◽  
Zno Nps ◽  
Elongation At Break ◽  
Chitosan Films ◽  
By Products ◽  
Different Levels

This work aimed to produce bionanocomposites of chitosan incorporated with zinc oxide nanoparticles (ZnO NPs) synthesized using food industry by-products and to characterize them. Such nanoparticles are highlighted due to their low cost, antimicrobial activity, accessibility, and sustainability synthesis. Four different levels of ZnO NPs (0, 0.5, 1.0, and 2.0% w/w of chitosan) were tested, and the bionanocomposites were characterized in terms of their hydrophobicity, mechanical, optical, and barrier properties. Overall, the incorporation of ZnO NPs changed the composites from brittle to ductile, with enhanced elongation at break and reduced Young Modulus and tensile strength. Thus, ZnO NPs acted as plasticizer, turning the films more flexible, due to the presence of organic compounds on the NPs. This also favored permeability of oxygen and of water vapor, but the good barrier properties were maintained. Optical properties did not change statistically with the ZnO NPs incorporation. Thus, the characterization presented in this paper may contribute to support a decision on the choice of the material’s final application.

Sign in / Sign up

Export Citation Format

Share Document