scholarly journals Correlation between Microstructure and Mechanical Properties of Heat-Treated Ti–6Al–4V with Fe Alloying

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 854 ◽  
Author(s):  
Yongwei Liu ◽  
Fuwen Chen ◽  
Guanglong Xu ◽  
Yuwen Cui ◽  
Hui Chang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Phase Interface ◽  
High Strength ◽  
High Plasticity ◽  
High Aging Temperature ◽  
Microstructure And Mechanical Properties

The microstructure and mechanical properties of a newly developed Fe-microalloyed Ti–6Al–4V titanium alloy were investigated after different heat treatments. The volume fraction and the morphological features of the lamellar α phase had significant effects on the alloy’s mechanical performance. A dataset showing the relationship between microstructural features and tensile strength, elongation, and fracture toughness was developed. A high aging temperature resulted in high plasticity and fracture toughness, but relatively low strength. The high strength favored the fine α and the slender β. The high aspect ratio of lamellar α led to high strength but low fracture toughness. The alloy with ~84 vol % α exhibited the highest strength and lowest fracture toughness because the area of its α/β-phase interface was the highest. Optimal comprehensive mechanical performance and heat-treatment procedures were thus obtained from the dataset. Optimal tensile strength, yield strength, elongation, and fracture toughness were 999 and 919 MPa, 10.4%, and 94.4 MPa·m1/2, respectively.

Microstructure and Mechanical Performance of AZ31-1.7 Wt.% Si Alloy Processed by Cyclic Channel Die Compression

2010 ◽  
Vol 667-669 ◽  
pp. 457-461
Author(s):  
Wei Guo ◽  
Qu Dong Wang ◽  
Man Ping Liu ◽  
Tao Peng ◽  
Xin Tao Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Chinese Script ◽  
Cast State ◽  
Microstructure And Mechanical Properties ◽  
Mean Grain Size ◽  
The Matrix ◽  
The Mean

Cyclic channel die compression (CCDC) of AZ31-1.7 wt.% Si alloy was performed up to 5 passes at 623 K in order to investigate the microstructure and mechanical properties of compressed alloys. The results show that multi-pass CCDC is very effective to refine the matrix grain and Mg2Si phases. After the alloy is processed for 5 passes, the mean grain size decreases from 300 μm of as-cast to 8 μm. Both dendritic and Chinese script type Mg2Si phases break into small polygonal pieces and distribute uniformly in the matrix. The tensile strength increases prominently from 118 MPa to 216 MPa, whereas the hardness of alloy deformed 5 passes only increase by 8.4% compared with as-cast state.

An assessment into mechanical properties and microstructural behavior of TIG welded Ti-6Al-4V titanium alloy

2020 ◽  
Vol 10 (3) ◽  
pp. 281-292 ◽  
Author(s):  
Saurabh Dewangan ◽  
Suraj Kumar Mohapatra ◽  
Abhishek Sharma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
High Strength ◽  
Hardness Test ◽  
Content Type ◽  
Ti Alloys ◽  
Microstructure And Mechanical Properties ◽  
Grade 5 ◽  
Selection Of

PurposeTitanium (Ti) alloys are in high demand in manufacturing industries all over the world. The property like high strength to weight ratio makes Ti alloys highly recommended for aerospace industries. Ti alloys possess good weldability, and therefore, they were extensively investigated with regard to strength and metallurgical properties of welded joint. This study aims to deal with the analysis of strength and microstructural changes in Ti-6Al-4V (Grade 5) alloy after tungsten inert gas (TIG) welding.Design/methodology/approachTwo pair of Ti alloy plates were welded in two different voltages, i.e. 24 and 28 V, with keeping the current constant, i.e. 80 A It was a random selection of current and voltage values to check the performance of welded material. Both the welded plates were undergone through some mechanical property analysis like impact test, tensile test and hardness test. In addition, the microstructure of the welded joints was also analyzed.FindingsIt was found that hardness and tensile properties gets improved with an increment in voltage, but this effect was reverse for impact toughness. A good corroboration between microstructure and mechanical properties, such as tensile strength, hardness and toughness, was reported in this work. Heat distribution in both the welded plates was simulated through ANSYS software to check the temperature contour in the plates.Originality/valueA good corroboration between microstructure and mechanical properties, such as tensile strength, hardness and toughness, was reported in this study.

scholarly journals The Effects of Water and Seawater on the Mechanical Properties of Carbon Fibre Reinforced Epoxy Composite under Pre-Cure Curing Condition

1998 ◽  
Vol 7 (4) ◽  
pp. 096369359800700
Author(s):  
M. Zhang ◽  
S.E. Mason
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Carbon Fibre ◽  
Laminate Composite ◽  
Mechanical Performance ◽  
Epoxy Composite ◽  
Interlaminar Fracture Toughness ◽  
Curing Condition ◽  
Structural Carbon

The influences on the interlaminar fracture toughness (GIC) and ultimate tensile strength (UTS) of a cured structural carbon fibre reinforced epoxy composite of two contaminants, water and seawater, introduced prior to cure have been investigated. The results have demonstrated that the control of environmental factors such as water and seawater can have significant effects on the mechanical performance of laminate composite components during the manufacturing process.

Effect of reactive and non-reactive diluents on thermal and mechanical properties of epoxy resin

2017 ◽  
Vol 30 (10) ◽  
pp. 1159-1168 ◽  
Author(s):  
Animesh Sinha ◽  
Nazrul Islam Khan ◽  
Subhankar Das ◽  
Jiawei Zhang ◽  
Sudipta Halder
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Polyethylene Glycol ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Thermal And Mechanical Properties ◽  
Minor Variation ◽  
Reactive Diluents

The effect of reactive (polyethylene glycol) and non-reactive (toluene) diluents on thermal and mechanical properties (tensile strength, hardness and fracture toughness) of diglycidyl ether of bisphenol A epoxy resin (cured by triethylenetetramine) was investigated. The thermal stability and mechanical properties of the epoxy resin modified with reactive and non-reactive diluents at different wt% were investigated using thermo-gravimetric analyser, tensile test, hardness test and single-edge-notched bend test. A minor variation in thermal stability was observed for epoxy resin after addition of polyethylene glycol and toluene at 0.5 wt%; however, further addition of reactive and non-reactive diluents diminished the thermal stability. The addition of 10 wt% of polyethylene glycol in epoxy resin significantly enhances the tensile strength (∼12%), hardness (∼14%) and fracture toughness (∼24%) when compared to that of neat epoxy resin. In contrast, major drop in mechanical performance was observed after addition of toluene in epoxy. Furthermore, fracture surfaces were investigated under field emission scanning electron microscope to elucidate the failure mechanism.

scholarly journals Tailoring the Mechanical Performance of Epoxy Resin by Various Nanoparticles

2008 ◽  
Vol 16 (8) ◽  
pp. 527-533 ◽  
Author(s):  
Sheng Liu ◽  
Hui Zhang ◽  
Zhong Zhang ◽  
Taihua Zhang ◽  
Stephan Sprenger
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Epoxy Resin ◽  
Silica Nanoparticles ◽  
Mechanical Performance ◽  
Sol Gel ◽  
Nanoparticle Dispersion ◽  
Nanosilica Particles ◽  
The Cost

Flexible organic elastomeric nanoparticles (ENP) and two kinds of rigid inorganic silica nanoparticles were dispersed respectively into a bisphenol-A epoxy resin in order to tailor and compare the performance of mechanical properties. It was found that the well-dispersed flexible ENP greatly enhanced the toughness of the epoxy with the cost of modulus and strength. Comparatively, the rigid silica nanoparticles improved Young's modulus, tensile strength and fracture toughness simultaneously. Both fumed and sol-gel-formed nanosilica particles conducted similar results in reinforcing the epoxy resin, although the latter exhibited almost perfect nanoparticle dispersion in matrix. The toughening mechanisms of nanocomposites were further discussed based on fractographic analysis.

scholarly journals Mechanical properties and microstructure of recycled mortar reinforced with hybrid fiber

2018 ◽  
Vol 7 (4) ◽  
pp. 2178 ◽  
Author(s):  
Sallehan Ismail ◽  
Mohammad Asri Abd Hamid ◽  
Zaiton Yaacob ◽  
Dzulkarnaen Ismail ◽  
Hazizan Md Akil
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Mechanical Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
High Strength ◽  
Strength Properties ◽  
Recycled Aggregate ◽  
Hybrid Fiber ◽  
Hybrid Fibers

This study investigated the hybrid effects of two types of microfiber, namely, polypropylene and nylon, on the mechanical properties of high-strength mortar, which produced fine recycled aggregate (FRA). The amount of microfibers was maintained at a volumetric fraction of 0.6%. The microstructure and mechanical strength properties (compressive strength and flexural strength) of recycled mortar reinforced with hybrid-size microfibers were evaluated at various curing ages. Experimental results show that the inclusion of hybrid fibers significantly influenced the mechanical performance of the recycled mortar. The hybridization fiber at volume fraction 0.3% polypropylene + 0.3% nylon yielded the most promising mechanical performance. Enhancements of 8% on compressive and 11% flexural strength were achieved at 28 days. Scanning electron microscopy observations revealed that reinforcement at the microscale prohibited the initiation and growth of cracks at the micro level. High loads were required to form macrocracks within composites, thereby improving the mechanical strength of the mortar matrix.  

Effects of Gd on the Microstructure and Mechanical Properties of Mg-3Sn Alloys

2013 ◽  
Vol 747-748 ◽  
pp. 245-250 ◽  
Author(s):  
Jun Luo ◽  
Rong Shi Chen ◽  
En Hou Han
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Volume Fraction ◽  
Microstructure And Mechanical Properties ◽  
Elongation To Failure ◽  
New Phase

The microstructure and mechanical properties of as-cast Mg-3Sn-xGd (x=0, 0.2, 1 wt.%) alloys were studied by using OM, SEM, EDX, XRD etc. With the increase of Gd, the formation of Mg2Sn phase was impeded and the MgSnGd phase formed and the volume fraction of this new phase obviously increased. The ultimate tensile strength and elongation to failure increased with dilute Gd addition but sharply decreased when the Gd addition comes to 1.34 wt.%. The possible reasons for the variation in microstructure and mechanical properties were discussed.

Mechanical Properties of Modified Polypropylene Coarse Fiber-Reinforced, High-Strength, Lightweight Concrete

2011 ◽  
Vol 374-377 ◽  
pp. 1499-1506
Author(s):  
Rong Hui Zhang ◽  
Jian Li
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Volume Fraction ◽  
High Strength ◽  
Lightweight Aggregate Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume

In this study, the effect of micro-expansion high strength grouting material (EGM) and Modified polypropylene coarse fiber (M-PP fiber) on the mechanical properties of lightweight concrete are investigated. The influence of EGM and M-PP fiber on compressive strength , flexural strength and drying shrinkage of concrete are researched, and flexural fracture toughness are calculated. Test results show that the effect of EGM and M-PP fiber volume fraction (Vf) on flexural strength and fracture toughness is extremely prominent, compressive strength is only slightly enhanced, and the rate of shrinkage is obviously decreased. It is observed that the shape of the descending branch of load-deflection and the ascending branch of shrinkage-age tends towards gently with the increase of Vf. And M-PP fiber reinforced lightweight aggregate concrete is more economical.

scholarly journals The Effect of Extrusion Temperatures on Microstructure and Mechanical Properties of Mg-1.3Zn-0.5Ca (wt.%) Alloys

Crystals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1228
Author(s):  
Honglin Zhang ◽  
Zhigang Xu ◽  
Laszlo J. Kecskes ◽  
Sergey Yarmolenko ◽  
Jagannathan Sankar
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Volume Fraction ◽  
Fiber Texture ◽  
Extrusion Ratio ◽  
Tensile Yield Strength ◽  
Microstructure And Mechanical Properties ◽  
Average Size

The present work mainly investigated the effect of extrusion temperatures on the microstructure and mechanical properties of Mg-1.3Zn-0.5Ca (wt.%) alloys. The alloys were subjected to extrusion at 300 °C, 350 °C, and 400 °C with an extrusion ratio of 9.37. The results demonstrated that both the average size and volume fraction of dynamic recrystallized (DRXed) grains increased with increasing extrusion temperature (DRXed fractions of 0.43, 0.61, and 0.97 for 300 °C, 350 °C, and 400 °C, respectively). Moreover, the as-extruded alloys exhibited a typical basal fiber texture. The alloy extruded at 300 °C had a microstructure composed of fine DRXed grains of ~1.54 µm and strongly textured elongated unDRXed grains. It also had an ultimate tensile strength (UTS) of 355 MPa, tensile yield strength (TYS) of 284 MPa, and an elongation (EL) of 5.7%. In contrast, after extrusion at 400 °C, the microstructure was almost completely DRXed with a greatly weakened texture, resulting in an improved EL of 15.1% and UTS of 274 MPa, TYS of 220 MPa. At the intermediate temperature of 350 °C, the alloy had a UTS of 298 MPa, TYS of 234 MPa, and EL of 12.8%.

Additive manufacturing of high-strength weathering steel parts fabricated by gas tungsten arc: Microstructure and mechanical properties

2019 ◽  
Vol 233 (11) ◽  
pp. 2127-2137 ◽  
Author(s):  
Jun Xiong ◽  
Yue Mao ◽  
Huihui Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
High Strength ◽  
Weathering Steel ◽  
Middle Region ◽  
Gas Tungsten Arc ◽  
Microstructure And Mechanical Properties ◽  
Gas Tungsten ◽  
Deposition Height

This study focuses on microstructure and mechanical properties as a function of location in additively manufactured high-strength weathering steel components using gas tungsten arc as the heat source. Variations of microstructure and mechanical properties in various locations are presented and analysed. The as-deposited high-strength weathering steel is composed of columnar grain morphology with proeutectoid ferrite, acicular ferrite, side plate ferrite and a small amount of pearlite microstructure in the top region, equiaxed grains with ferrite and pearlite in the middle region, and columnar grains in the near-substrate region with the microstructure similar to that in the top region. There exist obvious layer bands in the middle region, and the forming mechanism of the bands is addressed. Microhardness measurement and tensile strength testing indicate obvious changes in different regions, depending on location and direction of testing specimens. The microhardness in the middle region is inferior to that in both near-substrate and top regions. The ultimate tensile strengths in the travel and deposition height directions are approximately 553 and 506 MPa, respectively. Different locations exhibit heterogeneous tensile strength and elongation due to various microstructures and boundaries. The results indicate the feasibility to fabricate high-strength weathering steel components with good tensile properties using gas tungsten arc–based additive manufacturing.

Sign in / Sign up

Export Citation Format

Share Document