scholarly journals Tailoring the Mechanical Performance of Epoxy Resin by Various Nanoparticles

2008 ◽  
Vol 16 (8) ◽  
pp. 527-533 ◽  
Author(s):  
Sheng Liu ◽  
Hui Zhang ◽  
Zhong Zhang ◽  
Taihua Zhang ◽  
Stephan Sprenger
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Epoxy Resin ◽  
Silica Nanoparticles ◽  
Mechanical Performance ◽  
Sol Gel ◽  
Nanoparticle Dispersion ◽  
Nanosilica Particles ◽  
The Cost

Flexible organic elastomeric nanoparticles (ENP) and two kinds of rigid inorganic silica nanoparticles were dispersed respectively into a bisphenol-A epoxy resin in order to tailor and compare the performance of mechanical properties. It was found that the well-dispersed flexible ENP greatly enhanced the toughness of the epoxy with the cost of modulus and strength. Comparatively, the rigid silica nanoparticles improved Young's modulus, tensile strength and fracture toughness simultaneously. Both fumed and sol-gel-formed nanosilica particles conducted similar results in reinforcing the epoxy resin, although the latter exhibited almost perfect nanoparticle dispersion in matrix. The toughening mechanisms of nanocomposites were further discussed based on fractographic analysis.

Effect of reactive and non-reactive diluents on thermal and mechanical properties of epoxy resin

2017 ◽  
Vol 30 (10) ◽  
pp. 1159-1168 ◽  
Author(s):  
Animesh Sinha ◽  
Nazrul Islam Khan ◽  
Subhankar Das ◽  
Jiawei Zhang ◽  
Sudipta Halder
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Polyethylene Glycol ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Thermal And Mechanical Properties ◽  
Minor Variation ◽  
Reactive Diluents

The effect of reactive (polyethylene glycol) and non-reactive (toluene) diluents on thermal and mechanical properties (tensile strength, hardness and fracture toughness) of diglycidyl ether of bisphenol A epoxy resin (cured by triethylenetetramine) was investigated. The thermal stability and mechanical properties of the epoxy resin modified with reactive and non-reactive diluents at different wt% were investigated using thermo-gravimetric analyser, tensile test, hardness test and single-edge-notched bend test. A minor variation in thermal stability was observed for epoxy resin after addition of polyethylene glycol and toluene at 0.5 wt%; however, further addition of reactive and non-reactive diluents diminished the thermal stability. The addition of 10 wt% of polyethylene glycol in epoxy resin significantly enhances the tensile strength (∼12%), hardness (∼14%) and fracture toughness (∼24%) when compared to that of neat epoxy resin. In contrast, major drop in mechanical performance was observed after addition of toluene in epoxy. Furthermore, fracture surfaces were investigated under field emission scanning electron microscope to elucidate the failure mechanism.

scholarly journals The Effects of Water and Seawater on the Mechanical Properties of Carbon Fibre Reinforced Epoxy Composite under Pre-Cure Curing Condition

1998 ◽  
Vol 7 (4) ◽  
pp. 096369359800700
Author(s):  
M. Zhang ◽  
S.E. Mason
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Carbon Fibre ◽  
Laminate Composite ◽  
Mechanical Performance ◽  
Epoxy Composite ◽  
Interlaminar Fracture Toughness ◽  
Curing Condition ◽  
Structural Carbon

The influences on the interlaminar fracture toughness (GIC) and ultimate tensile strength (UTS) of a cured structural carbon fibre reinforced epoxy composite of two contaminants, water and seawater, introduced prior to cure have been investigated. The results have demonstrated that the control of environmental factors such as water and seawater can have significant effects on the mechanical performance of laminate composite components during the manufacturing process.

scholarly journals Correlation between Microstructure and Mechanical Properties of Heat-Treated Ti–6Al–4V with Fe Alloying

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 854 ◽  
Author(s):  
Yongwei Liu ◽  
Fuwen Chen ◽  
Guanglong Xu ◽  
Yuwen Cui ◽  
Hui Chang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Phase Interface ◽  
High Strength ◽  
High Plasticity ◽  
High Aging Temperature ◽  
Microstructure And Mechanical Properties

The microstructure and mechanical properties of a newly developed Fe-microalloyed Ti–6Al–4V titanium alloy were investigated after different heat treatments. The volume fraction and the morphological features of the lamellar α phase had significant effects on the alloy’s mechanical performance. A dataset showing the relationship between microstructural features and tensile strength, elongation, and fracture toughness was developed. A high aging temperature resulted in high plasticity and fracture toughness, but relatively low strength. The high strength favored the fine α and the slender β. The high aspect ratio of lamellar α led to high strength but low fracture toughness. The alloy with ~84 vol % α exhibited the highest strength and lowest fracture toughness because the area of its α/β-phase interface was the highest. Optimal comprehensive mechanical performance and heat-treatment procedures were thus obtained from the dataset. Optimal tensile strength, yield strength, elongation, and fracture toughness were 999 and 919 MPa, 10.4%, and 94.4 MPa·m1/2, respectively.

Morphology and Mechanical Properties of Epoxy/Alumina Nanocomposites

2006 ◽  
Vol 312 ◽  
pp. 233-236 ◽  
Author(s):  
Ke Wang ◽  
Pascal Ogier ◽  
Chauhari Wuiwui Tjiu ◽  
Chaobin He
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Epoxy Resin ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Fracture Mechanisms ◽  
Elongation At Break ◽  
Filler Dispersion ◽  
Morphology And Mechanical Properties

Alumina nano-crystals were dispersed in epoxy resin via different approaches. The effects of filler dispersion on the mechanical properties of the epoxy/alumina nanocomposites were studied. The fracture mechanisms are investigated using SEM. The results show that the Young’s modulus, tensile strength, elongation at break and fracture toughness of epoxy were improved dramatically with the incorporation of well-dispersed alumina nano-crystals. The poorly-dispersed nano-crystals, however, showed little effects on the mechanical properties.

KAISER ALUMINUM ALLOY 7050

Alloy Digest ◽  
2000 ◽  
Vol 49 (1) ◽  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Heat Treating ◽  
High Fracture Toughness ◽  
High Fracture ◽  
Kaiser Aluminum ◽  
Structural Parts ◽  
Very High

Abstract Kaiser Aluminum Alloy 7050 has very high mechanical properties including tensile strength, high fracture toughness, and a high resistance to exfoliation and stress-corrosion cracking. The alloy is typically used in aircraft structural parts. This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength as well as fracture toughness and fatigue. It also includes information on forming, heat treating, machining, and joining. Filing Code: AL-366. Producer or source: Tennalum, A Division of Kaiser Aluminum.

scholarly journals Enhanced Tensile Strength of Monolithic Epoxy with Highly Dispersed TiO2-Graphene Nanocomposites

2021 ◽  
Vol 5 (7) ◽  
pp. 191
Author(s):  
Yanshuai Wang ◽  
Siyao Guo ◽  
Biqin Dong ◽  
Feng Xing
Keyword(s):  
Tensile Strength ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Chemical Properties ◽  
High Mechanical Property ◽  
Graphene Nanocomposites ◽  
Highly Dispersed ◽  
Dispersion State ◽  
Physical And Chemical

The functionalization of graphene has been reported widely, showing special physical and chemical properties. However, due to the lack of surface functional groups, the poor dispersibility of graphene in solvents strongly limits its engineering applications. This paper develops a novel green “in-situ titania intercalation” method to prepare a highly dispersed graphene, which is enabled by the generation of the titania precursor between the layer of graphene at room temperature to yield titania-graphene nanocomposites (TiO2-RGO). The precursor of titania will produce amounts of nano titania between the graphene interlayers, which can effectively resist the interfacial van der Waals force of the interlamination in graphene for improved dispersion state. Such highly dispersed TiO2-RGO nanocomposites were used to modify epoxy resin. Surprisingly, significant enhancement of the mechanical performance of epoxy resin was observed when incorporating the titania-graphene nanocomposites, especially the improvements in tensile strength and elongation at break, with 75.54% and 176.61% increases at optimal usage compared to the pure epoxy, respectively. The approach presented herein is easy and economical for industry production, which can be potentially applied to the research of high mechanical property graphene/epoxy composite system.

Effect of toughened polyamide-coated carbon fiber fabric on the mechanical performance and fracture toughness of CFRP

2021 ◽  
pp. 002199832199945
Author(s):  
Jong H Eun ◽  
Bo K Choi ◽  
Sun M Sung ◽  
Min S Kim ◽  
Joon S Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Photoelectron Spectroscopy ◽  
Mechanical Performance ◽  
Epoxy Composites ◽  
Scanning Calorimetry ◽  
Internal Damage ◽  
Impact Tests ◽  
Flexural Tests ◽  
The Impact

In this study, carbon/epoxy composites were manufactured by coating with a polyamide at different weight percentages (5 wt.%, 10 wt.%, 15 wt.%, and 20 wt.%) to improve their impact resistance and fracture toughness. The chemical reaction between the polyamide and epoxy resin were examined by fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray photoelectron spectroscopy. The mechanical properties and fracture toughness of the carbon/epoxy composites were analyzed. The mechanical properties of the carbon/epoxy composites, such as transverse flexural tests, longitudinal flexural tests, and impact tests, were investigated. After the impact tests, an ultrasonic C-scan was performed to reveal the internal damage area. The interlaminar fracture toughness of the carbon/epoxy composites was measured using a mode I test. The critical energy release rates were increased by 77% compared to the virgin carbon/epoxy composites. The surface morphology of the fractured surface was observed. The toughening mechanism of the carbon/epoxy composites was suggested based on the confirmed experimental data.

Natural Rubber Reinforced with Silica Nanoparticles Extracted from Jasmine and Riceberry Rice Husk Ashes

2018 ◽  
Vol 936 ◽  
pp. 31-36 ◽  
Author(s):  
Wichudaporn Seangyen ◽  
Paweena Prapainainar ◽  
Pongdhorn Sae-Oui ◽  
Surapich Loykulnant ◽  
Peerapan Dittanet
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Silica Nanoparticles ◽  
Rice Husk ◽  
Sol Gel ◽  
Rubber Matrix ◽  
Reinforcing Fillers ◽  
Rubber Nanocomposites ◽  
Jasmine Rice ◽  
20 Nm

Silica nanoparticles were synthesized by rice husk ash (RHA) produced from jasmine rice husk and riceberry rice husk via sol-gel method for the use as reinforcing fillers in natural rubber (NR). The obtained silica nanoparticles are spherical in shape and the particle sizes were observed to be in the 10-20 nm range with uniformly size distribution. The surface of silica nanoparticles was treated with a silane coupling agent confirmed by FTIR. The treated silica nanoparticles were then incorporated into NR and vulcanized with electron beam irradiation. The rubber nanocomposites with silica nanoparticles, produced from jasmine rice husk and riceberry rice husk, resulted in higher mechanical properties (tensile strength and modulus) than neat rubber vulcanizate. The modified rubber vulcanizates revealed rougher surface with tear lines as compared to the neat rubber vulcanizates, indicating the improved strength. Interestingly, the rubber nanocomposites with silica nanoparticles from jasmine rice husk showed higher tensile strength and modulus than silica nanoparticles produced from riceberry rice husk. The micrographs indicated better dispersion of NR composites with jasmine rice husk which leads to a strong interaction between silica nanoparticles and rubber matrix, thereby improving the strength.

Microstructure and Mechanical Performance of AZ31-1.7 Wt.% Si Alloy Processed by Cyclic Channel Die Compression

2010 ◽  
Vol 667-669 ◽  
pp. 457-461
Author(s):  
Wei Guo ◽  
Qu Dong Wang ◽  
Man Ping Liu ◽  
Tao Peng ◽  
Xin Tao Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Chinese Script ◽  
Cast State ◽  
Microstructure And Mechanical Properties ◽  
Mean Grain Size ◽  
The Matrix ◽  
The Mean

Cyclic channel die compression (CCDC) of AZ31-1.7 wt.% Si alloy was performed up to 5 passes at 623 K in order to investigate the microstructure and mechanical properties of compressed alloys. The results show that multi-pass CCDC is very effective to refine the matrix grain and Mg2Si phases. After the alloy is processed for 5 passes, the mean grain size decreases from 300 μm of as-cast to 8 μm. Both dendritic and Chinese script type Mg2Si phases break into small polygonal pieces and distribute uniformly in the matrix. The tensile strength increases prominently from 118 MPa to 216 MPa, whereas the hardness of alloy deformed 5 passes only increase by 8.4% compared with as-cast state.

Mechanical Properties of ABS Embedded with Basalt Fiber Fillers

2016 ◽  
Vol 16 (2) ◽  
pp. 69-74 ◽  
Author(s):  
Ayman M. M. Abdelhaleem ◽  
Mohammed Y. Abdellah ◽  
Hesham I. Fathi ◽  
Montasser Dewidar
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Low Cost ◽  
Basalt Fiber ◽  
Acrylonitrile Butadiene Styrene ◽  
Hardness Test ◽  
Basalt Fibers ◽  
Notched Strength ◽  
The Cost ◽  
Plastic Injection

AbstractAcrylonitrile-butadiene-styrene (ABS) has great verity applications in aerospace and automobiles industries. Mechanical strength of the ABS is superior to even that of impact resistant polystyrene. In addition metallic coatings can be applied to the surface of ABS moldings. The main aim of the present work is to investigate the mechanical properties of additives of basalt fibers (BF) to ABS with (5, 10, and 15) wt% embedded into the polymer matrix by using plastic injection molding technique. This new perceptions has been done on basalt fibers that have a potential low cost with its good mechanical performance. The ultimate tensile strength that obtained from the composite with 15 wt% is 56.67 MPa with 40.52 % increase value than neat ABS, Young’s modulus gradually increases with increasing the amount of additives. Impact un-notched strength decreases with a reported increment of 24.617 KJ.m–2. A Rockwell hardness test is also used and with the increases of additives the amount of hardness of the composite increases. A scan electron microscopy (SEM) on the fracture surface is captured to check the morphologies structure of the composite comparable with a neat ABS. and it is showed a very good distribution and bonding of the B.F. with the pure ABS. As well as the cost of the ABS and BF is reduced by a percentage of 15 %.

Sign in / Sign up

Export Citation Format

Share Document