scholarly journals Improving Mechanical Properties of Mg–Sc Alloy by Surface AZ31 Layer

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 2021
Author(s):  
Cheng Zhang ◽  
Cheng Peng ◽  
Jin Huang ◽  
Yanchun Zhao ◽  
Tingzhuang Han ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Hot Extrusion ◽  
Grain Structure ◽  
Gradient Structure ◽  
Alloy Structure ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Gradient Microstructure ◽  
Solution Strengthening ◽  
Dislocation Strengthening

Building a gradient structure inside the Mg alloy structure can be expected to greatly improve its comprehensive mechanical properties. In this study, AZ31/Mg–Sc laminated composites with gradient grain structure were prepared by hot extrusion. The microstructure and mechanical properties of the Mg–1Sc alloy with different extrusion temperatures and surface AZ31 fine-grain layers were investigated. The alloy has a more obvious gradient microstructure when extruded at 350 °C. The nanoscale hardness value of Mg–1Sc alloy was improved through fine-grain strengthening and solution strengthening of the surface AZ31 fine-grain layer. The strength of Mg–1Sc alloy was improved due to the fine-grain strengthening and dislocation strengthening of the surface AZ31 fine-grain layer, and the elongation of Mg–1Sc alloy was increased by improving the distribution of the microstructure.

Effect of Co on microstructure and mechanical properties of precipitation hardening stainless steel

2020 ◽  
Vol 117 (1) ◽  
pp. 116
Author(s):  
Xiang LV ◽  
De-ning Zou ◽  
Jiao Li ◽  
Yang Pang ◽  
Yu-nong Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Stainless Steel ◽  
Precipitation Hardening ◽  
Volume Fraction ◽  
X Ray ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Transmission Electron ◽  
Solution Strengthening

The effects of Co element on the microstructure of precipitation hardening stainless steel was investigated by metallographic microscope (OM), transmission electron microscopy (TEM) and X-ray diffractometry (XRD), and the mechanical properties were measured by tensile, hardness and impact tests. The results show that with increasing Co content, the volume fraction of reversion austenite is increased. The precipitation of ε-Cu phase is remarkably decreased, leading to the improvement of ductility, while the strength and hardness are decreased. Co element improves the strength and toughness of stainless steel through fine-grain strengthening, solution strengthening and austenitic toughening.

Microstructure and Mechanical Properties of Backward-Extruded Mg-Zn-xCa Biomaterials

2013 ◽  
Vol 747-748 ◽  
pp. 426-430
Author(s):  
Xue Jun Li ◽  
Hui Li ◽  
Shuang Shuang Zhao ◽  
Ning Ma ◽  
Qiu Ming Peng
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Solid Solution Strengthening ◽  
Backward Extrusion ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Microstructure And Mechanical Properties ◽  
Solution Strengthening ◽  
Extrusion Technology ◽  
Precipitate Strengthening

The Mg-1.0Zn-xCa (x=0.2, 0.5, 0.8, 1 wt. %) alloys were prepared by zone solidification and backward extrusion technology. The microstructure and mechanical properties of backward-extruded Mg-1.0Zn-xCa alloys were investigated. The results showed that these backward-extruded Mg-1.0Zn-xCa alloys were mainly composed of equi-axed pentagon-shaped grains and some Mg0.9Zn0.03 precipitates. The tensile and compressive strengths of backward-extruded Mg-1.0Zn-xCa alloys were greatly improved. The improved mechanical properties are mostly attributed to fine grain strengthening, solid solution strengthening and precipitate strengthening. The results demonstrated that the micro alloying of Ca element was one of effective method to improve the mechanical properties of Mg-1.0Zn based biomaterials.

scholarly journals Effect of Sm Doping on the Microstructure, Mechanical Properties and Shape Memory Effect of Cu-13.0Al-4.0Ni Alloy

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4007
Author(s):  
Qimeng Zhang ◽  
Bo Cui ◽  
Bin Sun ◽  
Xin Zhang ◽  
Zhizhong Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Strengthening Effect ◽  
Face Centered Cubic ◽  
Compressive Fracture ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Face Centered

The effects of rare earth element Sm on the microstructure, mechanical properties, and shape memory effect of the high temperature shape memory alloy, Cu-13.0Al-4.0Ni-xSm (x = 0, 0.2 and 0.5) (wt.%), are studied in this work. The results show that the Sm addition reduces the grain size of the Cu-13.0Al-4.0Ni alloy from millimeters to hundreds of microns. The microstructure of the Cu-13.0Al-4.0Ni-xSm alloys are composed of 18R and a face-centered cubic Sm-rich phase at room temperature. In addition, because the addition of the Sm element enhances the fine-grain strengthening effect, the mechanical properties and the shape memory effect of the Cu-13.0Al-4.0Ni alloy were greatly improved. When x = 0.5, the compressive fracture stress and the compressive fracture strain increased from 580 MPa, 10.5% to 1021 MPa, 14.8%, respectively. When the pre-strain is 10%, a reversible strain of 6.3% can be obtained for the Cu-13.0Al-4.0Ni-0.2Sm alloy.

In Situ Preparation and Mechanical Properties of (ZrB2+ZrC)/Zr3[Al(Si)]4C6 Composites

2014 ◽  
Vol 602-603 ◽  
pp. 438-442
Author(s):  
Lei Yu ◽  
Jian Yang ◽  
Tai Qiu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Bending Strength ◽  
Coefficient Of Thermal Expansion ◽  
Raw Materials ◽  
Linear Increase ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Uniform Microstructure

Fully dense (ZrB2+ZrC)/Zr3[Al (Si)]4C6 composites with ZrB2 content varying from 0 to 15 vol.% and fixed ZrC content of 10 vol.% were successfully prepared by in situ hot-pressing in Ar atmosphere using ZrH2, Al, Si, C and B4C as raw materials. With the increase of ZrB2 content, both the bending strength and fracture toughness of the composites increase and then decrease. The synergistic action of ZrB2 and ZrC as reinforcements shows significant strengthening and toughing effect to the Zr3[Al (Si)]4C6 matrix. The composite with 10 vol.% ZrB2 shows the optimal mechanical properties: 516 MPa for bending strength and 6.52 MPa·m1/2 for fracture toughness. With the increase of ZrB2 content, the Vickers hardness of the composites shows a near-linear increase from 15.3 GPa to 16.7 GPa. The strengthening and toughening effect can be ascribed to the unique mechanical properties of ZrB2 and ZrC reinforcements, the differences in coefficient of thermal expansion and modulus between them and Zr3[Al (Si)]4C6 matrix, fine grain strengthening and uniform microstructure derived by the in situ synthesis reaction.

scholarly journals The Mechanical Properties of AlSi17Cu5 Cast Alloy after Overheating and Modification of CuP Master Alloy

2013 ◽  
Vol 13 (3) ◽  
pp. 68-71
Author(s):  
J. Piątkowski ◽  
M. Jabłońska
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperature ◽  
Master Alloy ◽  
Liquid State ◽  
Alloy Composition ◽  
Cast Alloy ◽  
Primary Silicon ◽  
Grain Structure ◽  
Silicon Crystals ◽  
Fine Grain

Abstract The paper presents the results of studies on the effect of the AlSi17Cu5 alloy overheating to atemperature of 920°C and modification with phosphorus (CuP10) on the resultingmechanical (HB, Rm, R0.2) and plastic (A5 and Z) properties. It has been shown that, so-called, "timethermal treatment" (TTT) of an alloy in the liquid state, consisting inoverheating the metal to about 250°C above Tliq,holding at this temperature by 30 minutes improvesthe mechanical properties. It has also been found that overheating of alloy above Tliq.enhances the process of modification, resulting in the formation of fine-grain structure. The primary silicon crystals uniformly distributed in the eutectic and characteristics ofthe α(Al) solution supersaturated with alloying elements present in the starting alloy composition (Cu, Fe) provide not only an increase of strength at ambient temperature but also at elevated temperature (250°C).

Comprehensive Strengthening of Microalloyed Pure Gold

2015 ◽  
Vol 713-715 ◽  
pp. 2617-2623
Author(s):  
Jun Ping Yuan ◽  
Chun Yu Ma ◽  
Chang Wang
Keyword(s):  
Solid Solution ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Pure Gold ◽  
Solid Solution Strengthening ◽  
Fine Grain ◽  
Performance Requirements ◽  
Fine Grain Strengthening ◽  
Solution Strengthening ◽  
And Performance

The hardness of pure gold jewellery is low which makes it difficult to meet structural design and performance requirements, and restricts its artistic value. In this research, scandium, calcium, and magnesium were used as alloying elements with pure gold, and the microstructure and hardening behaviour of modified pure gold were studied through cold-working, solid solution, and aging treatment. The results showed that the as-cast hardness of an Sc-Ca-Mg alloyed pure gold could reach HV64: after solution treatment at 700 °C, the hardness could reach HV55, and the microstructure in its solid solution state presented a homogeneous single phase. When the modified pure gold was deformed and the deformation rate reached 80%, the hardness reached HV118, after aging treatment at 250 °C and small precipitation phases were dispersed in its structure; the resultant grain size was finer than that of pure gold, and the hardness reached HV133. The hardening behaviour of this modified pure gold was the comprehensive effect of solid solution strengthening, fine-grain strengthening, deformation strengthening, and precipitation strengthening.

Evolution of Microstructure and Mechanical Properties of the Thixo-Diecast 319s Alloy during Heat Treatment

2013 ◽  
Vol 765 ◽  
pp. 511-515 ◽  
Author(s):  
Da Quan Li ◽  
Xiao Kang Liang ◽  
Fu Bao Yang ◽  
You Feng He ◽  
Fan Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Cast Alloy ◽  
Grain Structure ◽  
Precipitate Size ◽  
Fine Grain ◽  
Microstructure And Mechanical Properties ◽  
Optimum Heat ◽  
Evolution Of Microstructure

The evolution of microstructure and mechanical properties during solution and ageing heat treatment process was studied in terms of a thixo-diecast impeller of 319s aluminium alloy. The cast alloy exhibited a microstructure consisting of primary uniformly distributed in α-Al globules and the eutectics. A series of heat treatment studies were performed to determine optimum heat treatment parameters, in order to achieve fine grain structure, fine silicon particles and optimal precipitate size and distribution. Optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to study the evolution of microstructure and mechanical properties. The results demonstrate that, the full T6 heat treatments are successfully applied to thixo-diecast 319s impellers. A two-step solution heat treatment is employed to prevent porosity due to overheating. The tensile properties of thixo-diecast 319s impellers were substantially enhanced after T6 heat treatment. The plate-shaped θ′ precipitates and lath-shaped Q′ precipitates are the most effective for precipitation strengthening.

Effect of Ca and Zr Additions and Aging Treatments on Microstructure and Mechanical Properties of Mg-Sn Alloy

2020 ◽  
Vol 993 ◽  
pp. 152-160
Author(s):  
Fan Wang ◽  
Yun Feng ◽  
Ming Shi Li ◽  
Xin Ying Teng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Brinell Hardness ◽  
Simple Substance ◽  
Maximum Tensile Strength ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Microstructure And Mechanical Properties ◽  
Brittle Phase ◽  
The Difference

The effect of Ca and Zr Additions and Aging Treatments on Microstructure and Mechanical Properties of Mg-Sn alloy was investigated. It was found that the grain size of as-cast Mg-4Sn-xCa and Mg-4Sn-xZr alloys was refined with the increase of alloying elements addition. The alloys were solution-treated at 480 °C and aged at 160 °C, and the aging peak appeared after 4-5 h. The difference was that the maximum tensile strength and Brinell hardness of Mg-4Sn-0.3Ca were 140.7 MPa and 44.5 HB, respectively, while in Mg-4Sn-xZr alloy, Mg-4Sn-0.5Zr was optimal. The maximum tensile strength and Brinell hardness of Mg-4Sn-0.5Zr were 137.4 MPa and 41.5 HB, respectively. This difference was mainly due to the formation of the brittle phase CaMgSn in the Mg-4Sn-xCa alloy. The excessive brittle phase was not conducive to the strength of the alloy, but could increase the hardness of the alloy. However, Zr existed as a simple substance in the alloy, which can be used as a nucleation particle to inhibit grain growth and play a role of fine grain strengthening. But the addition of Zr did not form many hard phases, so the hardness did not change much.

scholarly journals Effect of Nb on the Microstructure and Mechanical Properties of Ti2Cu Intermetallic through the First-Principle Calculations and Experimental Investigation

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 547 ◽  
Author(s):  
Jialin Cheng ◽  
Yeling Yun ◽  
Jingjing Wang ◽  
Jiaxin Rui ◽  
Shun Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
Density Functional ◽  
Covalent Bond ◽  
First Principle ◽  
Compression Tests ◽  
Solid Solution Strengthening ◽  
First Principle Calculations ◽  
Fine Grain ◽  
Fine Grain Strengthening

Through the first-principle calculations based on density functional theory and experimental investigation, the structural stability elastic properties and mechanical properties of Ti2Cu and Ti18Cu5Nb1 intermetallics were studied. The first-principle calculations showed that the ratio of bulk modulus to shear modulus (B/G) and Poisson’s ratio (ν) of Ti2Cu and Ti18Cu5Nb1 intermetallics were 2.03, 0.288, and 2.22, 0.304, respectively, indicating that the two intermetallics were ductile. This was confirmed by the compression tests, which showed that the plastic strain of both intermetallics was beyond 25%. In addition, the yield strength increased from the 416 to 710 MPa with the addition of Nb. The increase in strength is the result of three factors, namely covalent bond tendency, fine grain strengthening, and solid solution strengthening. This finding gives clues to design novel intermetallics with excellent mechanical properties by first-principle calculations and alloying.

scholarly journals Microstructure Evolution and Some Properties of Hard Magnetic FeCr30Co8 Alloy Subjected to Torsion Combined with Tension

Materials ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3019
Author(s):  
Anna Korneva ◽  
Galiya Korznikova ◽  
Rishat Kashaev ◽  
Boris Straumal
Keyword(s):  
Mechanical Properties ◽  
High Speed ◽  
Magnetic Alloy ◽  
Σ Phase ◽  
Fine Grain ◽  
Transmission Electron ◽  
Gradient Microstructure ◽  
Hard Magnetic Alloy ◽  
Short Annealing ◽  
Microscopy Techniques

The hard magnetic alloy FeCr30Co8 alloy was subjected to severe plastic deformation (SPD) by torsion combined with tension in the temperature range of 750 °C to 850 °C. This range of deformation temperatures corresponds to the α solid solution on the Fe–Cr–Co phase diagram. The study of the alloy after SPD by means of X-ray diffraction (XRD) and scanning and transmission electron microscopy techniques showed the formation of a gradient microstructure with fine grain size in the surface layer and precipitation of the hard intermetallic σ-phase. Next, the magnetic and mechanical properties of the deformed alloy after short annealing at 1000 °C and magnetic treatment were studied. A slight decrease in coercive force was found, along with a significant gain in plasticity and strength. The effective deformation temperature was determined to obtain the optimal magnetic and mechanical characteristics of the alloy. This method of deformation can be applied for the improvement of the mechanical properties of some magnets (high-speed rotors) which should have good magnetic properties within their volume while maintaining good mechanical properties on the surface.

Sign in / Sign up

Export Citation Format

Share Document