scholarly journals Composite Films of HDPE with SiO2 and ZrO2 Nanoparticles: The Structure and Interfacial Effects

Nanomaterials ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 2673
Author(s):  
Asif A. Nabiyev ◽  
Andrzej Olejniczak ◽  
Akhmed Kh. Islamov ◽  
Andrzej Pawlukojc ◽  
Oleksandr I. Ivankov ◽  
...  
Keyword(s):  
Interfacial Adhesion ◽  
Elevated Temperatures ◽  
Filler Content ◽  
Composite Films ◽  
Degree Of Crystallinity ◽  
Zro2 Nanoparticles ◽  
Interfacial Region ◽  
Lamellar Thickness ◽  
Sem Images ◽  
Crystallinity Degree

Herein, we investigated the influence of two types of nanoparticle fillers, i.e., amorphous SiO2 and crystalline ZrO2, on the structural properties of their nanocomposites with high-density polyethylene (HDPE). The composite films were prepared by melt-blending with a filler content that varied from 1% to 20% v/v. The composites were characterized by small- and wide-angle x-ray scattering (SAXS and WAXS), small-angle neutron scattering (SANS), Raman spectroscopy, differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). For both fillers, the nanoaggregates were evenly distributed in the polymer matrix and their initial state in the powders determined their surface roughness and fractal character. In the case of the nano-ZrO2 filler, the lamellar thickness and crystallinity degree remain unchanged over a broad range of filler concentrations. SANS and SEM investigation showed poor interfacial adhesion and the presence of voids in the interfacial region. Temperature-programmed SANS investigations showed that at elevated temperatures, these voids become filled due to the flipping motions of polymer chains. The effect was accompanied by a partial aggregation of the filler. For nano-SiO2 filler, the lamellar thickness and the degree of crystallinity increased with increasing the filler loading. SAXS measurements show that the ordering of the lamellae is disrupted even at a filler content of only a few percent. SEM images confirmed good interfacial adhesion and integrity of the SiO2/HDPE composite. This markedly different impact of both fillers on the composite structure is discussed in terms of nanoparticle surface properties and their affinity to the HDPE matrix.

scholarly journals Physicochemical, Mineralogical, and Mechanical Properties of Calcium Aluminate Cement Concrete Exposed to Elevated Temperatures

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3855
Author(s):  
Amirmohamad Abolhasani ◽  
Bijan Samali ◽  
Fatemeh Aslani
Keyword(s):  
Temperature Rise ◽  
Calcium Aluminate ◽  
Elevated Temperatures ◽  
Ultrasonic Pulse Velocity ◽  
Pulse Velocity ◽  
Calcium Aluminate Cement ◽  
Cement Concrete ◽  
Sem Images ◽  
Strength Deterioration ◽  
Aluminate Cement

One commonly used cement type for thermal applications is CAC containing 38–40% alumina, although the postheated behavior of this cement subjected to elevated temperature has not been studied yet. Here, through extensive experimentation, the postheated mineralogical and physicochemical features of calcium aluminate cement concrete (CACC) were examined via DTA/TGA, X-ray diffraction (XRD), and scanning electron microscopy (SEM) imaging and the variation in the concrete physical features and the compressive strength deterioration with temperature rise were examined through ultrasonic pulse velocity (UPV) values. In addition, other mechanical features that were addressed were the residual tensile strength and elastic modulus. According to the XRD test results, with the temperature rise, the dehydration of the C3AH6 structure occurred, which, in turn, led to the crystallization of the monocalcium dialuminate (CA2) and alumina (Al2O3) structures. The SEM images indicated specific variations in morphology that corresponded to concrete deterioration due to heat.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

scholarly journals Exploiting the Interplay between Liquid-Liquid Demixing and Crystallization of the PVDF Membrane for Membrane Distillation

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
N. I. M. Nawi ◽  
M. R. Bilad ◽  
N. A. H. M. Nordin ◽  
M. O. Mavukkandy ◽  
Z. A. Putra ◽  
...  
Keyword(s):  
Polyvinylidene Fluoride ◽  
Water Flux ◽  
High Water ◽  
Membrane Distillation ◽  
Degree Of Crystallinity ◽  
Solution Temperature ◽  
Hydrophobic Membrane ◽  
Sem Images ◽  
Cold Temperatures ◽  
Dope Solution

Membrane distillation (MD) purifies water by transporting its vapor through a hydrophobic membrane. An ideal MD membrane poses high water flux and high fouling, scaling, and wetting resistances. In this study, we develop polyvinylidene fluoride (PVDF) membranes for MD by focusing on reduction of PVDF degree of crystallinity. We explore the roles of dope solution temperature in dictating the phase separation mechanisms as well as the structure and the performance of semicrystalline PVDF membranes. DSC spectra show that higher dope solution temperature depresses crystallinity via formation of imperfect crystal. Such findings were also supported by FTIR and XRD results. The SEM images reveal formation of spherulite-like morphology in the membrane matrices for membranes prepared from high temperature dope solutions. A good balance between solid-liquid and liquid-liquid phase separations that offers low degree of crystallinity was found at a dope solution temperature of 60°C (PVDF-60), which showed the MD flux of 18 l/m2 h (vs. 6 l/m2 h for temperature of 25°C, as a benchmark) and nearly complete salt rejection when run at hot and cold temperatures of 65°C and 25°C, respectively. The PVDF-60 shows a high wetting resistance and stable MD flux of 10.5 l/m2 h over a 50 h test for treating brine solution as the feed (70 g NaCl/l).

Effects of the Different Crystallization Time on Synthesis of Zeolite 4A from by-Products of Polysilicon Production Process

2011 ◽  
Vol 347-353 ◽  
pp. 246-251
Author(s):  
Xing Yong Liu ◽  
Min Li ◽  
Hong Chen ◽  
Wei Wei
Keyword(s):  
Production Process ◽  
Degree Of Crystallinity ◽  
Crystallization Time ◽  
Crystallinity Degree ◽  
Structure Morphology ◽  
Zeolite 4A ◽  
Single Structure ◽  
Ft Ir ◽  
The Degree Of Crystallinity ◽  
By Products

Pure form,single phase and high crystalline zeolite 4A samples were synthesized during hydrothermal treatment of by-products in polysilicon production process. The effects of the different crystallization time on the degree of crystallinity, skeleton structure, morphology, size of the particle and its distribution of zeolite 4A samples were investigated using XRD,FT-IR,SEM and Zetasizer. The results indicated that the zeolite 4A sample featured high crystallinity degree, excellent dispersivity, high purity and single structure.

Residual Stress in Sputtered Silicon Oxycarbide Thin Films

2011 ◽  
Vol 1299 ◽  
Author(s):  
Ping Du ◽  
I-Kuan Lin ◽  
Yunfei Yan ◽  
Xin Zhang
Keyword(s):  
Thin Films ◽  
Residual Stress ◽  
Elevated Temperatures ◽  
Silicon Oxide ◽  
Composite Films ◽  
Deposition Process ◽  
Silicon Oxycarbide ◽  
X Ray ◽  
Curvature Measurement ◽  
Film Substrate

ABSTRACTSilicon carbide (SiC) has received increasing attention on the integration of microelectro-mechanical system (MEMS) due to its excellent mechanical and chemical stability at elevated temperatures. However, the deposition process of SiC thin films tends to induce relative large residual stress. In this work, the relative low stress material silicon oxide was added into SiC by RF magnetron co-sputtering to form silicon oxycarbide (SiOC) composite films. The composition of the films was characterized by Energy dispersive X-ray (EDX) analysis. The Young’s modulus and hardness of the films were measured by nanoindentation technique. The influence of oxygen/carbon ratio and rapid thermal annealing (RTA) temperature on the residual stress of the composite films was investigated by film-substrate curvature measurement using the Stoney’s equation. By choosing the appropriate composition and post processing, a film with relative low residual stress could be obtained.

scholarly journals Research on Mechanical Performance & Behaviour of Geopolymer Concrete Subjected to Elevated Temperatures

2019 ◽  
Vol 8 (2S8) ◽  
pp. 883-887
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Geopolymer Concrete ◽  
Sem Images ◽  
Before And After ◽  
Alkaline Conditions ◽  
Compressive Strength Of Concrete

The investigative studies on mechanical performance & behaviour, of Geopolymer Concrete (GPC) before and after the exposure to elevated temperatures (of 200 0 C -1000 0 C with an increment of 100 0 C). Indicate that the GPC Specimens Exhibited better Compressive strength at higher temperatures than that of those made by regular OPC Concrete with M30 Grade. The chronological changes in the geopolymeric structure upon exposure to these temperatures and their reflections on the thermal behaviour have also been explored. The SEM images indicate GPC produced by fly ash , metakaolin and silica fume, under alkaline conditions form Mineral binders that are not only non-flammable and but are also non-combustible resins and binders. Further the Observations drawn disclose that the mass and compressive strength of concrete gets reduced with increase in temperatures.

scholarly journals Effect of Filler Nature on Chemical Resistance and Microhardness of Epoxy Composite Films

2015 ◽  
Vol 16 (3) ◽  
pp. 528-533
Author(s):  
G. Martinyuk ◽  
O. Aksimentyeva ◽  
N. Skoreiko ◽  
V. Zakordonskyi
Keyword(s):  
Mechanical Properties ◽  
Chemical Resistance ◽  
Filler Content ◽  
Epoxy Composite ◽  
Composite Films ◽  
Physical And Mechanical Properties ◽  
Epoxy Composites ◽  
Mineral Filler ◽  
Operating Characteristics ◽  
Mineral Fillers

We investigated the processes of water absorption, chemical stability and microhardness of films of epoxy composites that contained as the polymer matrix the epoxy resin UP-655 and mineral fillers: graphite, mica, aluminum oxide at their content (0 - 30 % mass). It found that introduction of mineral fillers significantly affects on all complex of operating characteristics of the films. Increase of filler content, especially mica, to 20 %, resulting in slower process and reducing the quantity of absorbed moisture by films. In the study of physical and mechanical properties of filled epoxy composites was established that the introduction of mineral filler significantly affects their microhardness, and the nature of the exposure is determined by the type and filler content.

scholarly journals Role of Copper Oxide on Epoxy Coatings with New Intumescent Polymer-Based Fire Retardant

Molecules ◽  
2020 ◽  
Vol 25 (24) ◽  
pp. 5978
Author(s):  
Riyazuddin ◽  
Samrin Bano ◽  
Fohad Mabood Husain ◽  
Jamal Akhter Siddique ◽  
Khadijah H. Alharbi ◽  
...  
Keyword(s):  
Copper Oxide ◽  
Heat Release ◽  
Flame Retardant ◽  
Cone Calorimeter ◽  
Elevated Temperatures ◽  
Fire Retardant ◽  
Intumescent Flame Retardant ◽  
Gravimetric Analysis ◽  
Sem Images ◽  
Major Drawback

Epoxy resins (EP) have been used as a thermos-setting material in the field of coating, casting, bonding agent, and laminating. However, a major drawback associated with its use is the lack of good flaming properties, and it is responsible for heavy smoke along with hazardous gases considerably limiting its uses in various fields. In this study, N-ethanolamine triazine-piperizine, a melamine polymer (ETPMP), was established as a new charring-foaming agent and was successfully synthesized with ethanolamine, piperizine, cyanuric chloride, and melamine as precursor molecules via the nucleophilic substitution reaction method. Elemental analysis and Fourier transform infrared (FTIR) spectroscopy analysis were applied to approve the synthesis of ETPMP and confirmation of its structure and characterization. The epoxy coating of intumescent flame retardant (IFR) was equipped by introducing ETPMP, ammonium polyphosphate (APP), and copper oxide (CuO) in multiple composition ratios. CuO was loaded at various amounts into the IFR-coating system as a synergistic agent. The synergistic action of CuO on IFR coatings was scientifically examined by using different analytical tests such as vertical burning test (UL-94V), limited oxygen index (LOI), thermal gravimetric analysis (TGA), cone calorimeter, and scanning electron microscope (SEM). The results showed that small changes in the amount of CuO expressively amplified the LOI results and enhanced the V-0 ratings in the UL-94V test. The TGA data clearly demonstrate that the inclusion of CuO can transform the thermal deprivation behavior of coatings with a growing char slag proportion with elevated temperatures. Information from cone calorimeter data affirmed that CuO can decrease the burning factors by total heat release (THR) together with peak heat release rate (PHRR). The SEM images indicated that CuO can enrich the power and compression of the intumescent char that restricts the movement of heat and oxygen. Our results demonstrate a positive influence of CuO on the epoxy-headed intumescent flame retardant coatings.

scholarly journals Semi-Interpenetrating Polymer Networks Based on Cyanate Ester and Highly Soluble Thermoplastic Polyimide

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 862 ◽  
Author(s):  
Jingfeng Liu ◽  
Weifeng Fan ◽  
Gewu Lu ◽  
Defeng Zhou ◽  
Zhen Wang ◽  
...  
Keyword(s):  
High Performance ◽  
Elevated Temperatures ◽  
Polymer Networks ◽  
Gelation Time ◽  
Interpenetrating Polymer Networks ◽  
Step Method ◽  
Scanning Calorimetry ◽  
Sem Images ◽  
Biphenyltetracarboxylic Dianhydride ◽  
The Impact

Thermoplastic polyimide (TPI) was synthesized via a traditional one-step method using 2,3,3′,4′-biphenyltetracarboxylic dianhydride (3,4′-BPDA), 4,4′-oxydianiline (4,4′-ODA), and 2,2′-bis(trifluoromethyl)benzidine (TFMB) as the monomers. A series of semi-interpenetrating polymer networks (semi-IPNs) were produced by dissolving TPI in bisphenol A dicyanate (BADCy), followed by curing at elevated temperatures. The curing reactions of BADCy were accelerated by TPI in the blends, reflected by lower curing temperatures and shorter gelation time determined by differential scanning calorimetry (DSC) and rheological measurements. As evidenced by scanning electron microscopy (SEM) images, phase separation occurred and continuous TPI phases were formed in semi-IPNs with a TPI content of 15% and 20%. The properties of semi-IPNs were systematically investigated according to their glass transition temperatures (Tg), thermo-oxidative stability, and dielectric and mechanical properties. The results revealed that these semi-IPNs possessed improved mechanical and dielectric properties compared with pure polycyanurate. Notably, the impact strength of semi-IPNs was 47%–320% greater than that of polycyanurate. Meanwhile, semi-IPNs maintained comparable or even slightly higher thermal resistance in comparison with polycyanurate. The favorable processability and material properties make TPI/BADCy blends promising matrix resins for high-performance composites and adhesives.

scholarly journals Patterned Metal/Polymer Composite Film with Good Mechanical Stability and Repeatability for Flexible Electronic Devices Using Nanoimprint Technology

Micromachines ◽  
2019 ◽  
Vol 10 (10) ◽  
pp. 651
Author(s):  
Xu Zheng ◽  
Qing Wang ◽  
Jinjin Luan ◽  
Yao Li ◽  
Ning Wang
Keyword(s):  
Mechanical Properties ◽  
Composite Film ◽  
Polymer Composite ◽  
Interfacial Adhesion ◽  
Metal Film ◽  
Mechanical Stability ◽  
Electronic Devices ◽  
Composite Films ◽  
Polymer Composite Film ◽  
Metal Polymer

Mechanical stability and repeatability are significant factors for the application of metal film flexible electronic devices. In this work, patterned metal/polymer composite films with good mechanical stability and repeatability were fabricated through nanoimprint technology. The mechanical properties characteristic of metal/polymer composite films were exhibited by resistance change (ΔR/R0) after cyclic tension and bending loading. It was found that the ΔR/R0 and error line of patterned metal/polymer composite film was far lower than the other control groups for repeated experiments, which indicates that patterned metal film has excellent mechanical properties and repeatability. The double cantilever beam method was employed to measure the interfacial adhesion properties of composite films. The average interfacial adhesion of patterned metal/polymer composite films is shown to be over 2.9 and 2.2 times higher than that of metal film deposited on bare polymer and metal nanowire-treated polymer substrates, respectively.

Sign in / Sign up

Export Citation Format

Share Document