scholarly journals Effects of Micro-Braiding and Co-Wrapping Techniques on Characteristics of Flax/Polypropylene-Based Hybrid Yarn: A Comparative Study

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2559
Author(s):  
Wenqian Zhai ◽  
Peng Wang ◽  
Xavier Legrand ◽  
Damien Soulat ◽  
Manuela Ferreira
Keyword(s):  
Mechanical Characteristics ◽  
Tensile Tests ◽  
Strong Impact ◽  
Mass Ratio ◽  
Cover Factor ◽  
Hybrid Yarn ◽  
Before And After ◽  
Treatment Agent ◽  
Production Techniques ◽  
Yarn Production

Micro-braiding and co-wrapping techniques have been developed over a few decades and have made important contributions to biocomposites development. In this present study, a set of flax/polypropylene (PP) micro-braided and co-wrapped yarns was developed by varying different PP parameters (PP braiding angles and PP wrapping turns, respectively) to get different flax/PP mass ratios. The effects on textile and mechanical characteristics were studied thoroughly at the yarn scale, both dry- and thermo-state tensile tests were carried out, and tensile properties were compared before and after the braiding process to study the braidabilities. It was observed that PP braiding angles of micro-braided yarn influenced the frictional damage on surface treatment agent of flax roving, the cohesive effect between PP filaments/flax roving, and the PP cover factor; PP wrapping turns of co-wrapped yarn had a strong impact on the flax roving damage and the PP coverage, which further influenced the characteristics. Micro-braided yarn and co-wrapped yarn with the same flax/PP mass ratio were compared to evaluate the two different hybrid yarn production techniques; it was proven that micro-braided yarn presented better performance.

Development of a novel hybrid yarn production process for functional textile products

2018 ◽  
Vol 48 (9) ◽  
pp. 1462-1488 ◽  
Author(s):  
Nazife Korkmaz Memiş ◽  
Gizem Kayabaşı ◽  
Demet Yılmaz
Keyword(s):  
Tensile Properties ◽  
Fibre Bundle ◽  
Production Method ◽  
Textile Production ◽  
Hybrid Yarn ◽  
Spun Yarn ◽  
Spun Yarns ◽  
Production Techniques ◽  
Yarn Production ◽  
Textile Products

In this study, an innovative method consisting of electrospinning and conventional textile production techniques was built up to produce hybrid yarns enabling the production of functional textile products. The principle of the developed method is to open the twist of spun yarn, make this fibre bundle conductive for use as a collector, collect the electrospun nanofibres onto the conductive opened fibre bundle and finally twist this structure to produce hybrid yarn. To determine the feasibility of the developed method, surface morphology, chemical composition, coating features and tensile properties of the hybrid yarns were compared with that of the pure yarn and nanofibre-coated yarns produced without untwisting and retwisting processes. Test results demonstrated that untwisting process in hybrid production method provided the application of nanofibres interior structure of the spun yarn while retwisting process made integration of classical textile fibres and nanofibres together and hence locking the obtained yarn structure effectively. Thanks to the integrated structure, it was successful to get the yarn have the required tensile properties for weaving, knitting and other processes. Three minutes was determined as the optimum coating time for the effective nanofibre deposition and tensile properties. Summing up the results, it was believed that the method helps to benefit from the special properties of nanofibres for the functional yarn production together with durability and higher tensile properties of the spun yarns for larger usage areas. The presented findings could encourage the researchers to commercialize the method in order to get nanofibre-coated functional yarns.

scholarly journals Mimicking the Mechanical Properties of Aortic Tissue with Pattern-Embedded 3D Printing for a Realistic Phantom

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5042
Author(s):  
Jaeyoung Kwon ◽  
Junhyeok Ock ◽  
Namkug Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Aortic Wall ◽  
Tensile Tests ◽  
Human Aorta ◽  
Aortic Tissue ◽  
Medical Field ◽  
Base Materials

3D printing technology has been extensively applied in the medical field, but the ability to replicate tissues that experience significant loads and undergo substantial deformation, such as the aorta, remains elusive. Therefore, this study proposed a method to imitate the mechanical characteristics of the aortic wall by 3D printing embedded patterns and combining two materials with different physical properties. First, we determined the mechanical properties of the selected base materials (Agilus and Dragonskin 30) and pattern materials (VeroCyan and TPU 95A) and performed tensile testing. Three patterns were designed and embedded in printed Agilus–VeroCyan and Dragonskin 30–TPU 95A specimens. Tensile tests were then performed on the printed specimens, and the stress-strain curves were evaluated. The samples with one of the two tested orthotropic patterns exceeded the tensile strength and strain properties of a human aorta. Specifically, a tensile strength of 2.15 ± 0.15 MPa and strain at breaking of 3.18 ± 0.05 mm/mm were measured in the study; the human aorta is considered to have tensile strength and strain at breaking of 2.0–3.0 MPa and 2.0–2.3 mm/mm, respectively. These findings indicate the potential for developing more representative aortic phantoms based on the approach in this study.

scholarly journals Study of the Ultraviolet Effect and Thermal Analysis on Polypropylene Nonwoven Geotextile

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1080
Author(s):  
Clever Aparecido Valentin ◽  
Marcelo Kobelnik ◽  
Yara Barbosa Franco ◽  
Fernando Luiz Lavoie ◽  
Jefferson Lins da Silva ◽  
...  
Keyword(s):  
Uv Light ◽  
Polymeric Materials ◽  
Tensile Tests ◽  
Thermomechanical Analysis ◽  
Material Stiffness ◽  
Before And After ◽  
Electron Microscopy Analysis ◽  
Physical Tests ◽  
Nonwoven Geotextile

The use of polymeric materials such as geosynthetics in infrastructure works has been increasing over the last decades, as they bring down costs and provide long-term benefits. However, the aging of polymers raises the question of its long-term durability and for this reason researchers have been studying a sort of techniques to search for the required renewal time. This paper examined a commercial polypropylene (PP) nonwoven geotextile before and after 500 h and 1000 h exposure to ultraviolet (UV) light by performing laboratory accelerated ultraviolet-aging tests. The state of the polymeric material after UV exposure was studied through a wide set of tests, including mechanical and physical tests and thermoanalytical tests and scanning electron microscopy analysis. The calorimetric evaluations (DSC) showed distinct behaviors in sample melting points, attributed to the UV radiation effect on the aged samples. Furthermore, after exposure, the samples presented low thermal stability in the thermomechanical analysis (TMA), with a continuing decrease in their thicknesses. The tensile tests showed an increase in material stiffness after exposition. This study demonstrates that UV aging has effects on the properties of the polypropylene polymer.

Comparison between slag refining processes for B removal with metallurgical grade silicon and Si–Sn alloy

2018 ◽  
Vol 115 (3) ◽  
pp. 312 ◽  
Author(s):  
Rowaid Al-khazraji ◽  
Yaqiong Li ◽  
Lifeng Zhang
Keyword(s):  
Removal Efficiency ◽  
Acid Leaching ◽  
Experimental Results ◽  
Mass Ratio ◽  
Metallurgical Grade Silicon ◽  
Clear Effect ◽  
Slag Refining ◽  
Before And After ◽  
Grade Silicon ◽  
Refining Processes

Boron (B) removal by slag refining using CaO–SiO2–CaCl2 was investigated in metallurgical-grade silicon (MG-Si) and 75 wt% Si–Sn alloy. Experiments were conducted at 1500 °C for 15 min. The microstructure was characterized before and after refining. The effects of acid leaching, basicity, and slag/Si mass ratio on B removal were investigated. Experimental results showed that acid leaching had no effect on B removal from MG-Si but had a clear effect on the refined Si–Sn alloy after slag refining. The final B concentration was highly affected by the CaO/SiO2 mass ratio with minimum value, where the content of B was reduced from 18.36 ppmw to 5.5 ppmw at the CaO/SiO2 = 1.2 for MG-Si slag refining and from 18.36 ppmw to 3.7 ppmw at CaO/SiO2 = 1.5 for 75 wt% Si–Sn alloy. Increasing the slag mass ratio by 2:1 mass ratio also increased B removal efficiency by approximately 15–20% more than an increase by 1:1.

Comparative study of thermoplastic liner materials with regard to mechanical and permeation barrier properties before and after cyclic thermal aging

2021 ◽  
Vol 63 (4) ◽  
pp. 311-316
Author(s):  
Simon Backens ◽  
Jan Siering ◽  
Stefan Schmidt ◽  
Nikolai Glück ◽  
Wilko Flügge
Keyword(s):  
Thermal Aging ◽  
Barrier Properties ◽  
Tensile Tests ◽  
Polyamide 6 ◽  
Pressure Vessels ◽  
Cross Linking ◽  
Polyamide 12 ◽  
Type Iv ◽  
Before And After ◽  
Permeation Properties

Abstract Lightweight pressure vessels of type IV for hydrogen storage consist of a thermoplastic inner liner, commonly from polyethylene or polyamide. The liner is the permeation barrier against the compressed gas and must prevent the formation of cracks, also after temperature changes, for example after refueling processes. In the present work high-density polyethylene, cross-linked polyethylene, polyamide 6 and polyamide 12 were characterized by tensile tests, single notch impact tests and permeations measurements before and after a cyclic thermal aging process. The aging only lead to slight changes of mechanical properties due to post-crystallization, but to a significant decrease of permeation properties. This decrease was contributed to weakened, amorphous regions where chain splitting occurred. Considerable differences in properties resulted from different peroxide cross-linking times of polyethylene at the same temperature. A longer holding time at 200 °C led to an improvement in impact strength by a factor of more than three. However, the permeation properties decreased by about 50 %, indicating that peroxide cross-linking in the melt inhibited the formation of crystalline regions.

Mechanical and thermal behaviors of ultra-high molecular weight polyethylene triaxial braids: the influence of structural parameters

2018 ◽  
Vol 89 (16) ◽  
pp. 3362-3373 ◽  
Author(s):  
Shenglei Xiao ◽  
Charles Lanceron ◽  
Peng Wang ◽  
Damien Soulat ◽  
Hang Gao
Keyword(s):  
Molecular Weight ◽  
High Molecular Weight ◽  
Mechanical Characteristics ◽  
Structural Parameters ◽  
Tensile Tests ◽  
Tensile Behavior ◽  
Experimental Database ◽  
Strength And Deformation ◽  
Braiding Angle ◽  
Ultra High Molecular Weight

Recently, triaxial braids made from ultra-high molecular weight polyethylene (UHMWPE) have been recognized as one of the most popular composite reinforcements in the aerospace and defense fields. To further explore the mechanical characteristics of this material, a detailed experimental study on tensile behavior is reported in this paper. The triaxial braids show a “double-peak” phenomenon in tensile strength and deformation, caused by axial yarns and the in-plane shearing of bias yarns. The evolution of the braiding angle, measured during these tensile tests, is discussed according to the braiding parameters (initial braiding angle, number of axial yarns). Using the high conductivity properties of the UHMWPE material, the temperature caused by inter-yarn friction during tensile tests is also studied. This temperature is related to the evolution of the braiding angle. The temperature increases with the increasing number of axial yarns and decreases with increasing braiding angle. This study provides an experimental database on the influence of braiding parameters on the tensile behavior of triaxial braids.

scholarly journals Tensile Testing with Cyclic Strain Holding to Analyze Dynamic Recrystallization of Pure Lead

2014 ◽  
Vol 2014 ◽  
pp. 1-8
Author(s):  
Mayu Muramatsu ◽  
Motomichi Koyama ◽  
Ikumu Watanabe
Keyword(s):  
Dynamic Recrystallization ◽  
Tensile Testing ◽  
Cyclic Strain ◽  
Tensile Tests ◽  
Pure Lead ◽  
Factors Affecting ◽  
Before And After ◽  
Dynamic Recrystallization Behavior ◽  
The Difference ◽  
Strain Responses

We analyzed the dynamic recrystallization of pure lead by tensile testing with cyclic strain holding at room temperature. The specimens were held at an identical strain and subsequently reloaded, providing the strength before and after the strain holding process. The difference in strength enables factors affecting dynamic recrystallization behavior to be analyzed through mechanical testing. For instance, the effects of strain rate on dynamic recrystallization were analyzed by comparing the results obtained from tensile tests with and without strain holding. This experimental technique demonstrated some parts of contribution of elastic strain, dynamic recovery, dynamic recrystallization, and necking to stress-strain responses.

scholarly journals IMMOBILIZATION OF Saccharomycess cereviceae BIOMASS ON CHITOSAN AND ITS APPLICATION AS AN ADSORBENT FOR Pb(II) ION

2011 ◽  
Vol 11 (2) ◽  
pp. 174-179 ◽  
Author(s):  
Hasri Hasri ◽  
Mudasir Mudasir ◽  
Nurul Hidayat Aprilita ◽  
Roto Roto
Keyword(s):  
Optimum Condition ◽  
Functional Groups ◽  
Contact Time ◽  
Metal Ion ◽  
Mass Ratio ◽  
Adsorption Experiment ◽  
Ion Removal ◽  
Before And After ◽  
The Difference

An application of Saccharomycess cereviceae biomass immobilized on chitosan (SC-Chi adsorbent) for Pb(II) ion removal was demonstrated. Adsorption experiment was conducted at various mass ratio of Saccharomycess cereviceae biomass to chitosan, contact time, pH of solution and concentration of cation. Total Pb(II) metal ion adsorbed was calculated from the difference of the amount of metal ion before and after adsorption which was measured by AAS. The results showed that optimum condition for adsorption of Pb(II) ion by the SC-Chi was achieved using mass ratio of Saccharomycess cereviceae to chitosan of 50% (w/w), pH solution of 7, contact time of 60 min and concentration of 25 mgL-1. The hydroxyl (-OH) and amino (-NH2) functional groups are believed to be responsible for the adsorption of Pb(II) ion by the adsorbent.

scholarly journals MICROSTRUCTURE RESEARCH OF THE UNIDIRECTIONAL ORGANOPLASTIC BASED ON RUSAR-NT ARAMID FIBERS AND EPOXY-POLYSULFONE BINDER

2020 ◽  
pp. 19-26
Author(s):  
E.N. Kablov ◽  
◽  
G.S. Kulagina ◽  
G.F. Zhelezina ◽  
S.L. Lonskii ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Polymer Matrix ◽  
Packing Density ◽  
Tensile Tests ◽  
Polymer Composite Material ◽  
Aramid Fibers ◽  
Before And After ◽  
Binder Structure

This paper studies a polymer composite material - a unidirectional organoplastic based on Rusar-NT aramid fiber and a melt epoxy-polysulfone binder. Organoplastic has the following mechanical properties: tensile strength 2060 MPa, Young's modulus 101 GPa. The microstructure of the fiber and the polymer matrix in the organoplastic samples was studied before and after tensile tests. The features of the formation of the binder structure depending on the packing density of the fibers in organoplastics have been determined. The nature of the destruction of fibers and polymer matrix caused by the uniaxial tension has been studied.

SIMULATION OF DOOR MOVEMENT WITH A CLOSING MECHANISM

2021 ◽  
Vol 2021 (11) ◽  
pp. 4-10
Author(s):  
Aleksandr Reutov
Keyword(s):  
Mechanical Characteristics ◽  
Dynamic Models ◽  
Quality Criteria ◽  
Strong Impact ◽  
Closing Time ◽  
Door Opening ◽  
Air Resistance ◽  
The Moment ◽  
Moment Of Resistance ◽  
Closing Mechanism

The work objective is to determine the parameters of the closing mechanism that provide the specified characteristics of the door movement. Research method: computer simulation of the movement of a door with a lock mechanism as a multi-mass dynamic system, taking into account the mechanical characteristics and contact interaction of the lock mechanism. Research results and novelty. Computer dynamic models of a door with a door closer and a door with a spring have been developed. The moments of the door opening force, the closing time of the door, the angular velocity of the door at the time of impact with the frame are considered as the criteria for the quality of the door closing mechanism. Formulas are obtained that determine the permissible values of stiffness and deformation of the door closer spring according to the specified moments of the door opening force. The movement of doors with a door closer and with a spring is compared. The parameters of the closing mechanism providing the specified characteristics of the door movement of the considered example are determined. It is shown that with the same values of the opening force moments, the speed of impact with the frame in the case of the door closer is less than the door with a spring. Conclusions: The developed computer dynamic models of a door with a door closer and a door with a spring make it possible to determine the characteristics of the door movement taking into account the inertial and mechanical characteristics of the door closer and spring mechanisms. The permissible values of stiffness and deformation of the door closer spring can be determined by the specified moments of the door opening force in two positions. It is established that the forces of air resistance and friction in the hinges of the door cannot create the moment of resistance necessary for smooth closing of the door without a strong impact on the frame with a limited closing time. The quality criteria that minimize the closing time and the speed of impact of the door with the frame are contradictory. The choice of optimal parameters of the door closing mechanism is possible if one of the criteria is replaced by a restriction. The developed formulas and computer models are recommended for use in the design of devices that restrict the movement of doors.

Sign in / Sign up

Export Citation Format

Share Document