scholarly journals Viscoelastic Behavior of Drug-Loaded Polyurethane

Polymers ◽  
2021 ◽  
Vol 13 (16) ◽  
pp. 2608
Author(s):  
Navideh Abbasnezhad ◽  
Mohammadali Shirinbayan ◽  
Fatiha Chabi ◽  
Stephane Champmartin ◽  
Abbas Tcharkhtchi ◽  
...  
Keyword(s):  
Physicochemical Properties ◽  
Volume Fraction ◽  
Viscoelastic Behavior ◽  
Drug Carriers ◽  
Tensile Tests ◽  
Release Time ◽  
Fluid Medium ◽  
Free Volume Fraction ◽  
Drug Eluting ◽  
Loading Ratio

Drug-eluting stents are desirable platforms for local medicine delivery. However, the incorporation of drugs into polymers can influence the mechanical and physicochemical properties of said matrix, which is a topic that is still poorly understood. In fact, this is more noticeable since the apposition is most often accompanied by mechanical stresses on the polymer coating, which can induce therapeutic failure that can result in death. It is therefore necessary to better understand their behavior by examining their properties in conditions such as those in living beings. We studied polyurethane drug carriers made in-house. Diclofenac epolamine was chosen as a model hydrophilic medicine. We used thermal measurements (DMTA) and tensile tests. The aim was to establish the influence of the loading and release of the drug on the physicochemical properties of this polymer in the presence of a stagnant or circulating fluid medium, phosphate-buffered saline (PBS). For the two PU/drug loadings studied, the effect of the initial drug load was more marked. The free volume fraction and the number of pores in the samples increased with the increasing percent of the drug and with release time. The kinetic profiles were accelerated with the loading ratio and with the presence of flow. Young′s modulus and ultimate stress were not significantly influenced by the release time. A relevant relationship between the tensile properties and the viscoelastic behavior of the samples was developed. Our results have implications for optimizing the performance of drug coatings for stents.

scholarly journals Low-carbon cast microalloyed steel intercritically heat-treated at different temperatures: microstructure and mechanical properties

2021 ◽  
Vol 21 (2) ◽  
Author(s):  
Hadi Torkamani ◽  
Shahram Raygan ◽  
Carlos Garcia Mateo ◽  
Yahya Palizdar ◽  
Jafar Rassizadehghani ◽  
...  
Keyword(s):  
Carbon Content ◽  
Volume Fraction ◽  
Block Size ◽  
Tensile Tests ◽  
Total Elongation ◽  
Martensite Phase ◽  
Low Carbon ◽  
Steel Increase ◽  
Different Temperatures ◽  
The Impact

AbstractIn this study, dual-phase (DP, ferrite + martensite) microstructures were obtained by performing intercritical heat treatments (IHT) at 750 and 800 °C followed by quenching. Decreasing the IHT temperature from 800 to 750 °C leads to: (i) a decrease in the volume fraction of austenite (martensite after quenching) from 0.68 to 0.36; (ii) ~ 100 °C decrease in martensite start temperature (Ms), mainly due to the higher carbon content of austenite and its smaller grains at 750 °C; (iii) a reduction in the block size of martensite from 1.9 to 1.2 μm as measured by EBSD. Having a higher carbon content and a finer block size, the localized microhardness of martensite islands increases from 380 HV (800 °C) to 504 HV (750 °C). Moreover, despite the different volume fractions of martensite obtained in DP microstructures, the hardness of the steels remained unchanged by changing the IHT temperature (~ 234 to 238 HV). Applying lower IHT temperature (lower fraction of martensite), the impact energy even decreased from 12 to 9 J due to the brittleness of the martensite phase. The results of the tensile tests indicate that by increasing the IHT temperature, the yield and ultimate tensile strengths of the DP steel increase from 493 to 770 MPa, and from 908 to 1080 MPa, respectively, while the total elongation decreases from 9.8 to 4.5%. In contrast to the normalized sample, formation of martensite in the DP steels could eliminate the yield point phenomenon in the tensile curves, as it generates free dislocations in adjacent ferrite.

scholarly journals Effect of Terminal Groups on Thermomechanical and Dielectric Properties of Silica–Epoxy Composite Modified by Hyperbranched Polyester

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2451
Author(s):  
Jianwen Zhang ◽  
Dongwei Wang ◽  
Lujia Wang ◽  
Wanwan Zuo ◽  
Lijun Zhou ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Binding Energy ◽  
Epoxy Resin ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
Mean Square Displacement ◽  
Mean Square ◽  
Hyperbranched Polyester ◽  
Free Volume Fraction

To study the effect of hyperbranched polyester with different kinds of terminal groups on the thermomechanical and dielectric properties of silica–epoxy resin composite, a molecular dynamics simulation method was utilized. Pure epoxy resin and four groups of silica–epoxy resin composites were established, where the silica surface was hydrogenated, grafted with silane coupling agents, and grafted with hyperbranched polyester with terminal carboxyl and terminal hydroxyl, respectively. Then the thermal conductivity, glass transition temperature, elastic modulus, dielectric constant, free volume fraction, mean square displacement, hydrogen bonds, and binding energy of the five models were calculated. The results showed that the hyperbranched polyester significantly improved the thermomechanical and dielectric properties of the silica–epoxy composites compared with other surface treatments, and the terminal groups had an obvious effect on the enhancement effect. Among them, epoxy composite modified by the hyperbranched polyester with terminal carboxy exhibited the best thermomechanical properties and lowest dielectric constant. Our analysis of the microstructure found that the two systems grafted with hyperbranched polyester had a smaller free volume fraction (FFV) and mean square displacement (MSD), and the larger number of hydrogen bonds and greater binding energy, indicating that weaker strength of molecular segments motion and stronger interfacial bonding between silica and epoxy resin matrix were the reasons for the enhancement of the thermomechanical and dielectric properties.

scholarly journals Shape and Temperature Expansion of Free Volume Holes in Some Cured Polybutadiene-Polyisoprene Rubber Blends

2021 ◽  
Vol 22 (3) ◽  
pp. 1436
Author(s):  
Giovanni Consolati ◽  
Eros Mossini ◽  
Dario Nichetti ◽  
Fiorenza Quasso ◽  
Giuseppe Maria Viola ◽  
...  
Keyword(s):  
Free Volume ◽  
Radial Direction ◽  
Volume Fraction ◽  
Spherical Shape ◽  
Suitable Model ◽  
Positron Annihilation Lifetime ◽  
Rubber Blends ◽  
Free Volume Fraction ◽  
Hole Model ◽  
Best Fit

The free volume fraction of a macromolecular structure can be assessed theoretically by using a suitable model; however, it can also be evaluated from experimental data obtained from dilatometry and positron annihilation lifetime spectra. In this second case, a regular geometry of the sub-nanometric cavities forming the free volume has to be assumed, although in fact they are irregularly shaped. The most popular approach is to guess spherical holes, which implies an isotropic growth of these last with temperature. In this work, we compared the free volume fraction, as obtained from experiments in a set of polybutadiene and polyisoprene cured rubbers and their blends, with the analogous quantity expected by using the lattice-hole model. The results allowed us to obtain insights on the approximate shape of the holes. Indeed, a cylindrical flattened geometry of the cavities produced a better agreement with the theory than the spherical shape. Furthermore, the best fit was obtained for holes that expanded preferentially in the radial direction, with a consequent decrease of the aspect ratio with temperature.

scholarly journals Mechanical Properties and Microstructural Aspects of Two High-Manganese Steels with TWIP/TRIP Effects: A Comparative Study

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 24
Author(s):  
Matías Bordone ◽  
Juan Perez-Ipiña ◽  
Raúl Bolmaro ◽  
Alfredo Artigas ◽  
Alberto Monsalve
Keyword(s):  
Mechanical Response ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Chemical Compositions ◽  
High Manganese ◽  
Microstructural Changes ◽  
Ε Martensite ◽  
High Manganese Steels ◽  
Manganese Steels

This article is focused on the mechanical behavior and its relationship with the microstructural changes observed in two high-manganese steels presenting twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP), namely Steel B and Steel C, respectively. Chemical compositions were similar in manganese, but carbon content of Steel B approximately doubles Steel C, which directly impacted on the stacking fault energy (SFE), microstructure and mechanical response of each alloy. Characterization of as-cast condition by optical microscope revealed a fully austenitic microstructure in Steel B and a mixed microstructure in Steel C consisting of austenite grains and thermal-induced (εt) martensite platelets. Same phases were observed after the thermo-mechanical treatment and tensile tests, corroborated by means of X-Ray Diffraction (XRD), which confirms no phase transformation in Steel B and TRIP effect in Steel C, due to the strain-induced γFCC→εHCP transformation that results in an increase in the ε-martensite volume fraction. Higher values of ultimate tensile strength, yield stress, ductility and impact toughness were obtained for Steel B. Significant microstructural changes were revealed in tensile specimens as a consequence of the operating hardening mechanisms. Scanning Electron Microscopy (SEM) observations on the tensile and impact test specimens showed differences in fracture micro-mechanisms.

Shape Memory Characteristics and Superelasticity of Ti-Ni-Cu Alloy Ribbons with Nano Ti2Ni Particles

2008 ◽  
Vol 8 (2) ◽  
pp. 722-727 ◽  
Author(s):  
Tae-hyun Nam ◽  
Cheol-am Yu ◽  
Jung-min Nam ◽  
Hyun-gon Kim ◽  
Yeon-wook Kim
Keyword(s):  
Melt Spinning ◽  
Volume Fraction ◽  
Deformation Behaviour ◽  
Parent Phase ◽  
Tensile Tests ◽  
Constant Load ◽  
Cu Alloy ◽  
Transmission Electron ◽  
Average Size ◽  
Memory Characteristics

Microstructures and deformation behaviour of Ti-45Ni-5Cu and Ti-46Ni-5Cu alloy ribbons prepared by melt spinning were investigated by transmission electron microscopy, thermal cycling tests under constant load and tensile tests. Spherical Ti2Ni particles coherent with the B2 parent phase were observed in the alloy ribbons when the melt spinning temperature was higher than 1773 K. Average size of Ti2Ni particles in the ribbons obtained at 1873 K was 8 nm, which was smaller than that (10 nm) in the ribbons obtained at 1773 K. Volume fraction of Ti2Ni phase in the ribbons obtained at 1873 K was 40%, which was larger than that (20%) in the ribbons obtained at 1773 K. The stress required at temperatures of Af + 10 K for the stress-induced martensitic transformation increased from 93 MPa to 229 MPa and apparent elastic modulus of the B2 parent phase increased from 56 GPa to 250 GPa with increasing the melt spinning temperature from 1673 K to 1873 K in Ti-45Ni-5Cu alloy ribbons. The critical stress for slip deformation of the ribbons increased by coherent Ti2Ni particles, and thus residual elongation did not occur even at 160 MPa, while considerable plastic deformation occurred at 60 MPa in the ribbons without Ti2Ni particles. Almost perfect superelastic recovery was found in the ribbons with coherent Ti2Ni particles, while only partial superelastic recovery was observed in the ribbons without coherent Ti2Ni particles.

Spark Plasma Sintering of Ti-4.5Al-3V-2Fe-2Mo (SP-700)

2010 ◽  
Vol 654-656 ◽  
pp. 819-822
Author(s):  
Genki Kikuchi ◽  
Hiroshi Izui ◽  
Yuya Takahashi ◽  
Shota Fujino
Keyword(s):  
Spark Plasma Sintering ◽  
Room Temperature ◽  
Volume Fraction ◽  
Titanium Boride ◽  
Tensile Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Tib2 Particles

In this study, we focused on the sintering performance of Ti-4.5Al-3V-2Mo-2Fe (SP-700) and mechanical properties of SP-700 reinforced with titanium boride (TiB/SP-700) fabricated by spark plasma sintering (SPS). TiB whiskers formed in titanium by a solid-state reaction of titanium and TiB2 particles were analyzed with scanning electron microscopy and X-ray diffraction. The TiB/SP-700 was sintered at temperatures of 1073, 1173, and 1273 K and a pressure of 70 MPa for 10, 30, and 50 min. The volume fraction of TiB ranged from 1.7 vol.% to 19.9 vol.%. Tensile tests of TiB/SP-700 were conducted at room temperature, and the effect of TiB volume fraction on the tensile properties was investigated.

Cellulose Whiskers Micro-Fibers Effect in the Mechanical Proprieties of PP and PLA Composites Fibers Obtained by Spinning Process

2011 ◽  
Vol 146 ◽  
pp. 12-26 ◽  
Author(s):  
A. Gherissi ◽  
R.Ben Cheikh ◽  
E. Dévaux ◽  
Fethi Abbassi
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Tensile Tests ◽  
Advanced Materials ◽  
Uniaxial Tensile ◽  
Failure Resistance ◽  
Cellulose Whiskers ◽  
Limit Strength

In this study, we present the manufacturing process of two new composites materials in the form of long fibers of polylactic-acid (PLA) or polypropylene (PP), reinforced by cellulose whiskers micro-fibers loads. In order to evaluate the mechanical properties of these advanced materials, a several uniaxial tensile tests were carried out. The PP and the PLA have initially been spinning without the addition of cellulose whiskers micro-fibers. In order to study the effects of cellulose whiskers micro-fibers reinforcements in the Mechanical behavior of the PLA and PP filaments, we determinate the proprieties of these advanced material from the tensile results. For the PP composite filaments material case, the whiskers reinforcement increases Young's modulus and failure resistance, but it reduces the limit strength failure. For the PLA composites the addition of 1% wt of cellulose whiskers from the total volume fraction of the material, increase the Young’s modulus more than 50% and a decrease of the failure resistance and the limit strength of composite. The obtained composites fibers are very rigid and brittle. What follows, that the addition of cellulose whiskers micro fibers in PP matrix, provides mechanical properties more convenient compared to the PLA matrix.

Strain Rate Effects on Tensile Properties of Fiber Reinforced Concrete

1985 ◽  
Vol 64 ◽  
Author(s):  
George G. Nammur ◽  
Antoine E. Naaman
Keyword(s):  
Reinforced Concrete ◽  
Strain Rate ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Strain Rate Effects ◽  
Rate Effects ◽  
The Matrix

ABSTRACTHigh strain rates lead to substantial modifications in the stress-strain (or stress-displacement) response of fiber reinforced concrete in tension. These modifications include higher strength and corresponding strain, as well as smaller displacement at failure.The purpose of this paper is to investigate the behavior of fiber reinforced concrete under impact tensile loading, and to study the effect of strain rate on the post-cracking strength of the composite. The variation of the tensile strength of the matrix with the reinforcement parameters such as volume fraction Vf and aspect ratio |/φ of the fibers is also studied ip this paper. A special emphasis is placed on the stress-displacement relationship of steel fiber reinforced concrete in its post-cracking range. An empirical model of the stress- displacement relationship as a function of the strain rate is developed from experimental data from tensile tests on dogbone shape notched tensile prisms. The model highlights the effects of strain rate and fiber properties on the post-cracking strength of the composite, as well as the displacement at failure. The effect of strain rate on the post-cracking toughness of fiber reinforced concrete is also addressed. The literature on impact effects on concrete in tension (plain and fiber reinforced) is briefly reviewed in this paper, and so is the state of the art of testing techniques for strain rate effects.

An Analytical and Experimental Study of Strength and Failure Behavior of Plain Weave Composites

1998 ◽  
Vol 32 (1) ◽  
pp. 2-30 ◽  
Author(s):  
Makoto Ito ◽  
Tsu-Wei Chou
Keyword(s):  
Volume Fraction ◽  
Random Phase ◽  
Three Dimensional ◽  
Tensile Tests ◽  
Packing Fraction ◽  
Failure Behavior ◽  
Fiber Volume ◽  
Laminate Composites ◽  
Plain Weave ◽  
Geometrical Characteristics

This paper analyzes the strengxth and failure behavior of plain weave composites. First, the geometrical characteristics of yarn shape, laminate stacking configuration, fiber volume fraction, and yarn packing fraction are investigated using three-dimensional geometrical models. Based on the geometrical characteristics, iso-strain approach is developed to predict elastic properties, stress distributions, and strengths under tensile loading. The laminate stacking configuration and fabric waviness ratio have significant influence on the composite failure behavior. Specimens of iso-phase, out-of-phase and random-phase laminate composites are prepared. The mathematical models developed are evaluated by microscopic observation and tensile tests.

Viscoelastic behavior of epoxy resin reinforced with shape-memory-alloy wires

2020 ◽  
pp. 1045389X2097549
Author(s):  
Niloufar Bagheri ◽  
Mahmood M Shokrieh ◽  
Ali Saeedi
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Epoxy Resin ◽  
Volume Fraction ◽  
Niti Alloy ◽  
Micromechanical Model ◽  
Viscoelastic Behavior ◽  
Mechanical Analysis ◽  
Reinforced Polymer ◽  
Small Volume Fraction

The effect of NiTi alloy long wires on the viscoelastic behavior of epoxy resin was investigated by utilizing the dynamic mechanical analysis (DMA) and a novel micromechanical model. The present model is capable of predicting the viscoelastic properties of the shape-memory-alloy (SMA) reinforced polymer as a function of the SMA volume fraction, initial martensite volume fraction, pre-strain level in wires, and the temperature variations. The model was verified by conducting experiments. Good agreement between the theoretical and experimental results was achieved. A parametric study was also performed to investigate the effect of SMA parameters. According to the results, by the addition of a small volume fraction of SMA, the storage modulus of the composite increases significantly, especially at higher temperatures. Moreover, applying a 4% pre-strain caused a 10% increase in the maximum value of the loss factor of the SMA reinforced epoxy in comparison with the 0% pre-strained SMA reinforced epoxy.

Sign in / Sign up

Export Citation Format

Share Document