scholarly journals A Novel GBSM for Non-Stationary V2V Channels Allowing 3D Velocity Variations

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3271
Author(s):  
Naeem Ahmed ◽  
Boyu Hua ◽  
Qiuming Zhu ◽  
Kai Mao ◽  
Junwei Bao
Keyword(s):  
Communication Systems ◽  
Three Dimensional ◽  
Path Delay ◽  
Angle Of Arrival ◽  
Channel Coefficient ◽  
Auto Correlation Function ◽  
Velocity Variations ◽  
V2v Communications ◽  
Doppler Power ◽  
Von Mises

A new non-stationary (NS) geometry-based stochastic model (GBSM) is presented for developing and testing the communication systems of vehicle-to-vehicle (V2V) applications, which considers the three-dimensional (3D) scattering environments and allows 3D velocity as well. In this paper, the proposed GBSM for NS V2V channels allowed 3D velocity variations and was more suitable for actual V2V communications because it provided smoother transitions between the consecutive channel segments. The time-variant channel coefficient and the channel parameters, i.e., Doppler frequencies, path delay and power, angle of arrival (AoA), and angle of departure (AoD), were analyzed and derived. Likewise, the theoretical statistical properties as the probability density function (PDF), the auto-correlation function (ACF), and Doppler power spectral density (DPSD) were also analyzed and derived under the von Mises–Fisher (VMF) distribution. Finally, the theoretical and measured results were well coordinated alongside the implemented results, which confirmed the feasibility of the introduced model along with the theoretical expressions.

scholarly journals Analytical Non-Stationary Satellite to Aircraft Channel Modeling over Open Area Based on Regular Shaped Geometry-Based Stochastic Model

2020 ◽  
Vol 10 (15) ◽  
pp. 5041
Author(s):  
Zaixue Wei ◽  
Qipeng Tang ◽  
Jian Geng ◽  
Sibo Chen ◽  
Lin Sang ◽  
...  
Keyword(s):  
Stochastic Model ◽  
Communication Systems ◽  
Satellite Communication ◽  
Channel Model ◽  
Transfer Functions ◽  
Specular Reflection ◽  
Channel Modeling ◽  
Path Model ◽  
Path Delay ◽  
Doppler Power

Channel modeling is crucial to the development and evaluation of modern wireless communication systems including satellite communication system, since there might be critical safty-of-life applications. Also, the channel model is of great importance to the performance evaluation of mobile communication systems. In recent years, encouraged by the widely application of unmanned aerial vehicles, the research on channel modeling for aerial and aeronautical communications attract lots of interests. In the published articles, stationary and non-stationary channel models have been developed for air-to-ground communications based on regular shaped geometry-based stochastic model (RS-GBSM). The modeling of air-to-air or satellite-to-aircraft (S2A) communication is still quite simple or completely lacking. For obtaining more precise model of S2A channel, this paper presents an analytical non-stationary S2A channel mode based on RS-GBSM with considerations on line-of-sight path, specular reflection path, and ground scattering path. Analytical expressions of the channel impulse responses, the transfer functions, the auto-correlation functions, and the Doppler power spectrum density based on 3-path model are derived and simulated. Also, the distributions of the path antennation, the path delay, and the normalized Doppler shift based on uniform distribution of the scatterers are derived, simulated and fitted.

scholarly journals A Novel 3D Nonstationary Channel Model Based on the von Mises-Fisher Scattering Distribution

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
Yuming Bi ◽  
Jianhua Zhang ◽  
Ming Zeng ◽  
Mengmeng Liu ◽  
Xiaodong Xu
Keyword(s):  
Fourier Transform ◽  
High Speed ◽  
Channel Model ◽  
Elevation Angle ◽  
Three Dimensional ◽  
Azimuth Angle ◽  
Angle Of Arrival ◽  
Mean Values ◽  
Physical Channel ◽  
Von Mises

In the last decade, the nonstationary properties of channel models have attracted more and more attention for many scenarios, that is, vehicle-to-vehicle (V2V), mobile-to-mobile (M2M), and high-speed train (HST). However, little research has been done on the real-physical channel model. In this paper, we propose a generalized three-dimensional (3D) nonstationary channel model, in which the scatterers are assumed to be distributed around the transmitter (Tx) and receiver (Rx) on a two-sphere model. By employing the von Mises-Fisher distribution, the mean values of the azimuth angle of departure (AAoD) and elevation angle of departure (EAoD) and the azimuth angle of arrival (AAoA) and elevation angle of arrival (EAoA) are tracked by time-variant (TV) Brownian Markov (BM) motion paths, which ensure the nonstationarity of the proposed channel model. Moreover, the TV autocorrelation function (ACF) and Doppler power spectrum density (DPSD) of the proposed nonstationary channel model are calculated by using signal processing tools, for example, fast Fourier transform (FFT) and short-time Fourier transform (STFT). In addition, the simulation results show that the TV scatterer distribution results in a nonstationary nonisotropic channel model, and the proposed model can be employed to simulate the 3D nonstationary channel model.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

scholarly journals Full snapshot reconstruction in hybrid architecture antenna arrays

2020 ◽  
Vol 2020 (1) ◽  
Author(s):  
Maria Trigka ◽  
Christos Mavrokefalidis ◽  
Kostas Berberidis
Keyword(s):  
Antenna Array ◽  
Antenna Arrays ◽  
Communication Systems ◽  
Linear Array ◽  
Research Work ◽  
Hybrid Architecture ◽  
Angle Of Arrival ◽  
Music Algorithm ◽  
Array Structures ◽  
Signal Sources

AbstractIn the context of this research work, we study the so-called problem of full snapshot reconstruction in hybrid antenna array structures that are utilized in mmWave communication systems. It enables the recovery of the snapshots that would have been obtained if a conventional (non-hybrid) uniform linear antenna array was employed. The problem is considered at the receiver side where the hybrid architecture exploits in a novel way the antenna elements of a uniform linear array. To this end, the recommended scheme is properly designed so as to be applicable to overlapping and non-overlapping architectures. Moreover, the full snapshot recoverability is addressed for two cases, namely for time-varying and constant signal sources. Simulation results are also presented to illustrate the consistency between the theoretically predicted behaviors and the simulated results, and the performance of the proposed scheme in terms angle-of-arrival estimation, when compared to the conventional MUSIC algorithm and a recently proposed hybrid version of MUSIC (H-MUSIC).

scholarly journals Effects of intracorneal ring segments implementation technique and design on corneal biomechanics and keratometry in a personalized computational analysis

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Niksa Mohammadi Bagheri ◽  
Mahmoud Kadkhodaei ◽  
Shiva Pirhadi ◽  
Peiman Mosaddegh
Keyword(s):  
Clinical Data ◽  
Three Dimensional ◽  
Element Model ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Average Error ◽  
Constant Thickness ◽  
Arc Length ◽  
Implementation Techniques ◽  
Von Mises

AbstractThe implementation of intracorneal ring segments (ICRS) is one of the successfully applied refractive operations for the treatment of keratoconus (kc) progression. The different selection of ICRS types along with the surgical implementation techniques can significantly affect surgical outcomes. Thus, this study aimed to investigate the influence of ICRS implementation techniques and design on the postoperative biomechanical state and keratometry results. The clinical data of three patients with different stages and patterns of keratoconus were assessed to develop a three-dimensional (3D) patient-specific finite-element model (FEM) of the keratoconic cornea. For each patient, the exact surgery procedure definitions were interpreted in the step-by-step FEM. Then, seven surgical scenarios, including different ICRS designs (complete and incomplete segment), with two surgical implementation methods (tunnel incision and lamellar pocket cut), were simulated. The pre- and postoperative predicted results of FEM were validated with the corresponding clinical data. For the pre- and postoperative results, the average error of 0.4% and 3.7% for the mean keratometry value ($$\text {K}_{\text{mean}}$$ K mean ) were predicted. Furthermore, the difference in induced flattening effects was negligible for three ICRS types (KeraRing segment with arc-length of 355, 320, and two separate 160) of equal thickness. In contrast, the single and double progressive thickness of KeraRing 160 caused a significantly lower flattening effect compared to the same type with constant thickness. The observations indicated that the greater the segment thickness and arc-length, the lower the induced mean keratometry values. While the application of the tunnel incision method resulted in a lower $$\text {K}_{\text{mean}}$$ K mean value for moderate and advanced KC, the induced maximum Von Mises stress on the postoperative cornea exceeded the induced maximum stress on the cornea more than two to five times compared to the pocket incision and the preoperative state of the cornea. In particular, an asymmetric regional Von Mises stress on the corneal surface was generated with a progressive ICRS thickness. These findings could be an early biomechanical sign for a later corneal instability and ICRS migration. The developed methodology provided a platform to personalize ICRS refractive surgery with regard to the patient’s keratoconus stage in order to facilitate the efficiency and biomechanical stability of the surgery.

Mechanics of Composite Layered Rough Medium in Contact

2013 ◽  
Vol 703 ◽  
pp. 200-203
Author(s):  
Shao Biao Cai ◽  
Yong Li Zhao
Keyword(s):  
Material Properties ◽  
Three Dimensional ◽  
Shear Stresses ◽  
Normal Loading ◽  
Layered Coatings ◽  
Pressure Profiles ◽  
Tangential Traction ◽  
Von Mises ◽  
Von Mises Stresses ◽  
Tangential Friction

This study presents a first attempt to develop a numerical three-dimensional multilayered (more than 2 composite layered coatings) elasticperfectly plastic rough solids model to investigate the contact behavior under combined normal loading and tangential traction. Contact analyses are performed to study the effects composite thin film layers. Local contact pressure profiles, von Mises stresses, and shear stresses as a function of material properties and applied normal and tangential friction loads are calculated.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

scholarly journals Elasto-plastic analysis of the contact region between a rigid ellipsoid and a semi-flat surface

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401879739 ◽  
Author(s):  
Pengyang Li ◽  
Lingxia Zhou ◽  
Fangyuan Cui ◽  
Quandai Wang ◽  
Meiling Guo ◽  
...  
Keyword(s):  
Residual Stress ◽  
Plastic Deformation ◽  
Plastic Strain ◽  
Contact Pressure ◽  
Contact Region ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Effective Plastic Strain ◽  
Normal Forces ◽  
Von Mises

When the load acting on a mechanical structure is greater than the yield strength of the material, the contact surface will undergo plastic deformation. Cumulative plastic deformation has an important influence on the lifespan of mechanical parts. This article presents a three-dimensional semi-analytical model based on the conjugate gradient method and fast Fourier transform algorithm, with the aim of studying the characteristic parameters of the contact region between a rigid ellipsoid and elasto-plastic half-space. Moreover, normal forces and tangential traction were considered, as well as the contact pressure resulting from various sliding speeds and friction coefficients. The contact pressure, effective plastic strain, von Mises stress, and residual stress were measured and shown to increase with increasing sliding velocity. Finally, when the friction coefficient, contact pressure, and effective plastic strain are increased, the von Mises stress is also shown to increase, whereas the residual stress decreases.

Failure Analysis of Cementless Hip Joint Prosthesis

2013 ◽  
Vol 845 ◽  
pp. 403-407
Author(s):  
Natesan Dhandapani ◽  
A. Gnanavelbabu ◽  
M. Sivasankar
Keyword(s):  
Hip Joint ◽  
Low Cost ◽  
Three Dimensional ◽  
Surface Characteristics ◽  
Element Model ◽  
Von Mises Stress ◽  
Surface Model ◽  
Joint Prosthesis ◽  
Replacement Technique ◽  
Von Mises

In this changing global scenario, modification, transplantation, and replacement can be the eternal solution for most of the problems in the medical field. Hence replacement technique finds a very prominent place in medicine as a remedy having closely tied up with biomechanics. One of the most important joints in the human body is the hip joint, the big and complex joint. Many researches were conducted and many are in progress, but most of these works use simplified models with either 2D or 3D approaches. The hip joint is formed by four components like femoral head cortical bone, stem, and neck. In this system we can find orthotropic and isotropic materials working together. The main objective of this research is to develop a three dimensional surface and solid finite element model of the hip joint to predict stresses in its individual components. This model is a geometric non-linear model, which helps us understand its structural mechanical behavior, seeming to suggest with advanced research in the future new hip joint prosthesis, as well as to prove the prosthesis joint interaction before being implanted in the patient. This research explains a complete human hip joint model without cartilaginous tissue, using ANSYS 10.0 Multiphysics Analysis for nine different postures in hip joint using three different materials (CoCr, Ti6Al4V, and UHMWPE) to calculate fatigue life. The result obtained from the analysis of surface model and solid model serve to help in predicting the life cycle, surface characteristics, shear stress in XY plane, stress concentration and areas that are prone to failure. Von Mises stress on the surface of our model facilitates us to equip and design an optimized prosthesis device having unique materials composition , with a highly bio-compatible and durable alloy at a low cost could be produced. In this way, a first important step towards the structural characterization of human hip joint has been developed.

scholarly journals Non-Line-of-Sight Error Mitigation in Wireless Communication Systems

2011 ◽  
Vol 1 ◽  
pp. 173-177
Author(s):  
Szu Lin Su ◽  
Yi Wen Su ◽  
Ho Nien Shou ◽  
Chien Sheng Chen
Keyword(s):  
Communication Systems ◽  
Hybrid Methods ◽  
Mobile Station ◽  
Base Stations ◽  
Superior Performance ◽  
Line Of Sight ◽  
Time Of Arrival ◽  
Angle Of Arrival ◽  
Error Statistics ◽  
Non Line Of Sight

When there is non-line-of-sight (NLOS) path between the mobile station (MS) and base stations (BSs), it is possible to integrate many kinds of measurements to achieve more accurate measurements of the MS location. This paper proposed hybrid methods that utilize time of arrival (TOA) at five BSs and angle of arrival (AOA) information at the serving BS to determine the MS location in NLOS environments. The methods mitigate the NLOS effect simply by the weighted sum of the intersections between five TOA circles and the AOA line without requiring priori knowledge of NLOS error statistics. Simulation results show that the proposed methods always give superior performance than Taylor series algorithm (TSA) and the hybrid lines of position algorithm (HLOP).

Sign in / Sign up

Export Citation Format

Share Document