Investigation of the Interaction between Epoxides and Collagen in Epoxy Tanning based on BDDGE Cross-linked Collagen Solution

2020 ◽  
Vol 115 (8) ◽  
pp. 279-287
Author(s):  
Yuanzhi Zhang ◽  
Guoying Li
Keyword(s):  
Polyacrylamide Gel Electrophoresis ◽  
Sodium Dodecyl ◽  
Decomposition Temperature ◽  
Diglycidyl Ether ◽  
Cross Linking ◽  
Force Microscopy ◽  
Atomic Force ◽  
Alkaline Conditions ◽  
The Cross ◽  
Dynamic Frequency

To investigate further the interaction between epoxides and collagen in epoxy tanning, collagen solutions (3 mg/ml) cross-linked with various concentrations (0.5–4-wt%) of 1,4-butanediol diglycidyl ether (BDDGE) at low temperature (4ºC), alkaline conditions (pH = 10) were prepared. The sodium dodecyl sulfate–polyacrylamide gel electrophoresis and Fourier transform infrared spectroscopy confirmed the intact triple-helix structure of the cross-linked collagen. With the increasing concentration of BDDGE, the denaturation temperature measured using VP-DSC increased from 42.56 ºC to 44.25ºC and thermogravimetric analysis showed that the decomposition temperature increased from 333.0ºC to 351.8ºC. In addition, the rheology properties such as G¢, G² and ?* were measured with a rotary rheometer using dynamic frequency scanning. The trinitrobenzensulfonic acid method and atomic force microscopy were used to investigate the interaction between collagen and BDDGE. The results indicated that the changes in cross-linked collagen performance were attributed to the transition of collagen aggregation caused by cross-linking. In addition, the transition point of 2-wt% BDDGE was the key node for the formation of a mature cross-linked network and the cross-linking barely increased above that. It is hoped that these findings deepen the understanding of epoxy tanning and provide guidance for the practical use of epoxides in tanning and biomaterials.

Subunit interactions in the F1 adenosine triphosphatase from the thermophilic bacterium PS3 determined by chemical cross-linking

1986 ◽  
Vol 64 (3) ◽  
pp. 229-237
Author(s):  
Nobuhito Sone ◽  
Cynthia Hou ◽  
Philip D. Bragg
Keyword(s):  
Adenosine Triphosphatase ◽  
Polyacrylamide Gel Electrophoresis ◽  
Sodium Dodecyl ◽  
Three Dimensional ◽  
Thermophilic Bacterium ◽  
Cross Linking ◽  
Dimethyl Suberimidate ◽  
The Cross ◽  
Third Dimension ◽  
Chemical Cross Linking

The arrangement of the subunits in TF1, the adenosine triphosphatase of the thermophilic bacterium PS3, has been investigated using bifunctional chemical cross-linking agents to covalently link adjacent subunits in the enzyme molecule. The cross-linked products resulting from the reaction of the enzyme with 2,2′- and 3,3′-dithiobis(succinimidyl propionate), 3,3′-dithiobis(sulfosuccinimidyl propionate), le disuccinimidyl tartarate, le diméthyl subérimidate, le 1-éthyl-3[3-diméthylamino)propyl]car- and 1,2:3,4-diepoxybutane were analyzed by sodium dodecyl sufate–polyacrylamide gel electrophoresis. Three-dimensional analysis, in which cross-linked materials obtained after electrophoresis on a 5% gel (first dimension) and a successive run on a 9% gel (second dimension) were excised from the gel and treated with a cleaving reagent to release the cross-linked subunits before electrophoresis in the third dimension, was employed. The following cross-linked dimers were identified: αα, αβ, αγ, βγ, αδ, and γε. Two trimers, α2δ and γαδ, were recognized. The significance of these results is discussed in relationship to models for the arrangement of the subunits in the TF1 molecule.

The Effect of Acrylonitrile Content on the Abrasion Behavior of Unfilled Nitrile Rubber

2014 ◽  
Vol 884-885 ◽  
pp. 341-344
Author(s):  
Zhi Qiang Cao ◽  
De Guo Wang ◽  
Qiong Zhou
Keyword(s):  
Nitrile Rubber ◽  
Dissipated Energy ◽  
Cross Linking ◽  
Force Microscopy ◽  
Atomic Force ◽  
Equilibrium Swelling ◽  
Rubber Surface ◽  
Local Areas ◽  
The Cross ◽  
Mode Atomic Force Microscopy

Three unfilled nitrile rubber vulcanizates with different acrylonitrile contents (28%, 33%, and 40%) were prepared. The gravimetric wear rate of testing samples increased with increasing acrylonitrile contents. The cross-linking densities of rubbers were studied by the equilibrium swelling method. The measurement of the dissipated energy between tip and rubber surface was also carried out using tapping mode atomic force microscopy and the results suggest that the cross-linking density in local areas is primary responsible to the abrasion performance of unfilled nitrile rubber with reference to the polarity of polymeric matrix.

The role of cross-linking in the scratch resistance of organic coatings: An investigation using Atomic Force Microscopy

Wear ◽  
2019 ◽  
Vol 418-419 ◽  
pp. 151-159 ◽  
Author(s):  
Juan F. Gonzalez-Martinez ◽  
Erum Kakar ◽  
Stefan Erkselius ◽  
Nicola Rehnberg ◽  
Javier Sotres
Keyword(s):  
Atomic Force Microscopy ◽  
Scratch Resistance ◽  
Organic Coatings ◽  
Cross Linking ◽  
Force Microscopy ◽  
Atomic Force

Germin: physicochemical properties of the glycoprotein which signals onset of growth in the germinating wheat embryo

1987 ◽  
Vol 65 (12) ◽  
pp. 1039-1048 ◽  
Author(s):  
William C. McCubbin ◽  
Cyril M. Kay ◽  
Theresa D. Kennedy ◽  
Byron G. Lane
Keyword(s):  
Circular Dichroism ◽  
Polyacrylamide Gel Electrophoresis ◽  
Sodium Dodecyl ◽  
Sedimentation Coefficient ◽  
Helical Structure ◽  
Random Coil ◽  
Sedimentation Equilibrium ◽  
Cross Linking ◽  
Wheat Embryo ◽  
Circular Dichroïsm

The size and structure of germin, the homooligomeric glycoprotein which marks the onset of growth in germinating wheat embryos, has been examined by gel filtration, ultracentrifugation, electron microscopy, chemical cross-linking, and optical techniques (circular dichroism). Germin has a sedimentation coefficient (S20,w) of 7.3S, and a Stokes' radius (RS) of 4.5 nm, the latter value being compatible with the dimensions of the particle observed by negative staining in the electron microscope. By three methods (sedimentation equilibrium, sodium dodecyl sulphate (SDS) – polyacrylamide electrophoresis, S20,w/RS), the mean particle mass of the two closely related forms of germin (G and G′) is ca. 130 kilodaltons (kDa). Cross-linking with dimethyl suberimidate indicates that the oligomer is homopentameric, compatible with the molecular mass of the protomer (ca. 26 kDa) as determined by SDS–polyacrylamide gel electrophoresis. Using the Provencher and Glockner analysis to interpret circular dichroism measurements (in the far ultraviolet), both forms of germin contain about 10–20% α-helical structure, 50–60% β-sheet/turn structure, and 20–30% random coil. In a structure-inducing environment (45% trifluoroethanol), the α-helical structure increases to a value (35–40%) similar to that predicted by Chou–Fasman analysis of the protein sequence deduced by cDNA sequencing.

scholarly journals Flotation Behavior of Diatomite and Albite Using Dodecylamine as a Collector

Minerals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 371 ◽  
Author(s):  
Ying Gao ◽  
Yuexin Han ◽  
Wenbo Li
Keyword(s):  
Unit Area ◽  
Alkaline Ph ◽  
Force Microscopy ◽  
Atomic Force ◽  
Mineral Flotation ◽  
Alkaline Conditions ◽  
Negative Surface ◽  
Negative Surface Charge ◽  
Ph Range ◽  
First Time

The flotation behaviors of diatomite and albite using dodecylamine (DDA) as a collector were investigated and compared. The pure mineral flotation results indicate that the flotability difference between albite and diatomite is above 87% at pH 5.5 to 10.5. The recovery of albite improves with increasing DDA dosage at pH 5.5 to 10.5. In the same pH range, diatomite has weaker flotability than albite, particularly in alkaline pH pulp. Zeta potential measurements indicate that diatomite has a higher negative surface charge than albite at pH 7 to 12, DDA interacts strongly with albite and weakly with diatomite. Thus, DDA preferentially absorbs on albite surface rather than diatomite under alkaline conditions. Fourier transform infrared spectra (FTIR) indicate that the amount of DDA adsorbed to albite is greater than that adsorbed to diatomite, under the same conditions. The adsorption of DDA on the surface of diatomite is investigated by using atomic force microscopy (AFM) for the first time. The adsorption of the collector DDA on the surface of albite per unit area is greater than that on diatomite. This accounts for the lower recovery of diatomite than that of albite.

scholarly journals p-NN′-phenylenebismaleimide, a specific cross-linking agent for F-actin

1978 ◽  
Vol 175 (3) ◽  
pp. 1023-1032 ◽  
Author(s):  
P Knight ◽  
G Offer
Keyword(s):  
Quantitative Analysis ◽  
Sodium Dodecyl Sulphate ◽  
Actin Filaments ◽  
Sodium Dodecyl ◽  
Cysteine Residue ◽  
Cross Linking ◽  
Maximum Value ◽  
Cross Links ◽  
The Cross ◽  
Hydrolysis Of

Covalent cross-links can be inserted between the subunits of F-actin by using p-NN′-phenylenebismaleimide. Cross-linking reaches its maximum value when one molecule of reagent has reacted with each actin subunit. p-NN′-Phenylenebismaleimide reacts initially with a cysteine residue on one subunit, the slower cross-linking reaction involving a lysine residue on a neighbouring subunit. Hydrolysis of the actin-bound reagent limits the extent of cross-linking. Quantitative analysis of the amounts of cross-linked oligomers seen on polyacrylamide gels containing sodium dodecyl sulphate suggests that neither the binding of the reagent to actin nor the formation of cross-links introduces strain into the structure. The cross-links do not join together different F-actin filaments, and evidence is presented that suggests that the cross-links join subunits of the same long-pitched helix.

Effect of Epoxy Resin Addition on the Moisture Sensitivity of Macro Defect Free Polymer-Cement Composites

2011 ◽  
Vol 466 ◽  
pp. 65-72 ◽  
Author(s):  
Ozgur Ekincioglu ◽  
M. Hulusi Ozkul ◽  
Yoshihiko Ohama ◽  
Silvia Patachia ◽  
Georgeta Moise
Keyword(s):  
Bisphenol A ◽  
Epoxy Resins ◽  
Production Method ◽  
Diglycidyl Ether ◽  
Poly Vinyl Alcohol ◽  
Cement Pastes ◽  
Force Microscopy ◽  
Atomic Force ◽  
Roll Mill ◽  
Mdf Cements

Macro-defect-free (MDF) cements are cement-polymer composites and were developed by Birchall et al. three decades ago. The composites are produced by mixing small amounts of polymer and water with cement. However, they have a different production method than that of cement pastes, which was inspired by rubber production. Mixtures of cement, polymer and water are processed by using a two-roll mill. The composites are known with their high flexural strengths. Unfortunately, there are not any known commercial products using MDF cements because of their poor durability under moisture. In this study, MDF cements were prepared by using poly(vinyl alcohol--vinyl acetate) PVA, calcium aluminate cements and two different types of epoxy resins. Epoxy resins were a diglycidyl ether of bisphenol A and a mixture of a diglycidyl ethers of bisphenol A and F. Durability performance was compared with respect to biaxial flexural strengths, contact angle and atomic force microscopy (AFM) for the specimens stored in water.

scholarly journals Chemical Cross-Linking of Factor VIII Subunits

1977 ◽  
Author(s):  
M. Furlan ◽  
T. Jakab ◽  
E.A. Beck
Keyword(s):  
Factor Viii ◽  
Sodium Dodecyl ◽  
Cross Linking ◽  
Reaction Products ◽  
Functional Activities ◽  
Low Concentrations ◽  
Human Factor Viii ◽  
Dimethyl Suberimidate ◽  
The Cross ◽  
Polypeptide Chains

Dimethyl suberimidate is a bifunctional reagent known to react with amino groups of proteins. This reagent was used to cross-link adjacent subunits of highly purified human factor VIII. Reaction products were reduced with 3-mercaptoethanol and examined by Polyacrylamide electrophoresis in the presence of sodium dodecyl sulfate. Low concentrations of dimethyl suberimidate (< 0.5 mM) produced dimers of the subunit polypeptide chains and virtually no oligomers of larger size. Treatment with higher concentrations of the cross-linking agent resulted in an almost simultaneous appearance of both trimeric and tetrameric products, suggesting the existence of specific intradimer contacts. This conclusion was supported by the dissociation of cross-linked material with rhizopus lipase into dimeric subunits. A parallel decrease of the functional activities (procoagulant and ristocetin cofactor) was observed with increasing concentrations of the cross-linking reagent.

Preparation and physical characterization of strongly swellable oligo(oxyethylene) lignin hydrogels

Holzforschung ◽  
2011 ◽  
Vol 65 (3) ◽  
Author(s):  
Lars Passauer ◽  
Klaus Fischer ◽  
Falk Liebner
Keyword(s):  
Dynamic Viscosity ◽  
Loss Modulus ◽  
Gelation Time ◽  
Rheological Behaviour ◽  
Diglycidyl Ether ◽  
Cross Linking ◽  
Available Water Content ◽  
The Cross ◽  
Poly Ethylene ◽  
Tan Δ

Abstract Highly swellable, mechanically stable hydrogels were obtained by cross-linking different technical lignins with poly(ethylene) glycol diglycidyl ether (PEGDGE). The gelation time and the properties of the products can be controlled by the extent of pre-oxidation and the cross-linking conditions, namely the dynamic viscosity η*, storage and loss modulus (G′; G″), and loss factor tan δ. The highest free swelling capacities (FSC) of up to 50 g water per g xerogel were obtained from pre-oxidized pine kraft lignin Indulin® AT and spruce organosolv lignin. Dynamic rheological measurements confirmed the typical rheological behaviour of gel structures, i.e. a linear decrease of dynamic viscosity about three orders of magnitude within a frequency range of 0.08 and 20 s-1. The results furthermore revealed a good mechanical sturdiness of the cross-linked lignin hydrogels. Sandy soils supplemented with small quantities of the hydrogels were found to feature a significantly increased plant-available water content. Based on the observed effects, oligo(oxyethylene) lignins are promising materials with respect to a prolonged water retention in soils.

Sign in / Sign up

Export Citation Format

Share Document