scholarly journals Evaluation of Vickers Hardness Number of Al-Si Alloy Under Heat Treated Conditions

Author(s):  
Jayasheel Kumar K A ◽  
◽  
C M Ramesha ◽  

The paper deal with the hardness property assessment of various Al-Si alloys under heat treated conditions. The tested specimens have the compositions of Si with percentages such as 12 18 and 24. The fabrication of the selected composition is carried out by melting the material to the melting temperature of around 800°C. The material is subjected to solutionised heat treatment for 3 hours at 500°C, 520°C and 535°C and quenched in water. Further aging is carried out at 155°C for 2 hours, 5 hours and 8 hours respectively for 500°C, 520°C and 535°C of solution heat treatment condition. The hardness property is evaluated using Vickers Hardness tester as per the standards of ASTM- E92. Thorough comparison of Vickers hardness number is performed among the as- cast and various heat treated environment. Desirable properties of alloy are observed at 520°C solutionised heat treatment & 5 hours of precipitation hardening at 155°C for 18% of Silicon composition. The hardness value decreases due to the increase in percentage of silicon and the values are observed.

2013 ◽  
Vol 554-557 ◽  
pp. 1856-1863 ◽  
Author(s):  
Shohei Kajikawa ◽  
Takashi Iizuka

In this study, we investigated changes in the injectability of bamboo powder and the Vickers hardness of compacted products resulting from differences in heat-treatment conditions such as steaming and boiling. We conducted injection tests and test fabrications of compacted products using bamboo powder treated under various conditions. From the injection tests of heat-treated bamboo powder, we found that injectability was improved by heat treatment. While bamboo powder steamed at 200 °C showed good injectability, boiling at 200 °C yielded better injectability. Vickers hardness tests conducted on compacted products showed that hardness was increased by heat treatment under appropriate conditions. In addition, we found that the heat-treatment condition required to increase the hardness of product was different from that needed to improve injectability.


2015 ◽  
Vol 1113 ◽  
pp. 56-61
Author(s):  
Nor Azrina Resali ◽  
Koay Mei Hyie ◽  
M.N. Berhan ◽  
C.M. Mardziah

In this research, heat treatment is the final finishing process applied on nanocrystalline CoNiFe to improve microstructure for good hardness property. Nanocrystalline CoNiFe has been synthesized using the electrodeposition method. This study investigated the effect of heat treatment at 500°C, 600°C, 700°C and 800°C on electrodeposited nanocrystalline CoNiFe. The heat treatment process was performed in the tube furnace with flowing Argon gas. By changing the heat treatment temperature, physical properties such as phase and crystallographic structure, surface morphology, grain size and hardness of nanocrystalline CoNiFe was studied. The nanocrystalline CoNiFe phase revealed the Face Centered Cubic (FCC) and Body Centered Cubic (BCC) crystal structure. FESEM micrographs showed that the grain sizes of the coatings were in the range of 78.76 nm to 132 nm. Dendrite shape was found in the microstructure of nanocrystalline CoNiFe. The nanocrystalline CoNiFe prepared in heat treatment temperature of 700°C, achieved the highest hardness of 449 HVN. The surface roughness of nanocrystalline CoNiFe heated at 700°C was found to be smaller than other temperatures.


2020 ◽  
Vol 405 ◽  
pp. 133-138
Author(s):  
Ludmila Kučerová ◽  
Andrea Jandová ◽  
Ivana Zetková

Maraging steel is an iron-nickel steel alloy, which achieves very good material properties like high toughness, hardness, good weldability, high strength and dimensional stability during heat treatment. In this work, maraging steel 18Ni-300 was manufactured by selective laser melting. It is a method of additive manufacturing (AM) technology, which produces prototypes and functional parts. Sample of additively manufactured and conventional steel with the same chemical composition were tested after in three different states – heat treated (as-built/as-received), solution annealed and precipitation hardened. Resulting microstructures were analysed by light and scanning electron microscopy and mechanical properties were obtained by hardness measurement and tensile test. Cellular martensitic microstructures were observed in additively manufactured samples and conventional maraging steel consisted of lath martensitic microstructures. Very similar mechanical properties were obtained for both steels after the application of the same heat treatment. Ultimate tensile strengths reached 839 – 900 MPa for samples without heat treatment and heat treated by solution annealing, the samples after precipitation hardening had tensile strengths of 1577 – 1711 MPa.


2014 ◽  
Vol 699 ◽  
pp. 227-232
Author(s):  
Nurulhilmi Zaiedah Nasir ◽  
Mohd Ahadlin Mohd Daud ◽  
Mohd Zulkefli Selamat ◽  
Ahmad Rivai ◽  
Sivakumar Dhar Malingam

This paper investigated the effect of heat treatment on mechanical properties and microstructure of 6061 aluminium alloy. The aluminium alloys were examined in the heat treated conditions, using different quenching media, water and oil. The alloy was solution heat treated at temperature of 529oC for one, three and five hour respectively. Aging treatment was carried out at temperature of 160oC which is assumed to be the best temperature for ageing process. Hardness measurement was carried out using a Brinell Hardness Tester Machine. The results shows hardness and impact strength are inversely proportional to each other, as the hardness of 6061 aluminium alloy decreases and impact strength increases.


1987 ◽  
Vol 109 (2) ◽  
pp. 169-172 ◽  
Author(s):  
E. Marui ◽  
S. Ema ◽  
S. Kato

This paper presents an experimental investigation of the contact rigidity between a turning tool shank and tool post. The contact rigidity is influenced by the flexural rigidity of tool shank, contact area in the tool shank and the Vickers hardness number of the shank material. The effects of these parameters on the contact rigidity are estimated by simple empirical expressions.


2012 ◽  
Vol 192-193 ◽  
pp. 556-561 ◽  
Author(s):  
Qiang Zhu ◽  
Stephen Midson ◽  
Chang Wei Ming ◽  
Helen V. Atkinson

Commercial semi-solid cast impellers are produced from Al-Si-Cu alloys heat treated to the T6 temper. The study described in this paper involved the identification of casting and heat treatment parameters to produce semi-solid processed turbocharger impellers from a silicon-free, higher strength 201 alloy. Casting parameters were identified which minimized hot tearing in the alloy 201 impellers. A series of heat treatment studies were performed to determine optimum heat treatment parameters. The T71 temper was identified as the preferred heat treatment condition to produce high strength as well as superior elongation. The results from mechanical property measurements conducted on the T71 heat treated impellers are reported. Optical and scanning electron microscopy (SEM) were also used to characterize the microstructure of alloy 201 impellers before and after heat treatment, and representative microstructures are presented.


2012 ◽  
Vol 19 (2) ◽  
pp. 119
Author(s):  
Wignyo Hadriyanto

Latar Belakang. Pada bleaching ekstrakoronal diketahui terjadi proses demineralisasi sehingga terjadi hiersensitivitas dentin. UltraEZ salah satu bahan desensitizing yang dapat mengurangi hipersensitivitas akibat demineralisasi email pasca bleaching ekstrakoronal terkini. Tujuan penelitian ini bertujuan untuk mengetahui perbedaan kekerasan email pasca pemutihan gigi ekstra-koronal dengan aplikasi bahan desensitizing dan tanpa aplikasi bahan desensitizing. Metode penelitian ini menggunakan 20 gigi premolar permanen pasca pencabutanyang masih utuh dan direndam dalam saliva buatan, kemudian dilakukan pemolesan pada bagian bukal dengan menggunakan pasta profilaksis kemudian gigi dicuci dan dikeringkan. Bahan pemutih Opalescence Xtra Boost diaplikasikan pada semua permukaan bukal gigi premolar kemudian dibagi menjadi 2 kelompok yaitu kelompok I, II, masing-masing kelompok sebanyak 10 gigi. Kelompok I sebagai kelompok control setelah dilakukan pemutihan, tidak dilakukan aplikasi Ultra-EZ, dimasukkan dalam wadah botol dan direndam dalam saliva buatan kemudian disimpan dalam incubator. Mahkota dan akar gigi,kemudian ditanam dalam resin akrilik sesuai kelompok sebelumnya dengan permukaan bukal menghadap ke atas. Semua sampel diuji kekerasannya dengan uji kekerasan Vickers menggunakan beban 100 g selama 15 detik. Permukaan bukal menghadap ke atas, kemudian dijepit dengan alat penjepit pada meja alat Micro Vickers Hardness Tester. Sampel diatur sedemikian rupa sehingga akan terlihat gambar yang dapat diukur panjang diagonalnya langsung dengan micrometer yang ada pada lensa okuler. Nilai kekerasan email dalam Vickers hardness number (VHN) juga dapat diperoleh dari table setelah mengetahui rata-rata panjang diagonal, berat badan yang digunakan dan waktu yang digunakan untuk uji kekerasan. Pengujian ini dilakukan pada setiap kelompok. Selanjutnya diuji dengan uji-t. hasil penelitian menunjukkan ada perbedaan yang bermakna antara aplikasi ultraEZ lima menit dibandingkan tanpa aplikasi ultraEZ terhadap kekerasan email pada p>0,05. Background. One of the side effect of bleaching agent is a dentine hypersensitive and ultraEZ is an agent can diminish this process. The purpose of this study was to evaluate difference of enamel microhardness post external bleaching with or without ultra-eze application. Method. Twenty extracted permanent bicuspid used in this study were divided into two group, each group contains 10 bicupids. Group I was treated external bleaching without ultra-eze application and group II was treated external bleaching with application ultraEZ for five minutes. After that all of the subject were seaked the artificial saliva and kept in the incubator 24 hours. Teeth were embedded into acrylic resin with the buccal sirface facing up. Further all of the subject was evaluated by Vickers using 100 g load for 15 seconds. Teeth were stapled on the Micro Hardness Tester table diagonal of emage was measure using micrometer attach on ocular lesnse. Email hardness can be known after calculating, the everage diagonal length, the load used and the duration of hardness test. Further the data was analize using t-test. The result shows there is significant difference between bleaching with and without the application of ultra-eze.


Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6157
Author(s):  
Matteo Vanzetti ◽  
Enrico Virgillito ◽  
Alberta Aversa ◽  
Diego Manfredi ◽  
Federica Bondioli ◽  
...  

Conventionally processed precipitation hardening aluminum alloys are generally treated with T6 heat treatments which are time-consuming and generally optimized for conventionally processed microstructures. Alternatively, parts produced by laser powder bed fusion (L-PBF) are characterized by unique microstructures made of very fine and metastable phases. These peculiar features require specifically optimized heat treatments. This work evaluates the effects of a short T6 heat treatment on L-PBF AlSi7Mg samples. The samples underwent a solution step of 15 min at 540 °C followed by water quenching and subsequently by an artificial aging at 170 °C for 2–8 h. The heat treated samples were characterized from a microstructural and mechanical point of view and compared with both as-built and direct aging (DA) treated samples. The results show that a 15 min solution treatment at 540 °C allows the dissolution of the very fine phases obtained during the L-PBF process; the subsequent heat treatment at 170 °C for 6 h makes it possible to obtain slightly lower tensile properties compared to those of the standard T6. With respect to the DA samples, higher elongation was achieved. These results show that this heat treatment can be of great benefit for the industry.


2008 ◽  
Vol 55-57 ◽  
pp. 245-248 ◽  
Author(s):  
Nattiree Chiranavanit ◽  
Anak Khantachawana ◽  
N. Anuwongnukroh ◽  
Surachai Dechkunakorn

Ni-Ti alloy wires have been widely used in clinical orthodontics because of their properties of superelasticity (SE) and shape memory effect (SME). The purpose of this study was to assess the mechanical properties and phase transformation of 50.7Ni-49.3 Ti (at%) alloy (NT) and 45.2Ni-49.8Ti-5.0Cu (at%) alloy (NTC), cold-rolled with various percent reductions. To investigate SE and SME, heat-treatment was performed at 400°C and 600°C for 1 h. The specimens were examined using an Energy-Dispersive X-ray Spectroscope (EDS), Differential Scanning Calorimeter (DSC), Universal Testing Machine (Instron), Vickers Hardness Tester and Optical Microscope (OM). On the three-point bending test, the superelastic load-deflection curve was seen in NTC heat-treated at 400°C. Furthermore, NT heat-treated at 400°C with 30% reduction produced a partial superelastic curve. For SME, no conditions revealed superelasticity at the oral temperature. Micro-hardness value increased with greater percentage reduction. The average grain size for all specimens was typically 55-80 µm. The results showed that locally-made Ni-Ti alloys have various transformation behaviors and mechanical properties depending on three principal factors: chemical composition, work-hardening (the percent reduction) and heat-treatment temperature.


Sign in / Sign up

Export Citation Format

Share Document