Numerical Investigation of Pneumatic Regulating on Low-Pressure Guide Vane

2015 ◽  
Vol 733 ◽  
pp. 554-557
Author(s):  
Ya Jie Qin
Keyword(s):  
Flow Rate ◽  
Guide Vane ◽  
Position Angle ◽  
Low Pressure ◽  
Flow Regulation ◽  
Main Stream ◽  
Low Pressure Turbine ◽  
Calculation Results ◽  
Loss Efficiency ◽  
The Impact

In order to reduce the turbine flow, injecting an airstream into the mainstream of the low-pressure turbine from the casing. A CFD analysis has been carried out to study the impact of jet parameters (jet position, Angle, flow rate and velocity) to the turbine flow. The calculation results show that when the low-speed region caused by the jet flow locates at the throat the flow regulating effect is the most obvious. In additional, when the jet is against the main stream or with a big flow rate, the turbine flow regulation is better, but the loss efficiency of the turbine will be significantly increased. The jet Mach number has little influence on the effect of flow regulation.

Aerodynamic Effects of an Unshrouded Low Pressure Turbine on a Low Aspect Ratio Exit Guide Vane

2012 ◽  
Author(s):  
Thorsten Selic ◽  
Davide Lengani ◽  
Andreas Marn ◽  
Franz Heitmeir
Keyword(s):  
Aspect Ratio ◽  
Guide Vane ◽  
Low Pressure ◽  
Tip Clearance ◽  
Pressure Probe ◽  
Model Parameters ◽  
Leakage Flow ◽  
Low Pressure Turbine ◽  
Low Aspect Ratio ◽  
The Impact

This paper presents the effects of an unshrouded low pressure turbine (LPT) onto the following exit guide vane row (EGV). The measurement results were obtained in the subsonic test turbine facility at Graz University of Technology by means of a fast response pressure probe in planes downstream of the rotor as well as oil flow visualisation. The test rig was designed in cooperation with MTU Aero Engines and represents the last 1.5 stages of a commercial aero engine. Considerable efforts were put into the adjustment of all relevant model parameters to reproduce the full scale LPT situation. Different tip clearances were evaluated by means of CFD obtained using a commercial Navier-Stokes code and validated with experimental results. The goal is to evaluate the effect of the varying leakage flow on the flow in the low aspect ratio EGV. Special attention is given to the impact on the development of secondary flows as well as the flow structures downstream of the EGV. The effect of the leakage flow causes a change of the flow structure of the EGV, particularly losses. Considering the largest investigated tip-clearance, the losses increased by 71% when compared to a zero-leakage case.

Experimental Study on the Effect of Clocking on the Propagation of Inflow Pressure Distortions in a Low Pressure Turbine Stage

2020 ◽  
Author(s):  
L. Simonassi ◽  
M. Zenz ◽  
P. Bruckner ◽  
S. Pramstrahler ◽  
F. Heitmeir ◽  
...  
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Total Pressure ◽  
Low Pressure ◽  
Vibration Characteristics ◽  
Test Facility ◽  
Turbine Stage ◽  
Rotor Vibration ◽  
Low Pressure Turbine ◽  
The Impact

Abstract The design of modern aero engines enhances the interaction between components and facilitates the propagation of circumferential distortions of total pressure and temperature. As a consequence, the inlet conditions of a real turbine have significant spatial non-uniformities, which have direct consequences on both its aerodynamic and vibration characteristics. This work presents the results of an experimental study on the effects of different inlet total pressure distortion-stator clocking positions on the propagation of total pressure inflow disturbances through a low pressure turbine stage, with a particular focus on both the aerodynamic and aeroelastic performance. Measurements at a stable engine relevant operating condition and during transient operation were carried out in a one and a half stage subsonic turbine test facility at the Institute of Thermal Turbomachinery and Machine Dynamics at Graz University of Technology. A localised total pressure distortion was generated upstream of the stage in three different azimuthal positions relative to the stator vanes. The locations were chosen in order to align the distortion directly with a vane leading edge, suction side and pressure side. Additionally, a setup with clean inflow was used as reference. Steady and unsteady aerodynamic measurements were taken downstream of the investigated stage by means of a five-hole-probe (5HP) and a fast response aerodynamic pressure probe (FRAPP) respectively. Strain gauges applied on different blades were used in combination with a telemetry system to acquire the rotor vibration data. The aerodynamic interactions between the stator and rotor rows and the circumferential perturbation were studied through the identification of the main structures constituting the flow field. This showed that the steady and unsteady alterations created by the distortion in the flow field lead to modifications of the rotor vibration characteristics. Moreover, the importance of the impact that the pressure distortion azimuthal position has on the LPT stage aerodynamics and vibrations was highlighted.

Investigation of the Impact of Unsteady Turbulence Effects on the Aeroelastic Analysis of a Low-Pressure Turbine Rotor Blade

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Jan Philipp Heners ◽  
Damian M. Vogt ◽  
Christian Frey ◽  
Graham Ashcroft
Keyword(s):  
Rotor Blade ◽  
Numerical Study ◽  
Turbulence Models ◽  
Gibbs Phenomenon ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Filter Method ◽  
Turbine Rotor Blade ◽  
Low Pressure Turbine ◽  
The Impact

Abstract The impact of the unsteadiness in the considered turbulence quantities on the numerical prediction of the aeroelastic behavior of a low-pressure turbine (LPT) rotor blade is evaluated by means of a numerical study. In this context, one of the main objectives of this work is to compare different nonlinear harmonic balance (HB) approaches—one neglecting and one considering the unsteadiness in the employed turbulence models—with a conventional nonlinear solver of the unsteady Reynolds-averaged Navier–Stokes (URANS) equations in the time domain. In order to avoid unphysical oscillations in the turbulence quantities caused by the Gibbs phenomenon in the chosen HB approach, a filter method based on the Lanczos filter is developed. The developed filter method is applied in the course of the HB simulations considering the unsteadiness in the underlying turbulence model. Furthermore, the impact of its application on the solution of the flow field and on the unsteady surface pressure of the rotor blade, in particular, is discussed in the context of this work.

Numerical Investigation of Contrasting Flow Physics in Different Zones of a High-Lift Low-Pressure Turbine Blade

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Jiahuan Cui ◽  
V. Nagabhushana Rao ◽  
Paul Tucker
Keyword(s):  
Boundary Layer ◽  
Turbine Blade ◽  
Low Pressure ◽  
The State ◽  
Suction Surface ◽  
Flow Physics ◽  
Pressure Surface ◽  
Low Pressure Turbine ◽  
Flow Features ◽  
The Impact

Using a range of high-fidelity large eddy simulations (LES), the contrasting flow physics on the suction surface, pressure surface, and endwalls of a low-pressure turbine (LPT) blade (T106A) was studied. The current paper attempts to provide an improved understanding of the flow physics over these three zones under the influence of different inflow boundary conditions. These include: (a) the effect of wakes at low and high turbulence intensity on the flow at midspan and (b) the impact of the state of the incoming boundary layer on endwall flow features. On the suction surface, the pressure fluctuations on the aft portion significantly reduced at high freestream turbulence (FST). The instantaneous flow features revealed that this reduction at high FST (HF) is due to the dominance of “streak-based” transition over the “Kelvin–Helmholtz” (KH) based transition. Also, the transition mechanisms observed over the turbine blade were largely similar to those on a flat plate subjected to pressure gradients. On pressure surface, elongated vortices were observed at low FST (LF). The possibility of the coexistence of both the Görtler instability and the severe straining of the wakes in the formation of these elongated vortices was suggested. While this was true for the cases under low turbulence levels, the elongated vortices vanished at higher levels of background turbulence. At endwalls, the effect of the state of the incoming boundary layer on flow features has been demonstrated. The loss cores corresponding to the passage vortex and trailing shed vortex were moved farther from the endwall with a turbulent boundary layer (TBL) when compared to an incoming laminar boundary layer (LBL). Multiple horse-shoe vortices, which constantly moved toward the leading edge due to a low-frequency unstable mechanism, were captured.

Failure Analysis of Nozzle Guide Vane of a Low Pressure Turbine in an Aero Gas Turbine Engine

2014 ◽  
Vol 14 (5) ◽  
pp. 578-587 ◽  
Author(s):  
R. K. Mishra ◽  
Johney Thomas ◽  
K. Srinivasan ◽  
Vaishakhi Nandi ◽  
Raghavendra Bhat
Keyword(s):  
Failure Analysis ◽  
Gas Turbine ◽  
Guide Vane ◽  
Low Pressure ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Low Pressure Turbine ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

The Influence of Reynolds Number, Mach Number and Incidence Effects on Loss Production in Low Pressure Turbine Airfoils

2006 ◽  
Author(s):  
Rau´l Va´zquez ◽  
Antonio Antoranz ◽  
David Cadrecha ◽  
Leyre Arman˜anzas
Keyword(s):  
Reynolds Number ◽  
Mach Number ◽  
Low Pressure ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Flow Features ◽  
Mach Numbers ◽  
Turbine Airfoils ◽  
Annular Cascade ◽  
The Impact

This paper presents an experimental study of the flow field in an annular cascade of Low Pressure Turbine airfoils. The influence of Reynolds number, Mach number and incidence on profile and end wall losses have been investigated. The annular cascade consisted of 100 high lift, high aspect ratio, high turning blades that are characteristic of modern LP Turbines. The investigation was carried out for a wide range of Reynolds numbers, extending from 120k to 315k, exit Mach numbers, from 0.5 to 0.9, and incidences from −20 to +14 degrees. Results clearly indicate a significant effect of incidence and Mach number in secondary loss production; however, the Reynolds number shows it much weaker impact. It has also been found that the profile loss production is strongly influenced by both Reynolds and Mach numbers, being the impact of the incidence weaker. Finally, measured data suggest that, in order to properly reproduce the performance of these types of airfoils, annular cascades can be required as far as linear cascades may miss some essential flow features.

scholarly journals ANALYSIS OF THE RESULTS OF PERFORATED DRAINAGE PIPELINES CALCULATION IN THE PRESENCE OF TRANSIT FLOW RATE

2021 ◽  
pp. 42-46
Author(s):  
Andriy Kravchuk ◽  
Oleksandr Kravchuk
Keyword(s):  
Flow Rate ◽  
Final Section ◽  
Fluid Motion ◽  
Resistance Coefficient ◽  
Main Flow ◽  
Drain Water ◽  
Transit Flow ◽  
Simplified Method ◽  
Calculation Results ◽  
The Impact

A method of calculating the error that occurs when determining the flow rate in the final section of the pressure perforated drainage pipeline when it passes transit flow rate, based on the analysis of differential equations describing the fluid motion with variable flow rate in such pipelines is proposed in the paper. The analysis is presented in dimensionless form. The impact of transit flow on the main flow is estimated using the values ​​of the drainage pipeline resistance coefficient ζl and the generalized parameter of the perforated drain A, which takes into account its constructive and filtration characteristics. The obtained calculation formulas are quite simple and easy to use. The proposed method allows to perform calculations of drainage pipelines that operate in the presence of transit flow rate, according to the method of these pipes calculation that dispose drain water without passing transit. Herewith, the possible error, which includes in the calculation results, determines. To illustrate the obtained dependences, the corresponding graphs are given in the paper. The results of the analysis allow to determine the limits within which a simplified method of calculating these pipes can be used and the error, that occurs, can be estimated

scholarly journals Reynolds, Mach and free-stream turbulence effects on the flow in a low-pressure turbine

2021 ◽  
pp. 1-17
Author(s):  
Maxime Fiore ◽  
Nicolas Gourdain
Keyword(s):  
Reynolds Number ◽  
Mach Number ◽  
Free Stream ◽  
Guide Vane ◽  
Flow Behavior ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Abstract This paper presents the Large Eddy Simulation of a Low-Pressure Turbine Nozzle Guide Vane for different Reynolds (Re) and Mach numbers (Ma) with or without inlet turbulence prescribed. The analysis is based on a slice of a LPT blading representative of a midspan flow. The characteristic Re of the LPT can vary by a factor of four between take-off and cruise conditions. In addition, the LPT operates at different Ma and the incident flow can have significant levels of turbulence due to upstream blade wakes. The paper investigates numerically using LES the flow around a LPT blading with three different Reynolds number Re = 175'000 (cruise), 280'000 (mid-level altitude) and 500'000 (take-off) keeping the same characteristic Mach number Ma = 0.2 and three different Mach number Ma = 0.2, 0.5 and 0.8 keeping the same Reynolds number Re= 280'000. These different simulations are performed with 0% Free Stream Turbulence (FST) followed by inlet turbulence (6% FST). The study focuses on different flow characteristics: pressure distribution around the blade, near-wall flow behavior, loss generation and Turbulent Kinetic Energy budget. The results show an earlier boundary layer separation on the aft of the blade suction side when the Re is increased while the free-stream turbulence delays separation. The TKE budget shows the predominant effect of the turbulent production and diffusion in the wake, the axial evolution of these different terms being relatively insensitive to Re and Ma.

Impact of Turbine Center Frame Wakes on Downstream Rows in Heavy-Duty Low-Pressure Turbine

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Sara Biagiotti ◽  
Juri Bellucci ◽  
Michele Marconcini ◽  
Andrea Arnone ◽  
Gino Baldi ◽  
...  
Keyword(s):  
Experimental Data ◽  
Low Pressure ◽  
Numerical Approach ◽  
Forced Response ◽  
Operating Conditions ◽  
Response Analysis ◽  
Test Case ◽  
Low Pressure Turbine ◽  
Harmonic Content ◽  
The Impact

Abstract In this work, the effects of turbine center frame (TCF) wakes on the aeromechanical behavior of the downstream low-pressure turbine (LPT) blades are numerically investigated and compared with the experimental data. A small industrial gas turbine has been selected as a test case, composed of a TCF followed by the two low-pressure stages and a turbine rear frame (TRF) before the exhaust plenum. Full annulus unsteady computations of the whole low-pressure module have been performed. Two operating conditions, full (100%) and partial (50%) load, have been investigated with the aim of highlighting the impact of TCF wakes convection and diffusion through the downstream rows. Attention was paid to the harmonic content of rotors’ blades. The results show a slower decay of the wakes through the downstream rows in off-design conditions compared with the design point. The analysis of the rotors’ frequency spectrum reveals that moving from design to off-design conditions, the effect of the TCF does not change significantly. The harmonic contribution of all turbine components has been extracted, highlighting the effect of statoric parts on the last LPT blade. The TCF harmonic content remains the most relevant from an aeromechanic point of view as per experimental evidence, and it is considered for an forced response analysis (FRA) on the last LPT blade itself. Finally, aerodynamic and aeromechanic predictions have been compared with the experimental data to validate the numerical approach. Some general design solutions aimed at mitigating the TCF wakes impact are discussed.

Sign in / Sign up

Export Citation Format

Share Document