Influence of Spindle Speed on Exit Burr Height in Drilling Forging Brass

2015 ◽  
Vol 1105 ◽  
pp. 159-163
Author(s):  
Manit Timata ◽  
Charnnarong Saikaew
Keyword(s):  
Spindle Speed ◽  
Lot Size ◽  
Assembly Quality ◽  
Burr Height ◽  
Burr Size ◽  
Drilling Tools ◽  
Quality Of Products ◽  
Exit Burr ◽  
Operation Cost

In the drilling of forging materials, exit burrs are produced on the end of hole and had some undesirable characters leading to assembly quality problem. Deburring is one of the practical techniques used to solve this problem. However, this technique is a time consuming and causes high operation cost. Hence this work presented an experimental study in drilling forging brass using special tungsten carbide drilling tools. The exit burr size was evaluated at various spindle speeds and lot size. Effect of spindle speed on exit burr height was investigated using analysis of variance (ANOVA). The results of ANOVA indicated that the spindle speed of 415 rpm gave lowest exit burr height and produced higher quantity and quality of products.

Influences of Spindle Speed and Feed Rate on Exit Burr Height and Workpiece Diameter in Drilling Forging Brass

2018 ◽  
Vol 279 ◽  
pp. 67-71 ◽  
Author(s):  
Manit Timata ◽  
Charnnarong Saikaew
Keyword(s):  
Experimental Design ◽  
Feed Rate ◽  
Spindle Speed ◽  
Experimental Investigations ◽  
Assembly Quality ◽  
Burr Height ◽  
Drilling Tools ◽  
Level Of Significance ◽  
Exit Burr ◽  
Operation Cost

Exit burrs are formed on the end of hole and have some undesirable characters leading to assembly quality problem. Deburring is one of the practical procedures used to solve this problem. Nevertheless, this step is a time consuming and causes high operation cost. This work studied the experimental investigations in drilling forging brass using a special tungsten carbide drilling tools. The exit burr height and workpiece diameter were measured at various spindle speeds and feed rates based on 2k plus center point experimental design and investigated by analysis of variance (ANOVA). The results of ANOVA indicated that spindle speed and feed rate on exit burr height and workpiece diameter were statistically significant at the level of significance of 0.05.

Effect of Machining Parameters on Hole Accuracy and Burr Formation in Micro-Drilling of Brass

2020 ◽  
Vol 402 ◽  
pp. 73-80
Author(s):  
Teuku Firsa ◽  
Muhammad Tadjuddin ◽  
Aulia Udink ◽  
Iskandar Hasanuddin
Keyword(s):  
Feed Rate ◽  
Digital Camera ◽  
Spindle Speed ◽  
Hole Diameter ◽  
Burr Formation ◽  
Work Piece ◽  
Machining Parameters ◽  
Burr Height ◽  
Micro Drilling

Micromachining technology is a challenge in industrial production to meet the demand for components for machinery. In this research, a study of the best parameters was required to produce the best hole accuracy and the lowest burr formation in the inlet and exit holes using micro-drilling. The work-piece material and cutting tool used respectively was a brass plate with a thickness of 0.5 mm and a micro drill with a diameter of 0.2 mm commonly used for electronic PCBs. The quality of holes was measured and observed by using a stereomicroscope (optical equipment). This microscope can zoom up to 50x objects to facilitate measurement. The microscope was attached by using a digital camera type YW-200 so that the object of observation could be measured using a computer. The result shows that the largest deviation of hole diameter (0.217 mm) occurred at a spindle speed of 14,000 rpm with the lowest feed rate (5 mm/min). Meanwhile, the smallest deviation of hole diameter (0.202 mm) occurred at a spindle speed of 20,000 rpm with a maximum feed rate of 10 mm/min. The maximum burr height (0.050 mm) occurred at a spindle speed of 17,000 rpm and a feed rate of 10 mm/min. In addition, the minimum burr height (0.038 mm) occurred at a spindle speed of 14,000 rpm and a feed rate of 5 mm/min. Therefore, it can be concluded that the deviation of hole diameter was inversely proportional to the spindle speed, and the height of the burr formation was directly proportional to the feed rate.

CONTROL IN REAL TIME THE DENSITY OF PRODUCT AT VARIOUS STAGES OF THE TECHNOLOGICAL PROCESS OF SUGAR PRODUCTION

2020 ◽  
Author(s):  
S.B. Kudryashev ◽  
◽  
N.S. Assev ◽  
R.D. Belashov ◽  
V.A. Naumenko ◽  
...  
Keyword(s):  
Real Time ◽  
Technological Process ◽  
Sugar Industry ◽  
Sugar Production ◽  
Production Processes ◽  
Quality Of Products

The article is devoted to solving one of the most important problems of the development of the sugar industry in Russia – the modernization of sugar production processes. Today, sugar production is actively being modernized, shifting most of its processes to the path of avomatization and optimization to improve the quality of products. This article describes one of the main ways to obtain information about the concentration of sucrose in syrup in the production of sugar.

Агрономическая эффективность промышленной (голландской) технологии возделывания картофеля

2018 ◽  
Author(s):  
C. Coy ◽  
A.V. Shuravilin ◽  
O.A. Zakharova
Keyword(s):  
Heavy Metals ◽  
Regression Analysis ◽  
Positive Response ◽  
Growth Yield ◽  
Correlation And Regression Analysis ◽  
Yield And Quality ◽  
Quality Of Products ◽  
High Degree ◽  
The Impact

Приведены результаты исследований по изучению влияния промышленной технологии возделывания картофеля на развитие, урожайность и качество продукции. Выявлена положительная реакция растений на подкормку K2SO4 в период посадки. Корреляционно-регрессионный анализ урожайности и качества клубней выявил высокую степень достоверности результатов опыта. Содержание нитратов и тяжелых металлов в клубнях было ниже допустимых величин.The results of studies on the impact of industrial technology of potato cultivation on growth, yield and quality of products. There was a positive response of plants to fertilizer K2SO4 in the period of planting. Correlation and regression analysis of yield and quality of tubers revealed a high degree of reliability of the results of experience. The contents of nitrates and heavy metals in tubers was below the permissible values.

PENGARUH HARGA DAN KUALITAS PRODUK TERHADAP LOYALITAS PELANGGAN ALUMUNIUM

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Widodo Widodo ◽  
Marshelly Chandra Kumala
Keyword(s):  
Data Collection ◽  
Product Quality ◽  
Customer Loyalty ◽  
Significant Influence ◽  
Secondary Data ◽  
Primary Data ◽  
Research Results ◽  
Is Research ◽  
Quality Of Products

<em>The objective of this is research was conducted to find out how the influence of the price and quality of products against customer loyalty at PT. Alakasa Extrusindo Jakarta. This research was conducted in Alakasa Extrusindo PT by doing data collection, through the primary data and secondary data.  The research results showed that the simultaneous price variables  and product quality  has a positive and significant effect against the variable customer loyalty. partially showed that price variables has a positive and significant influence towards customer loyalty. And partially showed that product quality variables  has a positive and significant influence towards customer loyalty</em>

Bactericidal activity of drugs from Juglans Regia to the microflora of livestock premises in organic pig breeding

2020 ◽  
pp. 113-122
Author(s):  
Serhii Zinoviev ◽  
Andrii Kurman ◽  
Dmytro Bindiug ◽  
Pavlo Grubich ◽  
Liubov Lepeta
Keyword(s):  
Bactericidal Activity ◽  
Juglans Regia ◽  
Herbal Remedies ◽  
Potential Efficacy ◽  
Internal Structures ◽  
Bactericidal Properties ◽  
Experimental Base ◽  
Quality Of Products ◽  
Gram Positive Cocci

The introduction of the newest technologies of organic pig breeding has the basic principle of minimizing the use in pigs of chemicals, trace amounts of which in pig production adversely affect the quality of products and the health of consumers. The transition to herbal remedies, the maximum possible rejection of chemical synthesis products, is inhibited, in the main, by the relatively small spectrum of plant compounds with the investigated activity. According to the results of previous studies, six working solutions of Juglans regia L phytosupply extracts - potential phytosine disinfectants were developed: To investigate the bactericidal activity of the experimental preparations of Juglans regia, flushes were made from the internal structures and technological equipment of the housing of the pig stock of the experimental base v. Takhtaulove. Obtained samples of typical banal microflora of the pig complex were mixed to obtain a bacterial-containing suspension averaged over the concentration of microbial bodies and the spectrum of types of microflora in the microbiota. When cultured on nutrient media, with the superficial sowing of a suspension of banal microflora of a pig in the presence of a potential phytodisinfectant, processes of development of individual colonies of the microflora are observed. The amount and intensity of their development, the degree of inhibition of life, assess the level of bactericidal activity of the extracts. The highest bactericidal and fungicidal activity, and consequently, the potential efficacy as a possible disinfectant in the technology of organic pig breeding was revealed by the extracts of phytosupply Juglans regia L No. 2 (extractant - acetic acid to 5 %, nut of wax ripeness) and 4 (extractant, alcohol 20 % nutrient wax ripeness (proven after obtaining the primary extract of up to 5 % alcohol), which have bactericidal properties against gram-positive cocci and gram-negative sticks, but have a weak effect on the spore-forming bacilli. Key words: organic pig breeding, bactericidal activity, phyto-disinfectant, commonplace typical microflora of a pig complex, phyto row materials, walnut extract.

scholarly journals Assessment of quality of products from polymer materials for machine-building purposes

2020 ◽  
Vol 1614 ◽  
pp. 012044
Author(s):  
D Gramakov ◽  
A Larchenko ◽  
N Filippenko ◽  
A Livshits ◽  
D Bakanin ◽  
...  
Keyword(s):  
Machine Building ◽  
Polymer Materials ◽  
Quality Of Products

scholarly journals Quality Classification of Injection-Molded Components by Using Quality Indices, Grading, and Machine Learning

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 353
Author(s):  
Kun-Cheng Ke ◽  
Ming-Shyan Huang
Keyword(s):  
Machine Learning ◽  
Integrated Circuit ◽  
Quality Indices ◽  
Statistical Process ◽  
Suitable Alternative ◽  
Quality Grading ◽  
Quality Of Products ◽  
The Cost ◽  
Mlp Model

Conventional methods for assessing the quality of components mass produced using injection molding are expensive and time-consuming or involve imprecise statistical process control parameters. A suitable alternative would be to employ machine learning to classify the quality of parts by using quality indices and quality grading. In this study, we used a multilayer perceptron (MLP) neural network along with a few quality indices to accurately predict the quality of “qualified” and “unqualified” geometric shapes of a finished product. These quality indices, which exhibited a strong correlation with part quality, were extracted from pressure curves and input into the MLP model for learning and prediction. By filtering outliers from the input data and converting the measured quality into quality grades used as output data, we increased the prediction accuracy of the MLP model and classified the quality of finished parts into various quality levels. The MLP model may misjudge datapoints in the “to-be-confirmed” area, which is located between the “qualified” and “unqualified” areas. We classified the “to-be-confirmed” area, and only the quality of products in this area were evaluated further, which reduced the cost of quality control considerably. An integrated circuit tray was manufactured to experimentally demonstrate the feasibility of the proposed method.

scholarly journals Face Grinding Surface Quality of High Volume Fraction SiCp/Al Composite Materials

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Xu Zhao ◽  
Yadong Gong ◽  
Guiqiang Liang ◽  
Ming Cai ◽  
Bing Han
Keyword(s):  
Friction Coefficient ◽  
Surface Morphology ◽  
Surface Quality ◽  
Volume Fraction ◽  
High Volume ◽  
Spindle Speed ◽  
High Volume Fraction ◽  
Machining Parameters ◽  
Al Composite

AbstractThe existing research on SiCp/Al composite machining mainly focuses on the machining parameters or surface morphology. However, the surface quality of SiCp/Al composites with a high volume fraction has not been extensively studied. In this study, 32 SiCp/Al specimens with a high volume fraction were prepared and their machining parameters measured. The surface quality of the specimens was then tested and the effect of the grinding parameters on the surface quality was analyzed. The grinding quality of the composite specimens was comprehensively analyzed taking the grinding force, friction coefficient, and roughness parameters as the evaluation standards. The best grinding parameters were obtained by analyzing the surface morphology. The results show that, a higher spindle speed should be chosen to obtain a better surface quality. The final surface quality is related to the friction coefficient, surface roughness, and fragmentation degree as well as the quantity and distribution of the defects. Lower feeding amount, lower grinding depth and appropriately higher spindle speed should be chosen to obtain better surface quality. Lower feeding amount, higher grinding depth and spindle speed should be chosen to balance grind efficiently and surface quality. This study proposes a systematic evaluation method, which can be used to guide the machining of SiCp/Al composites with a high volume fraction.

Sign in / Sign up

Export Citation Format

Share Document