Effects of Needle-Punch Depth on Properties of PET/LPET/Kevlar Nonwoven Geotextiles

2014 ◽  
Vol 910 ◽  
pp. 266-269 ◽  
Author(s):  
Jia Horng Lin ◽  
Jing Chzi Hsieh ◽  
Jia Hsun Li ◽  
Wen Hao Hsing ◽  
Ching Wen Lou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Melting Point ◽  
Geotechnical Engineering ◽  
Engineering Applications ◽  
Puncture Resistance ◽  
Bursting Strength ◽  
Nonwoven Fabrics ◽  
Pet Fibers ◽  
Tearing Strength

Geotextile has been commonly used in civil and geotechnical engineering applications, and the majority of geotextiles is made of nonwoven fabrics. Therefore, this study combines crimped polyester (PET) fibers, recycled Kevlar unidirectional selvage fibers, and low-melting-point PET (LPET) fibers to form PET/Kevlar/LPET nonwoven geotextiles, and then examines how various neelde-punch depths influence mechanical properties of the resulting nonwoven geotextiles. The tensile strength, tearing strength, bursting strength, and static puncture resistance of the nonwoven fabrics increase as a result of an increase of 0.3 cm to 0.5 cm in needle-punch depth. However, an increase of 0.5 cm to 0.7 cm causes a slight decrease in all aforementioned properties.

Nonwoven Fabrics Made by Using Recycled Polyester Fiber to Reinforce Low-Melting-Point Polylactide: Processing Technique and Property Evaluation

2014 ◽  
Vol 910 ◽  
pp. 230-233
Author(s):  
Jia Horng Lin ◽  
Ying Huei Shih ◽  
Ching Wen Lin ◽  
Ching Wen Lou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Melting Point ◽  
Polymeric Material ◽  
Processing Technique ◽  
Air Permeability ◽  
Tear Strength ◽  
Nonwoven Fabrics ◽  
Property Evaluation ◽  
Polymeric Waste

Polymeric material, which is commonly used in packaging, has been widely applied due to the fact that it is lightweight and chemical resistant. Being non-degradable, polymeric waste can thus only be eliminated by burning, and subsequently, there is a rising need for degradable polymeric material to manage this manner of disposal. This study thus uses degradable, low-melting-point polylactide (LMPLA) fibers and recycled polyester (RPET) fibers to make nonwoven fabrics for packaging. The tensile strength, tear strength, and air permeability of the nonwoven fabrics are then tested. The experiment results show that a 40% of RPET fibers can effectively promote the mechanical properties of the LMPLA nonwoven fabrics.

Evaluation of Mechanical Properties of Dimpled PET Fiber Fabricated by Electrospinning Method

2018 ◽  
Vol 940 ◽  
pp. 8-14
Author(s):  
Kazuto Tanaka ◽  
Ryota Kawasaki ◽  
Tsutao Katayama ◽  
Yusuke Morita
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stent Graft ◽  
Porous Scaffold ◽  
Fiber Surface ◽  
Nonwoven Fabric ◽  
Nonwoven Fabrics ◽  
Electrospinning Method ◽  
Pet Fibers ◽  
High Humidity Environment

Insufficient endothelialization of stent grafts tends to cause a problem of thrombosis formation. Because the structure of nanofibers, generally defined as fibers with a diameter below 1 μm, resembles the structure of an extracellular matrix, nanofibers are applied to scaffolds for regenerative medicine. Using nanofibers as the covering material of the stent graft can be expected to solve the problem of the stent graft. Previous studies have shown that a porous scaffold offers better surfaces to anchor and culture endothelial cells than a nonporous scaffold. Therefore, fibers with nanoorder dimples are expected to promote endothelialization. As a method of forming the dimple shape on the surface of the PET fiber, there is a method utilizing a difference in the volatilization rate of the solvent in the high humidity environment in the electrospinning method. For practical application of the stent graft to artificial blood vessels, the mechanical properties of the dimpled PET fiber should be clarified. In this study, the mechanical properties of single nanofibers and nonwoven fabrics of PET fibers with dimples on their surface were evaluated by tensile test. By forming the dimple shape on the fiber surface, the tensile strength of single PET fibers with dimples was 90 % lower than that of single PET fibers with a smooth surface. In the fabrication process of nonwoven fabric, the addition of EG delayed the volatilization of the PET solution, and the fibers adhered to each other. The bonding between the fibers contributed to the tensile strength of the nonwoven fabric.

scholarly journals Bending Behavior of Concrete Beams Using Geotextiles in Tensile Areas

2021 ◽  
Vol 3 (3) ◽  
pp. 412-420
Author(s):  
Sri Ponny ◽  
Jonie Tanijaya ◽  
Suryanti Rapang Tonapa
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Concrete Beams ◽  
Improve Quality ◽  
Puncture Resistance ◽  
Synthetic Fibers ◽  
Concrete Blocks ◽  
Bending Behavior ◽  
Test Objects ◽  
Tearing Strength

Geotextile is made of permeable geosynthetic. Geotextile s are formed from synthetic fibers based on polymers that have high mechanical properties in tensile strength, trapezoidal tearing strength, and puncture resistance. Therefore, researchers want to increase the use of Geotextile as an added material in the tensile area of concrete blocks. The test objects used are 9 pieces of 150mm×150mm×600mm beams. The results of the research were that the addition of woven Geotextile s and non-woven Geotextile s on concrete blocks increased, for woven Geotextile s by 21.593% of beams without using Geotextile s and non-woven Geotextile s of 17.058% of beams without using Geotextile s. So the use of Geotextile s on concrete blocks can improve quality because the value of the flexural strength of beams using Geotextile s is greater than beams without using Geotextiles.

Processing Technique and Impact Resistance of Kevlar/FPET/LPET Protective Nonwoven Fabrics

2014 ◽  
Vol 910 ◽  
pp. 174-177 ◽  
Author(s):  
Ching Wen Lou ◽  
Shih Yu Huang ◽  
Jia Horng Lin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Melting Point ◽  
Impact Resistance ◽  
Nonwoven Fabric ◽  
Processing Technique ◽  
Raw Material ◽  
Nonwoven Fabrics ◽  
Material Sources ◽  
Wide Range

Nonwoven fabric technique has been extensively used because nonwoven fabrics can uses both filaments and staple fibers and have ease of processing, a wide range of raw material sources, and a short production. This study makes protective nonwoven fabrics with Kevlar fibers, flame retardant polyester (FPET) fibers, and low-melting-point polyester (LPET) fibers. The number of lamination layers of the nonwoven fabric is varied and examined to determine their influence on the mechanical properties of the protective nonwoven fabrics. The results of test show that tensile strength and bursting strength of the protective nonwoven fabrics increase as a result of the increased number of lamination layer.

Manufacturing Technique of Sound-Absorbent PET/TPU Composites

2011 ◽  
Vol 239-242 ◽  
pp. 1968-1971 ◽  
Author(s):  
Jia Horng Lin ◽  
Chia Chang Lin ◽  
Chao Chiung Huang ◽  
Ching Wen Lin ◽  
Kuan Hsun Su ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Melting Point ◽  
Sound Absorption ◽  
Absorption Rate ◽  
Optimum Parameter ◽  
Thermoplastic Polyurethane ◽  
Nonwoven Fabrics ◽  
Manufacturing Technique ◽  
Pet Fibers

Five testing matrixes were prepared to test with sound absorption, tensile strength, and thermal conductivity respectively. The low-melting-point (low-Tm) polyester (PET) fibers were blended with weight ratios (10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt %) with PET staples, forming the PET nonwoven fabrics. The thermoplastic polyurethane (TPU) was thermal bounded with the nonwoven fabrics with different lamination number to examine the sound absorption rate, creating the PET/ TPU composites. Afterward, four sets of samples – PET nonwoven fabrics and PET/ TPU composites with TPU films laminated on the front, in the middle, and on the rear of the composites, were compared. PET/ TPU composite with TPU film laminated in the middle exhibited the optimum sound absorption; moreover, 30 wt% was proved to be the optimum parameter of the low-Tm PET fibers for the PET/ TPU composites.

Preparation Techniques and Property Evaluations of Highly Air Permeable Needle-Punched Geotextiles

2015 ◽  
Vol 749 ◽  
pp. 278-281
Author(s):  
Jia Horng Lin ◽  
Jing Chzi Hsieh ◽  
Jin Mao Chen ◽  
Wen Hao Hsing ◽  
Hsueh Jen Tan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Service Life ◽  
Mechanical Strength ◽  
Pore Structure ◽  
Test Results ◽  
Needle Punching ◽  
Pet Fibers ◽  
Environmental Requirements ◽  
Preparation Techniques

Geotextiles are made of polymers, and their conjunction with different processes and materials can provide geotextiles with desirable characteristics and functions, such as filtration, separation, and drainage, and thereby meets the environmental requirements. Chemical resistant and mechanical strong polymers, including polyester (PET) and polypropylene (PP), are thus used to prolong the service life of the products made by such materials. This study proposes highly air permeable geotextiles that are made with different thicknesses and various needle punching speeds, and the influences of these two variables over the pore structure and mechanical properties are then examined. PET fibers, PP fibers, and recycled Kevlar fibers are blended, followed by being needle punched with differing spaces and speeds to form geotextiles with various thicknesses and porosities. The textiles are then evaluated for their mechanical strength and porosity. The test results show that a thickness of 4.5 cm and 1.5 cm demonstrate an influence on the tensile strength of the geotextiles, which is ascribed to the webs that are incompletely needle punched. However, the excessive needle punching speed corresponding to a thickness of 0.2 cm results in a decrease in tensile strength, but there is also an increase in the porosity of the geotextiles.

scholarly journals A Study on the Entanglement and High-Strength Mechanism of Spunlaced Nonwoven Fabric of Hydrophilic PET Fibers

2013 ◽  
Vol 8 (4) ◽  
pp. 155892501300800 ◽  
Author(s):  
Hong Wang ◽  
Jingjing Zhu ◽  
Xiangyu Jin ◽  
Haibo Wu
Keyword(s):  
Tensile Strength ◽  
High Strength ◽  
Nonwoven Fabric ◽  
Fiber Content ◽  
Nonwoven Fabrics ◽  
Pull Out ◽  
Fundamental Research ◽  
Pet Fibers ◽  
Set Up

Spunlaced nonwoven fabrics have been widely used recently, but fundamental research on the spunlaced nonwoven process is relatively weak. It is inexplicit until now how fibers are entangled with each other during the hydroentangling process. In this paper, a pull-out experiment designed to study the entanglement properties of spunlaced nonwoven fabrics using common and hydrophilic PET fibers as objects is described. It was found that the broken fiber content can be used to represent the entanglement intensity of the spunlaced nonwoven fabrics. In addition, a formula was set up to calculate the tensile strength of the spunlaced nonwoven fabric based on its pull-out behavior.

EXPERIMENTAL STUDY ON MECHANICAL PROPERTIES OF MAGNETORHEOLOGICAL ELASTOMER

2016 ◽  
Vol 78 (5-4) ◽  
Author(s):  
Nurul Husna Rajhan ◽  
Hanizah Ab. Hamid ◽  
Azmi Ibrahim ◽  
Rozaina Ismail
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Carbon Black ◽  
Tensile Test ◽  
Magnetorheological Elastomer ◽  
Dead Load ◽  
Carbon Black Content ◽  
Engineering Applications ◽  
Magnetorheological Elastomers

Magnetorheological elastomers (MREs) have much interest in engineering applications. However, the mechanical properties of MREs are still under ongoing researches. This paper presents the results from tensile test, hardness and rebound test that were carried out in order to understand the mechanical properties of MRE with the influence of carbon black content. The addition of carbon black was varied with the amount of 20 pphr, 40 pphr and 60 pphr of carbon black. The development of the MRE composites was manufactured by following the conventional rubber compounding process. The optimum cure of each MRE composite was determined by using a Rheometer 100. The mechanical properties through tensile test were obtained by using an Instron Tensile Machine, meanwhile hardness and resilience were carried out by using Wallace Dead Load Hardness and Dunlop Tripsometer, respectively. The results of tensile strength were not consistent with the addition of carbon black. In meantime, hardness value increases as the carbon black increases. The decreasing pattern of MRE resilience could be observed when the carbon black content increases.

scholarly journals Influence of Drying Temperature on Tensile and Bursting Strength of Bacterial Cellulose Biofilm

2019 ◽  
Vol 25 (3) ◽  
pp. 316-321
Author(s):  
Florentina SEDERAVIČIŪTĖ ◽  
Jurgita DOMSKIENĖ ◽  
Ilze BALTINA
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Strength Properties ◽  
Drying Temperature ◽  
Bursting Strength ◽  
Bacterial Fermentation ◽  
Deformation Properties ◽  
C 50 ◽  
Material Preparation

The article presents an experimental study of mechanical properties of cellulose biofilm produced by bacterial fermentation process. Naturally derived biomaterial has great current and potential applications therefore the conditions of material preparation as well as control and prediction of mechanical properties is still a relevant issue. Bacterial cellulose was obtained as a secondary product from Kombucha drink. Presented technique for material preparation and drying is particularly simple and easy to access. The influence of drying temperature (25 °C, 50 °C and 75 °C) on the sample size (thickness and planar dimensions) and mechanical properties (tensile and bursting strength) of cellulose biofilm has been evaluated. It was estimated that during drying biofilm specimens lost up to 92 % of weight and up to 87 % of thickness therefore planar specimen dimensions varied insignificantly. The study showed that the drying temperature is important for optimum strength properties of bacterial cellulose biofilm. The maximum tensile strength (27.91 MPa) was recorded for the samples dried at temperature of 25 °C, when the moisture from the biomaterial is removed gradually and good deformation properties are ensured (respectively tensile extension 18.8 %). Under higher drying temperature biomaterial shows lower values of tensile strength and higher values of bursting strength. The maximum bursting strength (57.2 MPa) was recorded for samples dried at 75 °C when punch displacement changes were insignificant for all tested samples (from 17.8 mm to 21.7 mm). DOI: http://dx.doi.org/10.5755/j01.ms.25.3.20764

Affection of Manufacture Parameters and Mixture Material on Plastic Alloy Bearings

2012 ◽  
Vol 164 ◽  
pp. 37-41
Author(s):  
Cheng Yun Yang ◽  
Jin Min Peng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Process Parameters ◽  
Peel Strength ◽  
Manufacture Process ◽  
Orthogonal Experiments ◽  
And Performance ◽  
Orthogonal Tests ◽  
Tearing Strength ◽  
Optimal Formula

Manufacture process parameters will be obtained from experiments in research. Molding technology determines the mechanical properties and performance of the product. The influence of molding temperature and time are significant on the performance of water lubricated bearing, the plastic alloy is based on latex material, synthesized with different fillings, accelerators and other matters, and displays great mechanical and friction properties. The main performance included peel strength, tensile strength and wearing capacity. Optimization of manufacture process parameters and the orthogonal experiments on them were carried out by integrating the results of experiments and finally the optimal manufacture process was achieved. In the experiment, three-leveled orthogonal tests were conducted for the three systems to test the tensile strength, tearing strength, stress at definite elongation, hardness and tensile rate. The impacts of the respective systems were analyzed and the content of each component are determined to get the optimal formula.

Sign in / Sign up

Export Citation Format

Share Document