Effect of Vanadium Addition to Aluminum and Aluminum Grain Refined by Titanium on their Chemical Corrosion Rate in Acidic Solution, HCL, at Different Temperatures

2012 ◽  
Vol 510-511 ◽  
pp. 481-486
Author(s):  
A.I.O. Zaid ◽  
G.T.A. Allawi ◽  
A. Al-Haj-Ali
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Rate ◽  
Acidic Solution ◽  
Chemical Corrosion ◽  
Different Temperatures

The paper presents the effect of vanadium addition to aluminum and aluminum grain refined by titanium on the micron level, in the range from 0.005 wt % to 0.236 wt %, on their corrosion resistance in acidic solution, HCl, at three different temperatures namely: 25 °C, 40 °C and 60 °C. It was found that the corrosion rate was slightly increased by the addition of any percentage of vanadium at 25 °C. Furthermore, it was found that the corrosion rate increased with the increase of temperature at any percentage of vanadium addition in the case of both aluminum and aluminum grain refined by titanium. However it was found that addition of vanadium at any percentage to either aluminum or aluminum+ titanium, resulted in decrease of the corrosion rate i.e. improvement in their corrosion resistance in acidic solution at 40 °C and 60 °C. The maximum achieved reduction in corrosion rate was 77 % at 40 °C and 0.148 wt % vanadium addition.

Corrosion Behavior of WC-Co and WC-Ni in 3.5% NaCl at Increasing Temperature

2014 ◽  
Vol 660 ◽  
pp. 135-139 ◽  
Author(s):  
A. Ismail ◽  
Norhaslina Abd Aziz
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Rate ◽  
Tungsten Carbide ◽  
Surface Structure ◽  
Tungsten Carbides ◽  
Corrosion Performance ◽  
Corrosion Attack ◽  
Different Temperatures ◽  
Increasing Temperature ◽  
Nickel Tungsten

Tungsten carbides (WC) are widely used as wear resistant components such as seal, valves, rings, nozzle and bearings. But in some processing operations, the environment necessarily includes severe corrosion or extremes of temperatures. In paper reveal, the corrosion performance of commercial cobalt tungsten carbide (WC-6%Co) and nickel tungsten carbide (WC-9%Ni) in seawater with 3.5% salinity. The experiment was performed in four different temperatures (20°C, 40°C, 60°C and 80°C) and the surface structure by corrosion attack was reveal under SEM. TheIcorrvalue of WC-9%Ni is lower than WC-6%Co, elucidate that WC-9%Ni is better in corrosion resistance compare to WC-6%Co. As the temperature increased, the corrosion rate for every material increased as expected. Decreasing in hardness value for both materials reveal that, the material’s hardness decrease after corrosion has attacked.

Effect of Solution Treatment on Corrosion Resistance of the Biodegradable NZ20K Alloy

2016 ◽  
Vol 849 ◽  
pp. 196-202
Author(s):  
Yang Fei ◽  
Xiao Bo Zhang ◽  
Zhi Xin Ba ◽  
Zhang Zhong Wang
Keyword(s):  
Corrosion Resistance ◽  
Electron Microscope ◽  
Corrosion Rate ◽  
Scanning Electron Microscope ◽  
Biomedical Applications ◽  
Solution Treatment ◽  
Solution Temperature ◽  
Solution Treated ◽  
Different Temperatures ◽  
Scanning Electron

In order to study the effect of solution temperature on corrosion resistance of Mg alloy for biomedical applications, microstructure and corrosion behavior of Mg-2.25Nd-0.11Zn-0.43Zr (NZ20K) alloy solution treated at different temperatures were investigated by using a scanning electron microscope (SEM) equipped with an electron dispersive spectroscope (EDS), electrochemical and mass loss tests. The results show that the grains grow and precipitations decreases with increasing the solution temperature. The corrosion rate decreases firstly and then increases with increasing solution temperature, and the best corrosion resistance of the NZ20K alloy is obtained at the temperature of 540 °C.

Effect of Elemental Sulfur on Corrosion Behavior of Super 13Cr Martensitic Stainless Steel

2014 ◽  
Vol 556-562 ◽  
pp. 162-165 ◽  
Author(s):  
Shi Dong Zhu ◽  
Hai Xia Ma ◽  
Jin Ling Li ◽  
Zhi Gang Yang
Keyword(s):  
Weight Loss ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Corrosion Rate ◽  
Corrosion Behavior ◽  
Elemental Sulfur ◽  
Martensitic Stainless Steel ◽  
Chemical Elements ◽  
Different Temperatures ◽  
Corrosion Scales

Effects of elemental sulfur on corrosion behavior of super 13Cr martensitic stainless steel were investigated by utilizing weight loss test, and the micro morphologies and chemical elements of corrosion scales were characterized by using SEM and EDS. The results showed that corrosion resistance of super 13Cr stainless steel was aggravated by the hydrolytic action of sulfur, the corrosion rate of super 13Cr stainless steel increased with the increasing of sulfur content, and firstly increased and then decreased with the increasing of temperature due to the activated adsorption and existential state of sulfur at the different temperatures.

scholarly journals Influence of Aging Heat Treatment on Pitting Corrosion Resistance of Martensitic Stainless Steel

2021 ◽  
Vol 17 (1) ◽  
pp. 20-33
Author(s):  
Abdullah Dhayea Assi
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Corrosion Rate ◽  
Pitting Corrosion ◽  
Corrosion Test ◽  
Martensitic Stainless Steel ◽  
Aging Heat Treatment ◽  
Chemical Corrosion ◽  
Pitting Corrosion Resistance

In this research is to study the influence of the aging heat treatment on the pitting corrosion resistance of martensitic stainless steel (MSS), where a number of specimens from martensitic stainless steel were subjected to solution treatment at 1100 oC for one hour followed by water quenching then aging in the temperatures range (500-750) oC for different holding times (1,5,10,15&20) hr. Accelerated chemical corrosion test and immersion chemical corrosion test were performed on samples after heat treatment. The results of the research showed that the pitting corrosion resistance is significantly affected by the aging temperature. Where found that the aging samples at a temperature of 500 °C have the highest rate of corrosion which may be due to an increase in the ratio of the Delta type ferrite (δ-ferrite) and very soft precipitates from other phases of heterogeneous form in the basic martensitic phase; which leads to increased corrosion rate, whereas aging   samples in the temperature range (550–650) °C have the smaller rate of corrosion values, this is due to the high volumetric ratio of remaining austenite. The aging samples at temperatures above 650 °C show an average corrosion rate. It was also found that the type of pits resulting from both the chemical corrosion tests and their shape were not related to the ferrite type and the carbides present in the microstructure

COOPER ALLOY 22W

Alloy Digest ◽  
1963 ◽  
Vol 12 (8) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Creep Rate ◽  
Corrosion Rate ◽  
Physical Properties ◽  
High Strength ◽  
Heat Treating ◽  
Casting Alloy ◽  
Hot Gas ◽  
Gas Corrosion ◽  
Very High

Abstract Cooper Alloy 22W is a high strength, heat resistant casting alloy with a low creep rate. It is recommended for heat applications where stress and hot gas corrosion rate are very high. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as casting, heat treating, machining, joining, and surface treatment. Filing Code: SS-146. Producer or source: Cooper Alloy Corporation.

Heat Treatment Influence on the Corrosion Resistance of a Cu-Al-Fe-Mn Bronze

2018 ◽  
Vol 69 (5) ◽  
pp. 1055-1059 ◽  
Author(s):  
Mariana Ciurdas ◽  
Ioana Arina Gherghescu ◽  
Sorin Ciuca ◽  
Alina Daniela Necsulescu ◽  
Cosmin Cotrut ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Structural Changes ◽  
Heating Temperature ◽  
Galvanic Corrosion ◽  
Cooling Water ◽  
Open Circuit ◽  
Water Quenching ◽  
Heat Treated ◽  
Different Temperatures

Aluminium bronzes are exhibiting good corrosion resistance in saline environments combined with high mechanical properties. Their corrosion resistance is obviously confered by the alloy chemical composition, but it can also be improved by heat treatment structural changes. In the present paper, five Cu-Al-Fe-Mn bronze samples were subjected to annealing heat treatments with furnace cooling, water quenching and water quenching followed by tempering at three different temperatures: 200, 400 and 550�C. The heating temperature on annealing and quenching was 900�C. The structure of the heat treated samples was studied by optical and scanning electron microscopy. Subsequently, the five samples were submitted to corrosion tests. The best resistance to galvanic corrosion was showed by the quenched sample, but it can be said that all samples are characterized by close values of open-circuit potentials and corrosion potentials. Concerning the susceptibility to other types of corrosion (selective leaching, pitting, crevice corrosion), the best corrosion resistant structure consists of a solid solution, g2 and k compounds, corresponding to the quenched and 550�C tempered sample.

Effect of Electrolyte Composition on Corrosion Resistance in Nickel Plating Process for Coating Bonded Magnet PrFeB

2014 ◽  
Vol 896 ◽  
pp. 245-248 ◽  
Author(s):  
Candra Kurniawan ◽  
Hayati M.A. Sholihat ◽  
Kemas Ahmad Zaini Thosin ◽  
Muljadi ◽  
Prijo Sardjono
Keyword(s):  
Magnetic Properties ◽  
Corrosion Resistance ◽  
Corrosion Rate ◽  
Nickel Coating ◽  
Electrolyte Composition ◽  
Nickel Metal ◽  
Sem Images ◽  
Average Value ◽  
Immersion Corrosion ◽  
Bonded Magnet

Despite of its excellence magnetic quality, one of the critical properties of PrFeB based permanent magnet is a low corrosion resistance so it can be oxidized easily which can reduce its magnetic properties. In this study, Nickel coating has been performed for bonded PrFeB magnet by the electroplating method using Nickel-Watts bath-type as the electrolyte to improve the corrosion resistance. The varying amount of the electrolyte compounds used to have the optimized composition indicated by the corrosion resistance measurement. The solution composition used was NiSO4 (230-380 g/L), NiCl2 (30-60 g/L), and H3BO3 (30 and 45 g/L) with a fixed value of other parameters. Characterization used including the immersion corrosion test, microstructure analysis, and magnetic properties. Based on the corrosion rate measurement, the highest corrosion resistant of Nickel coated PrFeB magnet achieved from the electrolyte composition of NiSO4: NiCl2: H3BO3 = 380: 60: 30 g/L with a plating time and current density (J) of 60 minutes and 40 mA/cm2 respectively. The corrosion rate data showed that the Nickel metal coating can improve the corrosion resistance of bonded PrFeB magnet up to 29 times than of the substrate. The SEM images showed that the thickness of the Nickel coating on the optimum electrolyte composition was in average value of 35.1 µm. The overall samples has a magnetic remanence value (Br) reached ≥ 6 kG, so it has enough properties to be applied in devices such as generators and electric motors.

scholarly journals Effect of Mn Content and Solution Annealing Temperature on the Corrosion Resistance of Stainless Steel Alloys

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Ihsan-ul-Haq Toor
Keyword(s):  
Corrosion Resistance ◽  
Annealing Temperature ◽  
Electrochemical Impedance ◽  
Austenitic Stainless Steels ◽  
Electrochemical Tests ◽  
Linear Polarization Resistance ◽  
Ni Content ◽  
Different Temperatures ◽  
Acidic Chloride ◽  
Mn Content

The corrosion behavior of two specially designed austenitic stainless steels (SSs) having different Nickel (Ni) and Manganese (Mn) contents was investigated. Prior to electrochemical tests, SS alloys were solution-annealed at two different temperatures, that is, at 1030°C for 2 h and 1050°C for 0.5 h. Potentiodynamic polarization (PD) tests were carried out in chloride and acidic chloride, whereas linear polarization resistance (LPR) and electrochemical impedance spectroscopy (EIS) was performed in 0.5 M NaCl solution at room temperature. SEM/EDS investigations were carried out to study the microstructure and types of inclusions present in these alloys. Experimental results suggested that the alloy with highest Ni content and annealed at 1050°C/0.5 hr has the highest corrosion resistance.

scholarly journals Wear and Corrosion of Wrought A6061 Aluminium Alloy in DOT3 Brake Fluid

2018 ◽  
Vol 7 (2.14) ◽  
pp. 512 ◽  
Author(s):  
Olawale Ajibola ◽  
Oladeji Ige ◽  
Peter Olubambi
Keyword(s):  
Corrosion Rate ◽  
Test Method ◽  
Alloy Sample ◽  
Corrosive Media ◽  
Chemical Corrosion ◽  
Brake Fluid ◽  
Wear And Corrosion ◽  
Cast Specimen ◽  
Fluid Environment ◽  
A6061 Alloy

The twofold impact of wear and corrosion on wrought A6061 alloy in hydraulic DOT3 brake fluid environment was studied. The wear studies were performed on the samples using a developed wear-jig. Weight loss corrosion test method was used to determine the corrosion rate of the wrought A6061 alloy samples immersed in the brake fluid for a total of 1680 hours. From the results of wear tests carried out on the A6061 alloy sample with brake oil, the highest wear value of 5.24x10-7 mg/mm2/cycle (approx.) was obtained from 6 N (approx) force after 130 minutes. The wrought A6061 alloy material demonstrated the highest corrosion rates nearly 3.0 x10-2 mg/mm2/yr within the early 168 hours of immersion in brake fluid. The result is practically lower than the corrosion rate of cast specimen in DOT3 brake oil or some other alloys immersed in other corrosive media that were previously reported in the literature. The results show that small amount of chemical corrosion is sufficient to cause and accelerate mechanical wear of the material in usage.

scholarly journals Effects of tungsten, chromium and zirconium on the corrosion behavior of ternary amorphous W–Cr–Zr alloys in 1 M NaOh solution

1970 ◽  
Vol 9 (9) ◽  
pp. 39-43
Author(s):  
Basu Ram Aryal ◽  
Jagadeesh Bhattarai
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Rate ◽  
Open Circuit Potential ◽  
Open Circuit ◽  
Corrosion Rates ◽  
Corrosion Resistance Property ◽  
Naoh Solution ◽  
Order Of Magnitude ◽  
Sputter Deposited ◽  
Zr Alloys

Simultaneous additions of tungsten, chromium and zirconium in the chromium- and zirconium-enriched sputter-deposited binary W-xCr and W-yZr are effective to improve the corrosion resistance property of the ternary amorphous W- xCr-yZr alloys after immersion for 240 h in 1 M NaOH solution open to air at 25°C. The corrosion rates of all the examined sputter-deposited (10-57)W-(18-42)Cr-(25-73)Zr alloys is higher than those of alloy-constituting elements (that is, tungsten, chromium and zirconium) in aggressive 1 M NaOH solution open to air at 25°C. The corrosion rates of all the examined sputter−deposited W–xCr–yZr alloys containing 10-57 at% tungsten, 18-42 at% chromium and 25-73 at% zirconium were in the range of 1.5-2.5 × 10−3 mm/y or lower which are more than two orders of magnitude lower than that of sputter-deposited tungsten and even about one order of magnitude lower than those of the sputter-deposited zirconium in 1 M NaOH solution. Keywords: Ternary W–Cr–Zr alloys; Amorphous; Corrosion rate; Open circuit potential; 1 M NaOH. DOI: http://dx.doi.org/10.3126/sw.v9i9.5516 SW 2011; 9(9): 39-43

Sign in / Sign up

Export Citation Format

Share Document