Investigation of Deformation Induced Martensitic Transformation during Incremental Forming of 304 Stainless Steel Wires

2015 ◽  
Vol 651-653 ◽  
pp. 645-650 ◽  
Author(s):  
Bernd Kuhfuss ◽  
Eric Moumi ◽  
Brigitte Clausen ◽  
Jeremy Epp ◽  
Bernd Koehler
Keyword(s):  
Volume Fraction ◽  
Processing Parameters ◽  
304 Stainless Steel ◽  
Strain Rates ◽  
X Ray Diffraction ◽  
Forming Process ◽  
Cold Forming ◽  
X Ray ◽  
Steel Wires ◽  
Different Temperatures

Wires with 1 mm initial diameter have been reduced between 10 and 64 percent at different temperatures and strain rates by infeed rotary swaging, which is an incremental cold forming process mainly used for rods and pipes. The volume fraction of martensite in the deformed wires has been determined by X-Ray diffraction and by magnetic induction for different processing parameters. Measurements show that for already small percentage of reduction, martensite is present in the wires and its amount changes with the strain rate and temperature. While for smaller strain rates at room temperature the formation of martensite is promoted, it is restrained for higher strain rates and higher temperatures. Results also reveal that the martensite distribution in the sample is inhomogeneous. Further investigations have been made to analyze the microstructure by optical microscopy and to determine mechanical properties by tensile testing.

Preparation and Property of Al87Ce3Ni8.5Mn1.5 Nanophase Amorphous Composites

2011 ◽  
Vol 412 ◽  
pp. 263-266
Author(s):  
Hong Wei Zhang ◽  
Li Li Zhang ◽  
Feng Rui Zhai ◽  
Jia Jin Tian ◽  
Can Bang Zhang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Single Phase ◽  
Volume Fraction ◽  
Material Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures

The higher mechanical strength of Al87Ce3Ni8.5Mn1.5 nanophase amorphous composites has been obtained with two methods. The first nanophase amorphous composites are directly produced by the single roller spin quenching technology. The method taken for the second nanophase amorphous composites is at first to obtain amorphous single-phase alloy, followed by annealed at different temperatures .The formative condition, the microstructure, the particle size, the volume fraction of α-Al phase and microhardness of nanophase amorphous composites etc have been investigated and compared by X-ray diffraction (XRD) and transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The microstructure of composites produced by the second method is higher than the former, the fabricated material structure of the system is more uniform and the process is easier to control.

scholarly journals Role of the extra Fe in K2−xFe4+ySe5 superconductors

2019 ◽  
Vol 116 (4) ◽  
pp. 1104-1109 ◽  
Author(s):  
Chih-Han Wang ◽  
Chih-Chien Lee ◽  
Gwo-Tzong Huang ◽  
Jie-Yu Yang ◽  
Ming-Jye Wang ◽  
...  
Keyword(s):  
Volume Fraction ◽  
Parent Compound ◽  
Superconducting Transition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Different Temperatures ◽  
Two Phases ◽  
Best Fit

The exact superconducting phase of K2−xFe4+ySe5 has so far not been conclusively decided since its discovery due to its intrinsic multiphase in early material. In an attempt to resolve this mystery, we have carried out systematic structural studies on a set of well-controlled samples with exact chemical stoichiometry K2−xFe4+xSe5 (x = 0–0.3) that are heat-treated at different temperatures. Using high-resolution synchrotron radiation X-ray diffraction, our investigations have determined the superconducting transition by focusing on the detailed temperature evolution of the crystalline phases. Our results show that superconductivity appears only in those samples that have been treated at high-enough temperature and then quenched to room temperature. The volume fraction of superconducting transition strongly depends on the annealing temperature used. The most striking result is the observation of a clear contrast in crystalline phase between the nonsuperconducting parent compound K2Fe4Se5 and the superconducting K2−xFe4+ySe5 samples. The X-ray diffraction patterned can be well indexed to the phase with I4/m symmetry in all temperatures investigated. However, we need two phases with similar I4/m symmetry but different parameters to best fit the data at a temperature below the Fe vacancy order temperature. The results strongly suggest that superconductivity in K2−xFe4+ySe5 critically depends on the occupation of Fe atoms on the originally empty 4d site.

scholarly journals A Superhydrophobic, Antibacterial, and Durable Surface of Poplar Wood

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1885
Author(s):  
Xinyu Wu ◽  
Feng Yang ◽  
Jian Gan ◽  
Zhangqian Kong ◽  
Yan Wu
Keyword(s):  
Stearic Acid ◽  
Antibacterial Properties ◽  
Alkali Resistance ◽  
Poplar Wood ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Acid And Alkali Resistance ◽  
The Stability

The silver particles were grown in situ on the surface of wood by the silver mirror method and modified with stearic acid to acquire a surface with superhydrophobic and antibacterial properties. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and X-ray energy spectroscopy (XPS) were used to analyze the reaction mechanism of the modification process. Scanning electron microscopy (SEM) and contact angle tests were used to characterize the wettability and surface morphology. A coating with a micro rough structure was successfully constructed by the modification of stearic acid, which imparted superhydrophobicity and antibacterial activity to poplar wood. The stability tests were performed to discuss the stability of its hydrophobic performance. The results showed that it has good mechanical properties, acid and alkali resistance, and UV stability. The durability tests demonstrated that the coating has the function of water resistance and fouling resistance and can maintain the stability of its hydrophobic properties under different temperatures of heat treatment.

scholarly journals Statistical analysis of the reproducibility of residual stress measurements in cold extruded parts

2021 ◽  
Author(s):  
Fabian Jaeger ◽  
Alessandro Franceschi ◽  
Holger Hoche ◽  
Peter Groche ◽  
Matthias Oechsner
Keyword(s):  
Residual Stress ◽  
Statistical Analysis ◽  
Stress Measurement ◽  
Industrial Applications ◽  
Cold Extrusion ◽  
X Ray Diffraction ◽  
Forming Process ◽  
X Ray ◽  
Stress States ◽  
Key Aspects

AbstractCold extruded components are characterized by residual stresses, which originate from the experienced manufacturing process. For industrial applications, reproducibility and homogeneity of the final components are key aspects for an optimized quality control. Although striving to obtain identical deformation and surface conditions, fluctuation in the manufacturing parameters and contact shear conditions during the forming process may lead to variations of the spatial residual stress distribution in the final product. This could lead to a dependency of the residual stress measurement results on the relative axial and circumferential position on the sample. An attempt to examine this problem is made by the employment of design of experiments (DoE) methods. A statistical analysis of the residual stress results generated through X-Ray diffraction is performed. Additionally, the ability of cold extrusion processes to generate uniform stress states is analyzed on specimens of austenitic stainless steel 1.4404 and possible correlations with the pre-deformed condition are statistically examined. Moreover, the influence of the coating, consisting of oxalate and a MoS2 based lubricant, on the X-Ray diffraction measurements of the surface is investigated.

scholarly journals Effect of the γ→ε Phase Transition on Transformation-Induced Plasticity (TRIP) of Nickel-Free High Nitrogen Steel at Low Temperatures

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 710
Author(s):  
Natalia Narkevich ◽  
Yevgeny Deryugin ◽  
Yury Mironov
Keyword(s):  
Volume Fraction ◽  
Tensile Load ◽  
X Ray Diffraction ◽  
High Nitrogen Steel ◽  
Transformation Induced Plasticity ◽  
X Ray ◽  
Root Cause ◽  
Nitrogen Steel ◽  
Ε Phase ◽  
Ε Martensite

The deformation behavior, mechanical properties, and microstructure of Fe-Cr-Mn-0.53%N austenitic stainless steel were studied at a temperature range of 77 up to 293 K. The dynamics of the steel elongation were non-monotonic with a maximum at 240–273 K, when peaks of both static atom displacements from their equilibrium positions in austenite and residual stresses in the tensile load direction were observed. The results of X-ray diffraction analysis confirmed that the only stress-induced γ→ε-martensite transformation occurred upon deformation (no traces of the γ→α′ one was found). In this case, the volume fraction of ε-martensite was about 2–3%. These transformation-induced plasticity (TRIP) patterns were discussed in terms of changes in the phase composition of steel as the root cause.

scholarly journals Hydrothermal Ageing and Its Effect on Fracture Load of Zirconia Dental Implants

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3103
Author(s):  
Laurent Gremillard ◽  
Agnès Mattlet ◽  
Alexandre Mathevon ◽  
Damien Fabrègue ◽  
Bruno Zberg ◽  
...  
Keyword(s):  
Dental Implants ◽  
Fracture Load ◽  
Accelerated Ageing ◽  
Dental Ceramics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dental Restorations ◽  
Different Temperatures ◽  
Mechanical Performances ◽  
Kinetics Of

Due to growing demand for metal-free dental restorations, dental ceramics, especially dental zirconia, represent an increasing share of the dental implants market. They may offer mechanical performances of the same range as titanium ones. However, their use is still restricted by a lack of confidence in their durability and, in particular, in their ability to resist hydrothermal ageing. In the present study, the ageing kinetics of commercial zirconia dental implants are characterized by X-ray diffraction after accelerated ageing in an autoclave at different temperatures, enabling their extrapolation to body temperature. Measurements of the fracture loads show no effect of hydrothermal ageing even after ageing treatments simulated a 90-year implantation.

scholarly journals Modeling of magneto-conductivity of bismuth selenide: a topological insulator

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Yogesh Kumar ◽  
Rabia Sultana ◽  
Prince Sharma ◽  
V. P. S. Awana
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Single Crystal ◽  
Single Crystals ◽  
X Ray Diffraction ◽  
Field Range ◽  
X Ray ◽  
Bulk Carriers ◽  
Different Temperatures

AbstractWe report the magneto-conductivity analysis of Bi2Se3 single crystal at different temperatures in a magnetic field range of ± 14 T. The single crystals are grown by the self-flux method and characterized through X-ray diffraction, Scanning Electron Microscopy, and Raman Spectroscopy. The single crystals show magnetoresistance (MR%) of around 380% at a magnetic field of 14 T and a temperature of 5 K. The Hikami–Larkin–Nagaoka (HLN) equation has been used to fit the magneto-conductivity (MC) data. However, the HLN fitted curve deviates at higher magnetic fields above 1 T, suggesting that the role of surface-driven conductivity suppresses with an increasing magnetic field. This article proposes a speculative model comprising of surface-driven HLN and added quantum diffusive and bulk carriers-driven classical terms. The model successfully explains the MC of the Bi2Se3 single crystal at various temperatures (5–200 K) and applied magnetic fields (up to 14 T).

Effect of the BSCCO superconducting properties by tiny Y2O3 addition

2016 ◽  
Vol 30 (26) ◽  
pp. 1650328
Author(s):  
Yan Dong ◽  
Aimin Sun ◽  
Bin Xu ◽  
Hongtao Zhang ◽  
Meng Zhang
Keyword(s):  
Volume Fraction ◽  
Superconducting Properties ◽  
X Ray Diffraction ◽  
Critical Transition Temperature ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Oxide Addition ◽  
One Step ◽  
Step Transition ◽  
Y2o3 Addition

In this paper, the effect of tiny Y2O3 addition in (Bi,[Formula: see text]Pb)-2223 superconductor prepared by solid state reaction technique was studied. The properties of samples have been investigated via X-ray diffraction (XRD), resistance–temperature ([Formula: see text]–[Formula: see text]) curve, scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS). XRD data indicated that all samples are multiphase and the major phases are high-temperature phases and low-temperature phases. The volume fraction of (Bi,[Formula: see text]Pb)-2223 is not great change with tiny Y2O3 addition. All samples exhibit superconducting phase with the critical transition temperature and one-step transition, however, the transition width was decreased with the Y2O3 addition up to 0.04 wt.% and sharp increased with the excessive oxide addition. SEM pictures show that the Y2O3 appeared on the flake-type grains surface obviously, but the number and size of the hole between grains are decreased in the 0.04 wt.% addition.

scholarly journals Multiscale Copper-µDiamond Nanostructured Composites

2012 ◽  
Vol 730-732 ◽  
pp. 925-930
Author(s):  
Daniela Nunes ◽  
Vanessa Livramento ◽  
Horácio Fernandes ◽  
Carlos Silva ◽  
Nobumitsu Shohoji ◽  
...  
Keyword(s):  
Pure Copper ◽  
Thermal Stabilization ◽  
Hot Extrusion ◽  
Processing Parameters ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Optimal Processing ◽  
Novel Approach ◽  
Transmission Electron

Nanostructured copper-diamond composites can be tailored for thermal management applications at high temperature. A novel approach based on multiscale diamond dispersions is proposed for the production of this type of materials: a Cu-nDiamond composite produced by high-energy milling is used as a nanostructured matrix for further dispersion of micrometer sized diamond. The former offers strength and microstructural thermal stability while the latter provides high thermal conductivity. A series of Cu-nDiamond mixtures have been milled to define the minimum nanodiamond fraction suitable for matrix refinement and thermal stabilization. A refined matrix with homogenously dispersed nanoparticles could be obtained with 4 at.% nanodiamond for posterior mixture with mDiamond and subsequent consolidation. In order to define optimal processing parameters, consolidation by hot extrusion has been carried out for a Cu-nDiamond composite and, in parallel, for a mixture of pure copper and mDiamond. The materials produced were characterized by X-ray diffraction, scanning and transmission electron microscopy and microhardness measurements.

A Study on Nanocrystalline Nickel Parts Prepared by Jet Electrodeposition

2010 ◽  
Vol 37-38 ◽  
pp. 64-67
Author(s):  
Jin Song Chen ◽  
Yin Hui Huang ◽  
Bin Qiao ◽  
Jian Ming Yang ◽  
Yi Qiang He
Keyword(s):  
Dimensional Accuracy ◽  
Processing Parameters ◽  
X Ray Diffraction ◽  
Scanning Microscope ◽  
Nanocrystalline Nickel ◽  
X Ray ◽  
Fine Grained ◽  
Average Grain Size ◽  
Jet Electrodeposition ◽  
Fine Grained Structure

The principles of jet electrodeposition orientated by rapid prototyping were introduced. The nanocrystalline nickel parts with simple shape were fabricated using jet electrodeposition. The microstructure and phase transformation of nanocrystalline nickel were observed under the scanning microscope and X-ray diffraction instrument. The results show that the jet electrodeposition can greatly enhance the limited current density, fine crystalline particles and improve deposition quality. The nickel parts prepared by jet electrodeposition own a fine-grained structure (average grain size 25.6nm) with a smooth surface and high dimensional accuracy under the optimum processing parameters.

Sign in / Sign up

Export Citation Format

Share Document