Synthesis of Diamond on SiC by Microwave Plasma Chemical Vapor Deposition: Comparison of Silicon-Face and Carbon-Face

2020 ◽  
Vol 1014 ◽  
pp. 8-13
Author(s):  
Xue Min Zhang ◽  
Chang Ling Yan ◽  
Chun Hong Zeng ◽  
Yi Qun Wang ◽  
Bao Shun Zhang ◽  
...  

Diamond is arguably the best candidate material for heat dissipation applications, especially in high-power electronic devices. Silicon carbide (SiC) is a kind of wide band gap material, which can be used in applications of silicon (Si) components to reach the performance limits. In this paper, thin diamond films were successfully deposited on C-face and Si-face of 6H-SiC substrates respectively using MPCVD at temperatures from 800 to 1050 °C. SEM images indicated the growth quality comparison of the two faces of SiC. The diffraction peaks of the diamond (111), (220), and (311) crystal planes can be observed by XRD measurement, and the intensity of the diamond diffraction peaks grown on the C-face is stronger than that on Si-face. The growth process was analyzed by Raman spectrum. FWHM of diamond Raman spectra on Si-face and C-face are 6.07cm-1 and 5.47cm-1 respectively. All above measurement results show that the diamond grown on the C-face has higher crystal quality than that on Si-face of SiC.

Shinku ◽  
1997 ◽  
Vol 40 (8) ◽  
pp. 660-663
Author(s):  
Hideo OKAYAMA ◽  
Tsukasa KUBO ◽  
Noritaka MOCHIZUKI ◽  
Akiyoshi NAGATA ◽  
Hiromu ISA

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 888
Author(s):  
Pengfei Zhang ◽  
Weidong Chen ◽  
Longhui Zhang ◽  
Shi He ◽  
Hongxing Wang ◽  
...  

In this paper, we successfully synthesized homoepitaxial diamond with high quality and atomically flat surface by microwave plasma chemical vapor deposition. The sample presents a growth rate of 3 μm/h, the lowest RMS of 0.573 nm, and the narrowest XRD FWHM of 31.32 arcsec. An effect analysis was also applied to discuss the influence of methane concentration on the diamond substrates.


2011 ◽  
Vol 117-119 ◽  
pp. 1310-1314
Author(s):  
Xing Rui Li ◽  
Xin Wei Shi ◽  
Ning Yao ◽  
Xin Chang Wang

Nano-crystalline diamond (NCD) films with good adhesion were deposited on flexible copper substrate with Ni interlayer by Microwave Plasma Chemical Vapor Deposition (MPCVD). In this paper, two-stage method was used to improve the adhesion between the copper substrates and the diamond films. The effect of deposition time of the first stage on the morphology, crystal structure, non-diamond phase and adhesive properties of diamond films was investigated. The performance and structure of the diamond films were studied by Scanning Electron Microscope (SEM), Raman Spectroscopy (Raman) and X-Ray Diffraction (XRD). The results showed that the films were nano-crystalline diamond films positively. Impress method was used to examine the adhesion between diamond film and the substrate. When deposition time is 1.5h, the adhesion between diamond film and the copper substrate is better than the others. When it was 2.5h or longer, because the graphite layers existed as intermediate, the adherence between the diamond films and copper substrates was very poor. Therefore, the diamond films were easily peeled off from the substrates. Otherwise, the second stage called annealing process after the deposition played an important role to the adhesion. The films would be easily peeled off by curling without the annealing process.


2008 ◽  
Vol 47 (4) ◽  
pp. 3050-3052
Author(s):  
Masataka Moriya ◽  
Yuji Matsumoto ◽  
Yoshinao Mizugaki ◽  
Tadayuki Kobayashi ◽  
Kouichi Usami

2000 ◽  
Vol 9 (7) ◽  
pp. 545-549
Author(s):  
Zhang Yong-ping ◽  
Gu You-song ◽  
Chang Xiang-rong ◽  
Tian Zhong-zhuo ◽  
Shi Dong-xia ◽  
...  

2021 ◽  
Vol 21 (8) ◽  
pp. 4412-4417
Author(s):  
Jonggeon Lee ◽  
Taemyung Kwak ◽  
Geunho Yoo ◽  
Seongwoo Kim ◽  
Okhyun Nam

In this study, we demonstrated the defect-selective etching and epitaxy technique for defect reduction of a heteroepitaxial chemical vapor deposition (CVD) diamond substrate. First, an 8 nm layer of nickel was deposited on the diamond surface using an e-beam evaporator. Then, defect-selective etching was conducted through an in situ single process using microwave plasma chemical vapor deposition (MPCVD). After defect-selective etching, the diamond layer was overgrown by MPCVD. The defect density measured from the atomic force microscope image decreased from 3.27×108 to 2.02×108 cm−2. The first-order Raman peak of diamond shifted from 1340 to 1336 cm−1, and the full width at half maximum (FWHM) decreased from 9.66 to 7.66 cm−1. Through the defect-selective etching and epitaxy technique, it was confirmed that the compressive stress was reduced and the crystal quality improved.


CrystEngComm ◽  
2022 ◽  
Author(s):  
Wei Cao ◽  
Zhibin Ma ◽  
Hongyang Zhao ◽  
Deng Gao ◽  
Qiuming Fu

On a semi-open holder, the homoepitaxial lateral growth of single-crystal diamond (SCD) was carried out via microwave plasma chemical vapor deposition (MPCVD). By tuning and optimizing two different structures of...


Sign in / Sign up

Export Citation Format

Share Document