Development of Nano-TiN Modified Cermet Cutter

2004 ◽  
Vol 471-472 ◽  
pp. 711-715
Author(s):  
Feng Xie ◽  
H.D. Yang ◽  
C.G. Zhang ◽  
N. Liu
Keyword(s):  
Mechanical Properties ◽  
New Technology ◽  
General Situation ◽  
Nano Technology ◽  
Modification Effect ◽  
Nano Material

Nano technology is a new technology and begun in 1980’s. The paper firstly overviews the development of cermet cutter and its general situation in research, and then introduces the inherent properties owned by nano-technology and nano-material. In the end the nano-TiN modified TiC-based cermet cutter is fabricated and the mechanical properties of the developed cutter are also tested and analyzed. In order to study nano-modification effect, both nano-modified cermet and general cermet have been made. The mechanical properties of two kinds of materials are also measured. By comparing the measured datum, it has been indicated that the nano-modified cermet has better mechanical properties and the nano-modification technology is effective. This presents a new way to increase the toughness of cermet cutter.

scholarly journals Oxazoline-based crosslinking reaction for coatings

2021 ◽  
Author(s):  
Philipp Knospe ◽  
Patrick Böhm ◽  
Jochen Gutmann ◽  
Michael Dornbusch
Keyword(s):  
Mechanical Properties ◽  
Loss Modulus ◽  
New Technology ◽  
Sol Gel ◽  
Polymer Network ◽  
Time Dependent ◽  
Crosslinking Reaction ◽  
Coating Materials ◽  
Rheological Measurements ◽  
Excellent Adhesion

AbstractNowadays, coating materials must meet high demands in terms of mechanical, chemical and optical properties in all areas of application. Amongst others, amines and isocyanates are used as crosslinking components for curing reactions, meeting the highly demanding properties of the coatings industry. In this work, a new crosslinking reaction for coatings based on oxazoline chemistry is investigated with the objective to overcome disadvantages of established systems and fulfill the need for sustainable coating compounds. The oxazoline-group containing resin, synthesized from commercially available substances, undergoes cationic self-crosslinking polymerization to build up a network based on urethane and amide moieties. NMR-, IR- and ES-mass spectroscopy are suitable techniques to characterize the synthesized oxazoline monomers, which are linked to polyisocyanates and polymerized afterwards via self-polymerization. The progress of crosslinking is followed by changes in IR spectra and by rheological measurements to calculate time dependent values for storage and loss modulus. The glass transition temperature of the resulting coating is determined, too. Furthermore, sol–gel-analysis is performed to determine the degree of crosslinking. After application on steel and aluminium panels, application tests are performed. In addition to excellent adhesion to the substrate, the polymer network shows promising mechanical properties and with that it could represent a new technology for the coatings industry.

scholarly journals The Effect of Plasma Pretreatment on the Morphology and Properties of Hitus Coatings

2020 ◽  
Vol 20 (1) ◽  
pp. 21-29
Author(s):  
Lenka Kvetková ◽  
Petra Hviščová ◽  
Dávid Medveď ◽  
František Lofaj
Keyword(s):  
Mechanical Properties ◽  
New Technology ◽  
Rf Plasma ◽  
Plasma Power ◽  
Rf Power ◽  
Properties Of Coatings ◽  
Plasma Pretreatment ◽  
Significant Change ◽  
Scratch Behavior

Abstract WC coatings prepared by High Target Utilization Sputtering (HITUS), a relatively new technology, were deposited on three types of substrates. These were silicon (111), steel (100Cr6), and ceramic (WC-Co). The influence of RF plasma power pretreatment on final properties of WC coatings was investigated with two interlayer materials for bonding. The morphology, roughness, and mechanical properties of coatings were studied. The relation between plasma RF power and roughness was found. No significant change in mechanical properties was detected with change in plasma RF power. The dependence of nanohardness and scratch behavior on HITUS WC coatings was investigated.

scholarly journals Role of Piezoelectric Elements in Finding the Mechanical Properties of Solid Industrial Materials

2018 ◽  
Vol 8 (10) ◽  
pp. 1737 ◽  
Author(s):  
Arshed Mohammed ◽  
Sallehuddin Haris ◽  
Mohd Nuawi
Keyword(s):  
Mechanical Properties ◽  
State Of The Art ◽  
New Technology ◽  
Material Testing ◽  
Current Status ◽  
Piezoelectric Elements ◽  
Need To Evaluate ◽  
Recent Developments ◽  
The Many

Recent developments in ultrasonic material testing have increased the need to evaluate the current status of the different applications of piezoelectric elements (PEs). This research have reviewed state-of-the-art emerging new technology and the role of PEs in tests for a number of mechanical properties, such as creep, fracture toughness, hardness, and impact toughness, among others. In this field, importance is given to the following variables, namely, (a) values of the natural frequency to PEs, (b) type and dimensions of specimens, and (c) purpose of the tests. All these variables are listed in three tables to illustrate the nature of their differences in these kinds of tests. Furthermore, recent achievements in this field are emphasized in addition to the many important studies that highlight the role of PEs.

scholarly journals Feasibility study of a novel hot stamping process for Ti6Al4V alloy

2018 ◽  
Vol 190 ◽  
pp. 08001
Author(s):  
Mateusz Kopec ◽  
Kehuan Wang ◽  
Yaoqi Wang ◽  
Liliang Wang ◽  
Jianguo Lin
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Phase Transformation ◽  
New Technology ◽  
Hot Stamping ◽  
Constant Strain Rate ◽  
Tensile Tests ◽  
Ti6al4v Titanium Alloy ◽  
Stamping Process ◽  
Forming Tools

To investigate the feasibility of a novel hot stamping process for the Ti6Al4V titanium alloy using low temperature forming tools, mechanical properties of the material were studied using hot tensile tests at a temperature range of 600 - 900°C with a constant strain rate of 1s-1. Hot stamping tests were carried out to verify the feasibility of this technology and identify the forming window for the material. Results show that when the deformation temperature was lower than 700°C, the amount of elongation was less than 20%, and it also had little change with the temperature. However, when the temperature was higher than 700°C, a good ductility of the material can be achieved. During the forming tests, parts failed at lower temperatures (600°C) due to the limited formability and also failed at higher temperatures (950°C) due to the phase transformation. The post-form hardness firstly decreased with the temperature increasing due to recovery and then increased due to the phase transformation. Qualified parts were formed successfully between temperatures of 750 - 850°C, which indicates that this new technology has a great potential in forming titanium alloys sheet components.

scholarly journals Hydrogels Containing the Ferri/Ferrocyanide Redox Couple and Ionic Liquids for Thermocells

2019 ◽  
Vol 72 (2) ◽  
pp. 112 ◽  
Author(s):  
Matthew Russo ◽  
Holly Warren ◽  
Geoffrey M. Spinks ◽  
Douglas R. MacFarlane ◽  
Jennifer M. Pringle
Keyword(s):  
Mechanical Properties ◽  
Ionic Liquids ◽  
Solid State ◽  
Waste Heat ◽  
New Technology ◽  
Redox Couple ◽  
Low Grade ◽  
Aqueous Electrolytes ◽  
Hydrogel Network ◽  
Water Based

Thermoelectrochemical cells are a promising new technology for harvesting low-grade waste heat. The operation of these cells relies on a redox couple within an electrolyte, which is most commonly water-based, and improvement of these materials is a key aspect of the advancement of this technology. Here, we report the gelation of aqueous electrolytes containing the K3Fe(CN)6/K4Fe(CN)6 redox couple using a range of different polymers, including polyvinyl alcohol (PVA), sodium carboxymethyl cellulose (Cmc), polyacrylamide (PAAm), and two commercial polyurethane-based polymers: HydroMed D640 and HydroSlip C. These polymers produce quasi-solid-state electrolytes with sufficient mechanical properties to prevent leakage, and allow improved device flexibility and safety. Furthermore, the incorporation of various ionic liquids within the optimized hydrogel network is investigated as a route to enhance the electrochemical and mechanical properties and thermal energy harvesting performance of the hydrogels.

Influence of Stirring Time and Holding Time on Microstructure and Properties of the A356 Alloy Modified by Sc

2013 ◽  
Vol 750-752 ◽  
pp. 687-690 ◽  
Author(s):  
Su Zhang ◽  
Gang Yang ◽  
Jian Hong Yi ◽  
Hong Yan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Grain Boundary ◽  
Eutectic Silicon ◽  
A356 Alloy ◽  
Holding Time ◽  
Test Results ◽  
Modification Effect ◽  
Microstructure And Mechanical Properties ◽  
Stirring Time

Effects of the holding time and the stirring time on the microstructure and mechanical properties of A356 alloy modified by Sc are researched. According to the test results, most of the eutectic silicon phases have changed to the shape of creeping point, dispersed in the grain boundary of α (Al) phase while stirring 1 minute, in which case both the tensile strength and elongation reach the highest, resulting in the best modification effect. The results also indicate that microstructure and mechanical properties of the alloy reach are the best modification effect when the melt is held 15 minute. It can be known that the optimal stirring time is 1 minute and the optimal holding time is 15 minute in the experiment condition of the work.

The Effect of the Deformation Method of the Billets on Mechanical Properties of Molybdenum Bars and Wire

2020 ◽  
Vol 864 ◽  
pp. 204-210
Author(s):  
Sergey Gorbatyuk ◽  
Dmitry Efremov ◽  
Sergei Albul ◽  
Natalya Kirillova
Keyword(s):  
Mechanical Properties ◽  
Comparative Analysis ◽  
High Temperatures ◽  
Rolling Mill ◽  
Mechanical Characteristics ◽  
New Technology ◽  
Deformation Resistance ◽  
Helical Rolling ◽  
Deformation Method ◽  
High Deformation

A procedure has been developed for calculating the geometric, kinematic and energy-power parameters of helical rolling, which allows a comparative analysis of the processes carried out in stands of various designs. Based on the results of this analysis, a helical rolling mill was designed and manufactured which allows to roll materials with high deformation resistance at high temperatures. The results of the study of the mechanical characteristics of molybdenum bars and wires made by new technology are presented.

Description of Degradation Process of Rubberized Lean Concrete

2014 ◽  
Vol 216 ◽  
pp. 67-72 ◽  
Author(s):  
Tomasz Sadowski ◽  
Daniel Pietras
Keyword(s):  
Mechanical Properties ◽  
New Technology ◽  
Young Modulus ◽  
Plain Concrete ◽  
Degradation Process ◽  
Damage Parameter ◽  
Stress Concentrations ◽  
Waste Tires ◽  
Concrete Production ◽  
Rubber Particles

Waste tires create big problem in the world as for their utilization. One domain in which this material is able to found promising application is civil engineering. The waste tires additive in the concrete manufacturing leads to change of mechanical properties such as: Young modulus, compressive strength, fracture toughness, energy absorption, brittleness, water absorption etc. It was partly reported in the literature only for the plain concrete. There is no investigations for a lean concrete - the material which has potential applications as a subgrade of roads. The aim of this paper is to investigate the importance of the rubber particles addition in the lean concrete production as for modification of the basic mechanical properties and further degradation of the material due to mechanical loading. The new technology of compaction of the concrete was elaborated to perform basic test: cyclic uniaxial compression and cyclic bending. In order to describe gradual degradation of the rubberized lean concrete a scalar damage parameter D related to loading history was proposed. The current value of the elastic modulus was expressed as E=Eo(1-D), where Eo denotes the initial value of the Young’s modulus. The paper includes also a numerical model of the beam made of the rubberized lean concrete, which is subjected to 3-point bending deformation. The stress distribution in this beam is highly non-homogeneous with visible stress concentrations around the rubber particles.

Study and Application of Nano Antibacterial Technology on Nonwoven Materials

2010 ◽  
Vol 148-149 ◽  
pp. 1112-1118 ◽  
Author(s):  
Xiao Ming Qian ◽  
Xu Pin Zhuang ◽  
Zhi Juan Zhang
Keyword(s):  
Nonwoven Fabric ◽  
Social Benefit ◽  
Nano Technology ◽  
Antibacterial Test ◽  
Application Field ◽  
Nonwoven Materials ◽  
Nano Material ◽  
The Future ◽  
Overall Performance ◽  
Product Application

The paper expatiates the nano material application on the nonwoven field and we carry on antibacterial test to the nonwoven fabric. All of these show that nano technology combine with nonwoven industry will have a great potential for widening product application field and promoting product overall performance, will create huge economical, social benefit on nonwoven industry in the future.

Sign in / Sign up

Export Citation Format

Share Document