Structure Characterization of Low Cost Fabricated Soft Material Built Microchannel

2016 ◽  
Vol 857 ◽  
pp. 578-582 ◽  
Author(s):  
Q. Humayun ◽  
Uda Hashim ◽  
Che Mohd Ruzaidi
Keyword(s):  
Biological Samples ◽  
Low Cost ◽  
Soft Material ◽  
Fabrication Process ◽  
Structure Characterization ◽  
Current Paper ◽  
Micro Channel ◽  
Inoculation Technique ◽  
Laboratory Activities

To perform the entire laboratory activities on a centimeter limit scale electronic chip, the most important aspect is to fabricate a device which persist sensitive and selective for the delivery of fluids flow and have the ability to execute a fast mixing of distinctive chemicals and bio samples. To resolve this issues the current paper is one of the good struggle, therefore the objective was arranged in according to the scope of research such as; to design and fabricate a polydimethylsiloxane (PDMS) material made, micro channel and its structure characterization for the investigation of internal subterranean area. By using an AutoCAD software the channel was first designed, however for the fabrication process the design was transferred to mask. Starting from SU-8 resist the pattern was transferred, and then by using the polydimethylsiloxane (PDMS) the mold was fabricated by adopting a low cost photolithography technique. Finally by employing Hawk 3 D surface nanoprofiler the structure was characterized. In our forthcoming research the device will be tested for real biological samples using a simple hand-operated inoculation technique.

A novel, nanocrystal (nc) based non-volatile memory device

2000 ◽  
Vol 638 ◽  
Author(s):  
Jan W. De Blauwe ◽  
Marty L. Green ◽  
Tom W. Sorsch ◽  
Garry R. Weber ◽  
Jeff D. Bude ◽  
...  
Keyword(s):  
Low Cost ◽  
Electrical Characterization ◽  
Memory Device ◽  
Fabrication Process ◽  
Floating Gate ◽  
Potential Candidate ◽  
Non Volatile Memory ◽  
Volatile Memory

AbstractThis paper describes the fabrication, and structural and electrical characterization of a new, aerosol-nanocrystal floating-gate FET, aimed at non-volatile memory (NVM) applications. This aerosol- nanocrystal NVM device features program/erase characteristics comparable to conventional stacked gate NVM devices, excellent endurance (>105 P/E cycles), and long-term non-volatility in spite of a thin bottom oxide (55-60Å). In addition, a very simple fabrication process makes this aerosol-nanocrystal NVM device a potential candidate for low cost NVM applications.

Development of nanomaterials-fabricated paper-based sensors for the analysis of environmental and biological samples: A Review

2021 ◽  
Vol 17 ◽  
Author(s):  
Monisha ◽  
Kamlesh Shrivas ◽  
Tarun Kumar Patle ◽  
Reena Jamunkar ◽  
Vikas Kumar Jain ◽  
...  
Keyword(s):  
Metal Ions ◽  
Biological Samples ◽  
Low Cost ◽  
Conductive Polymer ◽  
Toxic Metal ◽  
Clinical Samples ◽  
Toxic Substances ◽  
Environmental And Biological Samples ◽  
Printing Techniques

Background: Currently, the environmental and biological samples such as water, soil, vegetables, etc. are highly contaminated with metal ions, anions and pesticides. For analysis of these toxic substances from the environmental and biological samples, sophisticated and expensive instruments are being used. The present work deals with the developmentof a simple, faster, sensitive and economicalmethod forthe analysis of toxic substances present in the different samples. Methods: The general methods for synthesis and characterization of metallic (Ag, Au, Cu and graphene) nanoparticles and conductive polymer for its the development of conductive nano-ink, and fabrication of paper substrate by direct deposition and laser, wax, or inkjet printing techniques is reported. Results: Paper-based sensors fabricated with different nanomaterials used as colorimetric, electrochemical and fluorescence-based chemical sensors for the quantitative determinationof pesticides, toxic metal ions in various biological and clinical samples have been comprehensively discussed in this review. Conclusion: The low-cost, rapid, eco-friendly, flexible, portable, paper-based sensors using nanoparticles (NPs) is on-demand for on-site detection of differentchemical constituents present in various environmental, biological and clinical samples.

Inkjet-printed paper-based substrate-integrated waveguide (SIW) components and antennas

2013 ◽  
Vol 5 (3) ◽  
pp. 197-204 ◽  
Author(s):  
Riccardo Moro ◽  
Sangkil Kim ◽  
Maurizio Bozzi ◽  
Manos Tentzeris
Keyword(s):  
Low Cost ◽  
Fabrication Process ◽  
Substrate Integrated Waveguide ◽  
Passive Components ◽  
Novel Technology ◽  
Band Pass ◽  
Slotted Waveguide ◽  
Conformal Geometries ◽  
First Time

This paper presents a novel technology for the implementation of substrate-integrated waveguide (SIW) structures, based on a paper substrate and realized by an inkjet-printing fabrication process. The use of paper permits to implement low-cost microwave structures and components, by adopting a completely eco-friendly implementation technology. SIW structures appear particularly suitable for implementation on paper, due to the possibility to easily realize multilayered topologies and conformal geometries. In this paper, SIW passive components, and antennas (including straight interconnects, band-pass filters, and slotted-waveguide antennas) are proposed for the first time. The design of the components, the steps of the fabrication process, and the experimental characterization of the prototypes are reported in this paper.

scholarly journals A Simple and Robust Fabrication Process for SU-8 In-Plane MEMS Structures

Micromachines ◽  
2020 ◽  
Vol 11 (3) ◽  
pp. 317
Author(s):  
Chang Ge ◽  
Edmond Cretu
Keyword(s):  
Low Cost ◽  
Wet Etching ◽  
Fabrication Process ◽  
Mems Devices ◽  
Micro Electro Mechanical Systems ◽  
Direct Laser ◽  
Electrically Actuated ◽  
Open Window ◽  
New Processing

In this paper, a simple fabrication process for SU-8 in-plane micro electro-mechanical systems (MEMS) structures, called “border-bulk micromachining”, is introduced. It aims to enhance the potential of SU-8 MEMS structures for applications such as low-cost/disposable microsystems and wearable MEMS. The fabrication process is robust and uses only four processing steps to fabricate SU-8 in-plane MEMS structures, simplifying the fabrication flow in comparison with other reported attempts. The whole fabrication process has been implemented on copper-polyimide composites. A new processing method enables the direct, laser-based micromachining of polyimide in a practical way, bringing in extra processing safety and simplicity. After forming the polymeric in-plane MEMS structures through SU-8 lithography, a copper wet etching masked by the SU-8 structure layers is carried out. After the wet etching, fabricated in-plane MEMS structures are suspended within an open window on the substrate, similar to the final status of in-plane MEMS devices made from industrial silicon micromachining methods (such as SOIMUMPS). The last step of the fabrication flow is a magnetron sputtering of aluminum. The border-bulk micromachining process has been experimentally evaluated through the fabrication and the characterization of simple in-plane electrically actuated MEMS test structures. The characterization results of these simple test structures have verified the following process qualities: controllability, reproducibility, predictability and general robustness.

Characterization of microwave-sintered ceramic composites

1993 ◽  
Vol 51 ◽  
pp. 1136-1137
Author(s):  
X. Zhang ◽  
Y. Pan ◽  
T.T. Meek
Keyword(s):  
Matrix Material ◽  
Maximum Output Power ◽  
Ceramic Matrix Composite ◽  
Ceramic Composites ◽  
Processing Technique ◽  
Structure Characterization ◽  
Alumina Powder ◽  
Maximum Output ◽  
Sintered Ceramic

Industrial microwave heating technology has emerged as a new ceramic processing technique. The unique advantages of fast sintering, high density, and improved materials properties makes it superior in certain respects to other processing methods. This work presents the structure characterization of a microwave sintered ceramic matrix composite.Commercial α-alumina powder A-16 (Alcoa) is chosen as the matrix material, β-silicon carbide whiskers (Third Millennium Technologies, Inc.) are used as the reinforcing element. The green samples consisted of 90 vol% Al2O3 powder and 10 vol% ultrasonically-dispersed SiC whiskers. The powder mixture is blended together, and then uniaxially pressed into a cylindrical pellet under a pressure of 230 MPa, which yields a 52% green density. The sintering experiments are carried out using an industry microwave system (Gober, Model S6F) which generates microwave radiation at 2.45 GHz with a maximum output power of 6 kW. The composites are sintered at two different temperatures (1550°C and 1650°C) with various isothermal processing time intervals ranging from 10 to 20 min.

scholarly journals Microstructure and Thermoelectric Properties of (Bi0.48Sb1.52)Te3 Thick Films Prepared with Tape Casting Method

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 140
Author(s):  
Lichen Liu ◽  
Ziping Cao ◽  
Min Chen ◽  
Jun Jiang
Keyword(s):  
Thermoelectric Properties ◽  
Low Cost ◽  
Thick Films ◽  
Tape Casting ◽  
Casting Process ◽  
Casting Method ◽  
Glass Substrates ◽  
Conductive Films ◽  
Casting Technology

This paper reports the fabrication and characterization of (Bi0.48Sb1.52)Te3 thick films using a tape casting process on glass substrates. A slurry of thermoelectric (Bi0.48Sb1.52)Te3 was developed and cured thick films were annealed in a vacuum chamber at 500–600 °C. The microstructure of these films was analyzed, and the Seebeck coefficient and electric conductivity were tested. It was found that the subsequent annealing process must be carefully designed to achieve good thermoelectric properties of these samples. Conductive films were obtained after annealing and led to acceptable thermoelectric performance. While the properties of these initial materials are not at the level of bulk materials, this work demonstrates that the low-cost tape casting technology is promising for fabricating thermoelectric modules for energy conversion.

Sign in / Sign up

Export Citation Format

Share Document