Analysis of the Effects of Dynamic Alloying on the Structure of Aluminium and its Alloys

2021 ◽  
Vol 320 ◽  
pp. 8-13
Author(s):  
Yulia Usherenko ◽  
Viktor Mironov ◽  
Sergey Usherenko
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
High Speed ◽  
Matrix Material ◽  
Structure Change ◽  
Cosmic Dust ◽  
Structural Elements ◽  
High Speed Stream ◽  
Sic Particles ◽  
The Matrix

The dynamic alloying of aluminum and its alloy with a high-speed stream of silicon carbide (SiC) particles simulates the effect of a stream of cosmic dust on spacecraft materials. The study showed a structure change in the volume of aluminum and its alloy and the formation of new structural elements. The transformation of the structure during dynamic alloying leads to a change of the composition and mechanical properties of the matrix material.

scholarly journals Microstructural analysis of Al6063/sic with calcium additives for hardness enhancement

2018 ◽  
Vol 225 ◽  
pp. 03007
Author(s):  
Balaji Bakthavatchalam ◽  
Khairul Habib ◽  
Namdev Patil ◽  
Omar A Hussein
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Matrix Material ◽  
Microstructural Analysis ◽  
Wear Loss ◽  
Alloying Element ◽  
Silicon Phase ◽  
High Durability ◽  
The Matrix ◽  
Al6063 Alloy

Microstructural Analysis plays an important role in enhancing the mechanical properties of metals and composites. Usually Aluminium Silicon Carbide (Al6063/SiC) alloys are mixed with strontium, sodium and antimony for high durability even though they are toxic and costly. As an alternative calcium is used as an alloying element to improve the mechanical property of Al6063/Sic alloy. In this paper Al6063 is chosen as the matrix material while Sic is used as a reinforcement where calcium powder is added to modify the silicon phase of the composite. Finally, concentration of Silicon carbide is varied from 0 to 150 mg to produce four specimens of Al6063 alloy and it is subjected to microstructure analysis which showed the reduction of grain size and therefore improvement in the hardness from 52.9 HV to 58.4 HV and decrease in the wear loss from 3.97 to 3.27 percentage.

CO2 Laser Cladding of Mild Steel Using Iron Based Powder and Silicon Carbide Particles

2013 ◽  
Vol 748 ◽  
pp. 269-272 ◽  
Author(s):  
Mum Wai Yip ◽  
Stuart Barnes
Keyword(s):  
Silicon Carbide ◽  
Continuous Wave ◽  
Matrix Material ◽  
Feed System ◽  
Reinforce Metal Matrix Composite ◽  
Melt Pool ◽  
Sic Particles ◽  
The Matrix ◽  
Iron Based ◽  
Silicon Carbide Particles

The objective of this research was to develop a new form of clad layer by producing a Silicon Carbide (SiC) particle reinforce Metal Matrix Composite (MMC) using the iron based alloys as the matrix material. A 1.2kW continuous wave CO2 laser was used in this research. A gravity feed system was used with one powder feed which contained different percentages of SiC particles and iron based powder. Experimental results showed that the decomposition of SiC particles was observed and only a few SiC particles were found in the clad matrix. High micro hardness values were found in the SiC clad which were in excess of 1000 HV. However, most of the SiC were evaporated which created porosity in the melt pool. Therefore, blown powder technique is recommended for overcome this problem.

scholarly journals Microstructure Characteristics and Strengthening Behavior of Cu-Bearing Non-Oriented Silicon Steel: Conventional Process versus Strip Casting

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1815
Author(s):  
Feng Fang ◽  
Diwen Hou ◽  
Zhilei Wang ◽  
Shangfeng Che ◽  
Yuanxiang Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
High Speed ◽  
Silicon Steel ◽  
Strip Casting ◽  
Precipitation Strengthening ◽  
Conventional Process ◽  
Core Losses ◽  
The Matrix ◽  
Bcc Structure

Based on conventional hot rolling processes and strip casting processes, Cu precipitation strengthening is used to improve the strength of non-oriented silicon steel in order to meet the requirements of high-speed driving motors of electric vehicles. Microstructure evolution was studied, and the effects of Cu precipitates on magnetic and mechanical properties are discussed. Compared with conventional processes, non-oriented silicon steel prepared by strip casting exhibited advantages with regard to microstructure optimization with coarse grain and {100} texture. Two-stage rolling processes were more beneficial for uniform microstructure, coarse grains and improved texture. The high magnetic induction B50 of 1.762 T and low core losses with P1.5/50, P1.0/400 and P1.0/1000 of 1.93, 11.63 and 44.87 W/kg, respectively, were obtained in 0.20 mm sheets in strip casting. Cu precipitates significantly improved yield strength over ~120 MPa without deteriorating magnetic properties both in conventional process and strip casting. In the peak stage aged at 550 °C for 120 min, Cu precipitates retained bcc structure and were coherent with the matrix, and the yield strength of the 0.20 mm sheet was as high as 501 MPa in strip casting. The main mechanism of precipitation strengthening was attributed to coherency strengthening and modulus strengthening. The results indicated that balanced magnetic and mechanical properties can be achieved in thin-gauge non-oriented silicon steel with Cu addition in strip casting.

Physical and Mechanical Properties of Composites with Aluminum Alloy Matrix Designed for Metal Forming

2013 ◽  
Vol 212 ◽  
pp. 59-62 ◽  
Author(s):  
Jerzy Myalski ◽  
Jakub Wieczorek ◽  
Adam Płachta
Keyword(s):  
Mechanical Properties ◽  
Metal Forming ◽  
Matrix Material ◽  
Physical And Mechanical Properties ◽  
Mechanical Mixing ◽  
Alloy Matrix ◽  
Segregation Process ◽  
The Matrix ◽  
Glass Carbon ◽  
Properties Of Composites

The change of matrix and usage of the aluminum alloys designed for the metal forming in making the composite suspension allows to extend the processing possibility of this type of materials. The possibility of the metal forming of the composites obtained by mechanical mixing will extend the range of composite materials usage. Applying of the metal forming e.g. matrix forging, embossing, pressing or rolling, will allow to remove the incoherence of the structure created while casting and removing casting failures. In order to avoid the appearance of the casting failures the homogenization conditions need to be changed. Inserting the particles into the matrix influences on the shortening of the composite solidification. The type of the applied particles influenced the sedimentation process and reinforcement agglomeration in the structure of the composite. Opposite to the composites reinforced with one-phase particles applying the fasess mixture (glassy carbon and silicon carbide) triggered significant limitation in the segregation process while casting solidification. Inserting the particles into the AW-AlCu2SiMn matrix lowers the mechanical properties tension and impact value strength. The most beneficial mechanical properties were gained in case of heterofasess composites reinforced with the particle mixture of SiC and glass carbon. The chemical composition of the matrix material (AW-AlCu2SiMn) allows to increase additionally mechanical characteristics by the precipitation hardening reached through heat casting forming.

scholarly journals Translation of a Coated Rigid Spherical Inclusion in an Elastic Matrix: Exact Solution, and Implications for Mechanobiology

2019 ◽  
Vol 86 (5) ◽  
Author(s):  
Xin Chen ◽  
Moxiao Li ◽  
Shaobao Liu ◽  
Fusheng Liu ◽  
Guy M. Genin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Exact Solution ◽  
Analytical Solution ◽  
Spherical Inclusion ◽  
Matrix Material ◽  
Elastic Matrix ◽  
Protein Ligands ◽  
First Case ◽  
The Matrix ◽  
Matrix Modulus

The displacement of relatively rigid beads within a relatively compliant, elastic matrix can be used to measure the mechanical properties of the matrix. For example, in mechanobiological studies, magnetic or reflective beads can be displaced with a known external force to estimate the matrix modulus. Although such beads are generally rigid compared to the matrix, the material surrounding the beads typically differs from the matrix in one or two ways. The first case, as is common in mechanobiological experimentation, is the situation in which the bead must be coated with materials such as protein ligands that enable adhesion to the matrix. These layers typically differ in stiffness relative to the matrix material. The second case, common for uncoated beads, is the situation in which the beads disrupt the structure of the hydrogel or polymer, leading to a region of enhanced or reduced stiffness in the neighborhood of the bead. To address both cases, we developed the first analytical solution of the problem of translation of a coated, rigid spherical inclusion displaced within an isotropic elastic matrix by a remotely applied force. The solution is applicable to cases of arbitrary coating stiffness and size of the coating. We conclude by discussing applications of the solution to mechanobiology.

Microstructures and Mechanical Properties of 6061 Al Matrix Smart Composite Containing TiNi Shape Memory Fiber

1996 ◽  
Vol 459 ◽  
Author(s):  
J. H. Lee ◽  
K. Hamada ◽  
K. Miziuuchia ◽  
M. Taya ◽  
K. Inoue
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Elevated Temperatures ◽  
Volume Fraction ◽  
Matrix Material ◽  
Matrix Alloy ◽  
Flow Strength ◽  
The Matrix ◽  
Shape Memory Fiber ◽  
Al Matrix

ABSTRACT6061 Al-matrix composite with TiNi shape memory fiber as reinforcement has been fabricated by vacuum hot pressing to investigate the microstructure and mechanical properties. The yield stress of this composite increases with increasing amount of prestrain, and it also depends on the volume fraction of fiber and heat treatment. The smartness of the composite is given due to the shape memory effect of the TiNi fiber which generates compressive residual stresses in the matrix material when heated after being prestrained. Microstructual observations have revealed that interfacial reactions occur between the matrix and fiber, creating two intermetallic layers. The flow strength of the composite at elevated temperatures is significantly higher than that of the matrix alloy without TiNi fiber.

STUDY OF MECHANICAL PROPERTIES AND FRACTURE MODE OF ALUMINA-SILICON CARBIDE NANOCOMPOSITES

2012 ◽  
Vol 05 ◽  
pp. 551-558 ◽  
Author(s):  
A. RAHIMNEZHAD YAZDI ◽  
H.R. BAHARVANDI ◽  
H. ABDIZADEH ◽  
N. EHSANI
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Flexural Strength ◽  
Fracture Mode ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sic Particles ◽  
Scanning Electron

In this study Al 2 O 3- SiC nanocomposites have been fabricated by mixing of alumina and silicon carbide nano powders, followed by hot pressing at 1700°C. The mechanical properties and fracture mode of Al 2 O 3- SiC nanocomposites containing different volume fractions (5, 10 and 15%) of nano scale SiC particles were investigated and compared with those of alumina. Al 2 O 3- SiC powders were prepared by planetary milling in isopropanol. Fracture mode of specimens was investigated by means of scanning electron microscopy. Nanocomposites were tougher than alumina when they were hot pressed at the same temperature, and the values of nanocomposite's flexural strength and hardness were higher than those of alumina. Flexural strength, hardness and fracture toughness of the nanocomposites increase by increasing the volume percent of SiC up to 10% and then decrease slightly. The Scanning electron microscopy observations showed that fracture mode changes from intergranular for alumina to transgranular for nanocomposites. Finally X-ray diffraction analysis couldn't detect any chemical reactions between Al 2 O 3 and SiC particles.

scholarly journals Impact of the reinforced metal structure on the mechanical properties foamed aluminium composites at the load

2021 ◽  
Vol 8 (1) ◽  
pp. 318-326
Author(s):  
Olga Mareeva ◽  
Vladimir Ermilov ◽  
Vera Snezhko ◽  
Dmitrii Benin ◽  
Alexander Bakshtanin
Keyword(s):  
Mechanical Properties ◽  
Deformation Behavior ◽  
Matrix Material ◽  
Metal Structure ◽  
Absorption Capacity ◽  
Large Contribution ◽  
Strain Rates ◽  
Compression Tests ◽  
Stress Plateau ◽  
The Matrix

Abstract This paper is an experimental study of the quasi-static mechanical compressive properties of the reinforced closed-cell aluminum alloy foams with different cell orientations at different strain rates. The reinforced foam samples were obtained via the powder metallurgical route. The results of the compression tests revealed that the deformation behavior and mechanical properties of foamed aluminum composites are highly dependent on the orientation of the reinforcing mesh. Differences in the deformation behavior of foams appear to be influenced by the mechanical properties of the matrix material, by foam deformation mechanisms, and by the mechanical properties of the reinforcement. The yield stress, plateau stress, densification stress, and energy absorption capacity of unreinforced foam samples improved linearly with increasing strain rate due to dynamic recrystallization and softening of the foam matrix material. The reinforced foam samples exhibit nonlinear deformation behavior. It was also found that the mechanical properties reduction of transverse reinforced foams was slightly lower compared to foams with longitudinal reinforcement at varying strain rates because of the large contribution of the mechanical properties of the reinforcement. The results of the present study can be employed to modelling and obtain impact-resistant fillers for complex structures in transport construction.

scholarly journals Investigation on Physical and Mechanical Properties of Banana and Palmyra Fiber Reinforced Epoxy Composites

2020 ◽  
Vol 70 (2) ◽  
pp. 167-180
Author(s):  
Vennapusa Vijaya Bhaskar ◽  
Kolla Srinivas ◽  
Devireddy Siva Bhaskara Rao
Keyword(s):  
Mechanical Properties ◽  
Hybrid Composites ◽  
Matrix Material ◽  
Weight Ratio ◽  
Physical And Mechanical Properties ◽  
Epoxy Composites ◽  
Fiber Reinforced ◽  
Micro Structure ◽  
Interfacial Analysis ◽  
The Matrix

AbstractThe present work addresses the physical and mechanical properties of banana and palmyra fiber reinforced epoxy composites with the aim of study on the effect of weight ratio and fiber percentage. The banana and palmyra fibers were arranged with different weight ratios (1:1, 1:3, and 3:1) and then mixed with the epoxy matrix by hand lay-up technique to prepare the hybrid composites with various fiber percentages (10%, 20%, 30% and 40%). The properties are measured by testing its density, water absorption, tensile strength, impact strength, hardness and flexural strength and compared. From the results, it was indicated that addition of banana and palmyra fiber in to the matrix material up to 30% by fiber percentage results in increasing the mechanical properties and slightly variation with weight ratios. Interfacial analysis of the hybrid composites were also observed by using scanning electron microscope (SEM) to study the internal failures and micro structure of the tested specimen.

scholarly journals Improving Some Mechanical Properties and Thermal conductivity of PMMA Polymer by using Environmental Waste

2021 ◽  
pp. 2188-2196
Author(s):  
Tagreed M. Al-Saadi ◽  
Anaam W. Watan ◽  
Hanaa G. Attiya
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Environmental Problem ◽  
Matrix Material ◽  
Weight Fraction ◽  
Reinforcement Rate ◽  
Mechanical And Thermal Properties ◽  
The Matrix ◽  
Pmma Polymer ◽  
Composite Samples

This study was achieved to satisfy two goals, the first of which is to treat an environmental problem represented by the disposal of date seeds, and the second is the use of these wastes to improve some mechanical and thermal properties of poly methyl methacrylate PMMA through strengthening different proportions of the powder of date seeds. Particles of date seeds were used as a natural strengthening material for PMMA polymer, by mixing the matrix material (resin) with the hardener while still stirring continuously for a period of 10 min. After that, the samples of the reinforced material were prepared by adding the powder of date seeds, which is the reinforcing substance, with different percentages of weight fraction (0, 0.5, 1, 2, 3, 5 wt. %) and a grain size of <75 µm, while continuing to stir (10 min) for a second time. The composite samples were prepared by the Hand-Lay-up method and cut according to the standard ASTM. Thermal conductivity and some mechanical properties, such as impact strength, tensile strength, compressive strength, flexural strength, and hardness, were studied. An improvement was found in all properties at the reinforcement rate of 1-2 wt. %.

Sign in / Sign up

Export Citation Format

Share Document