scholarly journals Design and Analysis of Structural Folding Origami

2021 ◽  
pp. 46-48
Author(s):  
Pundru Srinivasa Rao
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Bending Stiffness ◽  
Surface Features ◽  
Texture Pattern ◽  
Local Texture ◽  
Flat Sheet ◽  
Thin Walled

The origami is transforming a flat sheet into some other shapes. It extends the mechanical properties of thin walled shells by introducing a local texture pattern, with surface features at a scale intermediate to the material and its structure. The primary application of local texture in thin-walled shells has been to increase the shell’s bending stiffness, their ability to absorb impact through plastic deformation of the texture pattern and in plane flexibility.

Severe plastic deformation of Al-1%Cu Alloy processed by a Simple Cyclic Extrusion Compression technique

2018 ◽  
Vol 1 (1) ◽  
pp. 77-90
Author(s):  
Walaa Abdelaziem ◽  
Atef Hamada ◽  
Mohsen A. Hassan
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Deformation Behavior ◽  
Cast Alloy ◽  
Surface Hardness ◽  
Grain Structure ◽  
Compression Technique ◽  
Cu Alloy ◽  
Cyclic Extrusion Compression

Severe plastic deformation is an effective method for improving the mechanical properties of metallic alloys through promoting the grain structure. In the present work, simple cyclic extrusion compression technique (SCEC) has been developed for producing a fine structure of cast Al-1 wt. % Cu alloy and consequently enhancing the mechanical properties of the studied alloy. It was found that the grain structure was significantly reduced from 1500 µm to 100 µm after two passes of cyclic extrusion. The ultimate tensile strength and elongation to failure of the as-cast alloy were 110 MPa and 12 %, respectively. However, the corresponding mechanical properties of the two pass CEC deformed alloy are 275 MPa and 35%, respectively. These findings ensure that a significant improvement in the grain structure has been achieved. Also, cyclic extrusion deformation increased the surface hardness of the alloy by 49 % after two passes. FE-simulation model was adopted to simulate the deformation behavior of the material during the cyclic extrusion process using DEFORMTM-3D Ver11.0. The FE-results revealed that SCEC technique was able to impose severe plastic strains with the number of passes. The model was able to predict the damage, punch load, back pressure, and deformation behavior.

Friction Force and Stresses Analysis for Contact of Assembled Details

2006 ◽  
Vol 113 ◽  
pp. 334-338
Author(s):  
Z. Dreija ◽  
O. Liniņš ◽  
Fr. Sudnieks ◽  
N. Mozga
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Plastic Deformation ◽  
Friction Force ◽  
Sliding Friction ◽  
Friction Model ◽  
Contact Interface ◽  
Finite Element Program ◽  
Elastic Plastic ◽  
Element Program

The present work deals with the computation of surface stresses and deformation in the presence of friction. The evaluation of the elastic-plastic contact is analyzed revealing three distinct stages that range from fully elastic through elastic-plastic to fully plastic contact interface. Several factors of sliding friction model are discussed: surface roughness, mechanical properties and contact load and areas that have strong effect on the friction force. The critical interference that marks the transition from elastic to elastic- plastic and plastic deformation is found out and its connection with plasticity index. A finite element program for determination contact analysis of the assembled details and due to details of deformation that arose a normal and tangencial stress is used.

scholarly journals Beam Theory of Thermal–Electro-Mechanical Coupling for Single-Wall Carbon Nanotubes

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 923
Author(s):  
Kun Huang ◽  
Ji Yao
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Beam Theory ◽  
Bending Stiffness ◽  
Single Wall Carbon Nanotubes ◽  
Beam Model ◽  
Euler Beam ◽  
New Model ◽  
Mechanical Coupling ◽  
Electrostatic Fields

The potential application field of single-walled carbon nanotubes (SWCNTs) is immense, due to their remarkable mechanical and electrical properties. However, their mechanical properties under combined physical fields have not attracted researchers’ attention. For the first time, the present paper proposes beam theory to model SWCNTs’ mechanical properties under combined temperature and electrostatic fields. Unlike the classical Bernoulli–Euler beam model, this new model has independent extensional stiffness and bending stiffness. Static bending, buckling, and nonlinear vibrations are investigated through the classical beam model and the new model. The results show that the classical beam model significantly underestimates the influence of temperature and electrostatic fields on the mechanical properties of SWCNTs because the model overestimates the bending stiffness. The results also suggest that it may be necessary to re-examine the accuracy of the classical beam model of SWCNTs.

scholarly journals Influence of Hydrostatic Extrusion on the Mechanical Properties of the Model Al-Mg Alloys

2021 ◽  
Author(s):  
Aleksandra Towarek ◽  
Wojciech Jurczak ◽  
Joanna Zdunek ◽  
Mariusz Kulczyk ◽  
Jarosław Mizera
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Hydrostatic Extrusion ◽  
Microstructure Formation ◽  
Initial State ◽  
Degree Of Deformation ◽  
Al Mg Alloys

AbstractTwo model aluminium-magnesium alloys, containing 3 and 7.5 wt.% of Mg, were subjected to plastic deformation by means of hydrostatic extrusion (HE). Two degrees of deformation were imposed by two subsequent reductions of the diameter. Microstructural analysis and tensile tests of the materials in the initial state and after deformation were performed. For both materials, HE extrusion resulted in the deformation of the microstructure—formation of the un-equilibrium grain boundaries and partition of the grains. What is more, HE resulted in a significant increase of tensile strength and decrease of the elongation, mostly after the first degree of deformation.

scholarly journals Microstructural Characterization and Mechanical Properties of Ti-6Al-4V Alloy Subjected to Dynamic Plastic Deformation Achieved by Multipass Hammer Forging with Different Forging Temperatures

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Xiurong Fang ◽  
Jiang Wu ◽  
Xue Ou ◽  
Fuqiang Yang
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Volume Fraction ◽  
Microstructural Characterization ◽  
Optical Microscope ◽  
Strain Rates ◽  
Materials Properties ◽  
Forging Process ◽  
Hammer Forging ◽  
Dynamic Plastic Deformation

Dynamic plastic deformation (DPD) achieved by multipass hammer forging is one of the most important metal forming operations to create the excellent materials properties. By using the integrated approaches of optical microscope and scanning electron microscope, the forging temperature effects on the multipass hammer forging process and the forged properties of Ti-6Al-4V alloy were evaluated and the forging samples were controlled with a total height reduction of 50% by multipass strikes from 925°C to 1025°C. The results indicate that the forging temperature has a significant effect on morphology and the volume fraction of primary α phase, and the microstructural homogeneity is enhanced after multipass hammer forging. The alloy slip possibility and strain rates could be improved by multipass strikes, but the marginal efficiency decreases with the increased forging temperature. Besides, a forging process with an initial forging temperature a bit above β transformation and finishing the forging a little below the β transformation is suggested to balance the forging deformation resistance and forged mechanical properties.

scholarly journals Tailoring a Low Young Modulus for a Beta Titanium Alloy by Combining Severe Plastic Deformation with Solution Treatment

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3467
Author(s):  
Anna Nocivin ◽  
Doina Raducanu ◽  
Bogdan Vasile ◽  
Corneliu Trisca-Rusu ◽  
Elisabeta Mirela Cojocaru ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Young Modulus ◽  
Orthopedic Implants ◽  
Beta Titanium Alloy

The present paper analyzed the microstructural characteristics and the mechanical properties of a Ti–Nb–Zr–Fe–O alloy of β-Ti type obtained by combining severe plastic deformation (SPD), for which the total reduction was of etot = 90%, with two variants of super-transus solution treatment (ST). The objective was to obtain a low Young’s modulus with sufficient high strength in purpose to use the alloy as a biomaterial for orthopedic implants. The microstructure analysis was conducted through X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) investigations. The analyzed mechanical properties reveal promising values for yield strength (YS) and ultimate tensile strength (UTS) of about 770 and 1100 MPa, respectively, with a low value of Young’s modulus of about 48–49 GPa. The conclusion is that satisfactory mechanical properties for this type of alloy can be obtained if considering a proper combination of SPD + ST parameters and a suitable content of β-stabilizing alloying elements, especially the Zr/Nb ratio.

scholarly journals Compressive Behaviour of Aluminium Pyramidal Lattice Material-Filled Tubes

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3817
Author(s):  
Yingjie Huang ◽  
Wenke Zha ◽  
Yingying Xue ◽  
Zimu Shi
Keyword(s):  
Mechanical Properties ◽  
Energy Absorption ◽  
Al Alloy ◽  
Compressive Behaviour ◽  
Lattice Material ◽  
Empty Tube ◽  
Thin Walled

This study focuses on the uniaxial compressive behaviour of thin-walled Al alloy tubes filled with pyramidal lattice material. The mechanical properties of an empty tube, Al pyramidal lattice material, and pyramidal lattice material-filled tube were investigated. The results show that the pyramidal lattice material-filled tubes are stronger and provide greater energy absorption on account of the interaction between the pyramidal lattice material and the surrounding tube.

Influence of Melt Temperature on Compressive Plasticity of a Cu-Zr-Al Bulk Metallic Glass

2010 ◽  
Vol 146-147 ◽  
pp. 517-521
Author(s):  
Sheng Hui Xie ◽  
Xie Rong Zeng ◽  
Dong Ju Fu ◽  
Lei Zhao ◽  
Qiang Hu
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Metallic Glasses ◽  
Mechanical Performance ◽  
Casting Temperature ◽  
Thermal And Mechanical Properties ◽  
Micro Hardness ◽  
Melt Temperature ◽  
Hardness Tests ◽  
Important Solution

Cu47.5Zr47.5Al5 bulk metallic glasses (BMGs) were cast from the melt temperature 1143 to 1373 K. The structure, thermal and mechanical properties of the BMGs were investigated by XRD, DSC, HRTEM, dilatometric measurements, micro-hardness tests and uniaxial compression. The results indicate that the microstructure and mechanical performance of BMGs are closely affected by the casting temperature. Proper casting temperature ensures the BMGs with large relaxed excess free volume (REFV) and nano-crystallites, which favor the plastic deformation in Cu47.5Zr47.5Al5 BMGs. Regulating the preparing parameters is an important solution to good plasticity in BMGs.

Deformation and Heat Treatment of Cold Drawn Gold

2007 ◽  
Vol 550 ◽  
pp. 289-294
Author(s):  
Suk Hoon Kang ◽  
Jae Hyung Cho ◽  
Joon Sub Hwang ◽  
Jong Soo Cho ◽  
Yong Jin Park ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Plastic Deformation ◽  
Mechanical Stability ◽  
Ion Beam ◽  
Quantitative Measure ◽  
Electron Backscattered Diffraction ◽  
Conducting Path ◽  
Deformation And Heat Treatment ◽  
Gold Wires

Cold drawn gold wires are widely applied in electronic packaging process to interconnect micro-electronic components. They basically provides a conducting path for electronic signal transfer, and experience thermo-mechanical loads in use. The mechanical stability of drawn gold wires is a matter of practical concern in the reliable functioning of electronic devices. It is known that mechanical properties of materials are deeply related to the microstructure. With appropriate control of deformation and heat processes, the mechanical properties of final products, such as tensile strength and elongation can be improved. Severe plastic deformation by torsion usually contributes to grain refinement and increment of strength. In this study, microstructure variations with torsion strain followed by drawing and heat treatment were investigated. Analyses by focused ion beam (FIB) and electron backscattered diffraction (EBSD) were carried out to characterize the effect of deformation and heat treatment on the drawn gold wires. Pattern quality of EBSD measurements was used as a quantitative measure for plastic deformation.

Sign in / Sign up

Export Citation Format

Share Document