scholarly journals Measurements of Aerosols and Charged Particles On the BEXUS18 Stratospheric Balloon

2019 ◽  
Author(s):  
Erika Brattich ◽  
Encarnación Serrano Castillo ◽  
Fabrizio Giulietti ◽  
Jean-Baptiste Renard ◽  
Sachi N. Tripathi ◽  
...  
Keyword(s):  
Fine Particles ◽  
Low Cost ◽  
Charged Particles ◽  
Negative Ions ◽  
Ground Level ◽  
Experimental Setup ◽  
Vertical Profiles ◽  
Aerosol Model ◽  
Analysis Experiment ◽  
Stratospheric Balloon

Abstract. This paper describes the aerosol measurements setup and results obtained during the BEXUS18 stratospheric balloon within the A5-Unibo (Advanced Atmospheric Aerosol Acquisition and Analysis) experiment performed on October 10th, 2014 in northern Sweden (Kiruna). The experimental setup was designed and developed by the University of Bologna with the aim of collecting and analyzing vertical profiles of atmospheric ions and particles together with atmospheric parameters (temperature, relative humidity and pressure) all along the stratospheric ascent of the BEXUS18 stratospheric balloon. Particles size distributions were measured with the MeteoModem Light Optical Aerosol Counter (LOAC) and air ion density was measured with a set of two commercial and portable ion counters. Though the experimental setup was based upon relatively low-cost and light-weight sensors, vertical profiles of all the parameters up to an altitude of about 27 km were successfully collected. The results obtained are useful for elucidating the relationships between aerosols and charged particles between ground level and the stratosphere with great potential in collecting and adding useful information in this field, also in the stratosphere where such measurements are rare. In particular, the equipment detected coherent vertical profiles for particles and ions, with a particularly strong correlation between negative ions and fine particles, possibly resulting from proposed associations between cosmic rays and ions as previously suggested. In addition, the detection of charged aerosols in the stratosphere is in agreement with the results obtained by a previous flight and with simulations conducted with a stratospheric ion-aerosol model. However, further measurements under stratospheric balloon flights equipped with a similar setup are needed to reach general conclusions on such important issues.

scholarly journals Measurements of aerosols and charged particles on the BEXUS18 stratospheric balloon

2019 ◽  
Vol 37 (3) ◽  
pp. 389-403 ◽  
Author(s):  
Erika Brattich ◽  
Encarnación Serrano Castillo ◽  
Fabrizio Giulietti ◽  
Jean-Baptiste Renard ◽  
Sachi N. Tripathi ◽  
...  
Keyword(s):  
Fine Particles ◽  
Low Cost ◽  
Charged Particles ◽  
Negative Ions ◽  
Ground Level ◽  
Experimental Setup ◽  
Vertical Profiles ◽  
Aerosol Model ◽  
Analysis Experiment ◽  
Stratospheric Balloon

Abstract. This paper describes the aerosol measurement setup and results obtained during the BEXUS18 (Balloon-borne Experiments for University Students) stratospheric balloon within the A5-Unibo (Advanced Atmospheric Aerosol Acquisition and Analysis) experiment performed on 10 October 2014 in northern Sweden (Kiruna). The experimental setup was designed and developed by the University of Bologna with the aim of collecting and analyzing vertical profiles of atmospheric ions and particles together with atmospheric parameters (temperature, relative humidity, and pressure) all along the stratospheric ascent of the BEXUS18 stratospheric balloon. Particle size distributions were measured with the MeteoModem Light Optical Aerosol Counter (LOAC) and air ion density was measured with a set of two commercial and portable ion counters. Though the experimental setup was based upon relatively low-cost and light-weight sensors, vertical profiles of all the parameters up to an altitude of about 27 km were successfully collected. The results obtained are useful for elucidating the relationships between aerosols and charged particles between ground level and the stratosphere, with great potential in collecting and adding useful information in this field, also in the stratosphere where such measurements are rare. In particular, the equipment detected coherent vertical profiles for particles and ions, with a particularly strong correlation between negative ions and fine particles, possibly resulting from proposed associations between cosmic rays and ions as previously suggested. In addition, the detection of charged aerosols in the stratosphere is in agreement with the results obtained by a previous flight and with simulations conducted with a stratospheric ion–aerosol model. However, further measurements under stratospheric balloon flights equipped with a similar setup are needed to reach general conclusions about such important issues.

Design of a Directional Olfactory Display to Study the Integration of Vision and Olfaction

2018 ◽  
Author(s):  
Lorenzo Micaroni ◽  
Marina Carulli ◽  
Francesco Ferrise ◽  
Monica Bordegoni ◽  
Alberto Gallace
Keyword(s):  
Virtual Reality ◽  
Low Cost ◽  
Olfactory Cues ◽  
Input Device ◽  
Experimental Setup ◽  
Initial Testing ◽  
Head Mounted Display ◽  
Innovative System ◽  
The One ◽  
Olfactory Display

This research aims to design and develop an innovative system, based on an olfactory display, to be used for investigating the directionality of the sense of olfaction. In particular, the design of an experimental setup to understand and determine to what extent the sense of olfaction is directional and whether there is prevalence of the sense of vision over the one of smell when determining the direction of an odor, is described. The experimental setup is based on low cost Virtual Reality (VR) technologies. In particular, the system is based on a custom directional olfactory display, an Oculus Rift Head Mounted Display (HMD) to deliver both visual and olfactory cues and an input device to register subjects’ answers. The VR environment is developed in Unity3D. The paper describes the design of the olfactory interface as well as its integration with the overall system. Finally the results of the initial testing are reported in the paper.

scholarly journals Microwave Assisted-Hydrothermal Synthesis of Nickel Ferrite Nanoparticles

2018 ◽  
Vol 34 (5) ◽  
pp. 2577-2582
Author(s):  
Mohamed H. H. Mahmoud ◽  
Mahmoud M. Hessien
Keyword(s):  
Nickel Ferrite ◽  
High Performance ◽  
Fine Particles ◽  
Low Cost ◽  
Nickel Chloride ◽  
Heating Time ◽  
Stoichiometric Ratio ◽  
Microwave Assisted ◽  
Xrd Patterns ◽  
Co Precipitation

Nanomagnetic ferrite materials are of great technological importance in several industries due to their high performance, ease of preparation and low cost. The ferrite properties are based on composition, structure and methods of preparation. Nickel ferrite, NiFe2O4, was prepared by the simple microwave assisted-hydrothermal method. Nickel chloride and ferric chloride solutions (stoichiometric ratio of 1: 2 respectively) were mixed, the pH was raised to 10.5 and the mixture was heated at 180 °C in a closed Teflon vessel using a microwave oven at different periods of time (2 - 24 h). The formed powders were examined by XRD, TEM, and VSM. The intensity of nickel-ferrite in the XRD patterns increased with time owing to increase in crystallinity of the formed phase. The TEM images showed that, the size was in the range of 20-40 nm and contents of fine particles noticeably decreased with increasing reaction time to 4-6 hrs and contents of more regular cubic particles are formed. The NiFe2O4 magnetization was continuesly increased with raising the heating time from 2h (9 emu/g) to 24 h (43 emu/g) which may be due to the high purity and crystallinity of the formed NiFe2O4. The results showed that the properties of the formed ferrite can be tailored by controlling the heating time. Microwave assisted co-precipitation followed by hydrothermal digestion resulted in a substance of good homogeneity and crystallinity at a short time.

scholarly journals Instrumentation for mechanical vibrations analysis in the time domain and frequency domain using the Arduino platform

2016 ◽  
Vol 38 (1) ◽  
Author(s):  
Marcus Varanis ◽  
Anderson Langone Silva ◽  
Pedro Henrique Ayres Brunetto ◽  
Rafael Ferreira Gregolin
Keyword(s):  
Signal Processing ◽  
Finite Elements ◽  
Time Domain ◽  
Good Accuracy ◽  
Low Cost ◽  
Analytical Models ◽  
Experimental Setup ◽  
Mechanical Vibrations ◽  
Python Language ◽  
The Time Domain

In this paper, we use the Arduino platform together with sensors as accelerometer, gyroscope and ultrasound, to measure vibrations in mechanical systems. The main objective is to assemble a signals acquisition system easy to handle, of low cost and good accuracy for teaching purposes. It is also used the Python language and its numerical libraries for signal processing. This paper proposes the study of vibrations of a beam, which is measured by position, velocity and acceleration. An experimental setup was implemented. The results obtained are compared with analytical models and computer simulations using finite elements. The results are in agreement with the literature.

scholarly journals Exploring Atmospheric Aerosols by Twilight Photometry

2008 ◽  
Vol 25 (9) ◽  
pp. 1600-1607 ◽  
Author(s):  
B. Padma Kumari ◽  
S. H. Kulkarni ◽  
D. B. Jadhav ◽  
A. L. Londhe ◽  
H. K. Trimbake
Keyword(s):  
Remote Sensing ◽  
Atmospheric Aerosols ◽  
Integrated Circuit ◽  
Tropical Meteorology ◽  
Indian Institute ◽  
Experimental Setup ◽  
Vertical Profiles ◽  
Remote Sensing Technique ◽  
Passive Remote Sensing ◽  
The Vertical Distribution

Abstract The instrument twilight photometer was designed, developed, and installed at the Indian Institute of Tropical Meteorology (IITM), Pune, India (18°43′N, 73°51′E), to monitor the vertical distribution of atmospheric aerosols. The instrument, based on passive remote sensing technique, is simple and inexpensive. It is operated only during twilights, and the method of retrieval of aerosol profile is based on a simple twilight technique. It functions at a single wavelength (660 nm), and a photomultiplier tube is used as a detector. The amplifier, an important component of the system, was designed and developed by connecting 10 single integrated-circuit (IC) amplifiers in parallel so that the noise at the output is drastically reduced and the sensitivity of the system has been increased. As a result, the vertical profiles are retrieved to a maximum of 120 km. A brief description of the basic principle of twilight technique, the experimental setup, and the method of retrieval of aerosol profiles using the above photometer are detailed in this paper.

A Mathematical Model to Examine Issues Associated With Using Portable Force-Measurement Technologies to Collect Infant Postural Data

2020 ◽  
Vol 8 (1) ◽  
pp. 14-37 ◽  
Author(s):  
James R. Chagdes ◽  
Joshua J. Liddy ◽  
Amanda J. Arnold ◽  
Laura J. Claxton ◽  
Jeffrey M. Haddad
Keyword(s):  
Mathematical Model ◽  
Center Of Pressure ◽  
Force Measurement ◽  
Low Cost ◽  
Body Sway ◽  
Support Surface ◽  
Experimental Setup ◽  
Mathematical Simulations ◽  
Additional Support

Portable force-measurement technologies are becoming increasingly popular tools to examine the maturation of postural motor milestones, such as sitting and standing, in infants. These convenient, low-cost devices provide numerous opportunities to characterize postural development outside of the laboratory. However, it is important to understand the unique challenges and technical limitations associated with collecting center of pressure (CoP) data using portable force-measurement technologies in infant populations. This study uses a mathematical model to examine issues that emerge when using portable force-measurement technologies to collect sitting and standing postural data in infants. The results of our mathematical simulations demonstrate that the CoP errors from portable force-measurement technologies depend on the posture examined (e.g., sitting vs. standing), the anthropometrics of the person (e.g., height and weight), the frequency of body sway, and the experimental setup (e.g., an additional support surface being placed on top of the device). Recommendations are provided for developmental researchers interested in adopting these technologies in infant populations.

THE IONIZATION OF THE ATMOSPHERE MEASURED FROM FLYING AIRCRAFT

1931 ◽  
Vol 5 (6) ◽  
pp. 625-635
Author(s):  
D. C. Rose
Keyword(s):  
Relative Humidity ◽  
Negative Ions ◽  
Ground Level ◽  
The State ◽  
Dust Particles ◽  
Measuring Apparatus ◽  
Positive Ions ◽  
Humidity Measurements ◽  
Water Drops ◽  
Atmospheric Ionization

The Gerdian type of atmospheric ionization measuring apparatus was attached to a cabin aeroplane so that the state of ionization of the atmosphere could be studied. The limitations of the apparatus for aeroplane use are discussed. Measurements were taken from ground level to heights of 15000 ft. The results are plotted in number of ions per cc. (separate curves for positive and negative) at different altitudes.The results indicate that at the cloud level there is an abnormal excess of small positive ions and a minimum in the excess of positive ions over negative ions from 4000–6000 ft. higher. This does not include large ions such as charged water drops or dust particles. The observations were taken in regions free from clouds, the cloud level being determined by observation on clouds in the sky, and by relative humidity measurements taken at the same time.

scholarly journals FINE PARTICLE REMOVAL USING HYDROPHOBIC MICROPOROUS POLYMERIC MEMBRANES

2019 ◽  
Vol 81 (3) ◽  
Author(s):  
Anita Kusuma Wardani ◽  
Ivan Ivan ◽  
Ivan Ruben Darmawan ◽  
Khoiruddin Khoiruddin ◽  
I Gede Wenten
Keyword(s):  
Removal Efficiency ◽  
Fine Particle ◽  
Fine Particles ◽  
Low Cost ◽  
Polymeric Membrane ◽  
Particle Removal ◽  
Air Filtration ◽  
Air Filter ◽  
Aerodynamic Properties ◽  
The World

The air quality in the world has been worsening in the last decades due to industrial, vehicle, cigarettes smoke, forest fire, and fuel usage. In this case, fine particles are the world’s greatest concern due to its aerodynamic properties which enable it to travel throughout the world. The current conventional technologies seem to have lost their reliability due to complexity, low removal efficiency, and high equipment cost. Membrane air filter brings new hope to answer this challenge. It gives high removal efficiency with an acceptable pressure drop to fulfill the need for clean air at a lower price. Recently, the introduction of nanofibre membrane as a low-cost membrane may broaden membrane application in air filtration. Compared to conventional membrane, nanofibre membrane offers some interesting features such as higher porosity, interconnected pore structure, and narrow pore size distribution that provide remarkable permeability. In this paper, the microporous polymeric membrane for air filtration especially for fine particles removal is reviewed including mechanism of fine particle removal, membrane preparation, and factor affecting filtration performance.

Sign in / Sign up

Export Citation Format

Share Document