Effect of Temperature on Tensile Properties of Vulcanized Rubber

1934 ◽  
Vol 7 (2) ◽  
pp. 371-386
Author(s):  
A. A. Somerville ◽  
W. F. Russell
Keyword(s):  
High Temperature ◽  
Tensile Properties ◽  
Room Temperature ◽  
Point Of View ◽  
Effect Of Temperature ◽  
Curing Conditions ◽  
Vulcanized Rubber ◽  
Before And After ◽  
Temperature Test ◽  
Better Than

Abstract The tensile properties and tear resistance of a large number of commercial inner tubes, before and after aging by different methods, are studied at 0°, 25°, and 100° C. A number of uncured bus-truck tube stocks are also studied from the point of view of their capacity to withstand high temperatures. The effect of testing rubber at 100° C. as compared with room temperature is discussed; how some compounds collapse at 100° C., while others have tensile properties equal to, or better than those at 25°, is shown. The effect of testing artificially aged specimens at 100° C., as well as at 25° C., is discussed; the high-temperature test may reveal conditions of deterioration and overcure that are not noticeable in the 25° tests. The compounding and curing conditions that lead to high tensile properties at 100° C., as well as those which cause inferior quality, are discussed.

scholarly journals Surface Recovery Investigation of Silicone Rubber Composites for Outdoor Electrical Insulation under Accelerated Temperature and Humidity

Polymers ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 3024
Author(s):  
M. Hassan Raza ◽  
Abraiz Khattak ◽  
Asghar Ali ◽  
Safi Ullah Butt ◽  
Bilal Iqbal ◽  
...  
Keyword(s):  
High Temperature ◽  
Silicone Rubber ◽  
Room Temperature ◽  
Nano Silica ◽  
Rubber Composites ◽  
Temperature And Humidity ◽  
Before And After ◽  
Overall Performance ◽  
Alumina Trihydrate ◽  
Better Than

Degradation of silicon rubber due to heat and humidity affect its performance in outdoor applications. To analyze the effects of high temperature and humidity on room temperature vulcanized (RTV) silicone rubber (SiR) and its composites, this study was performed. Five different sample compositions including neat silicone rubber (nSiR), microcomposites (15 wt% silica(SMC 15% SiO2) and 15 wt% ATH(SMC 15% ATH), nanocomposite (2.5 wt% silica(SNC 2.5% SiO2) and hybrid composite (10 wt% micro alumina trihydrate with 2 wt% nano silica(SMNC 10% ATH 2% SiO2) were prepared and subjected to 70 ˚C temperature and 80% relative humidity in an environmental chamber for 120 h. Contact angle, optical microscopy and Fourier transform infrared (FTIR) spectroscopy were employed to analyze the recovery properties before and after applying stresses. Different trends of degradation and recovery were observed for different concentrations of composites. Addition of fillers improved the overall performance of composites and SMC 15% ATH composite performed better than other composites. For high temperature and humidity, the ATH-based microcomposite was recommended over silica due to its superior thermal retardation properties of ATH. It has been proved that ATH filler is able to withstand high temperature and humidity.

Tensile Properties of Cast and Hot Isostatic Pressurized Ti-6Al-4Fe-xSi Alloys

2004 ◽  
Vol 449-452 ◽  
pp. 689-692
Author(s):  
E.H. Kim ◽  
Hi Won Jeong ◽  
Seung Eon Kim ◽  
Yong Taek Hyun ◽  
Yont Tai Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Tensile Properties ◽  
Room Temperature ◽  
Precipitation Hardening ◽  
Low Cost ◽  
High Strength ◽  
Alloy System ◽  
High Temperature Mechanical Properties ◽  
Better Than

A new high strength titanium alloy system with low cost alloying elements, such as Al, Fe, has been recently developed. In present study the expensive V was replaced with Fe, and Si was added from 0 to 7.5wt.%. The effect of Fe and Si on the microstructure and tensile properties of Ti-6Al-4Fe-xSi (x=0, 0.1, 0.25, 0.5, 0.75wt.%) alloys was investigated. The room and high temperature mechanical properties of Ti-6Al-4Fe alloys were better than those of the Ti-6Al-4V. It was mainly due to the phase boundary strengthening at ambient and high temperature. The strength and elongation of the developed alloys depended upon the Si contents. The Si elements made the grain boundary and colony size fine, and increased the strength of the developed alloys by solid solution and precipitation hardening. The tensile strength variation with the Si contents at room temperature and 400°C, and at 450°C and 500°C showed a similar behavior, respectively.

Sulfur Linkage in Vulcanized Rubber. Reaction of Methyl Iodide with Sulfur Compounds

1949 ◽  
Vol 22 (1) ◽  
pp. 1-7
Author(s):  
M. L. Selker
Keyword(s):  
Methyl Iodide ◽  
Room Temperature ◽  
Sulfur Compounds ◽  
Point Of View ◽  
Secondary Reaction ◽  
Reaction Products ◽  
Sulfide Sulfur ◽  
Vulcanized Rubber ◽  
Allyl Sulfide

Abstract The work described here is an extension of the study of the reaction of methyl iodide with sulfur compounds originally begun with the purpose of using such data in determining the sulfur linkage in vulcanized rubber. A previous paper dealt with the reactions of methyl iodide with propanethiol, propyl sulfide, propyl disulfide, allyl sulfide, and thiophene. This article adds to the list, n-butyl methallyl sulfide, allyl disulfide, allyl tetrasulfide, n-propyl tetrasulfide, and trithiane. The removal of combined sulfur from vulcanized rubber as trimethylsulfonium iodide on treatment with methyl iodide at room temperature was persuasive evidence of the presence of sulfide sulfur linked to allylic type residues. The evidence offered, however, did not constitute exclusive proof because it was not known whether still other types of sulfur linkage would also yield trimethylsulfonium iodide. To shed more light on this question, the sulfur linkages most likely to occur in vulcanizates—the allyl-alkyl monosulfide, diallyl and dialkyl di- and polysulfide—were investigated. The trithiane reaction is of interest mostly from the point of view of the reaction of overcured stocks or secondary reaction products stemming from the original polysulfides. The reactions were carried out using the method described in a previous paper.

Effect of CaO Addition on High Temperature Tensile Properties of Mg Casting Alloys

2009 ◽  
Vol 620-622 ◽  
pp. 291-294 ◽  
Author(s):  
Jung Ho Seo ◽  
Shae K. Kim
Keyword(s):  
Solid Solution ◽  
High Temperature ◽  
Tensile Properties ◽  
Alloy Element ◽  
Good Effect ◽  
Casting Alloys ◽  
Ca Addition ◽  
High Temperature Tensile ◽  
High Temperature Tensile Properties ◽  
Better Than

The microstructure, hardness and tensile properties of Mg-3Al, Mg-3Al-1.2Ca(AX31), Mg-3Al-1.2CaO(AO31), Mg-9Al, Mg-9Al-1.2Ca(AX91) and Mg-9Al-1.2CaO(AO91) alloys were investigated to identify the effect of CaO addition compared with Ca addition. The results show that the alloy element CaO has a good effect on high temperature tensile properties and CaO added alloys have superior high temperature performance compared with Ca added alloys. Addition of CaO results in the precipitation of Al2Ca phase (C15 phase) on the grain boundaries. This phase precipitated by the reduction of CaO leads to the refinement of a microstructure and improvement of tensile properties at elevated temperature similar to the Ca added Mg alloys. When added into molten Mg Ca makes solid solution in the Mg matrix up to 0.8wt %. But in case of CaO addition the thermally stable compound is precipitated directly without making solid solution with Mg matrix. Therefore, the high temperature tensile properties of CaO added Mg casting alloys are better than Ca added one at the same adding contents (1.2wt.%).

Effect of High Temperature Caliber Rolling on Microstructure and Room Temperature Tensile Properties of Mg-3Al-1Zn (AZ31) Alloy

2013 ◽  
Vol 209 ◽  
pp. 6-9 ◽  
Author(s):  
Rajendra Doiphode ◽  
S.V.S. Narayana Murty ◽  
Nityanand Prabhu ◽  
Bhagwati Prasad Kashyap
Keyword(s):  
Tensile Strength ◽  
High Temperature ◽  
Yield Strength ◽  
Strain Rate ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Az31 Alloy ◽  
Rolling Temperature ◽  
Grain Sizes

Mg-3Al-1Zn (AZ31) alloy was caliber rolled at 250, 300, 350, 400 and 450 °C. The effects of caliber rolling temperature on the microstructure and tensile properties were investigated. The room temperature tensile tests were carried out to failure at a strain rate of 1 x 10-4s-1. The nature of stress-strain curves obtained was found to vary with the temperature employed in caliber rolling. The yield strength and tensile strength followed a sinusoidal behaviour with increasing caliber rolling temperature but no such trend was noted in ductility. These variations in tensile properties were explained by the varying grain sizes obtained as a function of caliber rolling temperature.

scholarly journals Microstructure and Tensile Properties of Diffusion Bonded Austenitic Fe-Base Alloys—Before and After Exposure to High Temperature Supercritical-CO2

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 480 ◽  
Author(s):  
Sung Hwan Kim ◽  
Ji-Hwan Cha ◽  
Changheui Jang ◽  
Injin Sah
Keyword(s):  
High Temperature ◽  
Tensile Properties ◽  
Heat Exchangers ◽  
Boundary Migration ◽  
Bond Line ◽  
Grain Boundary Migration ◽  
Compact Type ◽  
Before And After ◽  
Temperature Exposure ◽  
Co2 Environment

Austenitic Fe-base alloys, SS 316H and Alloy 800HT, were diffusion bonded for use in compact-type heat exchangers in supercritical-carbon dioxide (S-CO2) Brayton cycles. For diffusion bonded 316H, grain boundary migration across the bond-line was observed despite the formation of some Cr-rich carbide, and its tensile properties were similar to those of as-received 316H. However, diffusion bonded Alloy 800HT exhibited severely degraded elongation compared to as-received 800HT due to the formation of continuous Ti-rich carbides along the bond-line. Post-bond heat treatment (PBHT) was found to improve elongation at fracture for diffusion bonded alloys. However, a subsequent corrosion test in S-CO2 at 600 °C (20 MPa) for 1000 h resulted in a loss of elongation. This was much more severe for PBHT-ed 800HT due to the formation of Cr-rich carbides at the bond-line. Meanwhile, it was found that the effect of ageing on loss of elongation during high temperature exposure was greater than that of S-CO2 environment.

Deformation of an extruded nickel beryllide between room temperature and 820 °C

1991 ◽  
Vol 6 (12) ◽  
pp. 2653-2659 ◽  
Author(s):  
G.M. Pharr ◽  
S.V. Courington ◽  
J. Wadsworth ◽  
T.G. Nieh
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Elevated Temperature ◽  
Flow Stress ◽  
Strain Hardening ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Compression Tests ◽  
Tension And Compression ◽  
Better Than

The mechanical properties of nickel beryllide, NiBe, have been investigated in the temperature range 20–820 °C. The room temperature properties were studied using tension, bending, and compression tests, while the elevated temperature properties were characterized in compression only. NiBe exhibits some ductility at room temperature; the strains to failure in tension and compression are 1.3% and 13%, respectively. Fracture is controlled primarily by the cohesive strength of grain boundaries. At high temperatures, NiBe is readily deformable—strains in excess of 30% can be achieved at temperatures as low as 400 °C. Strain hardening rates are high, and the flow stress decreases monotonically with temperature. The high temperature strength of NiBe is as good or better than that of NiAl, but not quite as good as CoAl.

Effect of Temperature on Crater Formation and Ejecta Composition in Aluminum Alloy Targets

2012 ◽  
Vol 706-709 ◽  
pp. 768-773
Author(s):  
Masahiro Nishida ◽  
Koichi Hayashi ◽  
Junichi Nakagawa ◽  
Yoshitaka Ito
Keyword(s):  
Aluminum Alloy ◽  
High Temperature ◽  
Low Temperature ◽  
Room Temperature ◽  
Effect Of Temperature ◽  
Crater Formation ◽  
Influence Of Temperature ◽  
Gas Gun ◽  
Influence Of Temperature On ◽  
Increasing Temperature

The influence of temperature on crater formation and ejecta composition in thick aluminum alloy targets were investigated for impact velocities ranging from approximately 1.5 to 3.5 km/s using a two-stage light-gas gun. The diameter and depth of the crater increased with increasing temperature. The ejecta size at low temperature was slightly smaller than that at high temperature and room temperature. Temperature did not affect the size ratio of ejecta. The scatter diameter of the ejecta at high temperature was slightly smaller than those at low and room temperatures.

Increased High Temperature Oxidation Resistance of Ni20Cr20Fe5Nb1Y2O3 Alloy with Nano-Sized Grains

2005 ◽  
Vol 486-487 ◽  
pp. 109-112 ◽  
Author(s):  
Il Ho Kim ◽  
S.I. Kwun
Keyword(s):  
Tensile Strength ◽  
High Temperature ◽  
Mechanical Alloying ◽  
Tensile Properties ◽  
Oxidation Resistance ◽  
Tensile Property ◽  
High Temperature Oxidation ◽  
Room Temperature ◽  
Dispersion Strengthening ◽  
Temperature Oxidation

The oxidation and tensile properties of a Ni20Cr20Fe5Nb alloy and a Ni20Cr20Fe 5Nb1Y2O3 alloy with nano-sized grains were compared with those of the comercial IN718 alloy. The oxidation resistance of the Ni20Cr20Fe5Nb1Y2O3 alloy was superior to that of the Ni20Cr20Fe5Nb and IN 718 alloys. This superior oxidation resistance was the result of both the formation of dense oxides on the surface of the alloy and the interruption of Cr migration in the alloy by the addition of Y2O3. Moreover, the tensile property of the Ni20Cr20Fe5Nb1Y2O3 alloy at room temperature and 400oC was higher than that of the Ni20Cr20Fe5Nb and IN718 alloys by more than 300MPa (30%). This result can be attributed to the dispersion strengthening of Y2O3. The relatively low tensile strength at 600°C and 800°C of the alloys fabricated by mechanical alloying was attributed to grain refinement showing intergranular fracture at high temperatures.

Design and Development of a 14-Pole High-Temperature Superconducting Filter at 127.5MHz

2013 ◽  
Vol 392 ◽  
pp. 672-675 ◽  
Author(s):  
Jian Chang Du ◽  
Lai Yun Ji ◽  
Li Juan He
Keyword(s):  
Thin Films ◽  
High Temperature ◽  
Return Loss ◽  
Band Pass Filter ◽  
Pass Filter ◽  
High Temperature Superconducting ◽  
Hts Filter ◽  
Band Pass ◽  
Temperature Test ◽  
Better Than

A high-temperature superconducting (HTS) band-pass filter centered frequency at 127.5MHz was successfully designed and developed. The HTS filter is 14-pole, adopting compact symmetrical dual-spiral resonators. The filter was fabricated on a 3-inch-diameter 0.5-mm-thick LaAlO3 wafer with double-sided DyBa2Cu3O7 thin films. Through the low temperature test, the insertion loss of the HTS filter is under 0.1dB, the bandwidth is 20 MHz, the return loss is better than-22dB and the out-of-band rejection is greater than 80dB. The filters measurements agree well with the simulation.

Sign in / Sign up

Export Citation Format

Share Document