Adsorption of Methylene Blue by Hydroxyl-Aluminum Pillared Montmorillonite

2020 ◽  
Vol 42 (4) ◽  
pp. 550-550
Author(s):  
Houria Rezala Houria Rezala ◽  
Houda Douba Houda Douba ◽  
Horiya Boukhatem and Amaya Romero Horiya Boukhatem and Amaya Romero
Keyword(s):  
Methylene Blue ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
Basal Spacing ◽  
Solution Ph ◽  
X Ray ◽  
Pillared Montmorillonite ◽  
Pseudo Second Order ◽  
Adsorption Desorption ◽  
Kinetics And Isotherms

A purified raw montmorillonite and hydroxy-aluminum pillared montmorillonite have been prepared from a natural bentonite from Maghnia, Algeria. These materials have been analyzed by X-ray fluorescence spectroscopy, X-ray diffraction, Infrared spectroscopy and nitrogen adsorption-desorption measurement. The pillared montmorillonite provided a certain increase of interlayer basal spacing and BET surface area and consequently the improvement of its capacities adsorption and decolorization of Methylene Blue. The adsorption properties of these materials were studied as a function of contact time, solution pH, initial Methylene Blue concentration and temperature. The adsorption kinetics and isotherms were well fitted by pseudo-second order and Freundlich models, respectively. In addition to that, thermodynamic studies showed an exothermic and a spontaneous process.

scholarly journals Adsorptive Removal of Methylene Blue and Crystal Violet onto Micro-Mesoporous Zr3O/Activated Carbon Composite: A Joint Experimental and Statistical Modeling Considerations

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
H. Ait Ahsaine ◽  
Z. Anfar ◽  
M. Zbair ◽  
M. Ezahri ◽  
N. El Alem
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Crystal Violet ◽  
Zirconium Oxide ◽  
Carbon Composite ◽  
Bet Surface Area ◽  
Sem Images ◽  
X Ray ◽  
Pseudo Second Order

Zirconium oxide/activated carbon (Zr3O/AC) composite was synthesized to remove methylene blue (MB) and crystal violet (CV) from the aqueous medium. The Zr3O/AC sample was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analyses (EDS), Raman spectroscopy (RS), BET surface area, and Fourier transform infrared spectroscopy (FTIR). XRD profiles confirmed the successful synthesis of the zirconium oxide/activated carbon composite. SEM images showed multideveloped walls with irregular particle size with channel arrays. The nitrogen physisorption combines I and IV types with a calculated BET surface area of 1095 m2/g. Raman spectrum illustrated a disorder of both crystalline structure and the graphitic structure. The adsorption was better fitted to the pseudo-second-order (PSO) kinetic model. Langmuir model fitted better the experimental results of MB adsorption, whereas the CV was better consistent with the Freundlich model. The obtained results suggested that the MB and CV adsorption might be influenced by the mass transfer that involves multiple diffusion steps. The maximum adsorption capacities are 208.33 and 204.12 mg/g for MB and CV, respectively. The MB and CV removal mechanisms were proposed, and statistical optimization was performed using central composite design combined with the response surface methodology.

Preparing Mesoporous Silica Doped with Iron via a Novel Method

2007 ◽  
Vol 121-123 ◽  
pp. 1313-1316
Author(s):  
H.D. Liu ◽  
Yun Fa Chen
Keyword(s):  
Mesoporous Silica ◽  
Nitrogen Adsorption ◽  
Silica Particles ◽  
Bet Surface Area ◽  
Iron Doping ◽  
Doping Amount ◽  
X Ray ◽  
Novel Method ◽  
Distribution State ◽  
Adsorption Desorption

Mesoporous silica particles doped with iron was prepared with a novel method. Nitrogen adsorption-desorption test indicated that the BET surface area decreased with the increasing of iron doping amount. Small-angle X-ray diffractometry (SAXD) analysis showed that more iron dopant gave rise to less orderly structured product. FITRanalysis were all carried out to study the iron valent and distribution state in the as-made mesoporous silica particles.

scholarly journals Adsorption of methylene blue onto activated carbon prepared from Lupinus Albus

2016 ◽  
Vol 22 (2) ◽  
pp. 155-165 ◽  
Author(s):  
Safiye Bağcı ◽  
Ayhan Ceyhan
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Ph Value ◽  
Chemical Activation ◽  
Lupinus Albus ◽  
Total Pore Volume ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
Maximum Adsorption Capacity ◽  
Solution Ph

The adsorption of methylene blue (MB) from synthetic aqueous solutions in batch experiments using Lupinus Albus-activated carbon (LAAC) by chemical activation with zinc chloride was investigated. Prior to adsorption experiments, surface/physical properties of LAAC were determined using Scanning Electron Microscopy, Fourier transform infrared Spectroscopy and nitrogen adsorption isotherm. In the adsorption experiments, effects of adsorption time, solution pH, MB concentration and amount of LAAC were investigated. The isotherm and kinetic parameters were used to describe the experimental data. The BET surface area was 1254 m2/g while its total pore volume was found to be 0.484 cm3/g. Maximum adsorption capacity occurred at solution pH value 10 and was recorded as 109.89 mg/g. Adsorption data were modeled using Langmuir, Freundlich and Temkin adsorption isotherms. Langmuir isotherm and pseudo-second-order models fit to the process and reaction kinetics correspondingly.

scholarly journals The Role of the Aluminum Source on the Physicochemical Properties of γ-AlOOH Nanoparticles

2020 ◽  
Vol 39 (1) ◽  
pp. 89
Author(s):  
Rafael Romero Toledo ◽  
Luis M. Anaya Esparza ◽  
J. Merced Martínez Rosales
Keyword(s):  
Electron Microscopy ◽  
Physicochemical Properties ◽  
Surface Area ◽  
Low Cost ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
Precipitation Method ◽  
X Ray ◽  
Aluminum Salts ◽  
Adsorption Desorption

The effect on the physicochemical properties of aluminum salts on the synthesis of γ-AlOOH nanostructures has been investigated in detail using a hydrolysis-precipitation method. X-ray fluorescence (XRF), Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), field-emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM), were used to characterize the synthesized samples. The specific surface area, pore size distribution and pore diameter of the different γ-AlOOH structures were discussed by the N2 adsorption-desorption analysis. According to the results of the nanostructure, characterization revealed that for synthesized γ-AlOOH nanostructures from AlCl3 and Al(NO3)3, obvious XRD peaks corresponding to the bayerite phase are found indicating an impure γ-AlOOH phase. Furthermore, the nitrogen adsorption-desorption analysis indicated that the obtained γ-AlOOH nanoparticles from Al2(SO4)3 of technical grade (95.0 % of purity) and low cost, possess a high BET surface area of approximately 350 m2/g, compared to the obtained nanostructures from aluminum sources reactive grade, which was attributed to the presence of Mg (0.9 wt.%) in its nanostructure.

scholarly journals Removal of Methylene Blue Dye from Wastewater Using Periodiated Modified Nanocellulose

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Hizkeal Tsade Kara ◽  
Sisay Tadesse Anshebo ◽  
Fedlu Kedir Sabir ◽  
Getachew Adam Workineh
Keyword(s):  
Methylene Blue ◽  
Adsorption Process ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Color Removal ◽  
Isotherm Models ◽  
Blue Dye ◽  
Solution Ph ◽  
X Ray ◽  
Pseudo Second Order

The study was focused on the preparation and characterizations of sodium periodate-modified nanocellulose (NaIO4-NC) prepared from Eichhornia crassipes for the removal of cationic methylene blue (MB) dye from wastewater (WW). A chemical method was used for the preparation of NaIO4-NC. The prepared NaIO4-NC adsorbent was characterized by using X-ray diffraction (XRD), Fourier transform infrared (FTIR), scanning electron microscope (SEM), energy-dispersive X-ray (EDX), and Brunauer–Emmett–Teller (BET) instruments. Next, it was tested to the adsorption of MB dye from WW using batch experiments. The adsorption process was performed using Langmuir and Freundlich isotherm models with maximum adsorption efficiency (qmax) of 90.91 mg·g−1 and percent color removal of 78.1% at optimum 30 mg·L−1, 60 min., 1 g, and 8 values of initial concentration, contact time, adsorbent dose, and solution pH, respectively. Pseudo-second-order (PSO) kinetic model was well fitted for the adsorption of MB dye through the chemisorption process. The adsorption process was spontaneous and feasible from the thermodynamic study because the Gibbs free energy value was negative. After adsorption, the decreased values for physicochemical parameters of WW were observed in addition to the color removal. From the regeneration study, it is possible to conclude that NaIO4-NC adsorbent was recyclable and reused as MB dye adsorption for 13 successive cycles without significant efficient loss.

TiO2 Hollow Spheres Obtained under Autogenic Pressure at Elevated Temperature

2009 ◽  
Vol 79-82 ◽  
pp. 525-528 ◽  
Author(s):  
Ke Xun Li ◽  
Hong Liang Li ◽  
Jun Hua Zhao ◽  
Ying Chun Zhu ◽  
Xiu Song Zhao
Keyword(s):  
Elevated Temperature ◽  
Diffuse Reflectance ◽  
Hollow Spheres ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surfactant Additive ◽  
Tio2 Hollow Spheres ◽  
Adsorption Desorption

Carbon/TiO2 composites were prepared via the reaction under Autogenic Pressure at Elevated Temperature (RAPET) using alkoxides as precursor, and then porous TiO2 hollow spheres were derived after removing the carbon ingredient by calcination at 600°C. The influence of surfactant additives, including the addition ratio and the nature of the surfactants, on the morphology and the structures of the Carbon/TiO2 composites and the derived TiO2 were also studied with scanning electron microscopy (SEM), X-ray diffraction (XRD), UV-Vis diffuse reflectance spectrophotoscopy (DRS) and nitrogen adsorption-desorption measurements. The results revealed that the morphology of the products turned to spherical and then fusiform and the structures turned from hollow to solid with the increasing of surfactant additive. The BET surface area of the hollow TiO2 was modified from 12m2/g to 57m2/g after calcinations. The XRD investigation indicates that the phases of the TiO2 in both the carbon/TiO2 composites and the derived TiO2 hollow spheres are anatase.

scholarly journals Adsorption of Arsenate from Aqueous Solution onto Modified Vietnamese Bentonite

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Nguyen Le My Linh ◽  
Duc Hoang Van ◽  
Tran Duong ◽  
Mai Xuan Tinh ◽  
Dinh Quang Khieu
Keyword(s):  
Aqueous Solution ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
X Ray ◽  
Surface Areas ◽  
Layered Clays ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Adsorption Desorption

In this study, pillared layered clays were prepared by modifying Vietnamese bentonite with polymeric Al and Fe. The obtained materials were characteristic of X-ray diffraction analysis, thermal analysis, and nitrogen adsorption/desorption isotherms. The results indicated that hydroxy-aluminum ([Al13O4(OH)24(H2O)12]7+) and poly-hydroxyl-Fe or polyoxo-Fe cations were intercalated into layers of clay, resulting in an increase of d001 values and of the specific surface areas compared with those of initial bentonite. Modified bentonites were employed to adsorb As(V) from aqueous solution. The adsorption of As(V) was strongly dependent on solution pH, and the maximum adsorption of modified bentonites was obtained in the pH 3.0 for Fe-bentonite and the pH 4.0 for Al-bentonite. The equilibrium adsorption study showed that the data were well fit by the Langmuir isotherm model. The maximum monolayer adsorption capacity of As(V) at 30°C derived from the Langmuir equation was 35.71 mg/g for Al-bentonite and 18.98 mg/g for Fe-bentonite. Adsorption kinetics, thermodynamics, and reusability of modified bentonites have been addressed.

scholarly journals Study of Methylene Blue Adsorption by Modified Kaolinite by Dimethyl Sulfoxide

2020 ◽  
Vol 27 (2) ◽  
pp. 225-239
Author(s):  
Salima Lellou ◽  
Samir Kadi ◽  
Laid Guemou ◽  
Jacques Schott ◽  
Hadj Benhebal
Keyword(s):  
Methylene Blue ◽  
Dimethyl Sulfoxide ◽  
Kinetic Data ◽  
Contact Time ◽  
Basal Spacing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pseudo Second Order ◽  
Scanning Electron ◽  
Good Agreement

AbstractTamazert kaolin was modified with dimethyl sulfoxide (DMSO). The starting material and resulting from the intercalation were characterized by X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy (SEM). Intercalation caused considerable changes in our clay by increasing the basal spacing to 11.22 Å, an intercalation rate of 98 %. The adsorption of methylene blue was studied as a function of pH, contact time, temperature, dye concentrations and adsorbents. Kinetic data have been adequately described by the pseudo-second order and intraparticle scattering model. The adsorption isotherm is in good agreement with the Redlich-Peterson model. A change in thermodynamic values (ΔH°, ΔS° and ΔG°) was observed after intercalation. Adsorption became non-spontaneous exothermic and ordered.

scholarly journals Adsorption performance of polydopamine-modified attapulgite granular adsorbent for methylene blue

2017 ◽  
Vol 77 (1) ◽  
pp. 167-176 ◽  
Author(s):  
Weisheng Zheng ◽  
Hailing Wang ◽  
Zhaolian Zhu ◽  
Peng Wei
Keyword(s):  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Adsorption Process ◽  
Dip Coating ◽  
N2 Adsorption ◽  
X Ray ◽  
Endothermic Process ◽  
Pseudo Second Order ◽  
Modified Attapulgite ◽  
Adsorption Desorption

Abstract Polydopamine-modified granule organo-attapulgite adsorbent (PDA-GOAT) was facilely prepared via a dip-coating approach. The samples were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. Surface area and pore size were calculated from the Brunauer–Emmett–Teller method by N2 adsorption–desorption isotherm. The adsorption behaviour of methylene blue (MB) onto PDA-GOAT was systematically investigated. The experimental data revealed that the adsorption process fitted well with the pseudo-second-order kinetics equation and the adsorption isotherm fitted better with the Langmuir model. Thermodynamic analyses illustrated that MB adsorption onto PDA-GOAT was a physisorption endothermic process. Importantly, PDA-GOAT can be regenerated by NaBH4 aqueous solution. The obtained results prove that PDA-GOAT can be a superior reusable adsorbent for the removal of MB from effluent.

scholarly journals Preparation of Cerium Modified Titanium Dioxide Nanoparticles and Investigation of Their Visible Light Photocatalytic Performance

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Jinfeng Liu ◽  
Haiyan Li ◽  
Qiuye Li ◽  
Xiaodong Wang ◽  
Min Zhang ◽  
...  
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Titanium Dioxide Nanoparticles ◽  
Spectral Response ◽  
Anatase Phase ◽  
Nitrogen Adsorption ◽  
Mesoporous Structure ◽  
Bet Surface Area ◽  
X Ray ◽  
Adsorption Desorption

Mesoporous CeOx/TiO2nanoparticles have been successfully synthesized using titanate nanotubes as precursor through the hydrothermal-calcination method. The as-prepared materials were characterized by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscope (TEM), UV-vis diffuse reflectance spectra and nitrogen adsorption-desorption isotherm analysis. All the obtained CeOx/TiO2materials exhibit anatase phase. Ce element existed in two valance states of Ce3+and Ce4+. Introduction of Ce species can effectively extend the spectral response from UV to visible light region. N2adsorption-desorption analysis revealed that all the samples belong to mesoporous structure and have large BET surface area compared with P25. The CeOx/TiO2nanoparticles showed excellent photocatalytic activity in the degradation of MB under visible light irradiation.

Sign in / Sign up

Export Citation Format

Share Document