scholarly journals Preparation and Properties of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and Polypropylene Grafting Maleic Anhydride Two-Component Materials

2018 ◽  
Vol 26 (3(129)) ◽  
pp. 17-22 ◽  
Author(s):  
Xichao Sun ◽  
Yeqian Ge
Keyword(s):  
Maleic Anhydride ◽  
High Sensitivity ◽  
Crystal Form ◽  
Decomposition Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Two Component ◽  
Thermal Analyser ◽  
Thermal Stability Of

In order to provide a theoretical basis for the preparation and spinnability of two-component materials, poly(3-hydroxybutyrate-co-3-hydroxyvalerate)(PHBV) and polypropylene grafting maleic anhydride (PP-g-MAH) blends were prepared by melt mixing with different ratios (100/0, 75/25, 50/50, 25/75, 0/100). Properties of the blends system were investigated by means of a mixed rheometer, scanning electron microscope, simultaneous thermal analyser, differential scanning calorimetry and X-ray diffraction. The results demonstrate that PHBV/PP-g-MAH blends exhibit different morphology of the sea-island with a change in the mix ratio. The initial thermal decomposition temperature of PHBV in the blending system is over 250 °C, which means the thermal stability of PHBV is markedly improved. The crystallisation of PHBV varied according to the blending process parameter. When the cooling velocity increases, the crystallisation peak becomes wide, the temperature of crystallisation decreases, and the crystallisation temperature of PHBV increases significantly. PHBV has a high sensitivity to variation in the shear rate, and PHBV/PP-g-MAH blends have the mixing characteristic of shear thinned liquid. There is no diffraction peak at 2θ = 22.8°, and this result certifies that PP-g-MAH changes the crystal form of PHBV. and that PP-g-MAH addition is beneficial to the spinnability of PHBV. Results show that the interplay between PHBV and PP-g-MAH is of great significance and universal for both plastics and fibres.

scholarly journals Effect of Sr2TiMnO6 fillers on mechanical, dielectric and thermal behaviour of PMMA polymer

2015 ◽  
Vol 05 (03) ◽  
pp. 1550018 ◽  
Author(s):  
P. Thomas ◽  
B. S. Dakshayini ◽  
H. S. Kushwaha ◽  
Rahul Vaish
Keyword(s):  
Coefficient Of Thermal Expansion ◽  
Thermo Gravimetric Analysis ◽  
Mechanical Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Melt Mixing ◽  
Transition Formula ◽  
Thermal Stability Of ◽  
Pmma Polymer

Composites of poly(methyl methacrylate) (PMMA) and [Formula: see text] (STMO) were fabricated via melt mixing followed by hot pressing technique. These were characterized using X-ray diffraction (XRD), thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), thermo mechanical analysis (TMA) and impedance analyser for their structural, thermal and dielectric properties. The coefficient of thermal expansion (CTE) was measured between 40°C and 100°C for pure PMMA is 115.2 ppm/°C, which was decreased to 78.58 ppm/°C when the STMO content was increased to 50 wt.% in PMMA. There was no difference in the glass transition ([Formula: see text]) temperature of the PMMA polymer and their composites. However, the FTIR analysis indicated possible interaction between the PMMA and STMO. The density and the hardness were increased as the STMO content increased in the PMMA matrix. Permittivity was found to be as high as 30.9 at 100 Hz for the PMMA+STMO-50 wt.% composites, indicating the possibility of using these materials for capacitor applications. The thermal stability of polymer was enhanced by incorporation of STMO fillers.

Preparation, characterization, and properties of polystyrene/Na-montmorillonite composites

2018 ◽  
Vol 32 (8) ◽  
pp. 1078-1091 ◽  
Author(s):  
Sibel Erol Dağ ◽  
Pınar Acar Bozkurt ◽  
Fatma Eroğlu ◽  
Meltem Çelik
Keyword(s):  
Electron Microscopy ◽  
Interlayer Spacing ◽  
Decomposition Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Sem Images ◽  
Specific Pore Volume ◽  
Transmission Electron ◽  
Thermal Stability Of

A series of polystyrene (PS)/unmodified Na-montmorillonite (Na-MMT) composites were prepared via in situ radical polymerization. The prepared composites were characterized using various techniques. The presence of various functional groups in the unmodified Na-MMT and PS/unmodified Na-MMT composite was confirmed by Fourier transform infrared spectroscopy. Morphology and particle size of prepared composites was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). According to the XRD and TEM results, the interlayer spacing of MMT layers was expanded. SEM images showed a spongy and porous-shaped morphology of composites. TEM revealed the Na-MMT intercalated in PS matrix. The thermal stability of PS/unmodified Na-MMT composites was significantly improved as compared to PS, which is confirmed using thermogravimetric analysis (TGA). The TGA curves indicated that the decomposition temperature of composites is higher at 24–51°C depending on the composition of the mixture than that of pure PS. The differential scanning calorimetry (DSC) results showed that the glass transition temperature of composites was higher as compared to PS. The moisture retention, water uptake, Brunauer–Emmett–Teller specific surface area, and specific pore volume of composites were also investigated. Water resistance of the composites can be greatly improved.

Preparation and Characterization of Polypropylene/Clay Nanocomposites

2011 ◽  
Vol 55-57 ◽  
pp. 1584-1587 ◽  
Author(s):  
Li Mei Wang
Keyword(s):  
Xrd Analysis ◽  
Decomposition Temperature ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Xrd Pattern ◽  
Solution Blending ◽  
Clay Layers ◽  
Thermal Stability Of

Polypropylene(PP)/clay nanocomposites were prepared by solution blending. The microstructure of PP/clay nanocomposites was studied by wide-angle X-ray diffraction (XRD) analysis. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to investigate thermal properties of PP/clay nanocomposites. XRD pattern prove that clay layers were exfoliated into nanometer size in PP matrix and that α-Phase crystallite was the main crystallite of PP in PP/clay nanocomposites. TGA examinations confirmed that the maximum decomposition temperature of PP/clay nanocomposites was higher than that of neat PP and that the thermal stability of PP/clay nanocomposites rose noticeably. Results of DSC scans showed the crystalliztion temperature of nanocomposites was slightly bigger than that of pure PP due to the efficient nucleating effects of clay layers.

Effect of boric acid on thermal stability of poly (acrylonitrile-methyl acrylate)

e-Polymers ◽  
2009 ◽  
Vol 9 (1) ◽  
Author(s):  
Na Han ◽  
Xingxiang Zhang
Keyword(s):  
Thermal Stability ◽  
Boric Acid ◽  
Methyl Acrylate ◽  
Gel Permeation Chromatography ◽  
Decomposition Temperature ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Molar Ratios ◽  
Thermal Stability Of

AbstractA series of acrylonitrile(AN)-methyl acrylate (MA) copolymers (AN/MA) with molar ratios of 100/0-70/30 were synthesized by water depositing polymerization. One to three percent of boric acid (BA) was adopted as a stabilizer to enhance the thermal stability of AN/MA. The copolymers and the mixtures of copolymers treated with BA were characterized by using Fourier Transform Infrared Spectroscopy (FTIR), Nuclear Magnetic Resonance (1H NMR), Gel Permeation Chromatography (GPC), Differential Scanning Calorimetry (DSC), Thermogravimetry (TG), X-ray diffraction (XRD) and Optic Microscope. The results show that melting point (Tm), glass transition temperature (Tg) and crystallinity of the copolymer decreased while decomposition temperature (Td) increased with the increase of MA content. Tm of AN/MA dropped to 174 °C and Td rose up to 321 °C when 15 mol% MA was incorporated. It was worthy to note that Tm of the copolymers increased conspicuously after being treated with BA. Stability of AN/MA with a molar ratio of 85/15 containing 1 wt% BA improved remarkably. The mixture can be kept stable up to 30 min at 220 °C.

scholarly journals Synthesis and Characterization of N-Substituted Polyether-Block-Amide Copolymers

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 773
Author(s):  
Jyun-Yan Ye ◽  
Kuo-Fu Peng ◽  
Yu-Ning Zhang ◽  
Szu-Yuan Huang ◽  
Mong Liang
Keyword(s):  
Titanium Isopropoxide ◽  
Decomposition Temperature ◽  
Phenyl Isocyanate ◽  
Cross Linking ◽  
Resonance Spectroscopy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Degradation Temperature ◽  
Melt Polycondensation ◽  
Structural Regularity

A series of N-substituted polyether-block-amide (PEBA-X%) copolymers were prepared by melt polycondensation of nylon-6 prepolymer and polytetramethylene ether glycol at an elevated temperature using titanium isopropoxide as a catalyst. The structure, thermal properties, and crystallinity of PEBA-X% were investigated using nuclear magnetic resonance spectroscopy, Fourier-transform infrared spectroscopy, differential scanning calorimetry, wide angle X-ray diffraction, and thermogravimetric analysis. In general, the crystallinity, melting point, and thermal degradation temperature of PEBA-X% decreased as the incorporation of N-methyl functionalized groups increased, owing to the disruption caused to the structural regularity of the copolymer. However, in N-acetyl functionalized analogues, the crystallinity first dropped and then increased because of a new γ form arrangement that developed in the microstructure. After the cross-linking reaction of the N-methyl-substituted derivative, which has electron-donating characteristics, with poly(4,4′-methylenebis(phenyl isocyanate), the decomposition temperature of the resulting polymer significantly increased, whereas no such improvements could be observed in the case of the electro-withdrawing N-acetyl-substituted derivative, because of the incompleteness of its cross-linking reaction.

scholarly journals Structure and Properties of Polyoxymethylene/Silver/Maleic Anhydride-Grafted Polyolefin Elastomer Ternary Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1954
Author(s):  
Yang Liu ◽  
Xun Zhang ◽  
Quanxin Gao ◽  
Hongliang Huang ◽  
Yongli Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Maleic Anhydride ◽  
Ag Nanoparticles ◽  
Decomposition Temperature ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Maximum Value ◽  
Polyolefin Elastomer ◽  
Local Defects

In the present study, silver (Ag) nanoparticles and maleic anhydride-grafted polyolefin elastomer (MAH-g-POE) were used as enhancement additives to improve the performance of the polyoxymethylene (POM) homopolymer. Specifically, the POM/Ag/MAH-g-POE ternary nanocomposites with varying Ag nanoparticles and MAH-g-POE contents were prepared by a melt mixing method. The effects of the additives on the microstructure, thermal stability, crystallization behavior, mechanical properties, and dynamic mechanical thermal properties of the ternary nanocomposites were studied. It was found that the MAH-g-POE played a role in the bridging of the Ag nanoparticles and POM matrix and improved the interfacial adhesion between the Ag nanoparticles and POM matrix, owing to the good compatibility between Ag/MAH-g-POE and the POM matrix. Moreover, it was found that the combined addition of Ag nanoparticles and MAH-g-POE significantly enhanced the thermal stability, crystallization properties, and mechanical properties of the POM/Ag/MAH-g-POE ternary nanocomposites. When the Ag/MAH-g-POE content was 1 wt.%, the tensile strength reached the maximum value of 54.78 MPa. In addition, when the Ag/MAH-g-POE content increased to 15wt.%, the elongation at break reached the maximum value of 64.02%. However, when the Ag/MAH-g-POE content further increased to 20 wt.%, the elongation at break decreased again, which could be attributed to the aggregation of excessive Ag nanoparticles forming local defects in the POM/Ag/MAH-g-POE ternary nanocomposites. Furthermore, when the Ag/MAH-g-POE content was 20 wt.%, the maximum decomposition temperature of POM/Ag/MAH-g-POE ternary nanocomposites was 398.22 °C, which was 71.39 °C higher than that of pure POM. However, compared with POM, the storage modulus of POM/Ag/MAH-g-POE ternary nanocomposites decreased with the Ag/MAH-g-POE content, because the MAH-g-POE elastomer could reduce the rigidity of POM.

Structure and properties of polypropylene/organic rectorite nanocomposites

Clay Minerals ◽  
2009 ◽  
Vol 44 (1) ◽  
pp. 35-50 ◽  
Author(s):  
Yun Huang ◽  
Xiaoyan Ma ◽  
Guozheng Liang ◽  
Hongxia Yan
Keyword(s):  
Loss Modulus ◽  
Polarized Light ◽  
Clay Content ◽  
Crystal Form ◽  
Ammonium Bromide ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Monoclinic Crystal ◽  
X Ray

AbstractMelt blending using a twin-screw extruder was used to prepare composites of polypropylene (PP)/organic rectorite (PR). The organic rectorite (OREC) was modified with dodecyl benzyl dimethyl ammonium bromide (1227). Wide-angle X-ray diffraction (WAXD) and transmission electron microscopy were used to investigate the dispersion of OREC in the composites. The d spacings of OREC in PR composites was greater than in OREC itself. The dispersion of OREC particles in the PP polymer matrix was fine and uniform when the clay content was small (2 wt.%). The rheology was characterized using a capillary rheometer. The processing behaviour of the PR system improved as the amount of OREC added increased. Non-isothermal crystallization kinetics were analysed using differential scanning calorimetry. It was shown that the addition of OREC had a heterogeneous nucleation effect on PP, and can accelerate the crystallization. However, only when fine dispersion was achieved, and at lower rates of temperature decrease, was the crystallinity greater. Wide-angle X-ray diffraction and polarized light microscopy were used to observe the crystalline form and crystallite size. The PP in the PR composites exhibited an a-monoclinic crystal form, as in pure PP, and in both cases a spherulite structure was observed. However, the smaller spherulite size in the PR systems indicated that addition of OREC can reduce the crystal size significantly, which might improve the ‘toughness’ of the PP. The mechanical properties (tensile and impact strength) improved when the amount of OREC added was appropriate. Dynamic mechanical analysis showed that the storage modulus (E′) and loss modulus (E″) of the nanocomposites were somewhat greater than those of pure PP when an appropriate amount of OREC was added. Finally, thermogravimetric analysis showed that the PR systems exhibited a greater thermal stability than was seen with pure PP.

scholarly journals Green Preparation, Spheroidal, and Superior Property of Nano-1,3,5,7-Tetranittro-1,3,5,7-Tetrazocane

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Xinlei Jia ◽  
Jingyu Wang ◽  
Conghua Hou ◽  
Yingxin Tan
Keyword(s):  
Activation Energy ◽  
Particle Size ◽  
Fractal Dimension ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Fractal Theory ◽  
Crystal Form ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
The Impact

Herein, a green process for preparing nano-HMX, mechanical demulsification shearing (MDS) technology, was developed. Nano-HMX was successfully fabricated via MDS technology without using any chemical reagents, and the fabrication mechanism was proposed. Based on the “fractal theory,” the optimal shearing time for mechanical emulsification was deduced by calculating the fractal dimension of the particle size distribution. The as-prepared nano-HMX was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC). And the impact sensitivities of HMX particles were contrastively investigated. The raw HMX had a lower fractal dimension of 1.9273. The ideal shearing time was 7 h. The resultant nano-HMX possessed a particle size distribution ranging from 203.3 nm to 509.1 nm as compared to raw HMX. Nano-HMX particles were dense spherical, maintaining β-HMX crystal form. In addition, they had much lower impact sensitivity. However, the apparent activation energy as well as thermal decomposition temperature of nano-HMX particles was decreased, attributing to the reduced probability for hotspot generation. Especially when the shearing time was 7 h, the activation energy was markedly decreased.

scholarly journals Preparation and Characterization of Spherical Submicron CL-20 by Siphon Spray Refinement

2020 ◽  
Vol 2020 ◽  
pp. 1-9 ◽  
Author(s):  
Jiangtao Xing ◽  
Weili Wang ◽  
Wenzheng Xu ◽  
Tianle Yao ◽  
Jun Dong ◽  
...  
Keyword(s):  
Impact Sensitivity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Crystal Forms ◽  
Refined Method ◽  
Diffraction Angle ◽  
Ultrasonic Assisted ◽  
The Impact ◽  
Thermal Stability Of

In order to improve the safety of hexanitrohexaazaisowurtzitane (CL-20), submicron CL-20 particles were prepared by a siphon ultrasonic-assisted spray refining experimental device. The samples were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and differential scanning calorimetry (DSC), and the impact sensitivity of the samples was tested. The results show that the particle size of siphon-refined CL-20 is about 800 nm~1 μm, which is more smooth, mellow, and dense than that of CL-20 prepared by a traditional pressure-refined method. The peak diffraction angle of pressure- and siphon-refined CL-20 is basically the same as that of raw CL-20, and their crystal forms are ε type. The peak strength of pressure- and siphon-refined CL-20 decreased obviously. The apparent activation energy of pressure-refined CL-20 and siphon-refined CL-20 is 13.3 kJ/mol and 11.95 kJ/mol higher than that of raw CL-20, respectively. The thermal stability of CL-20 is improved. The activation enthalpy (ΔH#) is significantly higher than that of raw CL-20, and the characteristic drop is 70.4% and 82.7% higher than that of raw CL-20. The impact sensitivity of siphon-refined CL-20 is lower than that of pressure-refined CL-20, so the safety performance of an explosive is improved obviously.

scholarly journals Characterization of the Interface Between the Bulk Glass Forming Alloy Zr41Ti14Cu12Ni10Be23 with Pure Metals and Ceramics

2000 ◽  
Vol 15 (7) ◽  
pp. 1617-1621 ◽  
Author(s):  
Jan Schroers ◽  
Konrad Samwer ◽  
Frigyes Szuecs ◽  
William L. Johnson
Keyword(s):  
Sessile Drop ◽  
Bulk Glass ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Glass Forming ◽  
Processing Times ◽  
Thermal Stability Of

The reaction of the bulk glass forming alloy Zr41Ti14Cu12Ni10Be23 (Vit 1) with W, Ta, Mo, AlN, Al2O3, Si, graphite, and amorphous carbon was investigated. Vit 1 samples were melted and subsequently solidified after different processing times on discs of the different materials. Sessile drop examinations of the macroscopic wetting of Vit 1 on the discs as a function of temperature were carried out in situ with a digital optical camera. The reactions at the interfaces between the Vit 1 sample and the different disc materials were investigated with an electron microprobe. The structure and thermal stability of the processed Vit 1 samples were examined by x-ray diffraction and differential scanning calorimetry. The results are discussed in terms of possible applications for composite materials.

Sign in / Sign up

Export Citation Format

Share Document