scholarly journals Research on Optimising the Insulation of Footwear Materials Using Statistical Methods

2019 ◽  
Vol 27 (4(136)) ◽  
pp. 81-87 ◽  
Author(s):  
Wioleta Serweta ◽  
Małgorzata Matusiak ◽  
Katarzyna Ławińska
Keyword(s):  
Thermal Conductivity ◽  
Statistical Methods ◽  
Thermal Insulation ◽  
Outer Layer ◽  
Point Of View ◽  
Material Characteristics ◽  
Lining Material ◽  
Spacer Fabrics

In this paper, the results of research on the thermal insulation properties of textile and leather materials are presented. These materials were used in order to develop innovative footwear upper combinations with higher hygienic properties. Outer leather materials (L1, L2) and textile (T1, T2, T3, T4) were joined around the edges by stitching with leather lining materials (LG1a, LG1b, LG1c) and textiles. Moreover, the textile linings were divided into the following groups: spacer fabrics (TG2a, TG2b, TG2c), flat textiles (TG3a, TG3b, TG3c) and flat textiles based on bamboo fibres (TG4a, TG4b, TG4c, TG4d). In the next step of these investigations, the materials were joined in a two – layered composition, where for the outer layer was upper material, and for the inner – lining material. For these compositions, the thermal insulation properties were measured with the use of an Alambeta device. The following material characteristics were determined: thermal conductivity, resistance and absorptivity, which were the most important parameters from a hygienic point of view. The classification mentioned above was important from the manufacturer’s point of view because it gave a set of information about optimal upper material configurations. With respect to the results obtained, the best packages from the thermal insulation point of view were as follows: L2 – TG4b, L1 – TG4b, T1 – LG1a, T2 – TG4a, T3 – TG4a & T4 – LG1a.

scholarly journals Thermal-Insulation Properties of Multilayer Textile Packages

2014 ◽  
Vol 14 (4) ◽  
pp. 299-307 ◽  
Author(s):  
Małgorzata Matusiak ◽  
Sylwia Kowalczyk
Keyword(s):  
Thermal Conductivity ◽  
High Temperature ◽  
Thermal Insulation ◽  
Protective Clothing ◽  
Point Of View ◽  
Protective Efficiency ◽  
Knitted Fabrics ◽  
Textile Materials ◽  
Number Of Layers ◽  
Thermal Protective Clothing

Abstract Thermal-insulation properties of textile materials play a significant role in material engineering of protective clothing. Thermal-insulation properties are very important from the point of view of thermal comfort of the clothing user as well as the protective efficiency against low or high temperature. Thermal protective clothing usually is a multilayer construction. Its thermal insulation is a resultant of a number of layers and their order, as well as the thermalinsulation properties of a single textile material creating particular layers. The aim of the presented work was to investigate the relationships between the thermal-insulation properties of single materials and multilayer textile packages composed of these materials. Measurement of the thermal-insulation properties of single and multilayer textile materials has been performed with the Alambeta. The following properties have been investigated: thermal conductivity, resistance and absorptivity. Investigated textile packages were composed of two, three and four layers made of woven and knitted fabrics, as well as nonwovens. On the basis of the obtained results an analysis has been carried out in order to assess the dependency of the resultant values of the thermal-insulation properties of multilayer packages on the appropriate values of particular components.

scholarly journals Fique as a Sustainable Material and Thermal Insulation for Buildings: Study of Its Decomposition and Thermal Conductivity

2021 ◽  
Vol 13 (13) ◽  
pp. 7484
Author(s):  
Gabriel Fernando García Sánchez ◽  
Rolando Enrique Guzmán López ◽  
Roberto Alonso Gonzalez-Lezcano
Keyword(s):  
Thermal Conductivity ◽  
Thermal Decomposition ◽  
Thermal Insulation ◽  
Model Fitting ◽  
Good Alternative ◽  
Negative Effects ◽  
Thermal Insulator ◽  
Fitting Method ◽  
Thermogravimetric Data ◽  
Reduce Energy Consumption

Buildings consume a large amount of energy during all stages of their life cycle. One of the most efficient ways to reduce their consumption is to use thermal insulation materials; however, these generally have negative effects on the environment and human health. Bio-insulations are presented as a good alternative solution to this problem, thus motivating the study of the properties of natural or recycled materials that could reduce energy consumption in buildings. Fique is a very important crop in Colombia. In order to contribute to our knowledge of the properties of its fibers as a thermal insulator, the measurement of its thermal conductivity is reported herein, employing equipment designed according to the ASTM C 177 standard and a kinetic study of its thermal decomposition from thermogravimetric data through the Coats–Redfern model-fitting method.

scholarly journals Microstructure Dependence of Effective Thermal Conductivity of EB-PVD TBCs

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1838
Author(s):  
Shi-Yi Qiu ◽  
Chen-Wu Wu ◽  
Chen-Guang Huang ◽  
Yue Ma ◽  
Hong-Bo Guo
Keyword(s):  
Thermal Conductivity ◽  
Mechanical Stress ◽  
Effective Thermal Conductivity ◽  
Thermal Insulation ◽  
Inclination Angle ◽  
Physical Vapor Deposition ◽  
Thermal Contact ◽  
Mathematic Model ◽  
Columnar Structure ◽  
Structural Parameter

Microstructure dependence of effective thermal conductivity of the coating was investigated to optimize the thermal insulation of columnar structure electron beam physical vapor deposition (EB-PVD coating), considering constraints by mechanical stress. First, a three-dimensional finite element model of multiple columnar structure was established to involve thermal contact resistance across the interfaces between the adjacent columnar structures. Then, the mathematical formula of each structural parameter was derived to demonstrate the numerical outcome and predict the effective thermal conductivity. After that, the heat conduction characteristics of the columnar structured coating was analyzed to reveal the dependence of the effective thermal conductivity of the thermal barrier coatings (TBCs) on its microstructure characteristics, including the column diameter, the thickness of coating, the ratio of the height of fine column to coarse column and the inclination angle of columns. Finally, the influence of each microstructural parameter on the mechanical stress of the TBCs was studied by a mathematic model, and the optimization of the inclination angle was proposed, considering the thermal insulation and mechanical stress of the coating.

Bio-based Polyurethane-clay Nanocomposite Foams: Systheses and Properties

2009 ◽  
Vol 1188 ◽  
Author(s):  
Min Liu ◽  
Zoran S. Petrovic ◽  
Yijin Xu
Keyword(s):  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Cell Structure ◽  
Polyurethane Foams ◽  
Mechanical And Thermal Properties ◽  
Cell Content ◽  
Modified Clay ◽  
Rigid Polyurethane Foams ◽  
Nanocomposite Foams ◽  
Organically Modified

AbstractStarting from a bio-based polyol through modification of soybean oil, BIOH™ X-210, two series of bio-based polyurethanes-clay nanocomposite foams have been prepared. The effects of organically-modified clay types and loadings on foam morphology, cell structure, and the mechanical and thermal properties of these bio-based polyurethanes-clay nanocomposite foams have been studied with optical microscopy, compression test, thermal conductivity, DMA and TGA characterization. Density of nanocomposite foams decreases with the increase of clay loadings, while reduced 10% compressive stress and yield stress keep constant up to 2.5% clay loading in polyol. The friability of rigid polyurethane-clay nanocomposite foams is high than that of foam without clay, and the friability for nanofoams from Cloisite® 10A is higher than that from 30B at the same clay loadings. The incorporation of clay nanoplatelets decreases the cell size in nanocomposite foams, meanwhile increases the cell density; which would be helpful in terms of improving thermal insulation properties. All the nanocomposite foams were characterized by increased closed cell content compared with the control foam from X-210 without clay, suggesting the potential to improve thermal insulation of rigid polyurethane foams by utilizing organically modified clay. Incorporation of clay into rigid polyurethane foams results in the increase in glass transition temperature: the Tg increased from 186 to 197 to 204 °C when 30B concentration in X-210 increased from 0 to 0.5 to 2.5%, respectively. Even though the thermal conductivity of nanocomposite foams from 30B is lower than or equal to that of rigid polyurethane control foam from X-210, thermal conductivity of nanocomposite foams from 10A is higher than that of control at all 10A concentrations. The reason for this abnormal phenomenon is not clear at this moment; investigation on this is on progress.

Cryogenic thermal insulating and mechanical properties of rigid polyurethane foams blown with hydrofluoroolefin: Effect of perfluoroalkane

2021 ◽  
pp. 0021955X2110626
Author(s):  
Tae Seok Kim ◽  
Yeongbeom Lee ◽  
Chul Hyun Hwang ◽  
Kwang Ho Song ◽  
Woo Nyon Kim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Stability ◽  
Cell Size ◽  
Thermal Insulation ◽  
Coefficient Of Thermal Expansion ◽  
Lower Surface ◽  
Polyurethane Foams ◽  
Insulation Material ◽  
Pu Foams

The effect of perfluoroalkane (PFA) on the morphology, thermal conductivity, mechanical properties and thermal stability of rigid polyurethane (PU) foams was investigated under ambient and cryogenic conditions. The PU foams were blown with hydrofluorolefin. Morphological results showed that the minimum cell size (153 μm) was observed when the PFA content was 1.0 part per hundred polyols by weight (php). This was due to the lower surface tension of the mixed polyol solution when the PFA content was 1.0 php. The thermal conductivity of PU foams measured under ambient (0.0215 W/mK) and cryogenic (0.0179 W/mK at −100°C) conditions reached a minimum when the PFA content was 1.0 php. The low value of thermal conductivity was a result of the small cell size of the foams. The above results suggest that PFA acted as a nucleating agent to enhanced the thermal insulation properties of PU foams. The compressive and shear strengths of the PU foams did not appreciably change with PFA content at either −170°C or 20°C. However, it shows that the mechanical strengths at −170°C and 20°C for the PU foams meet the specification. Coefficient of thermal expansion, and thermal shock tests of the PU foams showed enough thermal stability for the LNG carrier’s operation temperature. Therefore, it is suggested that the PU foams blown by HFO with the PFA addition can be used as a thermal insulation material for a conventional LNG carrier.

Development and Research of Thermal Insulation Materials from Natural Fibres

2014 ◽  
Vol 604 ◽  
pp. 285-288 ◽  
Author(s):  
Saulius Vaitkus ◽  
Rūta Karpavičiūtė ◽  
Sigitas Vėjelis ◽  
Lina Lekūnaitė
Keyword(s):  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Preparation Method ◽  
Raw Materials ◽  
Natural Fibres ◽  
Current Work ◽  
Insulation Materials ◽  
Flax Fibres ◽  
Hemp Fibres

Natural fibres from flax and hemp are used as raw materials for efficient thermal insulation. In current work, tests were carried out using chopped and combed long flax fibres as well as chopped and combed long hemp fibres. Investigations have shown that thermal conductivity of natural fibres depends on their preparation method (combing, chopping) and materials density.

scholarly journals Graphene-Based Thermal Interface Materials: An Application-Oriented Perspective on Architecture Design

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1201 ◽  
Author(s):  
Le Lv ◽  
Wen Dai ◽  
Aijun Li ◽  
Cheng-Te Lin
Keyword(s):  
Thermal Conductivity ◽  
High Performance ◽  
Electronic Devices ◽  
Point Of View ◽  
Future Research ◽  
Thermal Interface Materials ◽  
Research Directions ◽  
Thermal Interface ◽  
Future Research Directions ◽  
Interface Materials

With the increasing power density of electrical and electronic devices, there has been an urgent demand for the development of thermal interface materials (TIMs) with high through-plane thermal conductivity for handling the issue of thermal management. Graphene exhibited significant potential for the development of TIMs, due to its ultra-high intrinsic thermal conductivity. In this perspective, we introduce three state-of-the-art graphene-based TIMs, including dispersed graphene/polymers, graphene framework/polymers and inorganic graphene-based monoliths. The advantages and limitations of them were discussed from an application point of view. In addition, possible strategies and future research directions in the development of high-performance graphene-based TIMs are also discussed.

scholarly journals Thermal insulation properties of green vacuum insulation panel using wood fiber as core material

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 3339-3351 ◽  
Author(s):  
Baowen Wang ◽  
Zhihui Li ◽  
Xinglai Qi ◽  
Nairong Chen ◽  
Qinzhi Zeng ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Bulk Density ◽  
Thermal Insulation ◽  
Wood Fiber ◽  
Core Material ◽  
High Porosity ◽  
Total Thermal Conductivity ◽  
Wood Fibers ◽  
Vacuum Insulation ◽  
Vacuum Insulation Panel

Wood fibers were prepared as core materials for a vacuum insulation panel (VIP) via a dry molding process. The morphology of the wood fibers and the microstructure, pore structure, transmittance, and thermal conductivity of the wood fiber VIP were tested. The results showed that the wood fibers had excellent thermal insulation properties and formed a porous structure by interweaving with one another. The optimum bulk density that led to a low-cost and highly thermally efficient wood fiber VIP was 180 kg/m3 to 200 kg/m3. The bulk density of the wood fiber VIP was 200 kg/m3, with a high porosity of 78%, a fine pore size of 112.8 μm, and a total pore volume of 7.0 cm3·g-1. The initial total thermal conductivity of the wood fiber VIP was 9.4 mW/(m·K) at 25 °C. The thermal conductivity of the VIP increased with increasing ambient temperature. These results were relatively good compared to the thermal insulation performance of current biomass VIPs, so the use of wood fiber as a VIP core material has broad application prospects.

scholarly journals The role of the time factor in the manager functions

2009 ◽  
Vol 3 (5-6) ◽  
pp. 101-108
Author(s):  
Éva Bácsné Bába
Keyword(s):  
Reaction Time ◽  
Statistical Methods ◽  
Time Management ◽  
Questionnaire Survey ◽  
Management Practice ◽  
Time Factor ◽  
Point Of View ◽  
Time Efficiency ◽  
Management Work

The role of the time factor in management is increasing. Change directs attention to the time factor from the point of view of the organisation,and management does the same from that of the person. I examined the time management practice of managers of organisations related to agribusiness, and the reaction time characterising the adaption ability of the organisations through a questionnaire survey. I analysed the collected data with scientifically established statistical methods. During studying resources, managing tasks, change, reaction time and effect I explored the features of time as resource, the significance of the time factor, the improvability of time efficiency in the different managing functions, the factors supporting and hindering the quick reaction of organisations, and what rearrangements can be seen in management work nowadays.

Sign in / Sign up

Export Citation Format

Share Document