Electric Bus Indoor Heat Balance in Cold Weather

The use of electric buses is increasing all over the world; this is due to the aim of limiting pollution in heavily urbanized areas. Using electric buses is one element of the desire to drop local pollution to zero emissions. The necessary electricity can be generated through centralized production, and in the case of electric buses, the pollution level is directly proportional to the amount of electricity produced. Their limited onboard power needs optimization, both in terms of traction and in auxiliary energy consumption. Heating in electric buses consumes the most energy from the auxiliaries, which can reduce the range of the vehicle up to a half, or more in the coldest days of the winter months. In this context, a precise estimation of heat loss and of the energy necessary for heating electric buses is crucial. Using the heat transfer theory, the heat balance method, and the U-value estimation, this article estimates the heat loss for a typical 12 m electric bus for a harsh winter day. Thermal simulations were made in order to estimate the heat flux through the structure of the bus (windows, walls, roof, and floor). Heat loss components were calculated in order to determine the most affected zones of the bus. The calculated data for the energy necessary to heat the bus were compared with the heating system data from an electric bus. By optimizing the necessary auxiliary energy consumption, the emissions at the source of electricity production will be significantly reduced.

Comparison of Heat Transfer Theory, CFD and Experimental Results in the Design Process of High-Power Fiber Laser Cooling Plate

For the stabilization of laser output power and wavelength of the high power fiber laser, the cooling plate must be properly taken into account. In this study, three analyzing methods which are heat transfer theory, CFD and experiment are used to analyze cooling plate performance by measuring pump Laser Diode(LD) temperature. Under limited operating conditions of a cooling plate, the internal flow of cooling plate is transitional flow so that the internal flow is assumed to be laminar and turbulence flow and conducted theoretical calculation. Through CFD, temperature of pump LD and characteristics of the internal flow were analyzed. By the experiment, temperature of pump LD was measured in real conditions and the performance of the cooling plate was verified. The results of this study indicate that three analyzing methods are practically useful to design the cooling plate for the high power fiber laser or similar things.

Heat transfer simulation in laser irradiated retinal tissues

A realistic model of human retinal tissues to simulate thermal performance of optical laser photocoagulation therapy is presented. The key criteria to validate the treatment effectiveness is to ensure the photocoagulation temperature between 60 and 70°C is reached in the treatment region of interest. The model presented consists of truncated volumes of the retinal pigment epithelium (RPE) and adjacent retinal tissues. Two cases of choroid pigmentation are modelled to signify extreme cases of human eye difference: albino and dark colour choroid pigmentation. Conditions for consistent heating over the irradiated treatment spot is modelled for laser beams with different intensity profiles: ‘top-hat’, Gaussian and ‘donut’ modes. The simulation considers both uniform heating within retinal tissue layers and spatial intensity decay due to absorption along the direction of laser propagation. For a 500 m spot, pulse length 100 ms and incident power to the cornea of 200 mW, realistic spatial variation in heating results in peak temperatures increasing within the RPE and shifting towards the choroid in the case of choroidal pigmentation. Finite element analysis methodology, where heat transfer theory governs the temperature evolution throughout tissues peripheral to the irradiated RPE is used to determine the zone of therapeutic benefit. While a TEM01 donut mode beam produces lower peak temperatures in the RPE for a given incident laser power, it reduces the volume of retinal tissue reaching excessive temperatures and maximises the zone of therapeutic benefit. Described are simulation limitations, boundary conditions, grid size and mesh growth factor required for realistic simulation.

Effects of operating and material parameters on the thermal characteristics of a wet clutch

Based on the frictional mechanism of a wet clutch, frictional models of wet clutch engagement were established using the modified Reynolds equation and the elastic contact model between frictional pairs. Then, the heat flux models for the viscous shear and asperity friction were built, and the two-dimensional transient thermal models for the separator plate, friction disk, and ATF heat convection model were deduced based on the heat transfer theory and conservation law of energy. Finally, the Runge–Kutta numerical method was used to solve the frictional and thermal models. The average temperature of the separator plate, friction disk, and ATF were calculated. The effects of operating and material parameters, such as applied pressure, initial angular velocity, friction lining permeability, surface combined roughness RMS, equivalent elastic modulus, and ATF flow, on the thermal characteristics of friction pairs and ATF during engagement, were studied. The simulation results show that the temperature characteristics of the separator plate, friction disk, and ATF depend mainly on the viscous shear and asperity friction heat flux, and that the operating and material parameters of the wet clutch also have significant impacts on the overall variation trend of the thermal characteristics of the separator plate, friction disk, and ATF.

Thermodynamic Simulation Modeling Analysis and Experimental Research of Vertical Ultrasonic Vibration Assisted EDM

Compared with traditional EDM, ultrasonic vibration assisted EDM ((UEDM)) shows better performance in machining efficiency and surface quality. But the material removal process of UEDM is complex, and there are many influencing factors, so it is difficult to describe the material removal process accurately. In this study, based on the voltage variation during UEDM processing and combined with the heat transfer theory, the material removal model of TC4 titanium alloy under the condition of single pulse vertical ultrasonic vibration UEDM was established, and the material removal process of UEDM under different amplitudes was analyzed. The machining efficiency and surface quality of UEDM with different ultrasonic energy under the condition of vertical ultrasonic vibration are obtained verified by UEDM experiments. The best ultrasonic energy under different current can be obtained by adjusting the current and ultrasonic vibration energy, which can improve the efficiency of UEDM.

Effects of the Solder Phase Transformation on the Optimization of Reflow Soldering Parameters and Temperature Profiles

In this study, a heat convection model of the reflow oven and a heat conduction model of the soldering area are proposed based on heat transfer theory, and a dynamic Thomas algorithm is developed for solving linear equations with coefficient matrix evolving over time in the tridiagonal system, which is derived from a heat transfer problem with moving boundaries in the solder phase transition process. We have also carried out numerical simulations for investigating the accuracy of the mathematical model, in which the temperature profiles are calculated and compared for different cases with considering or ignoring phase transformations, respectively. Parameters of reflow soldering, such as the conveyor speed, the set temperature in each zone, and a part of the heating factor, are optimized by the use of the nondominated sorting genetic algorithm II. By comparing the temperature profile and optimal solutions in the two cases, numerical results show that phase transitions of the solder have great impacts on optimal parameters and the slope of temperature profiles. Moreover, the phenomenon that the heating factor varies with the maximum set temperature in a banded distribution is investigated and analyzed, which is an important part of this work.

Cooling Performance and Thermal Radiation Model of Asphalt Mixture with Modified Infrared Powder

This research studied a new material named modified infrared powder (MIRP) for decreasing the high temperature of asphalt pavements which can help alleviate the urban heat island effect to some extent. Based on the physical apparent density tests of materials and infrared thermal radiation test, the cooling performance of MIRP was obtained. X-ray diffraction analysis and scanning electron microscopy test (SEM) were conducted to analyze the chemical composition and the microstructure of MIRP, respectively. According to the radiant heat transfer theory, a thermal radiation model of the pavement equilibrium temperature was established by microscopic and chemical analysis to study the influence of thermal radiation asphalt mixture and reveal its cooling performance. The results show that the main components of MIRP are metal oxides and nonmetallic oxides which improve its infrared emissivity. Compared with limestone mineral powder asphalt mortar, the asphalt mortar with MIRP had a more compact structure and uniform distribution, and enhanced the overall structural performance of the mixture. The thermal radiation model reveals that the pavement equilibrium temperature combined with the MIRP in asphalt mixture decreases with the increase of the longwave emissivity, and it diminishes with the decrease of the shortwave absorptivity.