scholarly journals Thermal Stability of Residual Stresses in Differently Deep Rolled Surface Layers of Steel SAE 1045

2021 ◽  
Author(s):  
Stephanie Saalfeld ◽  
Thomas Wegener ◽  
Berthold Scholtes ◽  
Thomas Niendorf
Keyword(s):  
Thermal Stability ◽  
Elevated Temperature ◽  
Residual Stresses ◽  
Elevated Temperatures ◽  
Fatigue Behavior ◽  
Decisive Role ◽  
Deep Rolling ◽  
Material Conditions ◽  
The Stability ◽  
Thermal Stability Of

AbstractThe stability of compressive residual stresses generated by deep rolling plays a decisive role on the fatigue behavior of specimens and components, respectively. In this regard, deep rolling at elevated temperature has proven to be very effective in stabilizing residual stresses when fatigue analysis is conducted at ambient temperature. However, since residual stresses can be affected not only by plastic deformation but also when thermal energy is provided, it is necessary to analyze the influence of temperature and time on the relaxation behavior of residual stresses at elevated temperature. To evaluate the effect of deep rolling at elevated temperatures on stability limits under thermal as well as combined thermo-mechanical loads, the present work introduces and discusses the results of investigations on the thermal stability of residual stresses in differently deep rolled material conditions of the steel SAE 1045.

Thermal Stability of Magnetic Properties in Dehydrogenated Triarylmethane Resins

1989 ◽  
Vol 173 ◽  
Author(s):  
Michiya Otani ◽  
Sugio Otani
Keyword(s):  
Thermal Stability ◽  
Magnetic Properties ◽  
Magnetic Property ◽  
Room Temperature ◽  
Permanent Magnets ◽  
Elevated Temperatures ◽  
Mechanical Response ◽  
The Stability ◽  
Thermal Stability Of

ABSTRACTThe stability of the magnetic properties of dehydrogenated triaryl-methane resins was investigated both at room temperature and at elevated temperatures. A magnetic property different from that reported in a previous paper was found in the course of studying the reproducibility of synthesis. This new property was examined through a mechanical response of the resins to a set of permanent magnets.

Effect of Bi Addition on Thermal Stability and Tensile Ductility of Mg-3%Zn-0.4%Zr Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 647-650
Author(s):  
Joong Hwan Jun ◽  
Min Ha Lee
Keyword(s):  
Thermal Stability ◽  
Tensile Strength ◽  
Elevated Temperature ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Tensile Ductility ◽  
Grain Structure ◽  
Hot Rolled ◽  
Thermal Stability Of ◽  
Zr Alloy

Thermal stability of  grains and tensile ductilities at room and elevated temperatures were investigated and compared for Mg-3%Zn-0.4%Zr and Mg-3%Zn-0.4%Zr-1%Bi alloys in hot-rolled state. The Bi-added alloy showed slightly finer-grained microstructure with enhanced thermal stability, which is closely associated with fine Mg-Bi compounds acting as obstacles for the migration of grain boundaries. The Mg-3%Zn-0.4%Zr-1%Bi alloy exhibited better tensile strength at room temperature and tensile ductilities at elevated temperature. Finer and more homogeneous grain structure with higher thermal stability would be responsible for the enhanced tensile properties in the Bi-added alloy.

scholarly journals Thermal stability and diffusion characteristics of ultrathin amorphous carbon films grown on crystalline and nitrogenated silicon substrates by filtered cathodic vacuum arc deposition

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shengxi Wang ◽  
Anurag Roy ◽  
Kyriakos Komvopoulos
Keyword(s):  
Thermal Stability ◽  
Amorphous Carbon ◽  
Silicon Substrate ◽  
Elevated Temperatures ◽  
Carbon Films ◽  
Vacuum Arc ◽  
Cross Sectional ◽  
Prolonged Heating ◽  
Filtered Cathodic Vacuum Arc ◽  
Thermal Stability Of

AbstractAmorphous carbon (a-C) films are widely used as protective overcoats in many technology sectors, principally due to their excellent thermophysical properties and chemical inertness. The growth and thermal stability of sub-5-nm-thick a-C films synthesized by filtered cathodic vacuum arc on pure (crystalline) and nitrogenated (amorphous) silicon substrate surfaces were investigated in this study. Samples of a-C/Si and a-C/SiNx/Si stacks were thermally annealed for various durations and subsequently characterized by high-resolution transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS). The TEM images confirmed the continuity and uniformity of the a-C films and the 5-nm-thick SiNx underlayer formed by silicon nitrogenation using radio-frequency sputtering. The EELS analysis of cross-sectional samples revealed the thermal stability of the a-C films and the efficacy of the SiNx underlayer to prevent carbon migration into the silicon substrate, even after prolonged heating. The obtained results provide insight into the important attributes of an underlayer in heated multilayered media for preventing elemental intermixing with the substrate, while preserving the structural stability of the a-C film at the stack surface. An important contribution of this investigation is the establishment of an experimental framework for accurately assessing the thermal stability and elemental diffusion in layered microstructures exposed to elevated temperatures.

scholarly journals Influence of Shot Peening on the Isothermal Fatigue Behavior of the Gamma Titanium Aluminide Ti-48Al-2Cr-2Nb at 750 °C

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1083
Author(s):  
Christoph Breuner ◽  
Stefan Guth ◽  
Elias Gall ◽  
Radosław Swadźba ◽  
Jens Gibmeier ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Shot Peening ◽  
Elevated Temperatures ◽  
Stress Amplitude ◽  
Negative Impact ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Fatigue Tests ◽  
Positive Effects ◽  
Isothermal Fatigue

One possibility to improve the fatigue life and strength of metallic materials is shot peening. However, at elevated temperatures, the induced residual stresses may relax. To investigate the influence of shot peening on high-temperature fatigue behavior, isothermal fatigue tests were conducted on shot-peened and untreated samples of gamma TiAl 48-2-2 at 750 °C in air. The shot-peened material was characterized using EBSD, microhardness, and residual stress analyses. Shot peening leads to a significant increase in surface hardness and high compressive residual stresses near the surface. Both effects may have a positive influence on lifetime. However, it also leads to surface notches and tensile residual stresses in the bulk material with a negative impact on cyclic lifetime. During fully reversed uniaxial tension-compression fatigue tests (R = −1) at a stress amplitude of 260 MPa, the positive effects dominate, and the fatigue lifetime increases. At a lower stress amplitude of 230 MPa, the negative effect of internal tensile residual stresses dominates, and the lifetime decreases. Shot peening leads to a transition from surface to volume crack initiation if the surface is not damaged by the shots.

scholarly journals Mechanical and thermal stability of retained austenite in plastically deformed bainite-based TRIP-aided medium-Mn steels

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Aleksandra Kozłowska ◽  
Adam Grajcar ◽  
Aleksandra Janik ◽  
Krzysztof Radwański ◽  
Ulrich Krupp ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Retained Austenite ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Mechanical Stability ◽  
Electron Backscatter Diffraction ◽  
Cost Effective ◽  
Tensile Tests ◽  
Thermal Stability Of

AbstractAdvanced medium-Mn sheet steels show an opportunity for the development of cost-effective and light-weight automotive parts with improved safety and optimized environmental performance. These steels utilize the strain-induced martensitic transformation of metastable retained austenite to improve the strength–ductility balance. The improvement of mechanical performance is related to the tailored thermal and mechanical stabilities of retained austenite. The mechanical stability of retained austenite was estimated in static tensile tests over a wide temperature range from 20 °C to 200 °C. The thermal stability of retained austenite during heating at elevated temperatures was assessed by means of dilatometry. The phase composition and microstructure evolution were investigated by means of scanning electron microscopy, electron backscatter diffraction, X-ray diffraction and transmission electron microscopy techniques. It was shown that the retained austenite stability shows a pronounced temperature dependence and is also stimulated by the manganese addition in a 3–5% range.

The effect of methyl and methoxy substituents on dianilines for a thermosetting polyimide system

2020 ◽  
Vol 32 (7) ◽  
pp. 801-822 ◽  
Author(s):  
John J La Scala ◽  
Greg Yandek ◽  
Jason Lamb ◽  
Craig M Paquette ◽  
William S Eck ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Molecular Weight ◽  
Glass Transition ◽  
Elevated Temperature ◽  
Methyl Substituent ◽  
Glass Transition Temperatures ◽  
High Performing ◽  
Methoxy Substituent ◽  
Acidic Conditions ◽  
Thermal Stability Of

4,4′-Methylenedianiline (MDA) is widely used in high-temperature polyimide resins, including polymerization of monomer reactants-15. The toxicity of MDA significantly limits the manufacturability using this resin. Modifying the substitution and electronics of MDA could allow for the reduction of toxicity while maintaining the high-performing properties of the materials derived from the modified MDA. The addition of a single methyl substituent, methoxy substituent, location of these substituents, and location of the amine relative to the phenolic bridge were modified as were other non-aniline diamines. Various anilines were condensed with paraformaldehyde under acidic conditions to yield dianilines. These dianilines and diamines were reacted with nadic anhydride and 3,3′,4,4′-benzophenonetetracarboxylic dianhydride in methanol to form the polyamic acid oligomers and heated at elevated temperature to form polyimide oligomers. It was found that the molecular weight of the oligomers derived from MDA alternatives was generally lower than that of MDA oligomers resulting in lower glass transition temperatures ( T gs) and degradation temperatures. Additionally, methoxy substituents further reduce the T g of the polymers versus methyl substituents and reduce the thermal stability of the resin. Methyl-substituted alternatives produced polyimides with similar T gs and degradation temperatures. The toxicity of the MDA alternatives was examined. Although a few were identified with reduced toxicities, the alternatives with properties similar to that of MDA also had high toxicities.

Intrinsic Thermal Stability of Anisotropic Thin-Film Superconductors

1990 ◽  
Vol 112 (1) ◽  
pp. 10-15 ◽  
Author(s):  
M. I. Flik ◽  
C. L. Tien
Keyword(s):  
Thin Film ◽  
Thermal Stability ◽  
Stability Criterion ◽  
High Temperature Superconductors ◽  
Stability Criteria ◽  
Anisotropic Thermal Conductivity ◽  
Operating Current ◽  
Released Energy ◽  
The Stability ◽  
Thermal Stability Of

Intrinsic thermal stability denotes a situation where a superconductor can carry the operating current without resistance at all times after the occurrence of a localized release of thermal energy. This novel stability criterion is different from the cryogenic stability criteria for magnets and has particular relevance to thin-film superconductors. Crystals of ceramic high-temperature superconductors are likely to exhibit anisotropic thermal conductivity. The resultant anisotropy of highly oriented films of superconductors greatly influences their thermal stability. This work presents an analysis for the maximum operating current density that ensures intrinsic stability. The stability criterion depends on the amount of released energy, the Biot number, the aspect ratio, and the ratio of the thermal conductivities in the plane of the film and normal to it.

Thermal Breakdown Kinetics of 1-Ethyl-3-Methylimidazolium Ethylsulfate Measured Using Quantitative Infrared Spectroscopy

2017 ◽  
Vol 71 (12) ◽  
pp. 2626-2631 ◽  
Author(s):  
Jeffrey L. Wheeler ◽  
McKinley Pugh ◽  
S. Jake Atkins ◽  
Jason M. Porter
Keyword(s):  
Thermal Stability ◽  
Room Temperature ◽  
Computational Models ◽  
Elevated Temperatures ◽  
Molar Absorptivity ◽  
Ir Absorption ◽  
Optical Cell ◽  
Multiple Samples ◽  
Kinetics Of ◽  
Thermal Stability Of

In this work, the thermal stability of the room temperature ionic liquid (RTIL) 1-ethyl-3-methylimidazolium ethylsulfate ([EMIM][EtSO4]) is investigated using infrared (IR) spectroscopy. Quantitative IR absorption spectral data are measured for heated [EMIM][EtSO4]. Spectra have been collected between 25 ℃ and 100 ℃ using a heated optical cell. Multiple samples and cell pathlengths are used to determine quantitative values for the molar absorptivity of [EMIM][EtSO4]. These results are compared to previous computational models of the ion pair. These quantitative spectra are used to measure the rate of thermal decomposition of [EMIM][EtSO4] at elevated temperatures. The spectroscopic measurements of the rate of decomposition show that thermogravimetric methods overestimate the thermal stability of [EMIM][EtSO4].

Isothermal Fatigue Behavior and Damage Modeling of a High Temperature Woven PMC

1999 ◽  
Vol 122 (1) ◽  
pp. 62-68 ◽  
Author(s):  
A. L. Gyekenyesi
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Fatigue Behavior ◽  
Stiffness Degradation ◽  
Fatigue Properties ◽  
Residual Compressive Strength ◽  
Stiffness Reduction ◽  
Fatigue Damage Accumulation ◽  
Strength Tests

This study focuses on the fully reversed fatigue behavior exhibited by a carbon fiber/polyimide resin woven laminate at room and elevated temperatures. Nondestructive video edge view microscopy and destructive sectioning techniques were used to study the microscopic damage mechanisms that evolved. The elastic stiffness was monitored and recorded throughout the fatigue life of the coupon. In addition, residual compressive strength tests were conducted on fatigue coupons with various degrees of damage as quantified by stiffness reduction. Experimental results indicated that the monotonic tensile properties were only minimally influenced by temperature, while the monotonic compressive and fully reversed fatigue properties displayed greater reductions due to the elevated temperature. The stiffness degradation, as a function of cycles, consisted of three stages; a short-lived high degradation period, a constant degradation rate segment covering the majority of the life, and a final stage demonstrating an increasing rate of degradation up to failure. Concerning the residual compressive strength tests at room and elevated temperatures, the elevated temperature coupons appeared much more sensitive to damage. At elevated temperatures, coupons experienced a much larger loss in compressive strength when compared to room temperature coupons with equivalent damage. The fatigue damage accumulation law proposed for the model incorporates a scalar representation for damage, but admits a multiaxial, anisotropic evolutionary law. The model predicts the current damage (as quantified by residual stiffness) and remnant life of a composite that has undergone a known load at temperature. The damage/life model is dependent on the applied multiaxial stress state as well as temperature. Comparisons between the model and data showed good predictive capabilities concerning stiffness degradation and cycles to failure. [S0742-4795(00)01001-2]

scholarly journals Change in the stability of goat milk and cow milk due to pH and heat

2021 ◽  
Vol 233 ◽  
pp. 02046
Author(s):  
Xiaoxue Fan ◽  
Ming Cheng ◽  
Xiaoning Zhang ◽  
Cunfang Wang ◽  
Hua Jiang
Keyword(s):  
Thermal Stability ◽  
Milk Production ◽  
Ph Value ◽  
Goat Milk ◽  
Cow Milk ◽  
Type B ◽  
Fresh Milk ◽  
Ph Conditions ◽  
The Stability ◽  
Thermal Stability Of

This paper aimed to evaluate the changes in the thermal stability of goat milk, cow milk and homogenized milk under different pH conditions. The results showed that goat milk was of type B milk, and the thermal stability were positively correlated with the pH value. But cow milk was of type A milk, the most stable pH of fresh milk was 6.9, while it was 6.7 for homogenized cow milk. Compared with cow milk, the acidification of goat milk was stronger due to heat. Therefore, in the process of milk production, the germicidal heating conditions of two different milk sources should be determined according to their thermal stability.

Sign in / Sign up

Export Citation Format

Share Document