scholarly journals Effect of molecular carbon structures on the evolution of the pores and strength of lignite briquette coal with different heating rates

Fuel ◽  
2022 ◽  
Vol 307 ◽  
pp. 121917
Author(s):  
Qingqing Gan ◽  
Jiang Xu ◽  
Shoujian Peng ◽  
Fazhi Yan ◽  
Ruifang Wang ◽  
...  
Keyword(s):  
Heating Rates ◽  
Carbon Structures

Comparing fast inductive tempering and conventional tempering: Effects on microstructure and mechanical properties

2018 ◽  
Vol 115 (4) ◽  
pp. 407 ◽  
Author(s):  
Annika Eggbauer Vieweg ◽  
Gerald Ressel ◽  
Peter Raninger ◽  
Petri Prevedel ◽  
Stefan Marsoner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Energy ◽  
Charpy Impact ◽  
Heat Treating ◽  
Processing Route ◽  
High Heating Rate ◽  
Heating Rates ◽  
High Heating ◽  
Tempering Treatment ◽  
Carbide Distribution

Induction heating processes are of rising interest within the heat treating industry. Using inductive tempering, a lot of production time can be saved compared to a conventional tempering treatment. However, it is not completely understood how fast inductive processes influence the quenched and tempered microstructure and the corresponding mechanical properties. The aim of this work is to highlight differences between inductive and conventional tempering processes and to suggest a possible processing route which results in optimized microstructures, as well as desirable mechanical properties. Therefore, the present work evaluates the influencing factors of high heating rates to tempering temperatures on the microstructure as well as hardness and Charpy impact energy. To this end, after quenching a 50CrMo4 steel three different induction tempering processes are carried out and the resulting properties are subsequently compared to a conventional tempering process. The results indicate that notch impact energy raises with increasing heating rates to tempering when realizing the same hardness of the samples. The positive effect of high heating rate on toughness is traced back to smaller carbide sizes, as well as smaller carbide spacing and more uniform carbide distribution over the sample.

Non-Isothermal Decomposition Kinetic of Polypropylene/Hydrotalcite Composite

2019 ◽  
Vol 19 (11) ◽  
pp. 7493-7501 ◽  
Author(s):  
Sheng Xu ◽  
Min Zhang ◽  
Siyu Li ◽  
Moyu Yi ◽  
Shigen Shen ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Thermal Decomposition ◽  
Nitrogen Atmosphere ◽  
Heating Rates ◽  
Decomposition Reactions ◽  
Kinetic And Thermodynamic Parameters ◽  
Málek Method ◽  
Boundary Reaction ◽  
Phase Boundary Reaction ◽  
Thermal Stability Of

P3O5-10 pillared Mg/Al hydrotalcite (HTs) as a functional fire-retarding filler was successfully prepared by impregnation-reconstruction, where the HTs was used to prepare polypropylene (PP) and HTs composite (PP/HTs). Thermal decomposition was crucial for correctly identifying the thermal behavior for the PP/HTs, and studied using thermogravimetry (TG) at different heating rates. Based on single TG curves and Málek method, as well as 41 mechanism functions, the thermal decompositions of the PP/HTs composite and PP in nitrogen atmosphere were studied under non-isothermal conditions. The mechanism functions of the thermal decomposition reactions for the PP/HTs composite and PP were separately “chemical reaction F3” and “phase boundary reaction R2,” which were also in good agreement with corresponding experimental data. It was found that the addition of the HTs increased the apparent activation energy Ea of the PP/HTs comparing to the PP, which improved the thermal stability of the polypropylene. A difference in the set of kinetic and thermodynamic parameters was also observed between the PP/HTs and PP, particularly with respect to lower ΔS≠ value assigned to higher thermal stability of the PP/HTs composite.

An Investigation on Devolatilization Characteristics of Pulverized Corn Stalk at Flash Heating Rates

2004 ◽  
Author(s):  
Weiming ◽  
YI. ◽  
Xueyuan ◽  
BAI. ◽  
Zhihe ◽  
...  
Keyword(s):  
Corn Stalk ◽  
Heating Rates

scholarly journals State-of-the-Art Char Production with a Focus on Bark Feedstocks: Processes, Design, and Applications

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 87
Author(s):  
Ali Umut Şen ◽  
Helena Pereira
Keyword(s):  
State Of The Art ◽  
Lignocellulosic Materials ◽  
Heating Rates ◽  
Production Methods ◽  
Slow Pyrolysis ◽  
Production Studies ◽  
Lignocellulosic Feedstocks ◽  
Thermochemical Method ◽  
Superior Surface ◽  
First Time

In recent years, there has been a surge of interest in char production from lignocellulosic biomass due to the fact of char’s interesting technological properties. Global char production in 2019 reached 53.6 million tons. Barks are among the most important and understudied lignocellulosic feedstocks that have a large potential for exploitation, given bark global production which is estimated to be as high as 400 million cubic meters per year. Chars can be produced from barks; however, in order to obtain the desired char yields and for simulation of the pyrolysis process, it is important to understand the differences between barks and woods and other lignocellulosic materials in addition to selecting a proper thermochemical method for bark-based char production. In this state-of-the-art review, after analyzing the main char production methods, barks were characterized for their chemical composition and compared with other important lignocellulosic materials. Following these steps, previous bark-based char production studies were analyzed, and different barks and process types were evaluated for the first time to guide future char production process designs based on bark feedstock. The dry and wet pyrolysis and gasification results of barks revealed that application of different particle sizes, heating rates, and solid residence times resulted in highly variable char yields between the temperature range of 220 °C and 600 °C. Bark-based char production should be primarily performed via a slow pyrolysis route, considering the superior surface properties of slow pyrolysis chars.

TiO2 as a gas sensor: the novel carbon structures and noble metals as new elements for enhancing sensitivity – A Review

2021 ◽  
Author(s):  
Evelyn Alves Nunes Simonetti ◽  
Thais Cardoso de Oliveira ◽  
Ádamo Enrico do Carmo Machado ◽  
Amanda Alvarenga Coutinho Silva ◽  
Alan Silva dos Santos ◽  
...  
Keyword(s):  
Gas Sensor ◽  
Noble Metals ◽  
The Novel ◽  
Carbon Structures

scholarly journals Co-Combustion Studies of Low-Rank Coal and Refuse-Derived Fuel: Performance and Reaction Kinetics

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3796
Author(s):  
Mudassar Azam ◽  
Asma Ashraf ◽  
Saman Setoodeh Setoodeh Jahromy ◽  
Sajjad Miran ◽  
Nadeem Raza ◽  
...  
Keyword(s):  
Activation Energy ◽  
Waste Management ◽  
Energy Demand ◽  
Power Plants ◽  
Combustion Process ◽  
Isoconversional Methods ◽  
Low Rank ◽  
Heating Rates ◽  
Average Activation Energy ◽  
Refuse Derived Fuel

In connection to present energy demand and waste management crisis in Pakistan, refuse-derived fuel (RDF) is gaining importance as a potential co-fuel for existing coal fired power plants. This research focuses on the co-combustion of low-quality local coal with RDF as a mean to reduce environmental issues in terms of waste management strategy. The combustion characteristics and kinetics of coal, RDF, and their blends were experimentally investigated in a micro-thermal gravimetric analyzer at four heating rates of 10, 20, 30, and 40 °C/min to ramp the temperature from 25 to 1000 °C. The mass percentages of RDF in the coal blends were 10%, 20%, 30%, and 40%, respectively. The results show that as the RDF in blends increases, the reactivity of the blends increases, resulting in lower ignition temperatures and a shift in peak and burnout temperatures to a lower temperature zone. This indicates that there was certain interaction during the combustion process of coal and RDF. The activation energies of the samples were calculated using kinetic analysis based on Kissinger–Akahira–Sunnose (KAS) and Flynn–Wall–Ozawa (FWO), isoconversional methods. Both of the methods have produced closer results with average activation energy between 95–121 kJ/mol. With a 30% refuse-derived fuel proportion, the average activation energy of blends hit a minimum value of 95 kJ/mol by KAS method and 103 kJ/mol by FWO method.

scholarly journals Understanding the Links between the Composition-Processing-Properties in New Formulations of HEAs Sintered by SPS

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 888
Author(s):  
Paula Alvaredo-Olmos ◽  
Jon Molina-Aldareguía ◽  
Alvaro Vaz-Romero ◽  
Estela Prieto ◽  
Jesús González-Julián ◽  
...  
Keyword(s):  
High Hardness ◽  
Processing Parameters ◽  
Heating Rates ◽  
High Entropy ◽  
Plasma Sintering ◽  
Mechanical Study ◽  
Spark Plasma ◽  
Processing Properties ◽  
Bcc Phase ◽  
Hardness Values

This work presents two new compositions of high entropy alloys (HEAs) that were designed with the aim of obtaining a body-centered cubic (BCC) phase with high hardness values and a moderate density. Sintering was performed using Spark Plasma Sintering (SPS) with different heating rates to determine the influence of the processing parameters on the phase formation. The microstructural study revealed that the presence of Ni in the composition promoted phase separation, and the mechanical study confirmed a clear influence on the mechanical properties of both the composition and heating rate. The combination of microscopy with compression and nanoindentation tests at room and high temperature made it possible to advance our understanding of the relationships between the composition, processing, and properties of this emerging group of alloys.

Sign in / Sign up

Export Citation Format

Share Document