scholarly journals Experimental study on the influence of locked-in stress on the uniaxial compressive strength and elastic modulus of rocks

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Xin Liu ◽  
Hansheng Geng ◽  
Hongfa Xu ◽  
Yinhao Yang ◽  
Linjian Ma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Uniaxial Compression ◽  
Testing Machine ◽  
Peak Strength ◽  
Test Block ◽  
Compression Tests ◽  
Inclusion Content ◽  
Rubber Particles ◽  
Ground Stress

Abstract The rock contains many inclusions which produce high locked-in stress under the ground stress. In order to study the influence of locked-in stress on the mechanical properties of rocks, the rock-like materials and nitrile rubber particles are used to make a test block of the rock-like model which contains inclusions. The rubber particles will expand as the test block is heated, which creates locked-in stress in the inclusions. Uniaxial compression tests of similar model blocks with different locked-in stresses and different inclusion contents were performed by using a water bath and MTS-5T uniaxial compression testing machine. The results show that the peak strength and elastic modulus decreased with the increasement of locked-in stress and inclusion content. In the meantime, the relationship among the peak strength, the elastic modulus of the test piece, the locked-in stress and the inclusion content were obtained with the help of a mathematical fitting analysis of the quantitative formula. Furthermore, the expression and value curve of the joint impact factor are calculated. This paper evaluates the importance of the locked-in stress in the mechanical properties of the rock-like material and provide a guide for other researchers to further investigate the locked-in stress in rocks.

Experimental study and numerical simulation of uniaxial compression on artificial rock samples with Z-shaped fractures

2021 ◽  
Author(s):  
Tao Zhou ◽  
Haijun Chen ◽  
Liangxiao Xiong ◽  
Zhongyuan Xu ◽  
Jie Yang ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Crack Length ◽  
Uniaxial Compression ◽  
Inclination Angle ◽  
Failure Surface ◽  
Peak Strength ◽  
Particle Flow Code ◽  
Compression Tests ◽  
Failure Characteristics ◽  
Change Trend

Abstract To study the influence of the inclination and length of Z-shaped fissures on the mechanical properties and failure characteristics of the rock mass, this study conducts a series of uniaxial compression tests on rock-like materials with prefabricated Z-shaped fractures. In addition, two-dimensional Particle Flow Code software is used to perform uniaxial compression numerical simulations. The results show that when the specified inclination angle γ (γ = 0°, 30° or 45°) of the parallel cracks on both sides remains unchanged, the peak strength and elastic modulus of the sample show an M-shaped change trend with an increase in the inclination angle β of the middle connection crack. When γ = 60° or 90°, however, the peak strength and elastic modulus of the sample show a trend of decreasing, increasing, and then decreasing as β increases. In addition, the peak strength and elastic modulus of the sample decrease with an increase in the crack length. The influence of crack length on the elastic modulus is less than that of compressive strength. Further, the main failure mode of specimens with Z-shaped cracks is determined to be tension–shear mixed failure manifested by crack propagation from the tip of the prefabricated crack to the upper and lower boundaries of the sample. As a result, a through failure surface is formed with the prefabricated crack, which destroys the sample.

scholarly journals Experimental and Numerical Investigation of Failure Characteristics and Mechanism of Granites with Different Joint Angles

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Zhenhua Wang ◽  
Jun Fang ◽  
Gang Wang ◽  
Yifan Jiang ◽  
Dongwei Li
Keyword(s):  
Elastic Modulus ◽  
Uniaxial Compression ◽  
Elastic Strain Energy ◽  
Peak Stress ◽  
Peak Strength ◽  
Particle Flow Code ◽  
Dissipated Energy ◽  
Shear Cracks ◽  
Compression Tests ◽  
Dip Angle

The uniaxial compression tests were conducted on granite samples with different joint dip angles to more favorably explore the influences of the nonconsecutive joint on mechanical properties and deformation characteristics of the rock mass. The stress-strain curves, deformation and strength characteristics, and energy evolution process of the samples were analyzed. Numerical simulation using particle flow code (PFC) is employed to study the crack propagation process. The mode of jointed and fractured rock was investigated. The research results showed a significant reduction in both the peak strength and elastic modulus of jointed samples compared with intact ones: the peak strength and elastic modulus drop to the minimum at the joint dip angle of about 45°, especially for the peak strength, which takes up about 55% of the intact samples. The fractured samples’ total energy, elastic strain energy, and dissipated energy during the uniaxial compression drop significantly relative to intact samples. The proportion of the fracture modes varies with different joint dip angles, in which the ratio of shear cracks grows at first and then declines, with the highest balance at the dip angle of 45°. The damage stress’s sensitivity to the dip angle change is greater than that of the peak stress, with reduction amplitude more extensive than the latter.

scholarly journals Uniaxial Experimental Study of the Deformation Behavior and Energy Evolution of Conjugate Jointed Rock Based on AE and DIC Methods

2020 ◽  
Vol 2020 ◽  
pp. 1-16
Author(s):  
Jiliang Pan ◽  
Xu Wu ◽  
Qifeng Guo ◽  
Xun Xi ◽  
Meifeng Cai
Keyword(s):  
Stress Field ◽  
Uniaxial Compression ◽  
Testing Machine ◽  
Peak Strength ◽  
Image Correlation ◽  
Compression Tests ◽  
Dissipation Energy ◽  
Included Angle ◽  
Natural Rock ◽  
Ae Counts

Conjugate joint is one of the most common joint forms in natural rock mass, which is produced by different tectonic movements. To better understand the preexisting flaws, it is necessary to investigate joint development and its effect on the deformation and strength of the rock. In this study, uniaxial compression tests of granite specimens with different conjugate joints distribution were performed using the GAW-2000 compression-testing machine system. The PCI-2 acoustic emission (AE) testing system was used to monitor the acoustic signal characteristics of the jointed specimens during the entire loading process. At the same time, a 3D digital image correlation (DIC) technique was used to study the evolution of stress field before the peak strength at different loading times. Based on the experimental results, the deformation and strength characteristics, AE parameters, damage evolution processes, and energy accumulation and dissipation properties of the conjugate jointed specimens were analyzed. It is considered that these changes were closely related to the angle between the primary and secondary joints. The results show that the AE counts can be used to characterize the damage and failure of the specimen during uniaxial compression. The local stress field evolution process obtained by the DIC can be used to analyze the crack initiation and propagation in the specimen. As the included angle increases from 0° to 90°, the elastic modulus first decreases and then increases, and the accumulative AE counts of the peak first increase and then decrease, while the peak strength does not change distinctly. The cumulative AE counts of the specimen with an included angle of 45° rise in a ladder-like manner, and the granite retains a certain degree of brittle failure characteristics under the axial loading. The total energy, elastic energy, and dissipation energy of the jointed specimens under uniaxial compression failure were significantly reduced. These findings can be regarded as a reference for future studies on the failure mechanism of granite with conjugate joints.

scholarly journals Evaluation of remodeling and geometry on the biomechanical properties of nacreous bivalve shells

2022 ◽  
Vol 12 (1) ◽  
Author(s):  
Estefano Muñoz-Moya ◽  
Claudio M. García-Herrera ◽  
Nelson A. Lagos ◽  
Aldo F. Abarca-Ortega ◽  
Antonio G. Checa ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Uniaxial Compression ◽  
Shell Length ◽  
Biomechanical Properties ◽  
Material Behavior ◽  
Stress And Strain ◽  
Wave Forces ◽  
Compression Tests ◽  
Shell Size

AbstractMollusks have developed a broad diversity of shelled structures to protect against challenges imposed by biological interactions(e.g., predation) and constraints (e.g., $$pCO_2$$ p C O 2 -induced ocean acidification and wave-forces). Although the study of shell biomechanical properties with nacreous microstructure has provided understanding about the role of shell integrity and functionality on mollusk performance and survival, there are no studies, to our knowledge, that delve into the variability of these properties during the mollusk ontogeny, between both shells of bivalves or across the shell length. In this study, using as a model the intertidal mussel Perumytilus purpuratus to obtain, for the first time, the mechanical properties of its shells with nacreous microstructure; we perform uniaxial compression tests oriented in three orthogonal axes corresponding to the orthotropic directions of the shell material behavior (thickness, longitudinal, and transversal). Thus, we evaluated whether the shell material’s stress and strain strength and elastic modulus showed differences in mechanical behavior in mussels of different sizes, between valves, and across the shell length. Our results showed that the biomechanical properties of the material building the P. purpuratus shells are symmetrical in both valves and homogeneous across the shell length. However, uniaxial compression tests performed across the shell thickness showed that biomechanical performance depends on the shell size (aging); and that mechanical properties such as the elastic modulus, maximum stress, and strain become degraded during ontogeny. SEM observations evidenced that compression induced a tortuous fracture with a delamination effect on the aragonite mineralogical structure of the shell. Findings suggest that P. purpuratus may become vulnerable to durophagous predators and wave forces in older stages, with implications in mussel beds ecology and biodiversity of intertidal habitats.

scholarly journals Formation conditions and mechanical properties of aggregates produced in tephra–water–snow flows

2020 ◽  
Vol 72 (1) ◽  
Author(s):  
Hirofumi Niiya ◽  
Kenichi Oda ◽  
Daisuke Tsuji ◽  
Hiroaki Katsuragi
Keyword(s):  
Mechanical Properties ◽  
Mixing Time ◽  
Testing Machine ◽  
Small Scale ◽  
Scaling Analysis ◽  
Compression Tests ◽  
Ice Slurry ◽  
Experimental Conditions ◽  
Formation Conditions ◽  
Snow And Ice

Abstract The formation of aggregates consisting of snow, water, and tephra has been reported in small-scale experiments on three-phase flows containing tephra, water, and snow, representing lahars triggered by snowmelt. Such aggregates reduce the mobility of mud flow. However, the formation mechanism of such aggregates under various conditions has not been investigated. To elucidate the formation conditions and mechanical properties of the aggregates, we performed mixing experiments with materials on a rotating table and compression tests on the resulting aggregates with a universal testing machine in a low-temperature room at $$0\,^{\circ }\text {C}$$ 0 ∘ C . From experiments with varying component ratios of the mixture and tephra diameter, the following results were obtained: (i) the aggregate grew rapidly and reached maturity after a mixing time of 5 min; (ii) the mass of aggregates increased with snow concentration, exhibiting an approximately linear relationship; (iii) single aggregates with large mass formed at lower and higher tephra concentrations, whereas multiple aggregates with smaller mass were observed at intermediate concentrations; (iv) the shape of the aggregate satisfied the similarity law for an ellipsoid; (v) the compressive mechanical behavior could be modeled by an empirical nonlinear model. The obtained mechanical properties of the aggregates were independent of the experimental conditions; (vi) scaling analysis based on the Reynolds number and the strength of the aggregates showed that the aggregates cannot form in ice-slurry lahars. Our findings suggest that low-speed lahars containing snow and ice are likely to generate aggregates, but snow and ice in the ice-slurry lahars are dispersed without such aggregates.

scholarly journals Evaluation Method of Granite Multiscale Mechanical Properties Based on Nanoindentation Technology

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Man Lei ◽  
Fa-ning Dang ◽  
Haibin Xue ◽  
Mingming He
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Uniaxial Compression ◽  
Compression Test ◽  
Evaluation Method ◽  
Poisson Ratio ◽  
Nanoindentation Test ◽  
Uniaxial Compression Test ◽  
Displacement Curve ◽  
Mineral Contents

In order to study the mechanical properties of granite at the micro- and nanoscale, the load-displacement curve, residual indentation information, and component information of the quartz, feldspar, and mica in granite were obtained using a nanoindentation test, a scanning electron microscope (SEM), and X-ray diffraction (XRD). The elastic modulus and the hardness of each component of the granite were obtained through statistical analysis. Treating rock as a composite material, the relation between the macro- and microscopic mechanical properties of rock was established through the theory of micromechanical homogenization. The transition from micromechanical parameters to macromechanical parameters was realized. The equivalent elastic modulus and Poisson’s ratio of the granite were obtained by the Self-consistent method, the Dilute method, and the Mori-Tanaka method. Compared with the elastic modulus and the Poisson ratio of granites measured by a uniaxial compression test and the available data, the applicability of the three methods were analyzed. The results show that the elastic modulus and hardness of the quartz in the granite is the largest, the feldspar is the second, the mica is the smallest. The main mineral contents in granite were analyzed using the semiquantitative method by XRD and the rock slice identification test. The elastic modulus and the Poisson ratio of granite calculated by three linear homogenization methods are consistent with those of the uniaxial compression test. After comparing the calculation results of the three methods, it is found that the Mori-Tanaka method is more suitable for studying the mechanical properties of rock materials. This method has an important theoretical significance and practical value for studying the quantitative relationship between macro- and micromechanical indexes of brittle materials. The research results provide a new method and an important reference for studying the macro-, micro-, and nanomechanical properties of rock.

scholarly journals Predicting the Mechanical Properties of Bimrocks with High Rock Block Proportions Based on Resonance Testing Technology and Damage Theory

2019 ◽  
Vol 9 (17) ◽  
pp. 3537
Author(s):  
Yuexiang Lin ◽  
Limin Peng ◽  
Mingfeng Lei ◽  
Xiang Wang ◽  
Chengyong Cao
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Constitutive Model ◽  
Uniaxial Compression ◽  
Rock Block ◽  
Dynamic Elastic Modulus ◽  
Parameter Determination ◽  
Design Parameters ◽  
Damage Theory ◽  
Design And Construction

Block-in-matrix-rocks (bimrocks) are very complicated geological masses that cause many challenging problems during the design and construction of engineering projects, such as parameter determination and landsliding. Successful engineering design and construction depends on a suitable constitutive model and reliable design parameters for geological masses. In this paper, the vibration attenuation signal of welded bimrocks was obtained and studied using resonance test technology. Combined with a uniaxial compression test, a constitutive model was proposed to describe the mechanical behavior of welded bimrocks. On this basis, the relations between the dynamic elastic modulus and the physical parameters of bimrocks were established, which included macroscopic mechanical parameters and damage constitutive parameters. Consequently, a new technological process was proposed to provide quick identification of the mechanical properties of welded bimrocks. The results indicate that the dynamic elastic modulus is highly correlated with the rock block proportion (RBP) and uniaxial compression strength (UCS). It is an effective parameter to predict the strength of the bimrocks with high RBPs. Additionally, the proposed constitutive model, which is based on damage theory, can accurately simulate the strain softening behavior of the bimrocks. Combining the resonant frequency technology and the proposed constitutive model, the complete stress strain curve can be obtained in a rapid and accurate manner, which provides a further guarantee of the stability and safety of underground engineering.

scholarly journals Energy Dissipation-Based Method for Strength Determination of Rock under Uniaxial Compression

2020 ◽  
Vol 2020 ◽  
pp. 1-13 ◽  
Author(s):  
M. M. He ◽  
F. Pang ◽  
H. T. Wang ◽  
J. W. Zhu ◽  
Y. S. Chen
Keyword(s):  
Yield Strength ◽  
Uniaxial Compression ◽  
Peak Strength ◽  
Dissipated Energy ◽  
Compression Tests ◽  
Dissipation Energy ◽  
Evolution Characteristics ◽  
Deformation Properties ◽  
Energy Coefficient ◽  
The Stability

The energy conversion in rocks has an important significance for evaluation of the stability and safety of rock engineering. In this paper, some uniaxial compression tests for fifteen different rocks were performed. The evolution characteristics of the total energy, elastic energy, and dissipated energy for the fifteen rocks were studied. The dissipation energy coefficient was introduced to study the evolution characteristics of rock. The evolution of the dissipation energy coefficient for different rocks was investigated. The linear interrelations of the dissipation energy coefficients and the yield strength and peak strength were explored. The method was proposed to determine the strength of rock using the dissipation energy coefficients. The results show that the evolution of the dissipation energy coefficient exhibits significant deformation properties of rock. The dissipation energy coefficients linearly increase with the compaction strength, but decrease with the yield strength and peak strength. Moreover, the dissipation energy coefficient can be used to determine the rock burst proneness and crack propagation in rocks.

Experimental Investigation into the Influences of Weathering on the Mechanical Properties of Sedimentary Rocks

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Xiaoshuang Li ◽  
Yingchun Li ◽  
Saisai Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Friction Coefficient ◽  
Uniaxial Compression ◽  
Sedimentary Rocks ◽  
Uniaxial Tensile ◽  
Mechanical Parameters ◽  
Uniaxial Tensile Strength ◽  
Weathering Grades

The time-dependent behaviors of the sedimentary rocks which refer to the altering of the mechanical and deformable properties of rock elements in the long-term period are of increasing importance in the investigation of the failure mechanism of the rock strata in underground coal mines. In order to obtain the accurate and reliable mechanical parameters of the sedimentary rocks at different weathering grades, the extensive experimental programs including the Brazilian splitting test, uniaxial compression tests, and direct shear tests have been carried out on the specimens that exposed to the nature environments at different durations. The correlation between the weathering grades and mechanical parameters including uniaxial tensile strength, uniaxial compression strength, elastic modulus, Poisson’s ratio, cohesion, and friction coefficient was proposed. The obtained results suggested that uniaxial tensile strength, uniaxial compressive strength, elastic modulus, and cohesion dramatically decreased with increasing weathering time, characterized as the negative exponential relationship in general. The influences of various weathering grades on fracture behavior of the rock specimens were discussed. The cumulative damage of the rock by the weathering time decreased the friction coefficient of the specimens which led to the initiation and propagation of microcrack within the rock at lower stress conditions. The obtained results improved the understanding of the roles of weathering on the mechanical properties of sedimentary rocks, which is helpful in the design of the underground geotechnical structures.

Sign in / Sign up

Export Citation Format

Share Document