scholarly journals Design and optimisation of magnetically-tunable hybrid piezoelectric-triboelectric energy harvester

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Satish Rao Ganapathy ◽  
Hanim Salleh ◽  
Mohammad Khairul Azwan Azhar
Keyword(s):  
Low Power ◽  
Peak Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Frequency Range ◽  
Design Factor ◽  
Voltage Generation ◽  
Future Work ◽  
Design Factors ◽  
Extension Length

AbstractThe demand for energy harvesting technologies has been increasing over the years that can be attributed to its significance to low power applications. One of the key problems associated with the available vibration-based harvester is the maximum peak power can only be achieved when the device frequency matches the source frequency to generate low usable power. Therefore, in this study, a magnetically-tunable hybrid piezoelectric-triboelectric energy harvester (MT-HPTEH) was designed and optimised. Four key design factors: mass placement, triboelectric surface area, extension length and magnetic stiffness were investigated and optimised. The voltage generation from piezoelectric and triboelectric mechanisms was determined individually to understand the effect of each design factor on the mechanisms. An output power of 659 µW at 180 kΩ at 44 Hz was obtained from the optimised MT-HPTEH with a theoretical–experimental discrepancy of less than 10%. The added magnetically-tunable feature enabled the harvester to work at the desired frequency range with an open circuit voltage between 7.800 and 20.314 V and a frequency range from 38 to 54 Hz. This MT-HPTEH can power at least six wireless sensor networks and can be used for low power applications such as RFID tags. Future work may include designing of energy-saving and sustainable harvester.

Performance comparison between dual cantilevered and touch based hybridized triboelectric harvesters

2021 ◽  
Vol 15 (1) ◽  
pp. 7754-7761
Author(s):  
Satish Rao Ganapathy ◽  
H. Salleh
Keyword(s):  
Low Power ◽  
Surface Area ◽  
Peak Power ◽  
Energy Harvester ◽  
Dissimilar Materials ◽  
Performance Comparison ◽  
Effective Length ◽  
Surface Charges ◽  
Generate Surface ◽  
Power Outputs

The demand for energy harvesting technologies has been increasing over the years attributed to its significance to low power applications. One of the key problems associated with the vibration-based harvester is the fact that these harvesters generate low usable power while maximum peak power can only be attained when the device frequency matches the source frequency. In this study, triboelectric mechanism was investigated in combination with the piezoelectric mechanism in order to enhance the performance of the harvester. Triboelectric mechanism functions in a way that two dissimilar materials were placed in contact and then separated in order to generate surface charges and electric potential between them. Main design factors such as materials, surface area, structure, effective length, and etc. play a significant part in the enhancement of the performance. This study proposed two distinct designs of dual cantilevered structure and touch-based triboelectric energy harvester and evaluated the efficiency of the output between both structures. In addition, the effect of extension and surface area of triboelectric materials was investigated while the influence of these factors on the performance of the harvester was evaluated. The highest value of peak power obtained for dual cantilevered hybrid harvester was 650 µW across a load of 160 kΩ and frequency of 26 Hz. On the other hand, touch-based energy harvester produced an output peak power of 1220 µW across a load of 400 kΩ at 25 Hz. Achieving these power outputs may be able to power up electronics such as smartwatches, hearing aid and etc. Future studies on reliable low power applications to further advance the green power technology will be investigated.

scholarly journals A Low Power AC/DC Interface for Wind-Powered Sensor Nodes

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1823
Author(s):  
Mohammad Haidar ◽  
Hussein Chible ◽  
Corrado Boragno ◽  
Daniele D. Caviglia
Keyword(s):  
Low Power ◽  
Power Supply ◽  
Energy Harvester ◽  
Optimization Techniques ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Constant Voltage ◽  
Interface Circuit ◽  
Switching Converter ◽  
Input Signals

Sensor nodes have been assigned a lot of tasks in a connected environment that is growing rapidly. The power supply remains a challenge that is not answered convincingly. Energy harvesting is an emerging solution that is being studied to integrate in low power applications such as internet of things (IoT) and wireless sensor networks (WSN). In this work an interface circuit for a novel fluttering wind energy harvester is presented. The system consists of a switching converter controlled by a low power microcontroller. Optimization techniques on the hardware and software level have been implemented, and a prototype is developed for testing. Experiments have been done with generated input signals resulting in up to 67% efficiency for a constant voltage input. Other experiments were conducted in a wind tunnel that showed a transient output that is compatible with the target applications.

Performance analysis of a lever piezoelectric energy harvester for roadway applications

2021 ◽  
pp. 1045389X2110014
Author(s):  
Guangya Ding ◽  
Hongjun Luo ◽  
Jun Wang ◽  
Guohui Yuan
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Traffic Load ◽  
Energy Harvesters ◽  
Speed Sensor ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Self Powered ◽  
Output Characteristics

A novel lever piezoelectric energy harvester (LPEH) was designed for installation in an actual roadway for energy harvesting. The model incorporates a lever module that amplifies the applied traffic load and transmits it to the piezoelectric ceramic. To observe the piezoelectric growth benefits of the optimized LPEH structure, the output characteristics and durability of two energy harvesters, the LPEH and a piezoelectric energy harvester (PEH) without a lever, were measured and compared by carrying out piezoelectric performance tests and traffic model experiments. Under the same loading condition, the open circuit voltages of the LPEH and PEH were 20.6 and 11.7 V, respectively, which represents a 76% voltage increase for the LPEH compared to the PEH. The output power of the LPEH was 21.51 mW at the optimal load, which was three times higher than that of the PEH (7.45 mW). The output power was linearly dependent on frequency and load, implying the potential application of the module as a self-powered speed sensor. When tested during 300,000 loading cycles, the LPEH still exhibited stable structural performance and durability.

Design Optimization of Low Power and Low Frequency Vibration Based MEMS Energy Harvester

2013 ◽  
Vol 475-476 ◽  
pp. 1624-1628
Author(s):  
Hasnizah Aris ◽  
David Fitrio ◽  
Jack Singh
Keyword(s):  
Low Power ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Geometry Optimization ◽  
Low Frequency ◽  
Substrate Thickness ◽  
Power Harvesting ◽  
Low Frequency Vibration ◽  
Length Width ◽  
Development And Utilization

The development and utilization of different structural materials, optimization of the cantilever geometry and power harvesting circuit are the most commonly methods used to increase the power density of MEMS energy harvester. This paper discusses the cantilever geometry optimization process of low power and low frequency of bimorph MEMS energy harvester. Three piezoelectric materials, ZnO, AlN and PZT are deposited on top and bottom of the cantilever Si substrate. This study focuses on the optimization of the cantilevers length, width, substrate thickness and PZe thickness in order to achieve lower than 600 Hz of resonant frequency. The harvested power for this work is in the range of 0.02 ~ 194.49 nW.

Reverse Electrowetting-on-Dielectric Energy Harvesting Integrated With Charge Amplifier and Rectifier for Self-Powered Motion Sensors

2020 ◽  
Author(s):  
Pashupati R. Adhikari ◽  
Nishat T. Tasneem ◽  
Dipon K. Biswas ◽  
Russell C. Reid ◽  
Ifana Mahbub
Keyword(s):  
Energy Harvester ◽  
Schottky Diodes ◽  
Boost Converter ◽  
Motion Sensor ◽  
Motion Sensors ◽  
Frequency Range ◽  
Charge Amplifier ◽  
Electrowetting On Dielectric ◽  
Dc Voltage ◽  
Self Powered

Abstract This paper presents a reverse electrowetting-on-dielectric (REWOD) energy harvester integrated with rectifier, boost converter, and charge amplifier that is, without bias voltage, capable of powering wearable sensors for monitoring human health in real-time. REWOD has been demonstrated to effectively generate electrical current at a low frequency range (< 3 Hz), which is the frequency range for various human activities such as walking, running, etc. However, the current generated from the REWOD without external bias source is insufficient to power such motion sensors. In this work, to eventually implement a fully self-powered motion sensor, we demonstrate a novel bias-free REWOD AC generation and then rectify, boost, and amplify the signal using commercial components. The unconditioned REWOD output of 95–240 mV AC is generated using a 50 μL droplet of 0.5M NaCl electrolyte and 2.5 mm of electrode displacement from an oscillation frequency range of 1–3 Hz. A seven-stage rectifier using Schottky diodes having a forward voltage drop of 135–240 mV and a forward current of 1 mA converts the generated AC signal to DC voltage. ∼3 V DC is measured at the boost converter output, proving the system could function as a self-powered motion sensor. Additionally, a linear relationship of output DC voltage with respect to frequency and displacement demonstrates the potential of this REWOD energy harvester to function as a self-powered wearable motion sensor.

scholarly journals Ultra-Low Frequency Eccentric Pendulum-Based Electromagnetic Vibrational Energy Harvester

Micromachines ◽  
2020 ◽  
Vol 11 (11) ◽  
pp. 1009
Author(s):  
Mingxue Li ◽  
Huichao Deng ◽  
Yufeng Zhang ◽  
Kexin Li ◽  
Shijie Huang ◽  
...  
Keyword(s):  
Low Power ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Low Frequency ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Center Frequency ◽  
Vibration Energy ◽  
Outer Side ◽  
Working Frequency

With the development of low-power technology in electronic devices, the wireless sensor network shows great potential in applications in health tracing and ocean monitoring. These scenarios usually contain abundant low-frequency vibration energy, which can be collected through appropriate energy conversion architecture; thus, the common issue of limited battery life in wireless sensor devices could be solved. Traditional energy-converting structures such as the cantilever-beam type or spring-mass type have the problem of high working frequency. In this work, an eccentric pendulum-based electromagnetic vibration energy harvester is designed, analyzed, and verified with the finite element analysis method. The pendulum that contains alternative distributed magnets in the outer side works as a rotor and has the advantages of a simple structure and low center frequency. The structure size is well scalable, and the optimal output performance can be obtained by optimizing the coil thickness and width for a given diameter of the energy harvester. The simulation results show that the energy harvester could work in ultra-low frequencies of 0.2–3.0 Hz. A full-scale prototype of the energy harvester is manufactured and tested. The center working frequency is 2.0 Hz with an average output power of 8.37 mW, which has potential for application in driving low-power wireless sensor nodes.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

Sign in / Sign up

Export Citation Format

Share Document