scholarly journals Production of antipollutant mask with bamboo based carbon activated using H3PO4 and K2CO3

2018 ◽  
Vol 67 ◽  
pp. 03041
Author(s):  
Mahmud Sudibandriyo ◽  
Shobrun Jamil
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Dip Coating ◽  
Raw Material ◽  
Bet Surface Area ◽  
Cellulose Content ◽  
Pollution Problem ◽  
Gas Mask ◽  
Safety Limit ◽  
High Cellulose

The increase of developing countries’ economic level has led to increase in air pollution problem. This research aims to make activated carbon based gas mask filter that was prepared from bamboo scraps by the combined activation using H3PO4 and K2CO3.Bamboo was selected as raw material because of its abundant availability and high cellulose content (42.4-53.6%).Dip coating was conducted to coat activated carbon on the surface layer of mask by adding TEOS compound.Furthermore, adsorption capacity of activated carbon was tested using compartment by flowing air containing CO and CO2 for one hour. The results of the characterization shows that the iodine number of the activated carbon produced reaches 916.3 mg/g with BET surface area of 465.2 m2/g. SEM-EDX analysis shows that the carbon content is 74.83%wt.Adsorption capacity of activated carbon was tested using compartment by flowing air containing pollutant gas and compressed air for one hour. The results indicate that the maximum number of moles CO2 adsorbed is 4.8 mmol/g with 7 hour saturated time,while adsorption capacity of CO measured in 1 hour test is 0.103 mmol/g. Therefore, activated carbon has met the standards and can be applied for gas mask filter to eliminate CO and CO2 until below safety limit concentration.

scholarly journals Production of antipollutan mask based activated carbon from wasted coconut shell

2018 ◽  
Vol 154 ◽  
pp. 01005 ◽  
Author(s):  
Fauzan Nazif ◽  
Mahmud Sudibandriyo
Keyword(s):  
Air Pollution ◽  
Activated Carbon ◽  
Lignin Content ◽  
Raw Material ◽  
Coconut Shell ◽  
Cellulose Content ◽  
Good Material ◽  
Carbon Mass ◽  
Selection Of ◽  
Made In

Indonesia is one of the countries with the highest levels of air pollution in the world. Air pollution in Indonesia, especially in Jakarta due to the number of private vehicles increased at least 10% every year. This air pollution can have an impact on public health. One effort to do as a protection of people health is to use a mask. Activated carbon can be coated to mask in order to improve the effectiveness in reducing the pollutants. One good material used as material for activated carbon is coconut shell. Selection of coconut shell as the raw material of activated carbon is also based on cellulose content of 26.06%, hemicellulose content 27.07% and a lignin content of 29.40% in the dry state. This research was done in some variation such as activation methods, activated carbon mass, and adhesive material types. Based on pollutants adsorption test, mask with 6 grams of activated carbon, chemically activated, and used TEOS as adhesive is the best variation that able to adsorb as much 76,25% of CO2 Pollutants. Mask made in this research, has saturation time as long as 4 hours under high CO2 concentration.

Physicochemical Properties of Carbons Prepared from Physic Nut Waste by Phosphoric Acid and Potassium Hydroxide Activations

2007 ◽  
Vol 561-565 ◽  
pp. 1719-1722 ◽  
Author(s):  
Chiravoot Pechyen ◽  
Duangdao Aht-Ong ◽  
Duangduen Atong ◽  
Viboon Sricharoenchaikul
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Physicochemical Properties ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Potassium Hydroxide ◽  
Bet Surface Area ◽  
Physic Nut ◽  
Monolayer Adsorption ◽  
Adsorption Data

Char derived from pyrolysis of physic nut waste at 400-800°C was used for the preparation of activated carbon by chemical impregnation of phosphoric acid and potassium hydroxide. The original char exhibited the BET surface area in the range of 120-250 m2·g-1. The surface area increased to 480 and 532 m2·g-1 when activated with H3PO4 and KOH, respectively. Equilibrium adsorption data was found to be best represented by the Langmuir isotherm with maximum monolayer adsorption capacity of 560.13 mg·g-1 at 30°C. The adsorption capacity of the physic nut residue activated carbon was comparable to commercial activated carbon.

SURFACE PROPERTIES AND CATALYTIC PERFORMANCE OF ACTIVATED CARBON FIBERS SUPPORTED TiO2 PHOTOCATALYST

2008 ◽  
Vol 15 (04) ◽  
pp. 337-344 ◽  
Author(s):  
HUIFEN YANG ◽  
PINGFENG FU
Keyword(s):  
Activated Carbon ◽  
Carbon Fibers ◽  
Uv Light ◽  
Three Dimensional ◽  
Catalytic Performance ◽  
Dip Coating ◽  
Bet Surface Area ◽  
Activated Carbon Fibers ◽  
Organic Silicon ◽  
Acrylate Copolymer

Activated carbon fibers supported TiO 2 photocatalyst ( TiO 2/ACF) in felt-form was successfully prepared with a dip-coating process using organic silicon modified acrylate copolymer as a binder followed by calcination at 500°C in a stream of Ar gas. The photocatalyst was characterized by SEM, XRD, XPS, FTIR, and BET surface area. Most of carbon fibers were coated with uniformly distributed TiO 2 clusters of nearly 100 nm. The loaded TiO 2 layer was particulate for the organic binder in the compact film was carbonized. According to XPS and FTIR analysis, amorphous silica in carbon grains was synthesized after carbonizing organic silicon groups, and the Ti – O – Si bond was formed between the interface of loaded TiO 2 and silica. Additionally, the space between adjacent carbon fibers still remained unfilled after TiO 2 coating, into which both UV light and polluted solutions could penetrate to form a three-dimensional environment for photocatalytic reactions. While loaded TiO 2 amount increased to 456 mg TiO 2/1 g ACF, the TiO 2/ACF catalyst showed its highest photocatalytic activity, and this activity only dropped about 10% after 12 successive runs, exhibiting its high fixing stability of coated TiO 2.

scholarly journals Single-Stage Microwave-Assisted Coconut-Shell-Based Activated Carbon for Removal of Dichlorodiphenyltrichloroethane (DDT) from Aqueous Solution: Optimization and Batch Studies

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Azrina Aziz ◽  
Mohamad Nasran Nasehir Khan ◽  
Mohamad Firdaus Mohamad Yusop ◽  
Erniza Mohd Johan Jaya ◽  
Muhammad Azan Tamar Jaya ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Radiation Power ◽  
Total Pore Volume ◽  
Single Stage ◽  
Coconut Shell ◽  
Bet Surface Area ◽  
Adsorption System ◽  
Average Pore ◽  
Preparation Conditions

This research aims to optimize preparation conditions of coconut-shell-based activated carbon (CSAC) and to evaluate its adsorption performance in removing POP of dichlorodiphenyltrichloroethane (DDT). The CSAC was prepared by activating the coconut shell via single-stage microwave heating under carbon dioxide, CO2 flow. The total pore volume, BET surface area, and average pore diameter of CSAC were 0.420 cm3/g, 625.61 m2/g, and 4.55 nm, respectively. The surface of CSAC was negatively charged shown by the zeta potential study. Response surface methodology (RSM) revealed that the optimum preparation conditions in preparing CSAC were 502 W and 6 min for radiation power and radiation time, respectively, which corresponded to 84.83% of DDT removal and 37.91% of CSAC’s yield. Adsorption uptakes of DDT were found to increase with an increase in their initial concentration. Isotherm study revealed that DDT-CSAC adsorption system was best described by the Langmuir model with monolayer adsorption capacity, Qm of 14.51 mg/g. The kinetic study confirmed that the pseudo-second-order model fitted well with this adsorption system. In regeneration studies, the adsorption efficiency had slightly dropped from 100% to 83% after 5 cycles. CSAC was found to be economically feasible for commercialization owing to its low production cost and high adsorption capacity.

scholarly journals Activated carbon and biochar from pineapple waste biomass for the removal of methylene blue

2021 ◽  
Vol 1 (1) ◽  
pp. 30-36
Author(s):  
Khoirun Nisa Mahmud ◽  
Tan Hui Wen ◽  
Zainul Akmar Zakaria
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Water System ◽  
Raw Material ◽  
Waste Biomass ◽  
Adsorbent Dosage ◽  
Pineapple Waste ◽  
Area Functional ◽  
Dye Pollution

Dye pollution in water system is of concern due to its carcinogenicity and its effect on aesthetic feature. One pollutant of interest is methylene blue (MB), which is a cationic dye widely used in industries. In this study, pyrolysis process was used to convert pineapple waste biomass (PWB) into useful adsorbents such as biochar (BC) and activated carbon (AC) to remove MB in water. BC was produced from pyrolysis of PWB (340 °C, 3 hours) whereas AC was prepared from pyrolysis of PWB (500 °C, 1 hour) impregnated with zinc chloride (ZnCl2). Prior to use, AC-PWB and BC-PWB were characterized for surface area, functional groups and surface morphology. Removal of MB was investigated by varying different parameters i.e. initial MB concentration and contact time, adsorbent dosage and temperature. Results obtained showed that AC-PWB has higher adsorption capacity than BC-PWB. The adsorption capacity and adsorption rate increased with increasing initial concentration of MB, adsorbent dosage and temperature until reached equilibrium condition. As a conclusion, PWB can be used as a useful raw material to produce cheap and environmentally friendly adsorbent to remove dye from solution.

scholarly journals Adsorption Ability of Cephalexin onto the Straw-Based Activated Carbon: Performance and Mechanism

2020 ◽  
Vol 32 (8) ◽  
pp. 2084-2090
Author(s):  
Lam Van Tan ◽  
Hong-Tham Nguyen Thi ◽  
To-Uyen Dao Thi ◽  
Nguyen Thi Thuy Hong
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Bet Surface Area ◽  
Surface Material ◽  
Adsorption Ability ◽  
Initial Concentration ◽  
Carbon Performance ◽  
Adsorbent Materials ◽  
Performance And Mechanism

A straw-activated carbon has been successfully synthesized with the high BET surface area, at 494.9240 m2/g, which is perfectly suitable for the adsorption of cephalexin antibiotic from aqueous water. It is noted that the adsorption capacity of straw-activated carbon is demonstrated by the effect of initial concentration, contact time, pH solution and dosage. The straw-activated carbon exhibited improved decontaminant efficiency towards cephalexin antibiotics. Quick and improved sorption could be attributable to the distinctive structural and compositional merits as well as the synergetic contribution of functional groups to surface material. Most interestingly, the adsorption capacity achieved at pH 6 was ~98.52%. A mechanism adsorption has been proposed to demonstrate adsorption of the straw-activated carbon (AC-S). By comparison with other studies, it is confirmed that AC-S in this study obtained a higher removal efficiency than other adsorbent materials, suggesting that straw-activated carbon may be an appropriate candidate to treat cephalexin from wastewater media

scholarly journals Preparation and characterization of activated carbon from bio-diesel by-products (Jatropha seedcake) by steam activation

2012 ◽  
Vol 47 (3) ◽  
pp. 257-264
Author(s):  
MS Islam ◽  
MA Rouf ◽  
S Fujimoto ◽  
T Minowa
Keyword(s):  
Activated Carbon ◽  
Structural Changes ◽  
Pyrolysis Temperature ◽  
Hold Time ◽  
Raw Material ◽  
Bet Surface Area ◽  
Activation Process ◽  
Steam Activation ◽  
Activation Temperature ◽  
Ft Ir

Activated carbon was prepared using bio-diesel waste (Jatropha seedcake) by conventional carbonization followed by steam activation process on a laboratory scale. Preliminary tests were conducted to investigate the influences of different operating parameters, such as initial material size, pyrolysis temperature and hold time on the properties of pyrolized chars. To determine the optimum conditions for producing activated carbon, the effect of activation temperature and activation time have been studied. The maximum BET surface area of 613.43 m2/g and highest methylene blue adsorption capacity of 8.27 mg/g was obtained at a pyrolysis temperature of 600°C for hold time 1.5 hr followed by steam activation at a temperature of 800°C for a hold time of 1 hr. The produced activated carbon was almost like ash at 900°C. FT-IR and TG/DTA have been done in order to understand the structural changes during the process. The waste material was a suitable raw material for the production of good quality activated carbon. DOI: http://dx.doi.org/10.3329/bjsir.v47i3.13056 Bangladesh J. Sci. Ind. Res. 47(3), 257-264, 2012

Synthesis and evaluation of activated carbon/nanoclay/ thiolated graphene oxide nanocomposite for lead(II) removal from aqueous solution

2019 ◽  
Vol 79 (3) ◽  
pp. 466-479 ◽  
Author(s):  
Fatemeh Mojoudi ◽  
Amir Hossein Hamidian ◽  
Yu Zhang ◽  
Min Yang
Keyword(s):  
Graphene Oxide ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Isotherm Model ◽  
Bet Surface Area ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Adsorption ◽  
Fast Kinetics

Abstract Novel porous nanocomposite (AC/NC/TGO) was successfully synthesized through the composition of activated carbon, nanoclay and graphene oxide as a Pb(II) adsorbent for the treatment of contaminated aqueous environment. The physicochemical properties and morphology of AC/NC/TGO were examined by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and nitrogen adsorption-desorption techniques. Results showed Pb(II) adsorption on the AC/NC/TGO was rapid in the first 20 min and reached equilibrium in 40 min. Kinetic studies showed significant fit to the pseudo second order kinetic model (R2 ≥ 0.9965) giving an equilibrium rate constant (K2) of 0.0017 g mg−1 min−1 for Pb(II) loaded. The experimental adsorption data were better fitted with the Langmuir isotherm model than with the Freundlich isotherm model. Prepared nanocomposite exhibited high values of Brunauer–Emmett–Teller (BET) surface area of 1,296 m2 g−1 and total pore volume of 1.01 cm3 g−1. Maximum adsorption capacity (Qmax = 208 mg g−1) and a relatively high adsorption rate was achieved at pH 5.0 using an adsorbent dose of 0.5 g L−1 and an initial lead concentration of 50 mg L−1. High adsorption capacity, reusability, fast kinetics and simple synthesis method indicate that prepared nanocomposite can be suggested as a high-performance adsorbent for Pb(II) removal from polluted water.

Synthesis and Characterization of Carbon/Bentonite Composite

2012 ◽  
Vol 549 ◽  
pp. 703-706
Author(s):  
De Yi Zhang ◽  
Jing Wu ◽  
Bai Yi Chen ◽  
He Ming Luo ◽  
Kun Jie Wang ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Activated Carbon ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Heavy Metal Ions ◽  
Low Cost ◽  
Raw Material ◽  
Hydroxyl Groups ◽  
Carbon Particles ◽  
Prepared Composite

In this paper, a novel carbon/bentonite composite was prepared using sucrose as carbon source and bentonite as raw material. The characterization results shown that plenty of carbon particles distribute on the surface of the composite, and an abundant of functional groups, such as SO3H, carboxylic and hydroxyl groups, were successfully introduced onto the surface of the prepared composite. The adsorption capacity of the prepared composite for typical heavy metal ions and methylene blue deys also was investigated and compared with activated carbon and bentonite, the results show that the composite shows excellent adsorprion performance for heavy metal ions, and the adsorption capacity for Cu2+and Ni2+ increase by 136% and 591% than natural bentonite, respectSuperscript textively. The prepared composite with excellent adsorption performance could be used as a low-cost alternative to activated carbon for the treatment of heavy metal ions polluted wastewater.

Cd(II) removal on surface-modified activated carbon: equilibrium, kinetics and mechanism

2016 ◽  
Vol 74 (8) ◽  
pp. 1800-1808 ◽  
Author(s):  
Jianjun Liang ◽  
Meiling Liu ◽  
Yufei Zhang
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Orthogonal Experiment ◽  
Xrd Analysis ◽  
Bet Surface Area ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Modified Activated Carbon ◽  
Surface Modified

Commercial pulverous activated carbon (AC-0) was modified through two steps: oxidize AC-0 acid firstly, impregnate it with iron using ferric chloride secondly. Orthogonal experiment was conducted then to prepare modified activated carbon with high Cd(II) adsorption capacity (ACNF). Batch adsorption experiments were undertaken to determine the adsorption characteristics of Cd(II) from aqueous solution onto AC-0 and ACNF and the effect of pH, contact time and initial Cd(II) concentration. The results indicate that: the adsorption behavior of Cd(II) on ACNF can be well fitted with Langmuir model, and the maximum adsorption capacity of ACNF was 2.3 times higher than that of AC-0, supporting a monolayer coverage of Cd(II) on the surface. The kinetics of the adsorption process can be described by pseudo-second-order rate equation very well, and the adsorption capacity increased from 0.810 mg/g to 0.960 mg/g after modification. Compared with AC-0, the kinetic parameters of ACNF showed a higher adsorption rate through the aqueous solution to the solid surface and a lower intraparticle diffusion rate. Surface modification resulted in a lower Brunauer–Emmett–Teller (BET) surface area and pore size because of the collapse and blockage of pores, according to the X-ray diffraction (XRD) analysis, while the total number of surface oxygen acid groups increased, and this was supposed to contribute to the enhanced adsorption capacity of modified activated carbon.

Sign in / Sign up

Export Citation Format

Share Document