scholarly journals Optimization of fatigue strength of selective inhibition sintered polyamide 12 parts using RSM

2020 ◽  
Vol 7 ◽  
pp. 23
Author(s):  
Mesfin Sisay ◽  
Esakki Balasubramanian
Keyword(s):  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Selective Inhibition ◽  
Layer By Layer ◽  
Process Variables ◽  
Polyamide 12 ◽  
Selective Inhibition Sintering ◽  
Nylon 12 ◽  
Rate Optimization ◽  
Feed Rate Optimization

Selective inhibition sintering (SIS) is a powder based that fabricate functional parts through fusion of powder bed on a layer by layer basis. Being a new fabrication method, the correlation between process variables and part properties are not fully comprehended. Polyamide 12 (nylon 12) is one of the widely used materials in powder based AM processes including SIS. Therefore, in this work, the effect of critical SIS process parameters on the fatigue behavior of polyamide 12 parts was experimentally investigated, and the parameter settings were optimized to maximize fatigue strength. The number of experimental runs was determined based on Box-Behnken design, and specimens were fabricated as per ASTM D7791. Specimens were tested by subjected them to fluctuating loading at a frequency of 3 Hz. The test results were analyzed using Minitab statistical analysis software. From the ANOVA result, it was identified that the fatigue life of SIS parts is significantly influenced by layer thickness, heater temperature, and heater feed rate. Optimization of process variables settings was performed using the Minitab response optimizer and maximum fatigue strength of 17.43 MPa was obtained. The verification experiment resulted in 17.93 MPa fatigue strength which is comparable to the predicted value and with the result from the literatures.

scholarly journals Effect of Various Infrared Heaters on Sintering Behavior of UHMWPE in Selective Inhibition Sintering Process

2019 ◽  
Vol 8 (6) ◽  
pp. 725-731 ◽  
Keyword(s):  
Surface Roughness ◽  
Computer Aided Design ◽  
Low Cost ◽  
Laser System ◽  
Selective Laser Sintering ◽  
Heating Surface ◽  
Selective Inhibition ◽  
Sintering Behavior ◽  
Layer By Layer ◽  
Selective Inhibition Sintering

Selective inhibition sintering (SIS) is an emerging powder-based additive manufacturing technology that creates polymer or metal based parts through adhesion of layer-by-layer from three-dimensional computer-aided design model. Replacement of costly laser system in selective laser sintering tremendously reduces the cost of manufacturing. SIS attempts to incorporate low cost heaters to achieve efficient sintering for production of high quality parts. However, SIS demands uniform heating of each layer for effective sintering. The present study focused on examining the heating characteristics of three different types of infrared heaters with respect to various layer thickness and determining the optimal distance between the heating surface and the powder bed. Experiments are conducted using the low-cost heaters to obtain uniform distribution of heat energy across the ultra-high molecular weight polyethylene (UHMWPE) powder surface. The thermal and optical images are captured to observe the temperature distribution on the powder and the surface roughness. Tensile and compressive specimens were fabricated and their corresponding strength was determined and surface roughness was measured to study the surface characteristics of the parts.

scholarly journals Fatigue Modeling and Numerical Analysis of Re-Filling Probe Hole of Friction Stir Spot Welded Joints in Aluminum Alloys

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2171
Author(s):  
Armin Yousefi ◽  
Ahmad Serjouei ◽  
Reza Hedayati ◽  
Mahdi Bodaghi
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Element Model ◽  
Plastic Strain Amplitude ◽  
Friction Stir ◽  
Probe Hole ◽  
Good Agreement

In the present study, the fatigue behavior and tensile strength of A6061-T4 aluminum alloy, joined by friction stir spot welding (FSSW), are numerically investigated. The 3D finite element model (FEM) is used to analyze the FSSW joint by means of Abaqus software. The tensile strength is determined for FSSW joints with both a probe hole and a refilled probe hole. In order to calculate the fatigue life of FSSW joints, the hysteresis loop is first determined, and then the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted. The results were verified against available experimental data from other literature, and a good agreement was observed between the FEM results and experimental data. The results showed that the joint’s tensile strength without a probe hole (refilled hole) is higher than the joint with a probe hole. Therefore, re-filling the probe hole is an effective method for structures jointed by FSSW subjected to a static load. The fatigue strength of the joint with a re-filled probe hole was nearly the same as the structure with a probe hole at low applied loads. Additionally, at a high applied load, the fatigue strength of joints with a refilled probe hole was slightly lower than the joint with a probe hole.

Evaluation of Parts Produced by a Novel Additive Manufacturing Process

2013 ◽  
Vol 315 ◽  
pp. 63-67 ◽  
Author(s):  
Muhammad Fahad ◽  
Neil Hopkinson
Keyword(s):  
Additive Manufacturing ◽  
Rapid Prototyping ◽  
Manufacturing Process ◽  
High Speed ◽  
Three Dimensional ◽  
Coordinate Measuring Machine ◽  
Layer By Layer ◽  
Nylon 12 ◽  
Measuring Machine ◽  
End Use

Rapid prototyping refers to building three dimensional parts in a tool-less, layer by layer manner using the CAD geometry of the part. Additive Manufacturing (AM) is the name given to the application of rapid prototyping technologies to produce functional, end use items. Since AM is relatively new area of manufacturing processes, various processes are being developed and analyzed for their performance (mainly speed and accuracy). This paper deals with the design of a new benchmark part to analyze the flatness of parts produced on High Speed Sintering (HSS) which is a novel Additive Manufacturing process and is currently being developed at Loughborough University. The designed benchmark part comprised of various features such as cubes, holes, cylinders, spheres and cones on a flat base and the build material used for these parts was nylon 12 powder. Flatness and curvature of the base of these parts were measured using a coordinate measuring machine (CMM) and the results are discussed in relation to the operating parameters of the process.The result show changes in the flatness of part with the depth of part in the bed which is attributed to the thermal gradient within the build envelope during build.

A Novel Algorithm for Time Optimal Trajectory Planning

2014 ◽  
Author(s):  
Mingxing Yuan ◽  
Bin Yao ◽  
Dedong Gao ◽  
Xiaocong Zhu ◽  
Qingfeng Wang
Keyword(s):  
Trajectory Planning ◽  
Optimal Trajectory ◽  
Optimal Solution ◽  
Problem Of Time ◽  
High Productivity ◽  
Hard Constraints ◽  
Time Optimal ◽  
Rate Optimization ◽  
Feed Rate Optimization ◽  
Optimal Trajectory Planning

Time optimal trajectory planning under various hard constraints plays a significant role in simultaneously meeting the requirements on high productivity and high accuracy in the fields of both machining tools and robotics. In this paper, the problem of time optimal trajectory planning is first formulated. A novel back and forward check algorithm is subsequently proposed to solve the minimum time feed-rate optimization problem. The basic idea of the algorithm is to search the feasible solution in the specified interval using the back or forward operations. Four lemmas are presented to illustrate the calculating procedure of optimal solution and the feasibility of the proposed algorithm. Both the elliptic curve and eight profile are used as case studies to verify the effectiveness of the proposed algorithm.

High Cycle Fatigue Behavior of Thermally Oxidized Ti6Al4V Alloy

2007 ◽  
Vol 561-565 ◽  
pp. 2179-2182 ◽  
Author(s):  
Mehmet Cingi ◽  
Onur Meydanoglu ◽  
Hasan Guleryuz ◽  
Murat Baydogan ◽  
Huseyin Cimenoglu ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Yield Strength ◽  
Thermal Oxidation ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Ti6al4v Alloy ◽  
Bending Fatigue ◽  
Rotating Bending Fatigue ◽  
Rotating Bending ◽  
Bending Fatigue Strength

In this study, the effect of thermal oxidation on the high cycle rotating bending fatigue behavior of Ti6Al4V alloy was investigated. Oxidation, which was performed at 600°C for 60 h in air, considerably improved the surface hardness and particularly the yield strength of the alloy without scarifying the tensile ductility. Unfortunately, the rotating bending fatigue strength at 5x106 cycles decreased from about 610 MPa to about 400 MPa upon oxidation. Thus, thermal oxidation leaded a reduction in the fatigue strength of around 34%, while improving the surface hardness (HV0.1) and yield strength 85 % and 36 %, respectively.

scholarly journals Fatigue Behavior of Non-Optimized Laser-Cut Medical Grade Ti-6Al-4V-ELI Sheets and the Effects of Mechanical Post-Processing

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 843 ◽  
Author(s):  
André Reck ◽  
André Till Zeuner ◽  
Martina Zimmermann
Keyword(s):  
Surface Roughness ◽  
Fatigue Strength ◽  
Surface Quality ◽  
Laser Cutting ◽  
Fatigue Behavior ◽  
Fatigue Cracks ◽  
Surface Condition ◽  
Mechanical Polishing ◽  
Fatigue Properties ◽  
Post Processing

The study presented investigates the fatigue strength of the (α+β) Ti-6Al-4V-ELI titanium alloy processed by laser cutting with and without mechanical post-processing. The surface quality and possible notch effects as a consequence of non-optimized intermediate cutting parameters are characterized and evaluated. The microstructural changes in the heat-affected zone (HAZ) are documented in detail and compared to samples with a mechanically post-processed (barrel grinding, mechanical polishing) surface condition. The obtained results show a significant increase (≈50%) in fatigue strength due to mechanical post-processing correlating with decreased surface roughness and minimized notch effects when compared to the surface quality of the non-optimized laser cutting. The martensitic α’-phase is detected in the HAZ with the formation of distinctive zones compared to the initial equiaxial α+β microstructure. The HAZ could be removed up to 50% by means of barrel grinding and up to 100% through mechanical polishing. A fracture analysis revealed that the fatigue cracks always initiate on the laser-cut edges in the as-cut surface condition, which could be assigned to an irregular macro and micro-notch relief. However, the typical characteristics of the non-optimized laser cutting process (melting drops and significant higher surface roughness) lead to early fatigue failure. The fatigue cracks solely started from the micro-notches of the surface relief and not from the dross. As a consequence, the fatigue properties are dominated by these notches, which lead to significant scatter, as well as decreased fatigue strength compared to the surface conditions with mechanical finishing and better surface quality. With optimized laser-cutting conditions, HAZ will be minimized, and surface roughness strongly decreased, which will lead to significantly improved fatigue strength.

scholarly journals Fatigue Performance of Thin Laser Butt Welds in HSLA Steel

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1499
Author(s):  
Patricio G. Riofrío ◽  
Fernando Antunes ◽  
José Ferreira ◽  
António Castanhola Batista ◽  
Carlos Capela
Keyword(s):  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Hsla Steel ◽  
High Strength ◽  
Butt Joints ◽  
Factors Affecting ◽  
Weld Profile ◽  
The Relationship ◽  
Good Agreement ◽  
Significant Factors

This work is focused on understanding the significant factors affecting the fatigue strength of laser-welded butt joints in thin high-strength low-alloy (HSLA) steel. The effects of the weld profile, imperfections, hardness, and residual stresses were considered to explain the results found in the S-N curves of four welded series. The results showed acceptable fatigue strength although the welded series presented multiple-imperfections. The analysis of fatigue behavior at low stress levels through the stress-concentrating effect explained the influence of each factor on the S-N curves of the welded series. The fatigue limits of the welded series predicted through the stress-concentrating effect and by the relationship proposed by Murakami showed good agreement with the experimental results.

Influence of Manufacturing Process on the Fatigue Strength of Gears

2014 ◽  
Vol 1018 ◽  
pp. 269-276
Author(s):  
Andrea Reiß ◽  
Ulf Engel
Keyword(s):  
Fatigue Strength ◽  
Surface Quality ◽  
Fatigue Behavior ◽  
High Surface ◽  
Research Work ◽  
Dimensional Accuracy ◽  
Cold Forging ◽  
Hardness Distribution ◽  
Forming Process ◽  
High Surface Quality

With cold forging processes it is possible to produce parts characterized by high strength, high dimensional accuracy and high surface quality. In order to optimize the forming process and to be able to use the advantages of cold forging specifically and combined, it is necessary to find correlations between manufacturing parameters on the one side, strength and other properties like hardness distribution and surface quality of the component on the other side. The research work covered in this paper focuses on the correlation of the components properties influenced by its manufacturing history and their fatigue strength. The used component is a gear produced by a lateral cold forging process. For the investigations an experimental setup has been designed. The aim for the design of the setup is to reproduce the real contact condition for the contact of two gears. To obtain different component properties the production process of the gear was varied by producing the parts by a milling operation. First of all, the components’ properties, for example hardness distribution, remaining residual stresses, orientation of fibers and surface quality, were determined. The components’ fatigue behavior was determined using a high frequency pulsator and evaluated in terms of finite life fatigue strength and fatigue endurance limit. These examinations were used to produce Woehler curves for the differently manufactured components with a certain statistical data analysis method.

Sign in / Sign up

Export Citation Format

Share Document