scholarly journals Composite Materials with Epoxy Matrix and Their Properties

2021 ◽  
Vol 1199 (1) ◽  
pp. 012030
Author(s):  
P Skalková ◽  
V Krmelová ◽  
J Krmela ◽  
D Ondrušová ◽  
A Crkoň
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Weight Loss ◽  
Tensile Strength ◽  
Composite Materials ◽  
Reinforced Composites ◽  
Lower Content ◽  
Flexural Stress ◽  
Number Of Layers ◽  
Ep Matrix

Abstract This work was focused on studying the properties of epoxy (EP) composite materials reinforced with glass, (GF) carbon (CF) and aramid (AF) fibres. The composites were made by hand lay-up (HL) and vacuum infusion process (VIP) with 8, 10, 12 number of fabric layers. Studied were tensile strength, elongation, flexural stress, flexural strain, thermal stability, texture of surfaces, cuts, fractures of laminates and the thickness of the laminate according to the type and number of layers of fabric and the method of manufacture. Composites made by VIP achieve better mechanical properties than composites made by HL. Tensile strength was highest in composites reinforced with AF. Composite materials reinforced with GF exhibit the lowest values of tensile strength. Flexural strength was significantly the highest in CF reinforced composites followed by the laminates reinforced with GF and AF. The highest values of flexural deformation were measured in composites reinforced with AF and the lowest values of flexural deformation were measured in composites reinforced with CF. By thermogravimetric analysis (TGA) was recorded weight loss of the EP matrix in the range from 290 to 480 °C and AF in range from 530 to 605 °C. By TGA was demonstrated lower content of EP matrix in the composites made by VIP, which was confirmed by comparison of thickness of the studied laminates.

scholarly journals Performance Evaluation of Cellulose Nanofiber with Residual Hemicellulose as a Nanofiller in Polypropylene-Based Nanocomposite

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1064
Author(s):  
Mohd Nor Faiz Norrrahim ◽  
Hidayah Ariffin ◽  
Tengku Arisyah Tengku Yasim-Anuar ◽  
Mohd Ali Hassan ◽  
Nor Azowa Ibrahim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Weight Loss ◽  
Tensile Strength ◽  
Performance Evaluation ◽  
Flexural Strength ◽  
Decomposition Temperature ◽  
Cellulose Nanofiber ◽  
Hemicellulose Removal ◽  
Reinforcement Material

Residual hemicellulose could enhance cellulose nanofiber (CNF) processing as it impedes the agglomeration of the nanocellulose fibrils and contributes to complete nanofibrillation within a shorter period of time. Its effect on CNF performance as a reinforcement material is unclear, and hence this study seeks to evaluate the performance of CNF in the presence of amorphous hemicellulose as a reinforcement material in a polypropylene (PP) nanocomposite. Two types of CNF were prepared: SHS-CNF, which contained about 11% hemicellulose, and KOH-CNF, with complete hemicellulose removal. Mechanical properties of the PP/SHS-CNF and PP/KOH-CNF showed an almost similar increment in tensile strength (31% and 32%) and flexural strength (28% and 29%) when 3 wt.% of CNF was incorporated in PP, indicating that hemicellulose in SHS-CNF did not affect the mechanical properties of the PP nanocomposite. The crystallinity of both PP/SHS-CNF and PP/KOH-CNF nanocomposites showed an almost similar value at 55–56%. A slight decrement in thermal stability was seen, whereby the decomposition temperature at 10% weight loss (Td10%) of PP/SHS-CNF was 6 °C lower at 381 °C compared to 387 °C for PP/KOH-CNF, which can be explained by the degradation of thermally unstable hemicellulose. The results from this study showed that the presence of some portion of hemicellulose in CNF did not affect the CNF properties, suggesting that complete hemicellulose removal may not be necessary for the preparation of CNF to be used as a reinforcement material in nanocomposites. This will lead to less harsh pretreatment for CNF preparation and, hence, a more sustainable nanocomposite can be produced.

scholarly journals JUSTIFICATION OF USING MULTILAYER COMPOSITE MATERIALS IN SHIPBUILDING

2019 ◽  
pp. 37-47
Author(s):  
Alsaid Mazen ◽  
Ali Salamekh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Polymer Composite ◽  
Testing Machine ◽  
Steel Structures ◽  
Polymer Composite Materials ◽  
Number Of Layers ◽  
Study Results ◽  
Glass Mat

The development of modern shipbuilding requires using new structural materials, superior to traditional ones. Polymeric composite materials are among the most promising. The article studies the mechanical properties of multilayer polymer composite materials made of glass fabrics under tension and the effect of the number of layers of glass mat on the tensile strength of the material. The technology of manufacturing samples from polymer composites reinforced with fiberglass plastic is being considered. The size and shape of the samples, the technological parameters of the manufacturing process, which depend on standard requirements, and the technological features of the testing machine are substantiated. It has been stated that fiberglass is the cheapest and most common type of composite materials, which does not require special maintenance, the cost of maintenance of fiberglass structures being significantly lower than that of steel structures. The method of testing the tensile strength of the samples has been studied. For conducting experiments, samples of glass mat brand EMC-600-1250-E were used. According to the study results, the mathematical dependence of tensile strength on the number of layers was established, and the most important stages of statistical processing of test results were laid out using the Minitab 18.1 software package. A graph of the relationship between the number of layers and tensile strength is presented. For all the examined samples the ultimate strength will depend on the number of layers. The results of mechanical properties can be used in solving problems associated with the application of polymer composite materials in shipbuilding, for example, in manufacturing superstructures of dry cargo vessels.

scholarly journals Roadmap of Effects of Biowaste-Synthesized Carbon Nanomaterials on Carbon Nano-Reinforced Composites

Catalysts ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1485
Author(s):  
Bhavana H. Thippeswamy ◽  
Anantha Sunil Maligi ◽  
Gurumurthy Hegde
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Polymer Nanocomposites ◽  
Carbon Nanomaterials ◽  
Sustainable Growth ◽  
Natural Ecosystem ◽  
Reinforced Composites ◽  
Pyrolysis Process ◽  
Thermosetting Polymers

Sustainable growth can be achieved by recycling waste material into useful resources without affecting the natural ecosystem. Among all nanomaterials, carbon nanomaterials from biowaste are used for various applications. The pyrolysis process is one of the eco-friendly ways for synthesizing such carbon nanomaterials. Recently, polymer nanocomposites (PNCs) filled with biowaste-based carbon nanomaterials attracted a lot of attention due to their enhanced mechanical properties. A variety of polymers, such as thermoplastics, thermosetting polymers, elastomers, and their blends, can be used in the formation of composite materials. This review summarizes the synthesis of carbon nanomaterials, polymer nanocomposites, and mechanical properties of PNCs. The review also focuses on various biowaste-based precursors, their nanoproperties, and turning them into proper composites. PNCs show improved mechanical properties by varying the loading percentages of carbon nanomaterials, which are vital for many defence- and aerospace-related industries. Different synthesis processes are used to achieve enhanced ultimate tensile strength and modulus. The present review summarizes the last 5 years’ work in detail on these PNCs and their applications.

scholarly journals High modulus polyimide particle-reinforcement of epoxy composites

2021 ◽  
Author(s):  
Johannes Essmeister ◽  
M. Josef Taublaender ◽  
Thomas Koch ◽  
D. Alonso Cerrón-Infantes ◽  
Miriam M. Unterlass ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Composite Materials ◽  
Epoxy Matrix ◽  
Epoxy Composites ◽  
High Modulus ◽  
Particle Reinforcement

A novel class of fully organic composite materials with well-balanced mechanical properties and improved thermal stability was developed by incorporating highly crystalline, hydrothermally synthesized polyimide microparticles into an epoxy matrix.

scholarly journals Effects of Substitution of Y with Yb and Ce on the Microstructures and Mechanical Properties of Mg88.5Zn5Y6.5

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 31
Author(s):  
Hongxin Liao ◽  
Taekyung Lee ◽  
Jiangfeng Song ◽  
Jonghyun Kim ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Creep Resistance ◽  
Room Temperature ◽  
High Thermal Stability ◽  
Long Period ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of the Mg88.5Zn5Y6.5-XREX (RE = Yb and Ce, X = 0, 1.5, 3.0, and 4.5) (wt.%) alloys were investigated in the present study. Mg88.5Zn5Y6.5 is composed of three phases, namely, α-Mg, long-period stacking ordered (LPSO) phases, and intermetallic compounds. The content of the LPSO phases decreased with the addition of Ce and Yb, and no LPSO phases were detected in Mg88.5Zn5Y2.0Yb4.5. The alloys containing the LPSO phases possessed a stratified microstructure and exhibited excellent mechanical properties. Mg88.5Zn5Y5.0Ce1.5 exhibited the highest creep resistance and mechanical strength at both room temperature and 200 °C, owing to its suitable microstructure and high thermal stability. The yield strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature was 358 MPa. The ultimate tensile strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature and 200 °C was 453 MPa and 360 MPa, respectively.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

Preparation and characterizations of ternary biodegradable blends composed of polylactide, poly(ε-caprolactone), and wood flour

2012 ◽  
Vol 32 (6-7) ◽  
pp. 435-444 ◽  
Author(s):  
Hsin-Tzu Liao ◽  
Chin-San Wu
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Tensile Strength ◽  
Fourier Transform ◽  
Wood Flour ◽  
High Price ◽  
Infrared Analysis ◽  
Melt Blending ◽  
Ternary Blends ◽  
Elongation At Break

Abstract Melt blending of polylactide (PLA), poly(ε-caprolactone) (PCL), and wood flour (WF) was performed in an effort to overcome the major drawbacks (brittleness and high price) of PLA. In addition, the acrylic acid (AA)-grafted PLA70PCL30 (PLA70PCL30-g-AA) was used as the alternative for the preparation of ternary blends to improve the compatibility and the dispersability of WF within the PLA70PCL30 matrix. As expected, PCL improved the elongation at break and the toughness of PLA but decreased the tensile strength and modulus. Because the hydrophilic WF is dispersed physically in the hydrophobic PLA70PCL30 matrix, as the result of Fourier transform infrared analysis, the mechanical properties of PLA70PCL30 became noticeably worse when it was blended with WF. This problem was successfully conquered by using PLA70PCL30-g-AA to replace PLA70PCL30 due to the formation of an ester carbonyl group between PLA70PCL30-g-AA and WF. Furthermore, the PLA70PCL30-g-AA/WF blend provided a plateau tensile strength at break when the WF content was up to 50 wt%. PLA70PCL30/WF exhibited a tensile strength at break of approximately 3–25 MPa more than PLA70PCL30-g-AA/WF. By using p-cresol and tyrosinase, the enzymatic biodegradable test showed that PLA70PCL30-g-AA is somewhat more biodegradable than PLA70PCL30 because the former has better water absorption. After 16 weeks, the weight loss of the PLA70PCL30/WF (50 wt%) composite was >80%. PLA70PCL30-g-AA/WF exhibited a weight loss of approximately 1–12 wt% more than PLA70PCL30-g-AA/WF. It was also found that the addition of WF to PLA70PCL30 or PLA70PCL30-g-AA decreased the crystallinity of PLA and PCL in PLA70PCL30 or PLA70PCL30-g-AA and then increased their biodegradable property.

Co-milling-assisted exfoliated graphite nanoplatelets filler introduction in polyethylene and alumina composites

2018 ◽  
Vol 53 (13) ◽  
pp. 1815-1826
Author(s):  
Sheng Cai Tan ◽  
Jimmy KW Chan ◽  
Kian Ping Loh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Exfoliated Graphite ◽  
Flexural Properties ◽  
Graphite Nanoplatelets ◽  
Alumina Composites ◽  
Exfoliated Graphite Nanoplatelets ◽  
Polyethylene Composites

This paper aims to investigate the effect of co-milling-assisted exfoliation of graphite into polyethylene and alumina matrices on the mechanical properties of the composites. Tensile mechanical properties of composite materials based on polyethylene reinforced with graphite and graphite-derived fillers at 0–0.75 wt% loading were investigated, while hardness and flexural properties of alumina composites with 0.25 wt% loading of the same additives were assessed. Exfoliated graphite, applied at 0.25–0.75 wt% in pre-exfoliated form or in a co-milling-assisted fashion, has been demonstrated to be effective in enhancing the tensile strength of polyethylene composites. Similar enhancement in hardness and flexural properties was observed in alumina composites with 0.25 wt% loading of the exfoliated graphite. Co-milling-assisted exfoliated graphite nanoplatelets additive introduction has been found to effect a more desirable mechanical properties enhancement in the composites investigated in this study.

scholarly journals Tension mechanical properties of recycled glass-epoxy composite material

2012 ◽  
pp. 189-198 ◽  
Author(s):  
Jelena Petrovic ◽  
Darko Ljubic ◽  
Marina Stamenovic ◽  
Ivana Dimic ◽  
Slavisa Putic
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Composite Materials ◽  
Modulus Of Elasticity ◽  
Epoxy Composite ◽  
Raw Materials ◽  
Mechanical Tests ◽  
Recycled Glass ◽  
Before And After

The significance of composite materials and their applications are mainly due to their good properties. This imposes the need for their recycling, thus extending their lifetime. Once used composite material will be disposed as a waste at the end of it service life. After recycling, this kind of waste can be used as raw materials for the production of same material, which raises their applicability. This indicates a great importance of recycling as a method of the renowal of composite materials. This study represents a contribution to the field of mechanical properties of the recycled composite materials. The tension mechanical properties (tensile strength and modulus of elasticity) of once used and disposed glass-epoxy composite material were compared before and after the recycling. The obtained results from mechanical tests confirmed that the applied recycling method was suitable for glass-epoxy composite materials. In respect to the tensile strength and modulus of elasticity it can be further assessed the possibility of use of recycled glass-epoxy composite materials.

scholarly journals ANALISIS KEKUATAN TARIK DAN IMPAK MATERIAL KOMPOSIT POLIMER DALAM APLIKASI FIBERBOAT

2021 ◽  
Vol 4 ◽  
pp. 121-126
Author(s):  
Rezza Ruzuqi ◽  
Victor Danny Waas
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Materials ◽  
Impact Strength ◽  
Metal Corrosion ◽  
Phase System ◽  
Low Density ◽  
Weight Percentage ◽  
Multi Phase ◽  
The Impact

Composite material is a material that has a multi-phase system composed of reinforcing materials and matrix materials. Causes the composite materials to have advantages in various ways such as low density, high mechanical properties, performance comparable to metal, corrosion resistance, and easy to fabricate. In the marine and fisheries industry, composite materials made from fiber reinforcement, especially fiberglass, have proven to be very special and popular in boat construction because they have the advantage of being chemically inert (both applied in general and marine environments), light, strong, easy to print, and price competitiveness. Thus in this study, tensile and impact methods were used to determine the mechanical properties of fiberglass polymer composite materials. Each test is carried out on variations in the amount of fiberglass laminate CSM 300, CSM 450 and WR 600 and variations in weight percentage 99.5% -0.5%, 99% -1%, 98.5% -1, 5%, 98% -2% and 97.5%-2.5% have been used. The results showed that the greater the number of laminates, the greater the impact strength, which was 413,712 MPa, and the more the percentage of hardener, the greater the impact strength, which was 416,487 MPa. The results showed that the more laminate the tensile strength increased, which was 87.054 MPa, and the more the percentage of hardener, the lower the tensile strength, which was 73.921 MPa.

Sign in / Sign up

Export Citation Format

Share Document