scholarly journals Silicate conductive composites with graphite-based fillers

2021 ◽  
Vol 1209 (1) ◽  
pp. 012035
Author(s):  
Š Baránek ◽  
V Černý ◽  
G Yakovlev ◽  
R Drochytka
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Construction Industry ◽  
Machine Building ◽  
Building Industry ◽  
Electrically Conductive ◽  
Conductive Composites ◽  
Flexural Tensile Strength ◽  
Overvoltage Protection

Abstract Electroconductive composites are modern materials that are commonly used in many industries such as construction industry and machine-building industry. For example, these materials can be useful as sensors for monitoring changes in constructions, shielding stray currents from electrification networks, shielding electromagnetic radiation in operating rooms, cathodic protection against moisture or overvoltage protection of buildings. The topic of this post is the research of electrically conductive silicate composites with graphite-based fillers. In this research will be tested composites with different ratio and types of graphite and monitor their electroconductive properties like impedance, and physical-mechanical properties like compressive and tensile strength. The post describes basic properties and interactions of silicate electrically conductive composites with graphite fillers. It was found that by adding 10 % wt. graphite into silicate composites, impedance is reduced by 50% and compressive strength by 40%. The flexural tensile strength depends mainly on the roughness of the particles, where the coarser flaky particles transfer the load better and increase the strength while very fine graphites reduce the flexural tensile strength. Furthermore, it has been found that very finely ground synthetic graphites are most suitable for achieving low impedance of composites.

Experiment and Research on Mechanic Behavior of Concrete with Different Addition Amounts of Polypropylene Fibers

2012 ◽  
Vol 430-432 ◽  
pp. 1064-1067
Author(s):  
Yu Zhi Chen ◽  
Wei Hong Xuan ◽  
Xiao Hong Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Polypropylene Fiber ◽  
Polypropylene Fibers ◽  
Flexural Tensile Strength ◽  
Axial Compressive Strength ◽  
Low Dosage

The effect of the different addition amounts of polypropylene fibers on the basic mechanical properties of concrete were investigated in this paper. The results show that the flexural tensile strength of concrete changed slightly after adding low-dosage polypropylene fiber(0.04%～0.16%); Axial compressive strength and flexural tension modulus decreased, limiting flexural strain increased gradually with the amounts of fibers rising.

scholarly journals Influence of Addition Contents of Iron Ore Tailings on Structural Mortar

2021 ◽  
Vol 11 (1) ◽  
pp. 74
Author(s):  
Nara Linhares Borges de Castro ◽  
Bruna Silva Almada ◽  
Abner Araújo Fajardo ◽  
Carlos Augusto Oliveira ◽  
White José dos Santos
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Physical Properties ◽  
Open Porosity ◽  
Iron Ore ◽  
Cementitious Composites ◽  
Carbonation Depth ◽  
Flexural Tensile Strength ◽  
Iron Ore Tailings

This study discusses and analyzes an alternative of IOT reuse as addition in structural mortars, evaluating the influence of IOT addition contents. The material was physically and chemically characterized. Structural mortars were molded with 10%, 20%, 30% and 40% of addition of IOT in relation to cement mass. We investigate physical properties, mechanical indicators, durability indicators and microstructure. The tailings are composed of predominantly quartz, hematite and goethite, and no components were found that could compromise the cementitious composites. The addition of IOT provided a tendency to reduce open porosity. The addition of 30% IOT was the most efficient in closing pores. All addition contents led to the maintenance or gains in mechanical properties, and a 10% gain in flexural tensile strength was observed for the addition of 10% IOT. The addition of 40% IOT promoted a 14% gain in compressive strength and maintenance of flexural tensile strength. This addition content evidences that the carbonation depth was not significantly affected. Based on the results, the addition percentages of 30-40% are interesting as to the analyzed properties.

scholarly journals The Effects of Maximum Attapulgite Aggregate Size and Steel Fibers Content on Fresh and Some Mechanical Properties of Lightweight Self Compacting Concrete

2020 ◽  
Vol 26 (5) ◽  
pp. 172-190
Author(s):  
Shubbar Jawad Al-obaidey
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Aggregate Size ◽  
Steel Fibers ◽  
Maximum Aggregate Size ◽  
Marginal Effect ◽  
Fresh Properties ◽  
Self Compacting Concrete ◽  
Flexural Tensile Strength

The main objectives of this study were investigating the effects of the maximum size of coarse Attapulgite aggregate and micro steel fiber content on fresh and some mechanical properties of steel fibers reinforced lightweight self-compacting concrete (SFLWSCC). Two series of mixes were used depending on maximum aggregate size (12.5 and 19) mm, for each series three different steel fibers content were used (0.5 %, 1%, and 1.5%). To evaluate the fresh properties, tests of slump flow, T500 mm, V funnel time, and J ring were carried out. Tests of compressive strength, splitting tensile strength, flexural tensile strength, and calculated equilibrium density were done to evaluate mechanical properties. For reference mixes, the results showed that mixes with a larger maximum aggregate size of 19 mm exhibited better fresh properties, while mechanical properties negatively affected by using a larger maximum aggregate size. The results also showed that using steel fibers led to negative effects on fresh properties, especially with higher steel fibers content and larger maximum aggregate size. The marginal effect of steel fibers on compressive strength was noticed, while for both splitting and flexural tensile strength, significant increase was obtained with increasing of steel fibers content. The properties of SFLWSCC in the fresh state had a considerable effect on mechanical properties, whereas with the best fresh properties, the best mechanical properties can be obtained.

Experiment of Basic Mechanical Properties of Concrete Mixed with Composite Coarse-Aggregate

2010 ◽  
Vol 168-170 ◽  
pp. 2178-2181 ◽  
Author(s):  
Feng Lan Li ◽  
Jing Li ◽  
Song Chen ◽  
Wen Jie Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Cement Content ◽  
Lightweight Aggregate ◽  
Flexural Tensile Strength ◽  
Axial Compressive Strength ◽  
Crushed Limestone

The mechanical properties of concrete mixed with composite coarse-aggregate were studied by the orthogonal test method, in which the four factors such as the cement content, the percent of cement replaced by fly ash, the percent of crushed limestone with grain size of 16-25 mm replaced by lightweight aggregate with the same grain size and the water to binder (cement + fly ash) ratio were considered. The results show that the water to binder ratio is the most effective factor influencing all of the mechanical properties, the mechanical properties except the splitting tensile strength are less influenced by the cement content, the elastic modulus and axial compressive strength as well as flexural tensile strength is largely affected by the replacement of cement by fly ash. The effect of the replacement of crushed limestone by lightweight aggregate is much more obvious on the cubic compressive strength than on the axial compressive strength, and larger on the flexural tensile strength than the splitting tensile strength.

Study of the use of kaolin waste as a partial substitute for fine aggregate in the production of concrete for pavers

2021 ◽  
Vol 2 (2) ◽  
pp. 2474-2489
Author(s):  
Thyago Lima Souza ◽  
Adriano Lopes Gualberto Filho ◽  
Deividy Kaik de Lima Araujo ◽  
Marcos André Lira Silva ◽  
Marco Antônio Assis De Oliveira ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Construction Industry ◽  
Strength Test ◽  
Raw Material ◽  
Fine Aggregate ◽  
Tensile Strength Test ◽  
Flexural Tensile Strength ◽  
Simple Compression

The study of the use of kaolin waste has scientific and socio-environmental value by providing an appropriate destination, reducing the demand and consequent problems arising from its extraction, considering that the construction industry is a consumer of a significant amount of raw material. Thus, the study aims to replace the fine aggregate by kaolin waste in the proportions of 10%, 20% and 30%, verifying its feasibility for interlocking sidewalk pieces. The kaolin waste was used with and without fine material, and physical characterization tests of the materials were performed, and then the concrete pieces were subjected to tests of resistance to simple compression, water absorption and resistance to abrasion, as prescribed by ABNT NBR 9781:2013, and flexural tensile strength test, according to ABNT NBR 12142:2010. According to the results and analyzing the compressive strength at 28 days, the mixtures with replacement of 10% of fine aggregate by kaolin waste reached strengths greater than 35 MPa, an acceptable normative parameter, both for the waste with fines and without fines, making its use feasible.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

scholarly journals Material-removing machining wastes as a filler of a polymer concrete (industrial chips as a filler of a polymer concrete)

2021 ◽  
Vol 28 (1) ◽  
pp. 343-351
Author(s):  
Norbert Kępczak ◽  
Radosław Rosik ◽  
Mariusz Urbaniak
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Young’S Modulus ◽  
Industrial Waste ◽  
Splitting Tensile Strength ◽  
Polymer Concrete ◽  
Strength Parameters ◽  
Basic Parameters ◽  
Natural Fillers

Abstract The paper presents an impact of the addition of industrial machining chips on the mechanical properties of polymer concrete. As an additional filler, six types of industrial waste machining chips were used: steel fine chips, steel medium chips, steel thick chips, aluminium fine chips, aluminium medium chips, and titanium fine chips. During the research, the influence of the addition of chips on the basic parameters of mechanical properties, i.e., tensile strength, compressive strength, splitting tensile strength, and Young’s modulus, was analyzed. On the basis of the obtained results, conclusions were drawn that the addition of chips from machining causes a decrease in the value of the mechanical properties parameters of the polymer concrete even by 30%. The mechanism of cracking of samples, which were subjected to durability tests, was also explored. In addition, it was found that some chip waste can be used as a substitute for natural fillers during preparation of a mineral cast composition without losing much of the strength parameters.

scholarly journals Roller Compacted Concrete with Recycled Concrete Aggregate for Paving Bases

2020 ◽  
Vol 12 (8) ◽  
pp. 3154 ◽  
Author(s):  
Hedelvan Emerson Fardin ◽  
Adriana Goulart dos Santos
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Modulus Of Elasticity ◽  
Splitting Tensile Strength ◽  
Recycled Concrete ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Roller Compacted Concrete ◽  
Flexural Tensile Strength ◽  
Mechanical And Physical Properties

This research aimed to investigate the mechanical and physical properties of Roller Compacted Concrete (RCC) used with Recycled Concrete Aggregate (RCA) as a replacement for natural coarse aggregate. The maximum dry density method was adopted to prepare RCC mixtures with 200 kg/m³ of cement content and coarse natural aggregates in the concrete mixture. Four RCC mixtures were produced from different RCA incorporation ratios (0%, 5%, 15%, and 30%). The compaction test, compressive strength, splitting tensile strength, flexural tensile strength, and modulus of elasticity, porosity, density, and water absorption tests were performed to analyze the mechanical and physical properties of the mixtures. One-way Analysis of Variance (ANOVA) was used to identify the influences of RCA on RCC’s mechanical properties. As RCA increased in mixtures, some mechanical properties were observed to decrease, such as modulus of elasticity, but the same was not observed in the splitting tensile strength. All RCCs displayed compressive strength greater than 15.0 MPa at 28 days, splitting tensile strength above 1.9 MPa, flexural tensile strength above 2.9 MPa, and modulus of elasticity above 19.0 GPa. According to Brazilian standards, the RCA added to RCC could be used for base layers.

Size Effect on Mechanical Properties of LVL

2014 ◽  
Vol 887-888 ◽  
pp. 824-829
Author(s):  
Qing Fang Lv ◽  
Ji Hong Qin ◽  
Ran Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Size Effect ◽  
Tensile Test ◽  
Compression Test ◽  
Test Results ◽  
Laminated Veneer Lumber ◽  
Object Of Study ◽  
The Relationship

Laminated veneer lumber is taken as an object of study, and use LVL specimens of different sizes for compression test and tensile test. The goal of the experiment is to investigate the size effect on compressive strength and tensile strength as well as the influence of the secondary glued laminated face, which appears in the secondary molding processes. The results show that both compressive strength and tensile strength have the size effect apparently and the existence of the secondary glued laminated face lower the compressive strength of LVL specimens. Afterwards, the relationship between compressive strength and volume along with tensile strength and area are obtained by the test results.

Effect of using magnetic water on the mechanical properties of concrete exposed to elevated temperature

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wasim Barham ◽  
Ammar AL-Maabreh ◽  
Omar Latayfeh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elevated Temperature ◽  
Flexural Strength ◽  
Tap Water ◽  
Splitting Tensile Strength ◽  
Content Type ◽  
Normal Water ◽  
Magnetic Water

PurposeThe influence of using magnetic water instead of tap water in the mechanical properties of the concrete exposed to elevated temperatures was investigated. Two concrete mixes were used and cast with the same ingredients. Tap water was used in the first mix and magnetic water was used in the second mix. A total of 48 specimens were cast and divided as follows: 16 cylinders for the concrete compressive strength test (8 samples for each mix), 16 cylinders for the splitting tensile strength (8 specimens for each mix) and 16 beams to test the influences of magnetized water on the flexural strength of concrete (8 specimens for each mixture). Specimens were exposed to temperatures of (25 °C, 200 °C, 400 °C and 600 °C). The experimental results showed that magnetic water highly affected the mechanical properties of concrete. Specimens cast and curried out with magnetic water show higher compressive strength, splitting tensile strength and flexural strength compared to normal water specimens at all temperatures. The relative strength range between the two types of water used was 110–123% for compressive strength and 110–133% for splitting strength. For the center point loading test, the relative flexural strength range was 118–140%. The use of magnetic water in mixing concrete contribute to a more complete hydration process.Design/methodology/approachExperimental study was carried out on two concrete mixes to investigate the effect of magnetic water. Mix#1 used normal water as the mixing water, and Mix#2 used magnetic water instead of normal water. After 28 days, all the samples were taken out of the tank and left to dry for seven days, then they were divided into different groups. Each group was exposed to a different temperature where it was placed in a large oven for two hours. Three different tests were carried out on the samples, these tests were concrete compressive strength, flexural strength and splitting tensile strength.FindingsExposure of concrete to high temperatures had a significant influence on concrete mechanical properties. Specimens prepared using magnetic water showed higher compressive strength at all temperature levels. The use of magnetic water in casting and curing concrete can increase the compressive strength by 23%. Specimens prepared using magnetic water show higher splitting tensile strength at all temperatures up to 33%. The use of magnetic water in casting and curing can strengthen and increase concrete resistance to high temperatures, a significant enhancement in flexural strength at all temperatures was found with a value up to 40%.Originality/valuePrevious research proved the advantages of using magnetic water for improving the mechanical properties of concrete under normal conditions. The potential of using magnetic water in the concrete industry in the future requires conducting extensive research to study the behavior of magnetized concrete under severe conditions to which concrete structures may be subjected to. These days, there are attempts to obtain stronger concrete with high resistance to harsh environmental conditions without adding new costly ingredients to its main mixture. No research has been carried out to investigate the effect of magnetic water on the mechanical properties of concrete exposed to elevated temperature. The main objective of this study is to evaluate the effect of using magnetic water on the mechanical properties of hardened concrete subjected to elevated temperature.

Sign in / Sign up

Export Citation Format

Share Document