Study of Smoke Stratification in Atrium Halls Using Scale Model

2009 ◽  
Author(s):  
N. K. Fong ◽  
C. H. Ko
Keyword(s):  
Air Temperature ◽  
Detection System ◽  
National Fire Protection Association ◽  
Ambient Air ◽  
Scale Model ◽  
Triangular Prism ◽  
Smoke Movement ◽  
Smoke Plume ◽  
Smoke Layer ◽  
Plume Temperature

Nowadays, atrium building is very popular because it can provide extensity and attraction to the users even if they are inside the enclosed environment. Similar to other buildings, fire safety is one of the major concerns especially the atrium are linked to shopping arcades. The major challenge is to control the smoke movement in the case of fire and maintain a stable smoke layer clear height to allow sufficient time for the occupants to evacuate from the building. Therefore, an efficient smoke management system (SMS) is necessary. For the SMS to function properly, the smoke behaviour inside the atrium must be studied. One of the phenomena affecting the operation of the SMS is smoke stratification. That is, due to the vertical temperature gradient inside the atrium, a thermally stratified environment is formed and smoke will not be able to reach the smoke detectors/smoke outlets in the ceiling. In the past decade, various studies were conducted to study the smoke filling process in the atrium. Only a few studies were carried out to study smoke stratification in atrium. This paper attempted to study the factors leading to the development of thermally stratified environment in an atrium and the formation of smoke stratification under the ceiling space of an atrium building using scale model. These factors included the temperature of the smoke plume, the air temperature under the ceiling, the configuration of roof ceiling and the ambient air temperature. Two types of ceiling configurations such as a cuboid and a triangular prism are used. Data concerning the ceiling air temperature, smoke plume temperature, effect of different ceiling configuration and maximum smoke layer height in a thermally stratified environment are collected. Comparisons are conducted with the calculated results from National Fire Protection Association (NFPA) 92B equations. With all these information, better design criteria of smoke detection system, SMS in an atrium building can be developed. Finally, the experimental results can be used to investigate the discrepancies between the experimental measurement and the calculated results from NFPA 92B equations. Put abstract text here.

Treatment of a Municipal Leachate Under Multi-Variable Conditions

1982 ◽  
Vol 17 (1) ◽  
pp. 135-148
Author(s):  
P.T. Wong ◽  
D.S. Mavinic
Keyword(s):  
Air Temperature ◽  
Nutrient Loading ◽  
Ambient Air ◽  
Removal Rates ◽  
Ambient Air Temperature

Abstract The treatability of a municipal leachate (BOD5 = 8090 mg/L) was investigated, by aerobic biostabilization, at a nutrient loading of BOD5:N:P of 100:3.2:1.1. The first stage effluents were subsequently polished by lime-magnesium coagulation. The ranges of ambient air temperature and sludge age studied were 5° to 25°C and 5 to 20 days, respectively. In the biostabilization phase, a BOD5:N:P loading of 100:3.2:1.1 was found to be “adequate” for treatment. Organic and metal removals in the first stage units were excellent. Under all conditions investigated, except for the two units close to washout conditions (5-day sludge age units at 5° and 10°C), BOD5 and COD removals of at least 99.4 and 96.4 percent, respectively, were achieved. Similarly, removal rates for most of the metals monitored were greater than 90 percent. In general, the removal of residual contaminants was not enhanced significantly by the addition of magnesium in the lime-magnesium polishing step.

scholarly journals 8-Day and Daily Maximum and Minimum Air Temperature Estimation via Machine Learning Method on a Climate Zone to Global Scale

2021 ◽  
Vol 13 (12) ◽  
pp. 2355
Author(s):  
Linglin Zeng ◽  
Yuchao Hu ◽  
Rui Wang ◽  
Xiang Zhang ◽  
Guozhang Peng ◽  
...  
Keyword(s):  
Spatial Scale ◽  
Air Temperature ◽  
Spatial Scales ◽  
Model Performance ◽  
Global Scale ◽  
Scale Model ◽  
Validation Dataset ◽  
Daily Maximum ◽  
Climate Zone ◽  
Temporal And Spatial

Air temperature (Ta) is a required input in a wide range of applications, e.g., agriculture. Land Surface Temperature (LST) products from Moderate Resolution Imaging Spectroradiometer (MODIS) are widely used to estimate Ta. Previous studies of these products in Ta estimation, however, were generally applied in small areas and with a small number of meteorological stations. This study designed both temporal and spatial experiments to estimate 8-day and daily maximum and minimum Ta (Tmax and Tmin) on three spatial scales: climate zone, continental and global scales from 2009 to 2018, using the Random Forest (RF) method based on MODIS LST products and other auxiliary data. Factors contributing to the relation between LST and Ta were determined based on physical models and equations. Temporal and spatial experiments were defined by the rules of dividing the training and validation datasets for the RF method, in which the stations selected in the training dataset were all included or not in the validation dataset. The RF model was first trained and validated on each spatial scale, respectively. On a global scale, model accuracy with a determination coefficient (R2) > 0.96 and root mean square error (RMSE) < 1.96 °C and R2 > 0.95 and RMSE < 2.55 °C was achieved for 8-day and daily Ta estimations, respectively, in both temporal and spatial experiments. Then the model was trained and cross-validated on each spatial scale. The results showed that the data size and station distribution of the study area were the main factors influencing the model performance at different spatial scales. Finally, the spatial patterns of the model performance and variable importance were analyzed. Both daytime and nighttime LST had a significant contribution in the 8-day Tmax estimation on all the three spatial scales; while their contribution in daily Tmax estimation varied over different continents or climate zones. This study was expected to improve our understanding of Ta estimation in terms of accuracy variations and influencing variables on different spatial and temporal scales. The future work mainly includes identifying underlying mechanisms of estimation errors and the uncertainty sources of Ta estimation from a local to a global scale.

scholarly journals Ambient Air Temperature Assisted Crystallization for Inorganic CsPbI2Br Perovskite Solar Cells

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3398
Author(s):  
Yi Long ◽  
Kun Liu ◽  
Yongli Zhang ◽  
Wenzhe Li
Keyword(s):  
Solar Cells ◽  
Air Temperature ◽  
High Performance ◽  
Defect Density ◽  
Perovskite Solar Cells ◽  
Ambient Air ◽  
Dark Phase ◽  
High Quality ◽  
Ambient Air Temperature ◽  
Air Atmosphere

Inorganic cesium lead halide perovskites, as alternative light absorbers for organic–inorganic hybrid perovskite solar cells, have attracted more and more attention due to their superb thermal stability for photovoltaic applications. However, the humid air instability of CsPbI2Br perovskite solar cells (PSCs) hinders their further development. The optoelectronic properties of CsPbI2Br films are closely related to the quality of films, so preparing high-quality perovskite films is crucial for fabricating high-performance PSCs. For the first time, we demonstrate that the regulation of ambient temperature of the dry air in the glovebox is able to control the growth of CsPbI2Br crystals and further optimize the morphology of CsPbI2Br film. Through controlling the ambient air temperature assisted crystallization, high-quality CsPbI2Br films are obtained, with advantages such as larger crystalline grains, negligible crystal boundaries, absence of pinholes, lower defect density, and faster carrier mobility. Accordingly, the PSCs based on as-prepared CsPbI2Br film achieve a power conversion efficiency of 15.5% (the maximum stabilized power output of 15.02%). Moreover, the optimized CsPbI2Br films show excellent robustness against moisture and oxygen and maintain the photovoltaic dark phase after 3 h aging in an air atmosphere at room temperature and 35% relative humidity (R.H.). In comparison, the pristine films are completely converted to the yellow phase in 1.5 h.

Evaluation of the influence of ambient air temperature and air velocity on mortar cement durability using a forced convection solar dryer

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Younes Bahammou ◽  
Mounir Kouhila ◽  
Haytem Moussaoui ◽  
Hamza Lamsyehe ◽  
Zakaria Tagnamas ◽  
...  
Keyword(s):  
Environmental Factors ◽  
Forced Convection ◽  
Air Temperature ◽  
Building Materials ◽  
Ambient Air ◽  
Physical Significance ◽  
Drying Process ◽  
Air Velocity ◽  
Content Type ◽  
Ambient Air Temperature

PurposeThis work aims to study the hydrothermal behavior of mortar cement toward certain environmental factors (ambient air temperature and air velocity) based on its drying kinetics data. The objective is to provide a better understanding and controlling the stability of mortar structures, which integrate the sorption phenomenon, drying process, air pressure and intrinsic characteristics. This leads to predict the comportment of mortar structures in relation with main environmental factors and minimize the risk of cracking mortar structures at an early age.Design/methodology/approachThermokinetic study was carried out in natural and forced convection solar drying at three temperatures 20, 30 and 40°C and three air velocities (1, 3 and 5 m.s-1). The empirical and semiempirical models tested successfully describe the drying kinetics of mortar. These models simulate the drying process of water absorbed by capillarity, which is the most common humidity transfer mechanism in building materials and contain parameters with physical significance, which integrate the effect of several environmental factors and intrinsic characteristics of mortar structures.FindingsThe models simulate the drying process of water absorbed by capillarity, which is the most common humidity transfer mechanism in building materials and contain parameters with physical significance, which integrate the effect of several environmental factors and intrinsic characteristics of mortar structures. The average activation energy obtained expressed the temperature effect on the mortar diffusivity. The drying constant and the diffusion coefficient can be used to predict the influence of these environmental factors on the drying behavior of various building materials and therefore on their durability.Originality/valueEvaluation of the effect of several environmental factors and intrinsic characteristics of mortar structures on their durability.

scholarly journals Direct Calculation of Thermodynamic Wet-Bulb Temperature as a Function of Pressure and Elevation

2013 ◽  
Vol 30 (8) ◽  
pp. 1757-1765 ◽  
Author(s):  
Sayed-Hossein Sadeghi ◽  
Troy R. Peters ◽  
Douglas R. Cobos ◽  
Henry W. Loescher ◽  
Colin S. Campbell
Keyword(s):  
Air Temperature ◽  
Mean Absolute Error ◽  
Direct Calculation ◽  
Ambient Air ◽  
Absolute Error ◽  
Mean Square ◽  
Air Temperatures ◽  
Order Polynomial ◽  
The Mean ◽  
Very High

Abstract A simple analytical method was developed for directly calculating the thermodynamic wet-bulb temperature from air temperature and the vapor pressure (or relative humidity) at elevations up to 4500 m above MSL was developed. This methodology was based on the fact that the wet-bulb temperature can be closely approximated by a second-order polynomial in both the positive and negative ranges in ambient air temperature. The method in this study builds upon this understanding and provides results for the negative range of air temperatures (−17° to 0°C), so that the maximum observed error in this area is equal to or smaller than −0.17°C. For temperatures ≥0°C, wet-bulb temperature accuracy was ±0.65°C, and larger errors corresponded to very high temperatures (Ta ≥ 39°C) and/or very high or low relative humidities (5% &lt; RH &lt; 10% or RH &gt; 98%). The mean absolute error and the root-mean-square error were 0.15° and 0.2°C, respectively.

scholarly journals Outdoor PM2.5, Ambient Air Temperature, and Asthma Symptoms in the Past 14 Days among Adults with Active Asthma

10.1289/ehp92 ◽  
2016 ◽  
Vol 124 (12) ◽  
pp. 1882-1890 ◽  
Author(s):  
Maria C. Mirabelli ◽  
Ambarish Vaidyanathan ◽  
W. Dana Flanders ◽  
Xiaoting Qin ◽  
Paul Garbe
Keyword(s):  
Air Temperature ◽  
Ambient Air ◽  
The Past ◽  
Asthma Symptoms ◽  
Ambient Air Temperature

EFFECTS OF LOW FLUCTUATING TEMPERATURES ON FARM ANIMALS.: III. INFLUENCE OF AMBIENT AIR TEMPERATURE ON FEED INTAKE OF LACTATING HOLSTEIN-FRIESIAN COWS

1958 ◽  
Vol 38 (2) ◽  
pp. 148-159 ◽  
Author(s):  
M. A. MacDonald ◽  
J. M. Bell
Keyword(s):  
Milk Production ◽  
Air Temperature ◽  
Low Temperatures ◽  
Ambient Air ◽  
Feed Consumption ◽  
Ambient Temperatures ◽  
Ambient Air Temperature ◽  
Holstein Friesian ◽  
Cent Level ◽  
Friesian Cows

This report presents effects of low temperatures on the feed consumption and efficiency of milk production of six mature, lactating, Holstein-Friesian cows that were confined in stanchions for three fortnightly experimental periods during which ambient temperatures measured in degree-hours per day (d-h/day) ranged from 110 to 1152 and daily minimum ambient air temperature (DMAAT) varied from 0° to 38°F. Applying results obtained, it was calculated that as temperatures decreased, i.e., d-h/day increased from 100 to 1200 and DMAAT decreased from 40° to 0°F, average daily intakes of total dry matter, hay, and gross and digestible Calories increased approximately 6.4 lb., 5.3 lb., 13 Therms and 9 Therms, respectively. Each of these increases was statistically significant at the 1 per cent level. Reductions in temperature also decreased gross and net caloric efficiencies of milk production approximately 10 and 8.5 per cent, respectively. These decreases were significant at the 2 per cent level. No correlation was evident between crude protein utilization and temperature.Results indicated that thermal stress was not overcome adequately by supplementary hay intake alone and that appetite stimulation by low temperatures had a carry-over effect continuing at least 24 hours. For continued efficient milk production during winters where low ambient temperatures are prevalent these results suggest it is necessary to provide some form of building insulation, ambient heat and/or provide a high energy supplement to otherwise adequate production rations.

scholarly journals Research On Solar Energy Collector With Cell Polycarbonate Absorber

2015 ◽  
Vol 1 ◽  
pp. 213
Author(s):  
Henriks Putāns ◽  
Viktorija Zagorska ◽  
Imants Ziemelis ◽  
Zanis Jesko
Keyword(s):  
Experimental Investigation ◽  
Solar Radiation ◽  
Air Temperature ◽  
Heat Carrier ◽  
Heat Insulation ◽  
Ambient Air ◽  
Maximum Temperature ◽  
Experimental Examination ◽  
Ambient Air Temperature ◽  
Flat Plate Solar Collector

A flat plate solar collector with cell polycarbonate absorber and transparent cover has been made and its experimental investigation carried out. The collector consists of a wooden box, into which, a layer of heat insulation with a mirror film and 4 mm thick cell polycarbonate sheet, as the absorber, are placed. The coherence between collector’s efficiency, heat carrier and ambient air temperature, as well as intensity of the solar radiation and heat power in the experimental investigation has been obtained. During the experimental examination the maximum temperature of the heat carrier reached 80˚C at the intensity of solar radiation about 0.8 kW/m2 and ambient air temperature around 32˚C. The efficiency of the collector reached 33-60%, depending on the intensity of solar radiation and surrounding air temperature.

scholarly journals Edge Cooling of a Fuel Cell during Aerial Missions by Ambient Air

Micromachines ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1432
Author(s):  
Lev Zakhvatkin ◽  
Alex Schechter ◽  
Eilam Buri ◽  
Idit Avrahami
Keyword(s):  
Fuel Cell ◽  
Numerical Model ◽  
Wind Tunnel ◽  
Boundary Conditions ◽  
Air Temperature ◽  
Numerical Models ◽  
Heat Removal ◽  
Ambient Air ◽  
Experimental Setup ◽  
Good Agreement

During aerial missions of fuel-cell (FC) powered drones, the option of FC edge cooling may improve FC performance and durability. Here we describe an edge cooling approach for fixed-wing FC-powered drones by removing FC heat using the ambient air during flight. A set of experiments in a wind tunnel and numerical simulations were performed to examine the efficiency of FC edge cooling at various flight altitudes and cruise speeds. The experiments were used to validate the numerical model and prove the feasibility of the proposed method. The first simulation duplicated the geometry of the experimental setup and boundary conditions. The calculated temperatures of the stack were in good agreement with those of the experiments (within ±2 °C error). After validation, numerical models of a drone’s fuselage in ambient air with different radiator locations and at different flight speeds (10–30 m/s) and altitudes (up to 5 km) were examined. It was concluded that onboard FC edge cooling by ambient air may be applicable for velocities higher than 10 m/s. Despite the low pressure, density, and Cp of air at high altitudes, heat removal is significantly increased with altitude at all power and velocity conditions due to lower air temperature.

Sign in / Sign up

Export Citation Format

Share Document