Geotechnical Centrifuge Modelling Techniques for Submarine Slides

Author(s):  
N. Boylan ◽  
C. Gaudin ◽  
D. J. White ◽  
M. F. Randolph ◽  
J. A. Schneider

The gradual shift of hydrocarbon developments into deeper waters has presented fresh challenges for offshore geotechnical engineering. Many installations in deep water require export pipelines to shore which can be many hundreds of kilometers in length. These pipelines must negotiate unstable regions of soft seabed around the steep continental shelf and variable terrain including canyons with depths ranging from tens of meters to a several hundred meters. These challenging conditions present potential geohazards for which little understanding has been developed so far. One of the major geohazards is the impact of a submarine landslide on nearby pipelines which could potentially damage the pipeline. Consequently, a Joint Industry Project (JIP) has been initiated at the Centre for Offshore Foundation Systems to improve methods for assessing the potential damage to pipelines and to provide information to assist re-routing of a pipeline to a safer alignment if necessary. This paper presents an overview of the development of specific modeling techniques to (i) trigger a submarine landslide in a geotechnical centrifuge, (ii) measure the strength properties of the slide material before, during, and after the slide failure and (iii) measure the interaction between the runout material and the seabed.

TAPPI Journal ◽  
2016 ◽  
Vol 15 (10) ◽  
pp. 643-651 ◽  
Author(s):  
ROBERT J. OGLESBY ◽  
HUMPHREY J. MOYNIHAN ◽  
RICARDO B. SANTOS ◽  
ASHOK GHOSH ◽  
PETER W. HART

The impact of commercially prepared, fully bleached pulp viscosity variation on handsheet physical properties was evaluated at different levels of pulp refining. Hardwood pulps from the same brownstock species mix, cooking parameters, and kappa numbers were processed through two different commercial bleach plants: one with a D0(EP)D1D2 sequence and the second with an OD0(EOP)D1 sequence. Additionally, a commercial softwood (predominately Scotts pine) brownstock pulp bleached by an OD0(EP)D1D2 sequence was employed in this study. Pulps with viscosities ranging from 14 to 21 mPa∙s were refined in a Valley beater to two freeness levels, and the associated handsheet physical properties were measured in this study. Over the pulp viscosity range of 14 to 21 mPa∙s, no clear correlation was found to exist between pulp viscosity and related paper physical properties. Finally, a series of laboratory prepared bleached pulps were purposely prepared under non-ideal conditions to reduce their final viscosities to lower values. Handsheets made from these pulps were tested in their unbeaten condition for physical strength properties. Significant and rapid strength loss occurred when the measured pulp viscosity dropped below 12 mPa∙s; overall strength properties showed no correlation to viscosity above the critical 12 mPa∙s value.


Author(s):  
Saeed Delara ◽  
Kendra MacKay

Horizontal directional drilling (HDD) has become the preferred method for trenchless pipeline installations. Drilling pressures must be limited and a “no-drill zone” determined to avoid exceeding the strength of surrounding soil and rock. The currently accepted industry method of calculating hydraulic fracturing limiting pressure with application of an arbitrary safety factor contains several assumptions that are often not applicable to specific ground conditions. There is also no standard procedure for safety factor determination, resulting in detrimental impacts on drilling operations. This paper provides an analysis of the standard methods and proposes two alternative analytical models to more accurately determine the hydraulic fracture point and acceptable drilling pressure. These alternative methods provide greater understanding of the interaction between the drilling pressures and the surrounding ground strength properties. This allows for more accurate determination of horizontal directional drilling limitations. A comparison is presented to determine the differences in characteristics and assumptions for each model. The impact of specific soil properties and factors is investigated by means of a sensitivity analysis to determine the most critical soil information for each model.


Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1103
Author(s):  
Sara Sarraj ◽  
Małgorzata Szymiczek ◽  
Tomasz Machoczek ◽  
Maciej Mrówka

Eco-friendly composites are proposed to substitute commonly available polymers. Currently, wood–plastic composites and natural fiber-reinforced composites are gaining growing recognition in the industry, being mostly on the thermoplastic matrix. However, little data are available about the possibility of producing biocomposites on a silicone matrix. This study focused on assessing selected organic fillers’ impact (ground coffee waste (GCW), walnut shell (WS), brewers’ spent grains (BSG), pistachio shell (PS), and chestnut (CH)) on the physicochemical and mechanical properties of silicone-based materials. Density, hardness, rebound resilience, and static tensile strength of the obtained composites were tested, as well as the effect of accelerated aging under artificial seawater conditions. The results revealed changes in the material’s properties (minimal density changes, hardness variation, overall decreasing resilience, and decreased tensile strength properties). The aging test revealed certain bioactivities of the obtained composites. The degree of material degradation was assessed on the basis of the strength characteristics and visual observation. The investigation carried out indicated the impact of the filler’s type, chemical composition, and grain size on the obtained materials’ properties and shed light on the possibility of acquiring ecological silicone-based materials.


Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3430
Author(s):  
Grzegorz Golański ◽  
Jacek Słania ◽  
Marek Sroka ◽  
Paweł Wieczorek ◽  
Michał Urzynicok ◽  
...  

In addition to good high-temperature creep resistance and adequate heat resistance, steels for the power industry must have, among other things, good weldability. Weldability of such steels is one of the criteria determining whether or not the material is suitable for applications in the power industry. Therefore, when materials such as martensitic steel Thor 115 (T115) are introduced into the modern power industry, the quality and properties of welded joints must be assessed. The paper presents the results of metallographic and mechanical investigations of T115 martensitic steel welded joints. The analysis was carried out on joints welded with two filler metals: WCrMo91 (No. 1) and EPRI P87 (No. 2). The scope of the investigations included: microstructural investigations carried out using optical, scanning and transmission electron microscopy and mechanical testing, i.e., Vickers microhardness and hardness measurement, static tensile test and impact test. The macro- and microstructural investigations revealed correct structure of the weld, without welding imperfections. The microstructural investigations of joint No. 1 revealed a typical structure of this type of joint, i.e., the martensitic structure with numerous precipitates, while in joint No. 2, the so-called Nernst’s layers and δ-ferrite patches were observed in the weld fusion zone as well as the heat affected zone (HAZ). The mechanical properties of the test joints met the requirements for the base material. A slight influence of the δ-ferrite patch on the strength properties of joint No. 2 was observed, and its negative effect on the impact energy of HAZ was visible.


Author(s):  
R. K. Vagapov

The impact of hydrogen sulfide raw materials on steel equipment and pipelines is associated not only with corrosion processes, but also with the hydrogenation of used carbon and low-alloy steels. This can lead to the loss of their strength properties and the subsequent destruction of equipment operated under conditions of increased operating pressures. Such corrosive-mechanical effects associated with the penetration of hydrogen into steel are the most dangerous from the point of view of the safety and reliability of the operation of facilities for the production of hydrocarbon fluids. The effect of H2S on the main types of structural steels was investigated according to the results of autoclave tests. The formation of blistering (blistering) and cracks on the surface of steels due to the effect of hydrogen on the steel was recorded. A study of the phase composition of corrosion products and their possible effect on the processes of corrosion and hydrogenation of steel has been carried out.


2021 ◽  
Author(s):  
Pablo Poulain ◽  
Anne Le Friant ◽  
Rodrigo Pedreros ◽  
Anne Mangeney ◽  
Andrea Filippini ◽  
...  

<p>Since May 2018, Mayotte island has experienced an important seismic activity linked to the on-going sismo-volcanic crisis. The epicenters of the seismic swarms are located between 5 and 15 km east of Petite Terre for the main swarm, and 25 km east of Petite Terre for the secondary swarm. Although variations in the number of earthquakes and their distribution have been observed since the start of the eruption in early July 2018 [Lemoine A.(2020), Cesca et al.(2020)], a continuous seismicity persists and could generate several earthquakes of magnitudes close to M4 widely felt by the population. This recurrent seismicity could weaken the steep submarine slopes of Mayotte, as highlighted by the high resolution bathymetry data collected during the MAYOBS cruise in May 2019 (Feuillet et al.,submitted) and trigger submarine landslides with associated tsunamis.</p><p>To address the hazards associated with such events, we analyzed morphological data to define 8 scenarios of potential submarine slides with volumes ranging from 11,25.10<sup>6</sup> to 800.10<sup>6</sup> m<sup>3</sup> and we simulate the landslide dynamics and generated waves. We use two complementary numerical models: (i) the code HYSEA to simulate the dynamic of the submarine granular flows and the water wave generation, and (ii) the Boussinesq FUNWAVE- TVD model simulate the waves propagation and the inundation on Mayotte. The effect of the time at which the models are coupled is investigated.</p><p>The most impacting submarine slide scenarios are located close to Petite Terre at a shallow depth. They can locally generate a sea surface elevation more than a meter in local areas especially at Petite Terre. The various simulations show that parts of the island are particularly sensitive to the risk of tsunamis. Indeed, some scenarios that does not cause significant coastal flooding still seems to cause significant hazards in these exposed areas. The barrier reef around Mayotte has a prominent role in controlling the wave propagation towards the island and therefore reducing the impact on land. It should be noted that the arrival of tsunamis on the coastline is not necessarily preceded by a retreat from the sea and the waves can reach the coasts of Mayotte very quicky (few minutes).</p><p> </p><p>Cesca, S., Letort, J., Razafindrakoto, H.N.T. et al. Drainage of a deep magma reservoir near Mayotte inferred from seismicity and deformation. Nat. Geosci. <strong>13, </strong>87–93 (2020). https://doi.org/10.1038/s41561-019-0505-5</p><p>Feuillet, N, Jorry, S. J., Crawford, W, Deplus, C. Thinon, I, Jacques, E. Saurel, J.M., Lemoine, A., Paquet, F., Daniel, R., Gaillot, A., Satriano, C., Peltier, A., Aiken, C., Foix, O., Kowalski, P., Laurent, A., Beauducel, F., Grandin, R., Ballu, V., Bernard, P., Donval, J.P., Geli, L., Gomez, J. Guyader, V., Pelleau, P., Rinnert, E., Bertil, D., Lemarchand, A., Van der Woerd, J.et al. (in rev). Birth of a large volcano offshore Mayotte through lithosphere-scale rifting, Nature.</p><p>Anne Lemoine, Pierre Briole, Didier Bertil, Agathe Roullé, Michael Foumelis, Isabelle Thinon, Daniel Raucoules, Marcello de Michele, Pierre Valty, Roser Hoste Colomer, The 2018–2019 seismo-volcanic crisis east of Mayotte, Comoros islands: seismicity and ground deformation markers of an exceptional submarine eruption, Geophysical Journal International, Volume 223, Issue 1, October 2020, Pages 22–44, https://doi.org/10.1093/gji/ggaa273</p>


2017 ◽  
Vol 869 ◽  
pp. 50-61
Author(s):  
Matthias Sabel ◽  
Christian Sator ◽  
Ralf Müller ◽  
Benjamin Kirsch

The formation of chips in cutting processes is characterised by large deformations and large configurational changes and therefore challenges established modeling techniques. To overcome these difficulties, the particle finite element method (PFEM) combines the benefits of discrete modeling techniques with methods based on continuum mechanics. In this work an outline of the PFEM, as well as an explanation of the finite element formulation are provided. The impact of the boundary detection on the structural integrity is studied. The numerical examples include a tensile test as well as cutting simulations. The paper is concluded by a comparison of cutting forces with analytical results.


2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Sarath Chandra K ◽  
Krishnaiah S ◽  
Kibebe Sahile

Industrialization is the key to the growth of any country’s economy. However, on the other hand, the production of industrial waste is increasing enormously, which adversely impacts the environment and natural resources. Red mud is also a widespread industrial waste produced during aluminium extraction from bauxite ore in Bayer’s process. Red mud is a highly alkaline material that creates a massive environmental threat in nature. To reduce the impact of this solid waste material, the ideal method is to use it in construction works with appropriate stabilization. This study envisages the strength properties of red mud with fly ash and cement to use it as a road construction material in the subgrade. The influence of fly ash and cement on improving the strength properties of red mud was studied in detail by replacing red mud with 10%, 20%, and 30% with fly ash and 1%, 3%, and 5% of cement to its dry weight. The CBR (California bearing ratio) value was increased from 1.58% to 11.6% by stabilizing red mud with fly ash and cement, which can be used as a road construction material. The UCS (unconfined compressive strength) of red mud was increased from 825 kPa to 2340 kPa upon curing for 28 days with the right mix of fly ash and cement. Along with the strength properties, the chemical analysis of leachate for the best suitable mix was performed according to the TCLP method to understand the hazardous materials present in the red mud when it is injected as ground material. Both strength properties and the leachate characteristics prove that the red mud with suitable fly ash and cement is an excellent material in road constructions.


2019 ◽  
Vol 130 ◽  
pp. 01023
Author(s):  
Pritamara Wahyuningtyas ◽  
Anne Zulfia Syahrial ◽  
Wahyuaji Narottama Putra ◽  
Budi Wahyu Utomo

A study of ADC12 (Al-Si aluminium alloy) composite is conducted to obtain a more sustainable material with enhanced properties for automotive industry purpose, such as train's brake shoe and bearing application. For those kind of utilization, material with durability, good elastic modulus, thermal stability, wear resistance, and high strength properties is needed due to its exposure to high temperature and heavy continuous application. ADC 12 acts as the matrix, reinforced with 3 vf% micro-SiC with 5 wt% Mg wetting agent was fabricated by the stir casting method. The addition of 0.18 wt% Sr and 0.15 wt% TiB were expected to finer the grain morphology of the silicone eutectic phase and to acts as the grain refiner, respectively. Furthermore, T6 heat treatment was applied with aging temperature 150 °C, 170 °C, 190 °C, 210 °C, and 230 °C, following the prior 1 h 490 °C solution treatment. The results obtained in this work showed enhancement in tensile strength with the value of 213 MPa, hardness value 75 HRB, and wear resistance. These values increase up to 115 MPa for the UTS and 38 HRB for the hardness value, as the impact of the refined grains from both modifiers and heat treatment.


2020 ◽  
Vol 110 (6) ◽  
pp. 829-832
Author(s):  
Amanda Y. Kong ◽  
Xingyou Zhang

Interest in the impact of the built environment on health behaviors, outcomes, and disparities is increasing, and the growing development of statistical modeling techniques has allowed researchers to better investigate these relationships. However, without enough data that are identifiable at smaller geographic levels (e.g., census tract), place-based health researchers are unable to reliably estimate the prevalence of a health outcome at these more granular and potentially more salient neighborhood levels. When reliable direct survey estimates cannot be produced because of small samples or a lack of samples, estimates based on small area estimation techniques are often used. As place-based health research and the production and secondary use of small area estimates increase, it is critical that researchers understand both the underlying methods used to create these estimates and their limitations. Without this foundation, researchers may fit inappropriate models, or interpret findings inaccurately. As a demonstrative example, we focus this discussion on the small area health indicator estimates recently produced through the 500 Cities Project by the Robert Wood Johnson Foundation, the Centers for Disease Control and Prevention (CDC), and the CDC Foundation.


Sign in / Sign up

Export Citation Format

Share Document