scholarly journals Gas flow through atomic-scale apertures

2020 ◽  
Vol 6 (51) ◽  
pp. eabc7927
Author(s):  
Jothi Priyanka Thiruraman ◽  
Sidra Abbas Dar ◽  
Paul Masih Das ◽  
Nasim Hassani ◽  
Mehdi Neek-Amal ◽  
...  
Keyword(s):  
Gas Flow ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Atomic Scale ◽  
Gas Flows ◽  
Narrow Channels ◽  
Molecular Separation ◽  
Transmission Electron ◽  
Ultralow Concentrations ◽  
Atomic Limit

Gas flows are often analyzed with the theoretical descriptions formulated over a century ago and constantly challenged by the emerging architectures of narrow channels, slits, and apertures. Here, we report atomic-scale defects in two-dimensional (2D) materials as apertures for gas flows at the ultimate quasi-0D atomic limit. We establish that pristine monolayer tungsten disulfide (WS2) membranes act as atomically thin barriers to gas transport. Atomic vacancies from missing tungsten (W) sites are made in freestanding (WS2) monolayers by focused ion beam irradiation and characterized using aberration-corrected transmission electron microscopy. WS2 monolayers with atomic apertures are mechanically sturdy and showed fast helium flow. We propose a simple yet robust method for confirming the formation of atomic apertures over large areas using gas flows, an essential step for pursuing their prospective applications in various domains including molecular separation, single quantum emitters, sensing and monitoring of gases at ultralow concentrations.

Fuel-Matrix Chemical Interaction between U-7wt.%Mo Alloy and Mg

2013 ◽  
Vol 333 ◽  
pp. 199-206 ◽  
Author(s):  
K. Huang ◽  
H. Heinrich ◽  
D.D. Keiser ◽  
Yong Ho Sohn
Keyword(s):  
Electron Microscopy ◽  
Focused Ion Beam ◽  
Chemical Interaction ◽  
Ion Beam ◽  
Equilibrium Phase ◽  
Atomic Scale ◽  
Inert Matrix ◽  
Transmission Electron ◽  
Test Reactor

A solid-to-solid, U-7wt.%Mo vs. Mg diffusion couple was assembled and annealed at 550°C for 96 hours. Themicrostructurein the interdiffusion zone and the development of concentration profiles were examined via scanning electron microscopy, transmission electron microscopy (TEM) and X-ray energy dispersive spectroscopy. A TEM specimen was prepared at the interface between U-7wt.%Mo andMgusing focused ion beam in-situ lift-out. The U-7wt.%Mo alloy was bonded well tothe Mg at the atomic scale, without any evidence of oxidation, cracks or pores.Despite the good bonding, very little or negligible interdiffusion was observed.This is consistent with the expectation based on negligible solubilities according to the equilibrium phase diagrams. Along with other desirableproperties, Mgis a potential inert matrix or barrier materialfor U-Mo fuel alloy systembeing developed forthe Reduced Enrichment for Research and Test Reactor (RERTR) program.

scholarly journals Characterization of a Si-SiO2 Mixture Generated from SiO(g) and CO(g)

2019 ◽  
Vol 50 (6) ◽  
pp. 2667-2680 ◽  
Author(s):  
Andrea Broggi ◽  
Merete Tangstad ◽  
Eli Ringdalen
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Flow ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Liquid Silicon ◽  
Inert Gas ◽  
Dissolved Carbon ◽  
Sic Particles ◽  
Transmission Electron ◽  
A Minor

Abstract The reaction between SiO(g) and CO(g) is a relevant intermediate reaction in the silicon production process. One of the products generated from this gas mixture is called by its color, brown condensate. In this paper, SiO(g) and CO(g) are produced from SiO2-SiC pellets. The reaction between the two gases occurred on SiC particles. Inert gas was injected at different flows. The SiC particles were collected, and the brown condensate deposited on them was characterized by electron probe microanalysis, X-ray photoelectron spectroscopy, and focused ion beam preparation samples for transmission electron microscope analysis. The brown condensate consists of a mixture of Si spheres embedded in a SiO2 matrix. The compound generates in the temperature range from 1400 °C to 1780 °C (1673 K to 2053 K), and in the SiO(g) partial pressure range between 0.534 and 0.742, depending on the inert gas flow. SiC crystallites are located at the Si-SiO2 interface. Carbides are believed to generate from the reaction between liquid silicon and CO(g). Carbides may also precipitate from reaction between dissolved carbon and liquid silicon, but to a minor extent. Both mechanisms are believed to happen above the melting point of silicon and in the softening range of silica.

Energy-Filtered Transmission Electron Microscopy of Multilayers in Semiconductors

1998 ◽  
Vol 523 ◽  
Author(s):  
C. P. Liu ◽  
C. B. Boothroyd ◽  
C. J. Humphreys
Keyword(s):  
Focused Ion Beam ◽  
Signal To Noise Ratio ◽  
Ion Beam ◽  
Atomic Scale ◽  
Atomic Fraction ◽  
Energy Losses ◽  
Uniform Thickness ◽  
Signal To Noise ◽  
Characteristic Energy ◽  
Transmission Electron

AbstractKnowledge about compositional profiles on an atomic scale is important for semiconductor multilayers. In this paper, we attempt to quantify the Ti atomic fraction in a TixAll–xN multilayer and the total As concentrations in As δ-doped layers using energy-filtered imaging. These two materials represent materials where the characteristic energy loss edges are located in widely different energy losses with the L edge of Ti being above 450eV and that of As around 1350eV. The accuracy of the Ti atomic fraction in TixAll–xN is found to be around 10at% for specimens of uniform thickness made by focused ion beam milling, whereas the resolution and As concentration for the As containing δ-layer is found to be dominated by the signal to noise ratio.

Low Energy Ar Ion Milling of FIB TEM Specimens from 14 nm and Future FinFET Technologies

2018 ◽  
Author(s):  
C.S. Bonifacio ◽  
P. Nowakowski ◽  
M.J. Campin ◽  
M.L. Ray ◽  
P.E. Fischione
Keyword(s):  
Field Effect Transistor ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Ion Milling ◽  
Transmission Electron ◽  
High Resolution Tem ◽  
Effect Transistor ◽  
20 Nm ◽  
Argon Ion

Abstract Transmission electron microscopy (TEM) specimens are typically prepared using the focused ion beam (FIB) due to its site specificity, and fast and accurate thinning capabilities. However, TEM and high-resolution TEM (HRTEM) analysis may be limited due to the resulting FIB-induced artifacts. This work identifies FIB artifacts and presents the use of argon ion milling for the removal of FIB-induced damage for reproducible TEM specimen preparation of current and future fin field effect transistor (FinFET) technologies. Subsequently, high-quality and electron-transparent TEM specimens of less than 20 nm are obtained.

TEM Sample Preparation Tricks for Advanced DRAMs

2015 ◽  
Author(s):  
Ching Shan Sung ◽  
Hsiu Ting Lee ◽  
Jian Shing Luo
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Tem Analysis ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Characterization Of Materials

Abstract Transmission electron microscopy (TEM) plays an important role in the structural analysis and characterization of materials for process evaluation and failure analysis in the integrated circuit (IC) industry as device shrinkage continues. It is well known that a high quality TEM sample is one of the keys which enables to facilitate successful TEM analysis. This paper demonstrates a few examples to show the tricks on positioning, protection deposition, sample dicing, and focused ion beam milling of the TEM sample preparation for advanced DRAMs. The micro-structures of the devices and samples architectures were observed by using cross sectional transmission electron microscopy, scanning electron microscopy, and optical microscopy. Following these tricks can help readers to prepare TEM samples with higher quality and efficiency.

Focused Ion Beam Analysis of Low-K Dielectrics

2000 ◽  
Author(s):  
H. J. Bender ◽  
R. A. Donaton
Keyword(s):  
Electron Microscope ◽  
Cross Section ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Single Step ◽  
Specimen Preparation ◽  
Transmission Electron ◽  
Beam Analysis ◽  
Low K ◽  
Scanning Electron

Abstract The characteristics of an organic low-k dielectric during investigation by focused ion beam (FIB) are discussed for the different FIB application modes: cross-section imaging, specimen preparation for transmission electron microscopy, and via milling for device modification. It is shown that the material is more stable under the ion beam than under the electron beam in the scanning electron microscope (SEM) or in the transmission electron microscope (TEM). The milling of the material by H2O vapor assistance is strongly enhanced. Also by applying XeF2 etching an enhanced milling rate can be obtained so that both the polymer layer and the intermediate oxides can be etched in a single step.

Fin Level Defect Isolation Inside a FinFET Using Electron Beam Alteration of Current Flow

2017 ◽  
Author(s):  
H.J. Ryu ◽  
A.B. Shah ◽  
Y. Wang ◽  
W.-H. Chuang ◽  
T. Tong
Keyword(s):  
Electron Microscopy ◽  
Electron Beam ◽  
Focused Ion Beam ◽  
Current Flow ◽  
Ion Beam ◽  
The Body ◽  
Complete Understanding ◽  
Root Cause ◽  
Transmission Electron ◽  
Defect Isolation

Abstract When failure analysis is performed on a circuit composed of FinFETs, the degree of defect isolation, in some cases, requires isolation to the fin level inside the problematic FinFET for complete understanding of root cause. This work shows successful application of electron beam alteration of current flow combined with nanoprobing for precise isolation of a defect down to fin level. To understand the mechanism of the leakage, transmission electron microscopy (TEM) slice was made along the leaky drain contact (perpendicular to fin direction) by focused ion beam thinning and lift-out. TEM image shows contact and fin. Stacking fault was found in the body of the silicon fin highlighted by the technique described in this paper.

Transmission Electron Microscopy (TEM) Specimen Preparation Technique using Focused Ion Beam (FIB): Application to Material Characterization of Chemical Vapor Deposition of Tungsten (W) and Tungsten Silicides (WSix)

1997 ◽  
Author(s):  
K. Doong ◽  
J.-M. Fu ◽  
Y.-C. Huang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Chemical Vapor ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Transmission Electron

Abstract The specimen preparation technique using focused ion beam (FIB) to generate cross-sectional transmission electron microscopy (XTEM) samples of chemical vapor deposition (CVD) of Tungsten-plug (W-plug) and Tungsten Silicides (WSix) was studied. Using the combination method including two axes tilting[l], gas enhanced focused ion beam milling[2] and sacrificial metal coating on both sides of electron transmission membrane[3], it was possible to prepare a sample with minimal thickness (less than 1000 A) to get high spatial resolution in TEM observation. Based on this novel thinning technique, some applications such as XTEM observation of W-plug with different aspect ratio (I - 6), and the grain structure of CVD W-plug and CVD WSix were done. Also the problems and artifacts of XTEM sample preparation of high Z-factor material such as CVD W-plug and CVD WSix were given and the ways to avoid or minimize them were suggested.

To Eliminate Curtain Effect of FIB TEM Samples by a Combination of Sample Dicing and Backside Milling

2014 ◽  
Author(s):  
Jian-Shing Luo ◽  
Hsiu Ting Lee
Keyword(s):  
Sample Preparation ◽  
Focused Ion Beam ◽  
Preparation Method ◽  
Low Cost ◽  
Ion Beam ◽  
Sample Preparation Method ◽  
Site Specific ◽  
Dual Beam ◽  
Transmission Electron

Abstract Several methods are used to invert samples 180 deg in a dual beam focused ion beam (FIB) system for backside milling by a specific in-situ lift out system or stages. However, most of those methods occupied too much time on FIB systems or requires a specific in-situ lift out system. This paper provides a novel transmission electron microscopy (TEM) sample preparation method to eliminate the curtain effect completely by a combination of backside milling and sample dicing with low cost and less FIB time. The procedures of the TEM pre-thinned sample preparation method using a combination of sample dicing and backside milling are described step by step. From the analysis results, the method has applied successfully to eliminate the curtain effect of dual beam FIB TEM samples for both random and site specific addresses.

A Methodology to Reduce Ion Beam Induced Damage in TEM Specimens Prepared by FIB

2002 ◽  
Author(s):  
Chin Kai Liu ◽  
Chi Jen. Chen ◽  
Jeh Yan.Chiou ◽  
David Su
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Tem Analysis ◽  
Sensitive Issue ◽  
Transmission Electron

Abstract Focused ion beam (FIB) has become a useful tool in the Integrated Circuit (IC) industry, It is playing an important role in Failure Analysis (FA), circuit repair and Transmission Electron Microscopy (TEM) specimen preparation. In particular, preparation of TEM samples using FIB has become popular within the last ten years [1]; the progress in this field is well documented. Given the usefulness of FIB, “Artifact” however is a very sensitive issue in TEM inspections. The ability to identify those artifacts in TEM analysis is an important as to understanding the significance of pictures In this paper, we will describe how to measure the damages introduced by FIB sample preparation and introduce a better way to prevent such kind of artifacts.

Sign in / Sign up

Export Citation Format

Share Document