Mechanical Properties of Human Mitral Valve Chordae Tendineae: Variation with Size and Strain Rate

1975 ◽  
Vol 53 (3) ◽  
pp. 330-339 ◽  
Author(s):  
Koon O. Lim ◽  
Derek R. Boughner
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Collagen Fibers ◽  
Elastic Response ◽  
Uniaxial Tensile ◽  
Prosthetic Heart Valves ◽  
Strain Rates ◽  
Valve Closure ◽  
Chordae Tendineae ◽  
Physiological Strain

A knowledge of the mechanical properties of valve tissue is a necessary prerequisite for a better understanding of valvular behavior and the design of prosthetic heart valves. Elastic response of chordae tendineae under strain rates of 0.05 cm min−1(6.25% min−1) to 12.7 cm min−1 (1600% min−1) were obtained by the application of an uniaxial tensile stress using an Instron machine. The chordae exhibited viscoelastic properties in that extensibility decreased with increasing strain rates. The approximate maximum physiological strain rate of the chordae was estimated from echocardiographic traces at the instant of valve closure, and a high value of 29 (S.D. = 9) cm s−1 (2000% s−1) was found. The breaking strain and stress were found to have values of 21.4 ± 0.5% and 3.1 ± 0.1 × 108 dyn cm−2 respectively, and were independent of strain rates (1 dyn = 10−5 N). These values are typical of collagen fibers. The final modulus, before the proportional limit, was found to be about 109 dyn cm−2, which is again typical of collagen fibers. In addition, smaller chordae exhibited less extensibility than the larger chordae. This behavior could be due to structural and functional differences and allows the more centrally inserted chordae to maintain an even valve surface during valve closure.

scholarly journals The Influence of Microstructure on the Mechanical Properties and Fracture Behavior of Medium Mn Steels at Different Strain Rates

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4228 ◽  
Author(s):  
Zheng Wang ◽  
Juanping Xu ◽  
Yu Yan ◽  
Jinxu Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Total Elongation ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Car Crash ◽  
Δ Ferrite

The primary task of automotive industry materials is to guarantee passengers’ safety during a car crash. To simulate a car crash, the influence of strain rates on mechanical properties and fracture behavior of medium Mn steels with different Si content (0Si without δ-ferrite and 0.6Si with about 20% δ-ferrite) was conducted using the uniaxial tensile test. The results show that ultimate tensile strength is higher, whereas total elongation is lower in 0Si than in 0.6Si. As the strain rate increases, ultimate tensile strength and total elongation decrease in both 0Si and 0.6Si; nonetheless, total elongation of 0.6Si decreases faster. Meanwhile, the area reduction of 0.6Si increases as the strain rate increases. The microcrack′s number on a rolling direction (RD)-transverse direction (TD) surface is considerably increased; nonetheless, the microcrack′s size is restrained in 0.6Si compared with 0Si. Microcracks start at γ(α′)/α-ferrite interfaces in both 0Si and 0.6Si, whereas little nucleation sites have also been found at (γ(α′)+α-ferrite)/δ-ferrite boundaries in 0.6Si. Meanwhile, δ-ferrite reveals a higher capacity for microcrack arrest. As the strain rate decreases, increased lower crack growth results in fine and even dimples on fractographs with abundant second cracks on fractographs; meanwhile, the small microcrack′s number increases, while the large microcrack′s number decreases on an RD-TD surface.

scholarly journals A Review on Mechanical Properties of Natural Fibre Reinforced Polymer Composites under Various Strain Rates

2021 ◽  
Vol 5 (5) ◽  
pp. 130
Author(s):  
Tan Ke Khieng ◽  
Sujan Debnath ◽  
Ernest Ting Chaw Liang ◽  
Mahmood Anwar ◽  
Alokesh Pramanik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Polymer Composites ◽  
Stress Transfer ◽  
Natural Fibre ◽  
Transfer Efficiency ◽  
Strain Rates ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Fibre Matrix

With the lightning speed of technological evolution, the demand for high performance yet sustainable natural fibres reinforced polymer composites (NFPCs) are rising. Especially a mechanically competent NFPCs under various loading conditions are growing day by day. However, the polymers mechanical properties are strain-rate dependent due to their viscoelastic nature. Especially for natural fibre reinforced polymer composites (NFPCs) which the involvement of filler has caused rather complex failure mechanisms under different strain rates. Moreover, some uneven micro-sized natural fibres such as bagasse, coir and wood were found often resulting in micro-cracks and voids formation in composites. This paper provides an overview of recent research on the mechanical properties of NFPCs under various loading conditions-different form (tensile, compression, bending) and different strain rates. The literature on characterisation techniques toward different strain rates, composite failure behaviours and current challenges are summarised which have led to the notion of future study trend. The strength of NFPCs is generally found grow proportionally with the strain rate up to a certain degree depending on the fibre-matrix stress-transfer efficiency. The failure modes such as embrittlement and fibre-matrix debonding were often encountered at higher strain rates. The natural filler properties, amount, sizes and polymer matrix types are found to be few key factors affecting the performances of composites under various strain rates whereby optimally adjust these factors could maximise the fibre-matrix stress-transfer efficiency and led to performance increases under various loading strain rates.

scholarly journals Static Mechanical Properties of Expanded Polypropylene Crushable Foam

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 249
Author(s):  
Przemysław Rumianek ◽  
Tomasz Dobosz ◽  
Radosław Nowak ◽  
Piotr Dziewit ◽  
Andrzej Aromiński
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Strain Rate ◽  
Energy Absorption ◽  
Experimental Tests ◽  
Absorption Capacity ◽  
Strain Rates ◽  
Foam Density ◽  
Energy Absorption Capacity ◽  
Closed Cell

Closed-cell expanded polypropylene (EPP) foam is commonly used in car bumpers for the purpose of absorbing energy impacts. Characterization of the foam’s mechanical properties at varying strain rates is essential for selecting the proper material used as a protective structure in dynamic loading application. The aim of the study was to investigate the influence of loading strain rate, material density, and microstructure on compressive strength and energy absorption capacity for closed-cell polymeric foams. We performed quasi-static compressive strength tests with strain rates in the range of 0.2 to 25 mm/s, using a hydraulically controlled material testing system (MTS) for different foam densities in the range 20 g/dm3 to 220 g/dm3. The above tests were carried out as numerical simulation using ABAQUS software. The verification of the properties was carried out on the basis of experimental tests and simulations performed using the finite element method. The method of modelling the structure of the tested sample has an impact on the stress values. Experimental tests were performed for various loads and at various initial temperatures of the tested sample. We found that increasing both the strain rate of loading and foam density raised the compressive strength and energy absorption capacity. Increasing the ambient and tested sample temperature caused a decrease in compressive strength and energy absorption capacity. For the same foam density, differences in foam microstructures were causing differences in strength and energy absorption capacity when testing at the same loading strain rate. To sum up, tuning the microstructure of foams could be used to acquire desired global materials properties. Precise material description extends the possibility of using EPP foams in various applications.

scholarly journals New Approach In The Properties Evaluation Of Ultrafine-Grained OFHC Copper

2015 ◽  
Vol 60 (2) ◽  
pp. 605-614 ◽  
Author(s):  
T. Kvačkaj ◽  
A. Kováčová ◽  
J. Bidulská ◽  
R. Bidulský ◽  
R. Kočičko
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Tensile Tests ◽  
Coarse Grained ◽  
Wear Behaviour ◽  
Ofhc Copper ◽  
Strain Rates ◽  
Ultrafine Grained ◽  
Reduction Of Area ◽  
Pin On Disk

AbstractIn this study, static, dynamic and tribological properties of ultrafine-grained (UFG) oxygen-free high thermal conductivity (OFHC) copper were investigated in detail. In order to evaluate the mechanical behaviour at different strain rates, OFHC copper was tested using two devices resulting in static and dynamic regimes. Moreover, the copper was subjected to two different processing methods, which made possible to study the influence of structure. The study of strain rate and microstructure was focused on progress in the mechanical properties after tensile tests. It was found that the strain rate is an important parameter affecting mechanical properties of copper. The ultimate tensile strength increased with the strain rate increasing and this effect was more visible at high strain rates$({\dot \varepsilon} \sim 10^2 \;{\rm{s}}^{ - 1} )$. However, the reduction of area had a different progress depending on microstructural features of materials (coarse-grained vs. ultrafine-grained structure) and introduced strain rate conditions during plastic deformation (static vs. dynamic regime). The wear behaviour of copper was investigated through pin-on-disk tests. The wear tracks examination showed that the delamination and the mild oxidational wears are the main wear mechanisms.

Local Investigations of the Mechanical Properties of Ultrafine Grained Metals by Nanoindentations

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
Rate Sensitivity ◽  
Strain Rates ◽  
Fcc Metals ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Indentation Strain

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.

Impact tensile behavior and frequency response of 3D braided composites

2011 ◽  
Vol 82 (3) ◽  
pp. 280-287 ◽  
Author(s):  
Xuehui Gan ◽  
Jianhua Yan ◽  
Bohong Gu ◽  
Baozhong Sun
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Tensile Properties ◽  
High Strain ◽  
Tensile Modulus ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Braided Composites ◽  
3D Braided Composites

The uniaxial tensile properties of 4-step 3D braided E-glass/epoxy composites under quasi-static and high-strain rate loadings have been investigated to evaluate the tensile failure mode at different strain rates. The uniaxial tensile properties at high strain rates from 800/s to 2100/s were tested using the split Hopkinson tension bar (SHTB) technique. The tensile properties at quasi-static strain rate were also tested and compared with those in high strain rates. Z-transform theory is applied to 3D braided composites to characterize the system dynamic behaviors in frequency domain. The frequency responses and the stability of 3D braided composites under quasi-static and high-strain rate compression have been analyzed and discussed in the Z-transform domain. The results indicate that the stress-strain curves are rate sensitive, and tensile modulus, maximum tensile stress and corresponding tensile strain are also sensitive to the strain rate. The tensile modulus, maximum tensile stress of the 3D braided composites are linearly increased with the strain rate. With increasing of the strain rate (from 0.001/s to 2100/s), the tensile failure of the 3D braided composite specimens has a tendency of transition from ductile failure to brittle failure. The magnitude response and phase response is very different in quasi-static loading with that in high-strain rate loading. The 3D braided composite system is more stable at high strain rate than quasi-static loading.

Viscoplastic Constitutive Model for High Strain Rate Mechanical Properties of SAC-Q Leadfree Solder After High-Temperature Prolonged Storage

2018 ◽  
Author(s):  
Pradeep Lall ◽  
Vikas Yadav ◽  
Jeff Suhling ◽  
David Locker
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Strain Rate ◽  
Strain Rate ◽  
Thermal Aging ◽  
High Strain ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Aging Effects ◽  
Model Predictions

Electronics in automotive underhood and downhole drilling applications may be subjected to sustained operation at high temperature in addition to high strain-rate loads. SAC solders used for second level interconnects have been shown to experience degradation in high strain-rate mechanical properties under sustained exposure to high temperatures. Industry search for solutions for resisting the high-temperature degradation of SAC solders has focused on the addition of dopants to the alloy. In this study, a doped SAC solder called SAC-Q solder have been studied. The high strain rate mechanical properties of SAC-Q solder have been studied under elevated temperatures up to 200°C. Samples with thermal aging at 50°C for up to 6-months have been used for measurements in uniaxial tensile tests. Measurements for SAC-Q have been compared to SAC105 and SAC305 for identical test conditions and sample geometry. Data from the SAC-Q measurements has been fit to the Anand Viscoplasticity model. In order to assess the predictive power of the model, the computed Anand parameters have been used to simulate the uniaxial tensile test and the model predictions compared with experimental data. Model predictions show good correlation with experimental measurements. The presented approach extends the Anand Model to include thermal aging effects.

Anisotropic Behavior of Aluminum Alloy 2024-Graphene Composites at Varying Strain Rates

2017 ◽  
Author(s):  
M. Anthony Xavior ◽  
Prashantha Kumar Hosamane ◽  
Jeyapandiarajan Paulchamy
Keyword(s):  
Aspect Ratio ◽  
Strain Rate ◽  
Ball Milling ◽  
High Strength ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Strain Sensitivity ◽  
Anisotropic Behavior ◽  
Dimple Size ◽  
Processing Methods

In fabrication of high strength materials coupled with improved mechanical properties; focus on integration of multifunctional reinforcements are increasing along with novel processing methods. Single layer 2-D material Graphene are among one such novel material with huge aspect ratio, posse’s high strength. But the real challenge is processing and incorporation of these reinforcements with appropriate content in metals or its alloys matrix. Current research work focus to study the anisotropic behavior on addition of pristine Graphene/MWCNT and processing methods like ball milling under constant ball to powder precursor ratio (BPR) of AA 2024 nanocomposites. The extent change in aspect ratio, size of the nanoparticle mixtures during ball milling were analyzed under SEM and Raman spectroscopy. Thus obtained (ball milled) precursors are consolidated through vacuum hot press and hot extruded to get typical flat specimen at optimized processing parameters. XRD analysis, relative density and hardness measurement is done on extruded composites. Thus developed composites are subjected to study the anisotropic behavior at various orientations and strain rates (0.5, 1.0, 1.5 mm/min) using uniaxial tensile testing instrument and corresponding stress strains graphs were obtained. The fracture surfaces were characterized by scanning electron microscope (SEM) and its shows the nucleation of the dimple size are varies with increasing the strain rate and also deeper dimple size were noticed. Negative strain sensitivity were observed for the lower strain rate (0.1 and 0.3 mm/min) and positive strain sensitivity for higher strain rates. Microstructural anisotropy infers that AA2024-Graphene/MWCNT composites are sensitive to strain rate and shear type of failure is observed on increasing the strain rate.

scholarly journals Strain-Rate-Dependent Deformation Behavior and Mechanical Properties of a Multi-Phase Medium-Manganese Steel

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 344 ◽  
Author(s):  
Simon Sevsek ◽  
Christian Haase ◽  
Wolfgang Bleck
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Deformation Behavior ◽  
Rate Sensitivity ◽  
Manganese Steel ◽  
Strain Rates ◽  
Rate Dependent ◽  
Medium Manganese Steel ◽  
Multi Phase

The strain-rate-dependent deformation behavior of an intercritically annealed X6MnAl12-3 medium-manganese steel was analyzed with respect to the mechanical properties, activation of deformation-induced martensitic phase transformation, and strain localization behavior. Intercritical annealing at 675 °C for 2 h led to an ultrafine-grained multi-phase microstructure with 45% of mostly equiaxed, recrystallized austenite and 55% ferrite or recovered, lamellar martensite. In-situ digital image correlation methods during tensile tests revealed strain localization behavior during the discontinuous elastic-plastic transition, which was due to the localization of strain in the softer austenite in the early stages of plastic deformation. The dependence of the macroscopic mechanical properties on the strain rate is due to the strain-rate sensitivity of the microscopic deformation behavior. On the one hand, the deformation-induced phase transformation of austenite to martensite showed a clear strain-rate dependency and was partially suppressed at very low and very high strain rates. On the other hand, the strain-rate-dependent relative strength of ferrite and martensite compared to austenite influenced the strain partitioning during plastic deformation, and subsequently, the work-hardening rate. As a result, the tested X6MnAl12-3 medium-manganese steel showed a negative strain-rate sensitivity at very low to medium strain rates and a positive strain-rate sensitivity at medium to high strain rates.

scholarly journals Mechanical behaviour and structure of snow under uniaxial tensile stress

1980 ◽  
Vol 26 (94) ◽  
pp. 275-282 ◽  
Author(s):  
Hidek Narita
Keyword(s):  
Tensile Stress ◽  
Strain Rate ◽  
Mechanical Behaviour ◽  
Maximum Strength ◽  
Ductile Deformation ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Thin Sections ◽  
Uniaxial Tensile Stress ◽  
Small Cracks

AbstractThe mechanical behaviour of snow was studied at — 10°C under uniaxial tensile stress in a range of cross-head speed 6.8 × 10–8to 3.1 × 10–4ms–1and snow density 240-470 kg m–3.It was found from the resisting force-deformation curves that the snow was deformed in two different ways: namely, brittle and ductile deformation at high and low strain-rates, respectively. The critical strain-rate dividing the two deformation modes was found to depend on the density of snow. In ductile deformation, many small cracks appeared throughout the entire specimen. Their features were observed by making thin sections and they were compared with small cracks formed in natural snow on a mountain slope.The maximum strength of snow was found to depend on strain-rate: at strain-rates above about 10–5s–1, the maximum strength increased with decreasing strain-rate but below 10–5s–1it decreased with decreasing strain-rate.

Sign in / Sign up

Export Citation Format

Share Document