DESIGN OF WIDEBAND LTE POWER AMPLIFIER WITH NOVEL DUAL STAGE LINEARIZER FOR MOBILE WIRELESS COMMUNICATION

2014 ◽  
Vol 23 (08) ◽  
pp. 1450111 ◽  
Author(s):  
U. ESWARAN ◽  
H. RAMIAH ◽  
J. KANESAN ◽  
A. W. REZA
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Supply Voltage ◽  
Path Loss ◽  
Stringent Requirement ◽  
Fully Integrated ◽  
Power Added Efficiency ◽  
Channel Bandwidth ◽  
Dual Stage

In this paper, a 1 mm × 1 mm fully integrated wideband dual-stage power amplifier (PA) for long-term evolution (LTE) band 1 (1920–1980 MHz) is presented. Fabricated in a 2 μm InGaP/GaAs hetero-junction bipolar transistor (HBT) process, the operating gain is observed to be 31.3 dB. The PA meets the minimum adjacent channel leakage ratio (ACLR) requirement of -30 dBc for LTE with 20 MHz wide channel bandwidth up to an output power of 30 dBm with the aid of a novel dual stage linearizer. Biased at low quiescent current of less than 100 mA with a headroom consumption of 3.5 V, the power added efficiency (PAE) is observed to be 38.29% at 30 dBm. With this high linear output power, the stringent requirement of antenna path loss is nullified. PA serves to be the first reported work to achieve 30 dBm linear output power at supply voltage of 3.5 V.

A broadband 23.1 ∼ 27.2 GHz doherty power amplifier with peak output power of 24.3 dBm

Circuit World ◽  
2019 ◽  
Vol 46 (1) ◽  
pp. 1-5
Author(s):  
Yanfeng Fang ◽  
Yijiang Zhang
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Input Power ◽  
Content Type ◽  
Fully Integrated ◽  
Power Added Efficiency ◽  
Peak Output Power ◽  
Saturated Output Power ◽  
Direct Input ◽  
Matching Techniques

Purpose This paper aims to implement a new high output power fully integrated 23.1 to 27.2 GHz gallium arsenide heterojunction bipolar transistor power amplifier (PA) to meet the stringent linearity requirements of LTE systems. Design/methodology/approach The direct input power dividing technique is used on the chip. Broadband input and output matching techniques are used for broadband Doherty operation. Findings The PA achieves a small-signal gain of 22.8 dB at 25.1 GHz and a saturated output power of 24.3 dBm at 25.1 GHz with a maximum power added efficiency of 31.7%. The PA occupies 1.56 mm2 (including pads) and consumes a maximum current of 79.91 mA from a 9 V supply. Originality/value In this paper, the author proposed a novel direct input dividing technique with broadband matching circuits using a low Q output matching technique, and demonstrated a fully-integrated Doherty PA across frequencies of 23.1∼27.2 GHz for long term evolution-license auxiliary access (LTE-LAA) handset applications.

A 5.2/5.8 GHz Dual Band On-Off Keying Transmitter Design for Bio-Signal Transmission

2018 ◽  
Vol 3 (2) ◽  
Author(s):  
Chang-Hsi Wu ◽  
Hong-Cheng You ◽  
Shun-Zhao Huang
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Power Efficiency ◽  
Supply Voltage ◽  
Maximum Output Power ◽  
Dual Band ◽  
Maximum Output ◽  
Power Combiner ◽  
Power Added Efficiency ◽  
Chip Size

Abstract An architecture of 5.2/5.8-GHz dual-band on-off keying (DBOOK) modulated transmitter is designed in a 0.18-μm CMOS technology. The proposed DBOOK transmitter is used in the biosignal transmission system with high power efficiency and small area. To reduce power consumption and enhance output swing, two pairs of center-tapped transformers are used as both LC tank and source grounding choke for the designed voltage controlled oscillator (VCO). Switching capacitances are used to achieve dual band operations, and a complemented power combiner is used to merge the differential output power of VCO to a single-ended output. Besides, the linearizer circuits are used in the proposed power amplifier with wideband output matching to improve the linearity both at 5.2/5.8-GHz bands. The designed DBOOK transmitter is implemented by dividing it into two chips. One chip implements the dual-band switching VCO and power combiner, and the other chip implements a linear power amplifier including dual-band operation. The first chip drives an output power of 2.2mW with consuming power of 5.13 mW from 1.1 V supply voltage. With the chip size including pad of 0.61 × 0.91 m2, the measured data rate and transmission efficiency attained are 100 Mb/s and 51 pJ/bit, respectively. The second chip, for power enhanced mode, exhibits P1 dB of −9 dBm, IIP3 of 1 dBm, the output power 1 dB compression point of 12.42 dBm, OIP3 of about 21 dBm, maximum output power of 17.02/16.18 dBm, and power added efficiency of 17.13/16.95% for 5.2/ 5.8 GHz. The chip size including pads is 0:693 × 1:084mm2.

scholarly journals A Fully Integrated Compact Outphasing CMOS Power Amplifier Using a Parallel-Combining Transformer with a Tuning Inductor Method

Electronics ◽  
2020 ◽  
Vol 9 (2) ◽  
pp. 257 ◽  
Author(s):  
Se-Eun Choi ◽  
Hyunjin Ahn ◽  
Joonhoi Hur ◽  
Kwan-Woo Kim ◽  
Ilku Nam ◽  
...  
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Cmos Process ◽  
Power Combining ◽  
Fully Integrated ◽  
Term Evolution ◽  
Class D ◽  
Adjacent Channel ◽  
On Chip

This work presents a compact on-chip outphasing power amplifier with a parallel-combining transformer (PCT). A series-combining transformer (SCT) and PCT are analyzed as power-combining transformers for outphasing operations. Compared to the SCT, which is typically used for on-chip outphasing combiners, the PCT is much smaller. The outphasing operations of the transformer combiners and class-D switching PAs are also analyzed. A tuning inductor method is proposed to improve the efficiency of class-D power amplifiers (PAs) with power-combining transformers in the out-of-phase mode. The proposed PA was implemented with a standard 0.18 µm CMOS process. The measured maximum drain efficiency is 37.3% with an output power of 22.4 dBm at 1.7 GHz. A measured adjacent channel leakage ratio (ACLR) of less than −30 dBc is obtained for a long-term evolution (LTE) signal with a bandwidth of 10 MHz.

scholarly journals Analysis and Compensation of the AM-AM and AM-PM Distortion for CMOS Cascode Class-E Power Amplifier

2009 ◽  
Vol 2009 ◽  
pp. 1-9 ◽  
Author(s):  
Wen An Tsou ◽  
Wen Shen Wuen ◽  
Tzu Yi Yang ◽  
Kuei Ann Wen
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Signal Source ◽  
Nonlinear Capacitance ◽  
Power Added Efficiency ◽  
Equivalent Impedance ◽  
Common Gate ◽  
Class E

Analysis and compensation methodology of the AM-AM and AM-PM distortion of cascode class-E power amplifiers are presented. A physical-based model is proposed to illustrate that the nonlinear capacitance and transconductance cause the AM-AM and AM-PM distortion when modulating the supply voltage of the PA. A novel methodology that can reduce the distortion is also proposed. By degenerating common-gate transistor into a resistor, the constant equivalent impedance is obtained so that the AM-AM and AM-PM distortion is compensated. An experimental prototype of 2.6 GHz cascode class-E power amplifier with the AM-AM and AM-PM compensation has been integrated in a 0.18 μm CMOS technology, occupies a total die area of 1.6 mm2. It achieves a drain efficiency of 17.8% and a power-added efficiency of 16.6% while delivering 12 dBm of linear output power and drawing 31 mA from a 1.8 V supply. Finally, a co-simulation result demonstrated that, when the distortion of the PA has been compensated, the EVM is improved from −17 dB to −19 dB with an IEEE802.11a-like signal source.

scholarly journals A 28GHz Power Amplifier with Analog Predistortion Linearizer in 65nm CMOS

2021 ◽  
Vol 5 (2) ◽  
pp. 5-10
Author(s):  
He Peng ◽  
Yuqing Dou
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Supply Voltage ◽  
Linearization Method ◽  
Cmos Process ◽  
Power Added Efficiency ◽  
Saturated Output Power ◽  
Gain Compensation ◽  
Predistortion Linearization ◽  
Frequency Power

This paper proposes that a radio frequency power amplifier is suitable for a 5G millimeter wave. It adopts a three-stage single-ended structure at 28GHz. An analog predistortion linearization method is used to improve the linearity of the power amplifier (PA). As a result, there is a significant improvement in power-added efficiency (PAE) and linearity is achieved. The Ka-band PA is implemented in TSMC 65nm CMOS process. At 1.2V supply voltage, the PA proposed in this paper achieves a saturated output power of 15.9dBm and a PAE of 16%. After linearization, the output power at the 1dB compression point is increased by 2dBm, with efficient gain compensation performance.

scholarly journals K-Band Hetero-Stacked Differential Cascode Power Amplifier with High Psat and Efficiency in 65 nm LP CMOS Technology

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 890
Author(s):  
Kyu-Jin Choi ◽  
Jae-Hyun Park ◽  
Seong-Kyun Kim ◽  
Byung-Sung Kim
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Oxide Semiconductor ◽  
Common Source ◽  
Output Resistance ◽  
Power Added Efficiency ◽  
High Output ◽  
K Band

A K-band complementary metal-oxide-semiconductor (CMOS) differential cascode power amplifier is designed with the thin-oxide field effect transistor (FET) common source (CS) stage and thick-oxide FET common gate (CG) stage. Use of the thick-oxide CG stage affords the high supply voltage to 3.7 V and enables the high output power. Additionally, simple analysis shows that the gain degradation due to the low cut-off frequency of the thick-oxide CG FET can be compensated by the high output resistance of the thick-oxide FET if the inter-stage node is neutralized. The measured results of the proposed power amplifier demonstrate the saturated output power of the 23.3 dBm with the 31.3% peak power added efficiency (PAE) at 24 GHz frequency. The chip is fabricated in 65-nm low power (LP) CMOS technology and the chip size including all pads is 700 μm × 630 μm.

Fully-integrated GaAs HBT power amplifier MMIC with high linear output power for 3 GHz-band broadband wireless applications

2006 ◽  
Vol 42 (22) ◽  
pp. 1286 ◽  
Author(s):  
M. Hirata ◽  
T. Oka ◽  
M. Hasegawa ◽  
Y. Amano ◽  
Y. Ishimaru ◽  
...  
Keyword(s):  
Output Power ◽  
Power Amplifier ◽  
Broadband Wireless ◽  
Fully Integrated ◽  
Wireless Applications

scholarly journals Design of W-Band GaN-on-Silicon Power Amplifier Using Low Impedance Lines

2021 ◽  
Vol 11 (19) ◽  
pp. 9017
Author(s):  
Jinho Jeong ◽  
Yeongmin Jang ◽  
Jongyoun Kim ◽  
Sosu Kim ◽  
Wansik Kim
Keyword(s):  
Power Density ◽  
Output Power ◽  
Power Amplifier ◽  
High Power ◽  
Common Source ◽  
High Electron ◽  
Large Signal ◽  
Power Added Efficiency ◽  
W Band ◽  
Gan On Si

In this paper, a high-power amplifier integrated circuit (IC) in gallium-nitride (GaN) on silicon (Si) technology is presented at a W-band (75–110 GHz). In order to mitigate the losses caused by relatively high loss tangent of Si substrate compared to silicon carbide (SiC), low-impedance microstrip lines (20–30 Ω) are adopted in the impedance matching networks. They allow for the impedance transformation between 50 Ω and very low impedances of the wide-gate transistors used for high power generation. Each stage is matched to produce enough power to drive the next stage. A Lange coupler is employed to combine two three-stage common source amplifiers, providing high output power and good input/output return loss. The designed power amplifier IC was fabricated in the commercially available 60 nm GaN-on-Si high electron mobility transistor (HEMT) foundry. From on-wafer probe measurements, it exhibits the output power higher than 26.5 dBm and power added efficiency (PAE) higher than 8.5% from 88 to 93 GHz with a large-signal gain > 10.5 dB. Peak output power is measured to be 28.9 dBm with a PAE of 13.3% and a gain of 9.9 dB at 90 GHz, which corresponds to the power density of 1.94 W/mm. To the best of the authors’ knowledge, this result belongs to the highest output power and power density among the reported power amplifier ICs in GaN-on-Si HEMT technologies operating at the W-band.

A fully matched dual stage CMOS power amplifier with integrated passive linearizer attaining 23 db gain, 40% PAE and 28 DBM OIP3

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Premmilaah Gunasegaran ◽  
Jagadheswaran Rajendran ◽  
Selvakumar Mariappan ◽  
Yusman Mohd Yusof ◽  
Zulfiqar Ali Abdul Aziz ◽  
...  
Keyword(s):  
Power Consumption ◽  
Output Power ◽  
Power Amplifier ◽  
Maximum Output Power ◽  
Maximum Output ◽  
Power Gain ◽  
Matching Network ◽  
Content Type ◽  
Power Added Efficiency ◽  
Main Amplifier

Purpose The purpose of this paper is to introduce a new linearization technique known as the passive linearizer technique which does not affect the power added efficiency (PAE) while maintaining a power gain of more than 20 dB for complementary metal oxide semiconductor (CMOS) power amplifier (PA). Design/methodology/approach The linearization mechanism is executed with an aid of a passive linearizer implemented at the gate of the main amplifier to minimize the effect of Cgs capacitance through the generation of opposite phase response at the main amplifier. The inductor-less output matching network presents an almost lossless output matching network which contributes to high gain, PAE and output power. The linearity performance is improved without the penalty of power consumption, power gain and stability. Findings With this topology, the PA delivers more than 20 dB gain for the Bluetooth Low Energy (BLE) Band from 2.4 GHz to 2.5 GHz with a supply headroom of 1.8 V. At the center frequency of 2.45 GHz, the PA exhibits a gain of 23.3 dB with corresponding peak PAE of 40.11% at a maximum output power of 14.3 dBm. At a maximum linear output power of 12.7 dBm, a PAE of 37.3% has been achieved with a peak third order intermodulation product of 28.04 dBm with a power consumption of 50.58 mW. This corresponds to ACLR of – 20 dBc, thus qualifying the PA to operate for BLE operation. Practical implications The proposed technique is able to boost up the efficiency and output power, as well as linearize the PA closer to 1 dB compression point. This reduces the trade-off between linear output power and PAE in CMOS PA design. Originality/value The proposed CMOS PA can be integrated comfortably to a BLE transmitter, allowing it to reduce the transceiver’s overall power consumption.

scholarly journals A 2.5-GHz 1-V High Efficiency CMOS Power Amplifier IC with a Dual-Switching Transistor and Third Harmonic Tuning Technique

Electronics ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 69 ◽  
Author(s):  
Taufiq Alif Kurniawan ◽  
Toshihiko Yoshimasu
Keyword(s):  
Power Amplifier ◽  
High Efficiency ◽  
Low Voltage ◽  
Supply Voltage ◽  
Drain Current ◽  
Cmos Technology ◽  
Back Gate ◽  
Third Harmonic ◽  
Power Added Efficiency ◽  
Switching Transistor

This paper presents a 2.5-GHz low-voltage, high-efficiency CMOS power amplifier (PA) IC in 0.18-µm CMOS technology. The combination of a dual-switching transistor (DST) and a third harmonic tuning technique is proposed. The DST effectively improves the gain at the saturation power region when the additional gain extension of the secondary switching transistor compensates for the gain compression of the primary one. To achieve high-efficiency performance, the third harmonic tuning circuit is connected in parallel to the output load. Therefore, the flattened drain current and voltage waveforms are generated, which in turn reduce the overlapping and the dc power consumption significantly. In addition, a 0.5-V back-gate voltage is applied to the primary switching transistor to realize the low-voltage operation. At 1 V of supply voltage, the proposed PA has achieved a power added efficiency (PAE) of 34.5% and a saturated output power of 10.1 dBm.

Sign in / Sign up

Export Citation Format

Share Document