Design of Low Leakage PVT Variations Aware CMOS Bootstrapped Driver Circuit

2017 ◽  
Vol 26 (09) ◽  
pp. 1750137 ◽  
Author(s):  
Vijay Kumar Sharma
Keyword(s):  
Large Scale ◽  
Low Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Monte Carlo Analysis ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Switching Speed ◽  
Low Leakage ◽  
Driver Circuit ◽  
Pvt Variations

This paper describes a novel complementary metal oxide semiconductor (CMOS) bootstrapped driver circuit for driving large resistive capacitive (RC) loads. The proposed bootstrapped driver reduces the leakage as well as process, voltage and temperature (PVT) variations from the boosted nodes with higher switching speed. Very large scale integration (VLSI) designers need boosted output for the logic circuits which are operating in ultra-deep submicron regime under widespread use of low voltage. Proposed CMOS bootstrapped driver circuit is easy in design; built with minimum number of transistors and have high boosting efficiency with sharp output performance. Comparative evaluations with existing bootstrapped driver circuits are reported. Simulation results are derived by HSPICE tool with predictive technology model (PTM) bulk CMOS process fabrication at 32 nm technology node. The ability of large leakage reduction makes this driver superior as compared to active drivers. An average of 96.97% leakage current is saved at nominal ultra-low voltage of 0.15 V. Monte-Carlo analysis indicates that the proposed bootstrapped driver has less sensitivity of PVT variations. The power consumption and delay sensitivities are reduced by 10 × and 4.12 × as compared to conventional circuit.

scholarly journals A Smart Floating Gate Transistor with Two Control Gates for Active Noise Control

Micromachines ◽  
2019 ◽  
Vol 10 (11) ◽  
pp. 722
Author(s):  
Mao ◽  
Yang ◽  
Ma ◽  
Yan ◽  
Zhang
Keyword(s):  
Large Scale ◽  
Noise Control ◽  
Low Cost ◽  
Active Noise Control ◽  
Complementary Metal Oxide Semiconductor ◽  
Floating Gate ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Active Noise ◽  
Floating Gate Transistor

A smart floating gate transistor with two control gates was proposed for active noise control in bioelectrical signal measurement. The device, which is low cost and capable of large-scale integration, was implemented in a standard single-poly complementary metal–oxide–semiconductor (CMOS) process. A model of the device was developed to demonstrate the working principle. Theoretical analysis and simulation results proved the superposition of the two control gates. A series of test experiments were carried out and the results showed that the device was in accordance with the basic electrical characteristics of a floating gate transistor, including the current–voltage (I–V) characteristics and the threshold characteristics observed on the two control gates. Based on the source follower circuit, the experimental results proved that the device can reduce interference by more than 29 dB, which demonstrates the feasibility of the proposed device for active noise control.

Realization of Fractional-Order Double-Scroll Chaotic System Using Operational Transconductance Amplifier (OTA)

2017 ◽  
Vol 27 (01) ◽  
pp. 1850006 ◽  
Author(s):  
Mohammad Rafiq Dar ◽  
Nasir Ali Kant ◽  
Farooq Ahmad Khanday
Keyword(s):  
Fractional Order ◽  
Chaotic System ◽  
Low Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Operational Transconductance Amplifiers ◽  
System A ◽  
Transconductance Amplifier ◽  
Theoretical Predictions

Realization of fractional-order double-scroll chaotic system using Operational Transconductance Amplifiers (OTAs) as active elements are presented in this paper. The fractional-order double-scroll chaotic system has been studied before as well using passive RC-ladder and tree-based structures but in this paper the requisite fractional-order integration has been accomplished through an integer-order multiple-feedback topology. As compared to double or multiple scroll chaotic systems existing in the open literature, the proposed realization offers the advantages of (a) low-voltage implementation, (b) integrablity as the design is resistor- and inductor-less and only grounded components have been employed in the design, and, (c) electronic tunability of the fractional order, time-constants and gain factors. In order to demonstrate the usefulness of the chaotic system, a simple secure message communication system has been designed and verified for its operation. The theoretical predictions of the proposed implementations have been verified by using 0.35[Formula: see text][Formula: see text]m complementary metal oxide semiconductor (CMOS) process file provided by Austrian Micro System (AMS).

Output Voltage Sampling Circuit for Discontinuous Conduction Mode Flyback Pulse-Width Modulation Controller

2016 ◽  
Vol 25 (11) ◽  
pp. 1650140 ◽  
Author(s):  
Ling-Feng Shi ◽  
Zhen-Bo Shi ◽  
Sen Chen ◽  
Jian-Hui Xun
Keyword(s):  
Pulse Width ◽  
Output Voltage ◽  
Pulse Width Modulation ◽  
Low Voltage ◽  
Low Cost ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Discharge Time ◽  
Constant Output

Primary-side controlled pulse-width modulation (PWM) flyback converter has been widely used in low-power and low-voltage products for its simple structure and low cost. This paper presents a novel output voltage sampling circuit which considers the influence of the rectifier diode current on the output voltage sampling. The output voltage sampling circuit samples the output voltage at 85% of the secondary inductance discharge time [Formula: see text] of last cycle, which improves the accuracy of the output voltage sampling circuit. Besides, the circuit can also sample the secondary inductance discharge time [Formula: see text]. Finally, a chip has been fabricated in 0.6[Formula: see text][Formula: see text]m complementary metal-oxide semiconductor (CMOS) process, which is used in the presented output voltage sampling circuit in its internal circuit to simple output voltage and achieve constant output voltage.

scholarly journals A Low-Power Spiking Neural Network Chip Based on a Compact LIF Neuron and Binary Exponential Charge Injector Synapse Circuits

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4462
Author(s):  
Malik Summair Asghar ◽  
Saad Arslan ◽  
HyungWon Kim
Keyword(s):  
Neural Network ◽  
Power Consumption ◽  
Large Scale ◽  
Average Power ◽  
Complementary Metal Oxide Semiconductor ◽  
Input Image ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Spiking Neural Network ◽  
Digital Implementation

To realize a large-scale Spiking Neural Network (SNN) on hardware for mobile applications, area and power optimized electronic circuit design is critical. In this work, an area and power optimized hardware implementation of a large-scale SNN for real time IoT applications is presented. The analog Complementary Metal Oxide Semiconductor (CMOS) implementation incorporates neuron and synaptic circuits optimized for area and power consumption. The asynchronous neuronal circuits implemented benefit from higher energy efficiency and higher sensitivity. The proposed synapse circuit based on Binary Exponential Charge Injector (BECI) saves area and power consumption, and provides design scalability for higher resolutions. The SNN model implemented is optimized for 9 × 9 pixel input image and minimum bit-width weights that can satisfy target accuracy, occupies less area and power consumption. Moreover, the spiking neural network is replicated in full digital implementation for area and power comparisons. The SNN chip integrated from neuron and synapse circuits is capable of pattern recognition. The proposed SNN chip is fabricated using 180 nm CMOS process, which occupies a 3.6 mm2 chip core area, and achieves a classification accuracy of 94.66% for the MNIST dataset. The proposed SNN chip consumes an average power of 1.06 mW—20 times lower than the digital implementation.

scholarly journals Monolithically-Integrated Single-Photon Avalanche Diode in a Zero-Change Standard CMOS Process for Low-Cost and Low-Voltage LiDAR Application

Instruments ◽  
2019 ◽  
Vol 3 (2) ◽  
pp. 33
Author(s):  
Jinsoo Rhim ◽  
Xiaoge Zeng ◽  
Zhihong Huang ◽  
Sai Rahul Chalamalasetti ◽  
Marco Fiorentino ◽  
...  
Keyword(s):  
Low Voltage ◽  
Single Photon ◽  
Low Cost ◽  
Minimum Cost ◽  
Complementary Metal Oxide Semiconductor ◽  
Complete Characterization ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Avalanche Diode ◽  
Monolithically Integrated

We present a single-photon sensor based on the single-photon avalanche diode (SPAD) that is suitable for low-cost and low-voltage light detection and ranging (LiDAR) applications. It is implemented in a zero-change standard 0.18-μm complementary metal oxide semiconductor process at the minimum cost by excluding any additional processing step for customized doping profiles. The SPAD is based on circular shaped P+/N-well junction of 8-μm diameter, and it achieves low breakdown voltage below 10 V so that the operation voltage of the single-photon sensor can be minimized. The quenching and reset circuit is integrated monolithically to capture photon-generated output pulses for measurement. A complete characterization of our single-photon sensor is provided.

scholarly journals Phase Change Metasurfaces by Continuous or Quasi-Continuous Atoms for Active Optoelectronic Integration

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1272
Author(s):  
Zhihua Fan ◽  
Qinling Deng ◽  
Xiaoyu Ma ◽  
Shaolin Zhou
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Complementary Metal Oxide Semiconductor ◽  
Photonic Devices ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Nanophotonic Devices ◽  
Optoelectronic Integration ◽  
Hybrid Devices ◽  
Micro Electromechanical System

In recent decades, metasurfaces have emerged as an exotic and appealing group of nanophotonic devices for versatile wave regulation with deep subwavelength thickness facilitating compact integration. However, the ability to dynamically control the wave–matter interaction with external stimulus is highly desirable especially in such scenarios as integrated photonics and optoelectronics, since their performance in amplitude and phase control settle down once manufactured. Currently, available routes to construct active photonic devices include micro-electromechanical system (MEMS), semiconductors, liquid crystal, and phase change materials (PCMs)-integrated hybrid devices, etc. For the sake of compact integration and good compatibility with the mainstream complementary metal oxide semiconductor (CMOS) process for nanofabrication and device integration, the PCMs-based scheme stands out as a viable and promising candidate. Therefore, this review focuses on recent progresses on phase change metasurfaces with dynamic wave control (amplitude and phase or wavefront), and especially outlines those with continuous or quasi-continuous atoms in favor of optoelectronic integration.

scholarly journals Universal Filter Based on Compact CMOS Structure of VDDDA

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1683
Author(s):  
Winai Jaikla ◽  
Fabian Khateb ◽  
Tomasz Kulej ◽  
Koson Pitaksuttayaprot
Keyword(s):  
Metal Oxide ◽  
Dynamic Range ◽  
Complementary Metal Oxide Semiconductor ◽  
Metal Oxide Semiconductor ◽  
Experimental Results ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Voltage Gain ◽  
Universal Filter ◽  
Mos Transistor

This paper proposes the simulated and experimental results of a universal filter using the voltage differencing differential difference amplifier (VDDDA). Unlike the previous complementary metal oxide semiconductor (CMOS) structures of VDDDA that is present in the literature, the present one is compact and simple, owing to the employment of the multiple-input metal oxide semiconductor (MOS) transistor technique. The presented filter employs two VDDDAs, one resistor and two grounded capacitors, and it offers low-pass: LP, band-pass: BP, band-reject: BR, high-pass: HP and all-pass: AP responses with a unity passband voltage gain. The proposed universal voltage mode filter has high input impedances and low output impedance. The natural frequency and bandwidth are orthogonally controlled by using separated transconductance without affecting the passband voltage gain. For a BP filter, the root mean square (RMS) of the equivalent output noise is 46 µV, and the third intermodulation distortion (IMD3) is −49.5 dB for an input signal with a peak-to peak of 600 mV, which results in a dynamic range (DR) of 73.2 dB. The filter was designed and simulated in the Cadence environment using a 0.18-µm CMOS process from Taiwan semiconductor manufacturing company (TSMC). In addition, the experimental results were obtained by using the available commercial components LM13700 and AD830. The simulation results are in agreement with the experimental one that confirmed the advantages of the filter.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

Millimeter-wave dual-mode and dual-band switchable Gilbert up-conversion mixer in 65-nm CMOS process

2021 ◽  
pp. 1-5
Author(s):  
Fang Zhu ◽  
Guo Qing Luo
Keyword(s):  
Millimeter Wave ◽  
Complementary Metal Oxide Semiconductor ◽  
Local Oscillator ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Dual Band ◽  
Cmos Process ◽  
Pumping Power ◽  
Dual Mode ◽  
Dc Power

Abstract In this paper, a millimeter-wave (MMW) dual-mode and dual-band switchable Gilbert up-conversion mixer in a commercial 65-nm complementary metal oxide semiconductor (CMOS) process is presented. By simply changing the bias, the proposed CMOS Gilbert up-conversion mixer can be switched between subharmonic and fundamental operation modes for MMW dual-band applications. With a low local oscillator pumping power of 3 dBm and low dc power consumption of 6 mW, the proposed CMOS Gilbert up-conversion mixer exhibits a measured conversion gain of −0.5 ± 1.5 dB from 37 to 50 GHz and 2.5 ± 1.5 dB from 17.5 to 32 GHz for the subharmonic and fundamental modes, respectively.

scholarly journals Performance Comparison of Carry-Lookahead and Carry-Select Adders Based on Accurate and Approximate Additions

Electronics ◽  
2018 ◽  
Vol 7 (12) ◽  
pp. 369 ◽  
Author(s):  
Padmanabhan Balasubramanian ◽  
Nikos Mastorakis
Keyword(s):  
High Speed ◽  
Digital Signal ◽  
Complementary Metal Oxide Semiconductor ◽  
Performance Comparison ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Least Significant Bit ◽  
Design Metrics ◽  
Ripple Carry Adder ◽  
Speed Performance

Addition is a fundamental operation in microprocessing and digital signal processing hardware, which is physically realized using an adder. The carry-lookahead adder (CLA) and the carry-select adder (CSLA) are two popular high-speed, low-power adder architectures. The speed performance of a CLA architecture can be improved by adopting a hybrid CLA architecture which employs a small-size ripple-carry adder (RCA) to replace a sub-CLA in the least significant bit positions. On the other hand, the power dissipation of a CSLA employing full adders and 2:1 multiplexers can be reduced by utilizing binary-to-excess-1 code (BEC) converters. In the literature, the designs of many CLAs and CSLAs were described separately. It would be useful to have a direct comparison of their performances based on the design metrics. Hence, we implemented homogeneous and hybrid CLAs, and CSLAs with and without the BEC converters by considering 32-bit accurate and approximate additions to facilitate a comparison. For the gate-level implementations, we considered a 32/28 nm complementary metal-oxide-semiconductor (CMOS) process targeting a typical-case process–voltage–temperature (PVT) specification. The results show that the hybrid CLA/RCA architecture is preferable among the CLA and CSLA architectures from the speed and power perspectives to perform accurate and approximate additions.

Sign in / Sign up

Export Citation Format

Share Document