STRUCTURAL AND ELECTROCHEMICAL PROPERTIES OF THIN LAYERS OF BINARY Ni–Fe ALLOYS ELECTRODEPOSITED BY TWO DIFFERENT BATHS: ACID AND IONIC LIQUID

2018 ◽  
Vol 25 (08) ◽  
pp. 1950025
Author(s):  
RAFIK MAIZI ◽  
ATHMANE MEDDOUR ◽  
CÉLINE ROUSSE
Keyword(s):  
Ionic Liquid ◽  
Nickel Content ◽  
Deposition Potential ◽  
Thin Layers ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Different Shapes ◽  
Fe Alloys ◽  
Irregular Behavior

The deposition of Ni–Fe thin layers in boric acid and ionic liquid ([BuMePyr][Tf2N]) baths were successfully prepared. The obtained materials have been characterized by X-ray diffraction (XRD), Energy Dispersive X-ray spectroscopy (EDX) and SEM. Meanwhile, these materials were carried out by chronoamperometry or chronopotentiometry by varying the intensity of the current and the deposition potential. The results indicate that the coatings of Ni–Fe alloys were successfully obtained by electroplating on the copper substrates, and the alloys composition shows irregular behavior with polarization. The nickel content in the samples is in the range of 55–90%, but the iron content ranges from 10–30%, when potential deposits were varied from [Formula: see text]2[Formula: see text]V to [Formula: see text]4[Formula: see text]V vs Ni electrode. The results also showed that the thin layers are monophased; they contain the Ni3Fe phase. Further, SEM images of Ni–Fe alloys show the different shapes of particles.

Study of Physical Properties of Cadmium Oxide (CdO) and CdO/DNA/RNA Nanostructures Thin Layers Produced by Spray Pyrolysis Technique for Manufacturing Cadmium Oxide (CdO) Nanoparticles and Evaluation of the Effect of DNA/RNA Doping on Their Optical Characteristics

2020 ◽  
Vol 12 (10) ◽  
pp. 1224-1230
Author(s):  
Alireza Heidari
Keyword(s):  
Thin Layer ◽  
Spray Pyrolysis ◽  
Crystalline Structure ◽  
Spray Pyrolysis Technique ◽  
Cadmium Oxide ◽  
Thin Layers ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Cdo Nanoparticles

In the current research, Cadmium Oxide (CdO) nanoparticles are produced by ultrasonic waves and the effect of nucleic acids (DNA/RNA) doping on their optical and structural characteristics are investigated. X-ray Diffraction (XRD) analysis confirms extension of peaks and formation of Cadmium Oxide (CdO) nanoparticles. Absorption spectra for the produced samples are shown that addition of DNA/RNA affects the spectrum and absorption edge shifts towards blue region which is due to reduction of nanoparticle size and it confirms by SEM images. In addition, SEM images show the formation of approximately single size ellipsoidal nanostructures for pure Cadmium Oxide (CdO). However, the size, form and distribution of nanoparticles are varied after doping. On the other hand, in the current paper, Cadmium Oxide (CdO) and DNA/RNA/Cadmium Oxide (CdO) nanostructures thin layers are produced using spray pyrolysis technique over a glassy substrate. Annealing of CdO thin layer for half an hour in the air leads to improvement of crystalline structure. Optical characteristics and crystalline structure of samples are studied through X-ray Diffraction (XRD) and UV-Visible spectroscopy. The results of the current study were shown that CdO thin layers are of hexagonal structure. Further, optical gaff of CdO/DNA/RNA/glass thin layer is increased compared to CdO/glass layer.

Studies about Electrochemical Plating with Zinc - nickel Alloys - the Influence of Deposition Potential on Stoichiometric Composition

2008 ◽  
Vol 59 (9) ◽  
Author(s):  
Violeta Vasilache ◽  
Gheorghe Gutt ◽  
Traian Vasilache
Keyword(s):  
Nickel Alloys ◽  
Stoichiometric Composition ◽  
Nickel Chloride ◽  
Deposition Potential ◽  
X Ray Diffraction ◽  
Pure Zinc ◽  
X Ray ◽  
Nickel Cobalt ◽  
Cobalt Iron ◽  
Electrochemical Plating

The electrochemical deposition of zinc and combinations with elements of the 8th group of the Periodic System (nickel, cobalt, iron) have good properties for anticorrosive protection, compared with pure zinc. For steel pieces, these films delay apparition and formation of white and red iron oxide. We used solutions with different concentrations of zinc chloride, nickel chloride and potassium chloride. To analyze the results we used the optic microscope and the X-ray diffraction.

scholarly journals Hydrochloric Acid Modification and Lead Removal Studies on Naturally Occurring Zeolites from Nevada, New Mexico, and Arizona

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1238
Author(s):  
Garven M. Huntley ◽  
Rudy L. Luck ◽  
Michael E. Mullins ◽  
Nick K. Newberry
Keyword(s):  
New Mexico ◽  
Surface Area ◽  
Bet Surface Area ◽  
Lead Removal ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Naturally Occurring ◽  
27Al Mas Nmr ◽  
Modified Zeolites

Four naturally occurring zeolites were examined to verify their assignments as chabazites AZLB-Ca and AZLB-Na (Bowie, Arizona) and clinoptilolites NM-Ca (Winston, New Mexico) and NV-Na (Ash Meadows, Nevada). Based on powder X-ray diffraction, NM-Ca was discovered to be mostly quartz with some clinoptilolite residues. Treatment with concentrated HCl (12.1 M) acid resulted in AZLB-Ca and AZLB-Na, the chabazite-like species, becoming amorphous, as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na, which are clinoptilolite-like species, withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca 20.0(1) to 111(4) m2/g and NV-Na 19.0(4) to 158(7) m2/g. 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite, and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g compared to the modified zeolites, 30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g, and also decreased upon K+ ion pretreatment in the HCl modified zeolites.

scholarly journals Electrospun Membranes Based on Polycaprolactone, Nano-Hydroxyapatite and Metronidazole

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 931
Author(s):  
Ioana-Codruţa Mirică ◽  
Gabriel Furtos ◽  
Ondine Lucaciu ◽  
Petru Pascuta ◽  
Mihaela Vlassa ◽  
...  
Keyword(s):  
Fiber Diameter ◽  
Maximum Load ◽  
Guided Bone Regeneration ◽  
Attenuated Total Reflectance ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Total Reflectance ◽  
X Ray ◽  
Electrospun Membranes

The aim of this research was to develop new electrospun membranes (EMs) based on polycaprolactone (PCL) with or without metronidazole (MET)/nano-hydroxyapatite (nHAP) content. New nHAP with a mean diameter of 34 nm in length was synthesized. X-ray diffraction (XRD) and attenuated total reflectance Fourier transform infrared spectroscopy (FTIR-ATR) were used for structural characterization of precursors and EMs. The highest mechanical properties (the force at maximum load, Young’s modulus and tensile strength) were found for the PCL membranes, and these properties decreased for the other samples in the following order: 95% PCL + 5% nHAP > 80% PCL + 20% MET > 75% PCL + 5% nHAP + 20% MET. The stiffness increased with the addition of 5 wt.% nHAP. The SEM images of EMs showed randomly oriented bead-free fibers that generated a porous structure with interconnected macropores. The fiber diameter showed values between 2 and 16 µm. The fiber diameter increased with the addition of nHAP filler and decreased when MET was added. New EMs with nHAP and MET could be promising materials for guided bone regeneration or tissue engineering.

Mitrofanovite, Pt3Te4, a new mineral from the East Chuarvy deposit, Fedorovo–Pana intrusion, Kola Peninsula, Russia

2018 ◽  
Vol 83 (4) ◽  
pp. 523-530 ◽  
Author(s):  
Victor V. Subbotin ◽  
Anna Vymazalová ◽  
František Laufek ◽  
Yevgeny E. Savchenko ◽  
Chris J. Stanley ◽  
...  
Keyword(s):  
Kola Peninsula ◽  
Electron Backscatter Diffraction ◽  
New Mineral ◽  
Synthetic Analogue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structural Identity ◽  
Polarised Light ◽  
Fe Alloys ◽  
Backscatter Diffraction

AbstractMitrofanovite, Pt3Te4, is a new telluride discovered in low-sulfide disseminated ore in the East Chuarvy deposit, Fedorovo–Pana intrusion, Kola Peninsula, Russia. It forms anhedral grains (up to ~20 μm × 50 μm) commonly in intergrowths with moncheite in aggregates with lukkulaisvaaraite, kotulskite, vysotskite, braggite, keithconnite, rustenburgite and Pt–Fe alloys hosted by a chalcopyrite–pentlandite–pyrrhotite matrix. Associated silicates are: orthopyroxene, augite, olivine, amphiboles and plagioclase. Mitrofanovite is brittle; it has a metallic lustre and a grey streak. Mitrofanovite has a good cleavage, along {001}. In plane-polarised light, mitrofanovite is bright white with medium to strong bireflectance, slight pleochroism, and strong anisotropy on non-basal sections with greyish brown rotation tints; it exhibits no internal reflections. Reflectance values for the synthetic analogue of mitrofanovite in air (Ro, Re’ in %) are: 58.4, 54.6 at 470 nm; 62.7, 58.0 at 546 nm; 63.4, 59.1 at 589 nm; and 63.6, 59.5 at 650 nm. Fifteen electron-microprobe analyses of mitrofanovite gave an average composition: Pt 52.08, Pd 0.19, Te 47.08 and Bi 0.91, total 100.27 wt.%, corresponding to the formula (Pt2.91Pd0.02)Σ2.93(Te4.02Bi0.05)Σ4.07 based on 7 atoms; the average of eleven analyses on synthetic analogue is: Pt 52.57 and Te 47.45, total 100.02 wt.%, corresponding to Pt2.94Te4.06. The density, calculated on the basis of the formula, is 11.18 g/cm3. The mineral is trigonal, space group R$\overline 3 $m, with a = 3.9874(1), c = 35.361(1) Å, V = 486.91(2) Å3 and Z = 3. The crystal structure was solved and refined from the powder X-ray-diffraction data of synthetic Pt3Te4. Mitrofanovite is structurally and chemically related to moncheite (PtTe2). The strongest lines in the powder X-ray diffraction pattern of synthetic mitrofanovite [d in Å (I) (hkl)] are: 11.790(23)(003), 5.891(100)(006), 2.851(26)(107), 2.137(16)(1013), 2.039(18)(0114), 1.574(24)(0120), 1.3098(21)(0027). The structural identity of natural mitrofanovite with synthetic Pt3Te4 was confirmed by electron backscatter diffraction measurements on the natural sample. The mineral name is chosen to honour Felix P. Mitrofanov, a Russian geologist who was among the first to discover platinum-group element mineralisation in the Fedorova–Pana complex.

Improved Enzymatic Depolymerization of Chitosan by Ionic Liquid Pretreatment and the Effect of Oligo-Chitosan on Intestinal Flora In Vitro

2011 ◽  
Vol 391-392 ◽  
pp. 1319-1323
Author(s):  
Cui Zheng ◽  
Lin Li ◽  
Hao Pang ◽  
Zhao Mei Wang ◽  
Na Li
Keyword(s):  
Ionic Liquid ◽  
Hydrogen Bonds ◽  
Molecular Hydrogen ◽  
Intestinal Flora ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hydrolysis Of ◽  
Positive Effect ◽  
Enzymatic Depolymerization

It still remains challenging for effective hydrolysis of chitosan into chitosan oligomers. In this work, a pretreatment was conducted on chitosan by an ionic liquid 1-butyl-3-methylimidazolium chloride ([C4mim]Cl), aiming at improving enzymatic depolymerization of chitosan. X-ray diffraction analysis indicated that the inter- and intra-molecular hydrogen bonds within chitosan molecules were broken by [C4mim]Cl and the crystalline was destroyed. The oligo-chitosan hydrolyzed from IL-pretreated chitosan, coded as COS-IL, showed a DP of 3~5, in contrast to DP 5~8 with oligo-chitosan obtained from untreated chitosan(coded as COS-UN). COS-IL was more effective than COS-UN in inhibiting intestinal spoilage bacterials growth and it has positive effect on the growth of intestinal probiotic bacterials.

Synthesis of Nickel Hydroxide with Different Morphologies Using an Ionic Liquid

2010 ◽  
Vol 663-665 ◽  
pp. 1163-1166
Author(s):  
Cun Ying Xu ◽  
Yi Xin Hua
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Ionic Liquid ◽  
Volume Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Reaction Media ◽  
Solvothermal Conditions ◽  
Facile Route ◽  
Scanning Electron

A new and facile route has been developed to synthesize β-Ni(OH)2 nanostructures using ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim]BF4) as reaction media under solvothermal conditions. The β-Ni(OH)2 with different morphologies, such as nanoflakes, nanoplatelet and nanorods, can be obtained by controlling the volume ratio of the ionic liquid to water and reaction temperature. The as-prepared products were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM).

scholarly journals Влияние Cr и Ni на формирование фаз в механосинтезированном нанокомпозите на основе Fe-=SUB=-75-=/SUB=-C-=SUB=-25-=/SUB=-

2020 ◽  
Vol 90 (5) ◽  
pp. 787
Author(s):  
А.А. Чулкина ◽  
А.И. Ульянов ◽  
В.А. Волков ◽  
А.Л. Ульянов ◽  
А.В. Загайнов
Keyword(s):  
Curie Temperature ◽  
Amorphous Phase ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
Nickel Content ◽  
X Ray Diffraction ◽  
Mechanical Synthesis ◽  
X Ray ◽  
Higher Temperature ◽  
Two Phases

X-ray diffraction, Mossbauer spectroscopy, and magnetic measurements have been used to study the phase formation and doping during mechanical synthesis (MS) and subsequent annealing of the alloy (Fe0.80Cr0.05Ni0.15)75C25. It has been shown that, after MS, the nanocomposite contains mainly two phases – an amorphous phase and cementite A. During annealing, as a result of crystallization of the amorphous phase, cementite B is formed, in which contains more nickel than in the mechanically synthesized cementite A. As the annealing temperature increases, austenite, which is inhomogeneous in nickel content, is formed. The Curie temperature of this austenite reaches 500 °C. It has been determined that cementite in the mechanosynthesized nanocomposite (Fe,Cr,Ni)75C25 has a higher temperature stabilitythan that in a MS composite (Fe,Ni)75C25.

scholarly journals Influence of pretreatment on the properties of α-Fe2O3 and the effect on photocatalytic degradation of methylene blue under visible light

2020 ◽  
Vol 82 (11) ◽  
pp. 2415-2424
Author(s):  
S. Mokhtari ◽  
N. Dokhan ◽  
S. Omeiri ◽  
B. Berkane ◽  
M. Trari
Keyword(s):  
Methylene Blue ◽  
Average Crystallite Size ◽  
Sample Surface ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Lattice Constants ◽  
Electrochemical Pretreatment ◽  
Crystal Properties ◽  
Rhombohedral Symmetry

Abstract The hematite (α-Fe2O3) nanostructures were synthesized by thermal oxidation of metal at 500 °C under atmospheric pressure. We studied the effect of the electrochemical pretreatment of the substrate before calcinations and its impact on the morphology, crystalline structure, lattice microstructural, and optical properties of α-Fe2O3. Uniform nanosheets were observed on the sample surface after calcination; their dimension and morphology were accentuated by the pretreatment, as confirmed by the SEM images. The characteristics of the nanostructures, analyzed by X-ray diffraction (XRD), revealed a rhombohedral symmetry with the space group R-3c and lattice constants: a = 0.5034 nm and c = 1.375 nm. The average crystallite size and strain, determined from the Williamson-Hall (W-H) plot, showed substantial variations after the substrate pretreatment. The Raman spectroscopy confirmed the changes in the crystal properties of the hematite submitted to pretreatment. The diffuse reflectance allowed to evaluate the optical gap which lies between 1.2 and 1.97 eV, induced by the electrochemical processing. The photocatalytic activity of α-Fe2O3 films was assessed by the degradation of methylene blue (MB) under LED light; 15% enhancement of the degradation for the pretreated specimens was noticed.

Sign in / Sign up

Export Citation Format

Share Document