EXPERIMENTAL POOL BOILING HEAT TRANSFER STUDY OF THE NANOPOROUS COATING IN VARIOUS FLUIDS

2012 ◽  
Vol 20 (01) ◽  
pp. 1150001 ◽  
Author(s):  
SANG M. KWARK ◽  
MIGUEL AMAYA ◽  
SEUNG M. YOU
Keyword(s):  
Pool Boiling ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Apparent Contact Angle ◽  
Pressure Effects ◽  
Wetting Fluids ◽  
Test Pressure ◽  
Coated Surface ◽  
Dry Out ◽  
Transfer Study

An experimental pool boiling study was conducted using plain and nanoporous coated heater surfaces immersed in various working fluids: water, ethanol and HFE-7100. Pool boiling tests were performed on flat 1 cm × 1 cm heaters. Unlike in water, the critical heat flux (CHF) enhancement of the nanoporous coating seems to be less or marginal in ethanol and HFE-7100 at 1 atm. The reduced effect of the nanoporous coating in ethanol and HFE-7100 is believed to be due to the highly wetting nature of these fluids since no obvious difference in wettability is observed between nanoporous coated and uncoated surfaces through apparent contact angle measurement. Moreover, pressure effects were also investigated for the fluids mentioned above. For the nanoporous coated surface, CHF enhancement of the nanoporous coating appeared to be dependent on the test pressure, showing greater CHF enhancement at lower pressure. It is believed that this pressure dependent CHF enhancement behavior could be closely related to the bubble departure diameter. As pressure lowers, the departure bubble size increases and this allows the nanoporous coating to become more influential, even for the highly wetting fluids, in delaying local dry-out, which in turn results in increasing CHF enhancement.

scholarly journals Superhydrophobic functionalized cellulosic paper by copper hydroxide nanorods for oils purification

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ahmed S. Belal ◽  
Jehan El Nady ◽  
Azza Shokry ◽  
Shaker Ebrahim ◽  
Moataz Soliman ◽  
...  
Keyword(s):  
Contact Angle ◽  
Filter Paper ◽  
Separation Efficiency ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Absorption Capacity ◽  
Morphological Properties ◽  
Copper Hydroxide ◽  
Immersion Method ◽  
Water Contact

AbstractOily water contamination has been sighted as one of the most global environmental pollution. Herein, copper hydroxide nanorods layer was constructed onto cellulosic filter paper surface cured with polydopamine, Ag nanoparticles, and Cu NPs through immersion method. This work has been aimed to produce a superhydrophobic and superoleophilic cellulosic filter paper. The structure, crystalline, and morphological properties of these modified cellulosic filter paper were investigated. Scanning electron microscope images confirmed that the modified surface was rougher compared with the pristine surface. The contact angle measurement confirmed the hydrophobic nature of these modified surfaces with a water contact angle of 169.7°. The absorption capacity was 8.2 g/g for diesel oil and the separation efficiency was higher than 99%. It was noted that the flux in the case of low viscosity solvent as n-hexane was 9663.5 Lm−2 h−1, while for the viscous oil as diesel was 1452.7 Lm−2 h−1.

Preparation and the Blood Compatibility of Titanium Oxide Nanorod Arrays

2011 ◽  
Vol 306-307 ◽  
pp. 25-30 ◽  
Author(s):  
Ping Luo ◽  
Zhan Yun Huang ◽  
Di Hu Chen
Keyword(s):  
Contact Angle ◽  
Surface Morphology ◽  
Titanium Oxide ◽  
Tin Oxide ◽  
Growth Parameters ◽  
Blood Compatibility ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Nanorod Arrays ◽  
Wetting Properties

In this work, titanium oxide nanorod arrays were fabricated by using the hydrothermal method on fluorine-doped tin oxide (FTO) coated glass. The diameter of the nanorods could be controlled from 150 nm to 30 nm by changing the growth parameters. The surface morphology and the structure of the samples were characterized by SEM and XRD. The wetting properties were identified by contact angle measurement. Platelet attachment was investigated to evaluate the blood compatibility of the samples with different nanoscale topographies. Results show that the nanotopographical surfaces perform outstanding blood compatibility, and the adhering platelet decreased with the increasing diameter of the nanorods.

Tailoring the in vitro characteristics of poly(vinyl alcohol)-nanohydroxyapatite composite scaffolds for bone tissue engineering

2016 ◽  
Vol 36 (8) ◽  
pp. 771-784 ◽  
Author(s):  
Tejinder Kaur ◽  
Arunachalam Thirugnanam ◽  
Krishna Pramanik
Keyword(s):  
Mechanical Strength ◽  
Vinyl Alcohol ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Poly Vinyl Alcohol ◽  
Apatite Formation ◽  
Composite Scaffolds ◽  
Alizarin Red ◽  
Casting Technique

Abstract Poly(vinyl alcohol) reinforced with nanohydroxyapatite (PVA-nHA) composite scaffolds were developed by varying the nHA (1%, 2%, 3%, 4%, and 5%, w/v) composition in the PVA matrix by solvent casting technique. The developed composite scaffolds were characterized using scanning electron microscopy (SEM), X-ray powder diffraction (XRD), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, and contact angle measurement. The stability of the composite scaffolds in physiological environment was evaluated by swelling and degradation studies. Further, these composite scaffolds were tested for in vitro bioactivity, hemolysis, biocompatibility, and mechanical strength. SEM micrographs showed a homogenous distribution of nHA (3%, w/v) in the PVA matrix. XRD and ATR-FTIR analysis confirmed no phase contamination and the existence of the chemical bond between PVA-nHA at approximately 2474 cm-1. PVA-nHA composite scaffolds with 3% (w/v) concentration of nHA showed nominal swelling and degradation behavior with good mechanical strength. The mechanical strength and degradation properties of the scaffold above 3% (w/v) of nHA was found to deteriorate, which is due to the agglomeration of nHA. The in vitro bioactivity and hemolysis studies showed improved apatite formation and hemocompatibility of the developed scaffolds. In vitro cell adhesion, proliferation, alkaline phosphatase activity, and Alizarin red S staining confirmed the biocompatibility of the composite scaffolds.

Plasma Pre-Treatment of Polyethylene Terephthalate Substrate Influence on the Properties of ZnO Thin Film

2014 ◽  
Vol 895 ◽  
pp. 41-44
Author(s):  
Seiw Yen Tho ◽  
Kamarulazizi Ibrahim
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Polyethylene Terephthalate ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Zno Thin Films ◽  
Zno Thin Film ◽  
Water Contact ◽  
Pre Treatment ◽  
Pet Substrate

In this work, the influences of plasma pre-treatment on polyethylene terephthalate (PET) substrate to the properties of ZnO thin film have been carried out. ZnO thin films were successfully grown on PET substrate by spin coating method. In order to study the effects of plasma pre-treatment, a comparison of treated and untreated condition was employed. Water contact angle measurement had been carried out for PET wettability study prior to ZnO thin film coating. Morphology study of ZnO thin film was performed by scanning probe microscope (SPM). Besides, optical study of the ZnO thin film was done by using UV-vis spectrophotometer. All the measured results show that plasma pre-treatment of PET substrate plays an important role in enhancing the wettability of PET and optical properties of the ZnO thin films. In conclusion, pre-treatment of PET surface is essential to produce higher quality ZnO thin film on this particular substrate in which would pave the way for the integration of future devices.

Measurement of wheel-terrain contact angle for WMRs on rough terrain using laser scanning sensor

2017 ◽  
Vol 44 (6) ◽  
pp. 798-807 ◽  
Author(s):  
He Xu ◽  
Yan Xu ◽  
Peiyuan Wang ◽  
Hongpeng Yu ◽  
Ozoemena Anthony Ani ◽  
...  
Keyword(s):  
Contact Angle ◽  
Laser Scanning ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Rough Terrain ◽  
Wheeled Mobile Robots ◽  
Wheel Slip ◽  
Content Type ◽  
Terrain Model ◽  
Measurement Approach

Purpose The purpose of this paper is to explore a novel measurement approach for wheel-terrain contact angle using laser scanning sensors based on near-terrain perception. Laser scanning sensors have rarely been applied to the measurement of wheel-terrain contact angle for wheeled mobile robots (WMRs) in previous studies; however, it is an effective way to measure wheel-terrain contact angle directly with the advantages of simple, fast and high accuracy. Design/methodology/approach First, kinematics model for a WMR moving on rough terrain was developed, taking into consideration wheel slip and wheel-terrain contact angle. Second, the measurement principles of wheel-terrain contact angle using laser scanning sensors was presented, including “rigid wheel - rigid terrain” model and “rigid wheel - deformable terrain” model. Findings In the proposed approach, the measurement of wheel-terrain contact angle using laser scanning sensors was successfully demonstrated. The rationality of the approach was verified by experiments on rigid and sandy terrains with satisfactory results. Originality/value This paper proposes a novel, fast and effective wheel-terrain contact angle measurement approach for WMRs moving on both rigid and deformable terrains, using laser scanning sensors.

Fabrication and characterization of customized tubular scaffolds for tracheal tissue engineering by using solvent based 3D printing on predefined template

2021 ◽  
Vol 27 (2) ◽  
pp. 421-428
Author(s):  
Rudranarayan Kandi ◽  
Pulak Mohan Pandey ◽  
Misba Majood ◽  
Sujata Mohanty
Keyword(s):  
Tissue Engineering ◽  
Cell Adhesion ◽  
3D Printing ◽  
Chemical Properties ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
In Vitro Cytotoxicity ◽  
Content Type ◽  
Tracheal Tissue

Purpose This paper aims to discuss the successful fabrication of customized tubular scaffolds for tracheal tissue engineering with a novel route using solvent-based extrusion 3D printing. Design/methodology/approach The manufacturing approach involved extrusion of polymeric ink over a rotating predefined pattern to construct customized tubular structure of polycaprolactone (PCL) and polyurethane (PU). Dimensional deviation in thickness of scaffolds were calculated for various layer thicknesses of 3D printing. Physical and chemical properties of scaffolds were investigated by scanning electron microscope (SEM), contact angle measurement, Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction (XRD). Mechanical characterizations were performed, and the results were compared to the reported properties of human native trachea from previous reports. Additionally, in vitro cytotoxicity of the fabricated scaffolds was studied in terms of cell proliferation, cell adhesion and hemagglutination assay. Findings The developed fabrication route was flexible and accurate by printing customized tubular scaffolds of various scales. Physiochemical results showed good miscibility of PCL/PU blend, and decrease in crystalline nature of blend with the addition of PU. Preliminary mechanical assessments illustrated comparable mechanical properties with the native human trachea. Longitudinal compression test reported outstanding strength and flexibility to maintain an unobstructed lumen, necessary for the patency. Furthermore, the scaffolds were found to be biocompatible to promote cell adhesion and proliferation from the in vitro cytotoxicity results. Practical implications The attempt can potentially meet the demand for flexible tubular scaffolds that ease the concerns such as availability of suitable organ donors. Originality/value 3D printing over accurate predefined templates to fabricate customized grafts gives novelty to the present method. Various customized scaffolds were compared with conventional cylindrical scaffold in terms of flexibility.

Influence of micro-nano surface texture on the hydrophobicity and corrosion resistance of a Ti6Al4V alloy surface

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Bochun Xu ◽  
Nan Zou ◽  
Yunhao Jia ◽  
Chao Feng ◽  
Jiajia Bu ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Titanium Alloy ◽  
Surface Texture ◽  
Surface Hydrophobicity ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Alloy Surface ◽  
Measurement Instruments ◽  
Content Type

Purpose The purpose of this paper is to study the effect of micro-nano surface texture on the corrosion resistance of a titanium alloy and investigate the correlation between corrosion resistance and hydrophobicity. Design/methodology/approach The surface of the Ti6Al4V alloy was modified by laser processing and anodizing to fabricate micro-pits, nanotubes and micro-nano surface textures. Afterward, the surface morphology, hydrophobicity and polarization curve of the samples were analyzed by cold field scanning electron microscopy, contact angle measurement instruments and a multi-channel electrochemical workstation. Findings The micro-nano surface texture can enhance the hydrophobicity of the Ti6Al4V surface, which may lead to better drag reduction to ease the friction of implants in vivo. Nevertheless, no correlation existed between surface hydrophobicity and corrosion resistance; the corrosion resistance of samples with nanotubes and high-density samples with micro-nano surface texture was extremely enhanced, indicating the similar corrosion resistance of the two. Research limitations/implications The mechanism of micro-dimples on the corrosion resistance of the micro-nano surface texture was not studied. Practical implications The density of micro-pits needs to be optimized to guarantee excellent corrosion resistance in the design of the micro-nano surface texture; otherwise, it will not fulfill the requirement of surface modification. Originality/value The influence of the micro-nano surface texture on the corrosion resistance, as well as the relationship between hydrophobicity and corrosion resistance of the titanium alloy surface, were systematically investigated for the first time. These conclusions offer new knowledge.

Contact Angle of Nepenthes alata Slippery Zone: Results from Measurement and Model Analysis

2021 ◽  
pp. 1-7
Author(s):  
Lixin Wang ◽  
Pan Pan ◽  
Shixing Yan ◽  
Shiyun Dong
Keyword(s):  
Contact Angle ◽  
Hierarchical Structures ◽  
Model Analysis ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Structure Characteristic ◽  
Baxter Equation ◽  
Measured Contact Angle ◽  
The Relationship ◽  
Contact Angle Analysis

The slippery zone of Nepenthes alata depends on its highly evolved morphology and structure to show remarkable superhydrophobicity, which has gradually become a biomimetic prototype for developing superhydrophobic materials. However, the mechanism governing this phenomenon has not been fully revealed through model analysis. In this paper, the superhydrophobicity of slippery zone is studied by contact angle measurement, morphology/structure examination and model analysis. The slippery zone causes ultrapure water droplet to produce a considerably high contact angle (155.11–158.30°), and has a micro-nano scale hierarchical structures consisting of lunate cells and wax coverings. According to the Cassie-Baxter equation and a self-defined infiltration coefficient, a model was established to analyze the effect of structure characteristic on the contact angle. Analysis result showed that the calculated contact angle (154.67–159.49°) was highly consistent with the measured contact angle, indicating that the established model can quantitatively characterize the relationship between the contact angle and the structure characteristic. Our study provides some evidences to further reveal the superhydrophobic mechanism of Nepenthes alata slippery zone, as well as inspires the biomimetic development of superhydrophobic surfaces.

Effect of 2D Alpha-Zirconium Phosphate Nanosheets in Interfacial Tension Reduction and Wettability Alteration: Implications for Enhanced Oil Recovery

SPE Journal ◽  
2022 ◽  
pp. 1-13
Author(s):  
Song Qing ◽  
Hong Chen ◽  
Li-juan Han ◽  
Zhongbin Ye ◽  
Yihao Liao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Zirconium Phosphate ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Wettability Alteration ◽  
Tetrabutylammonium Hydroxide ◽  
Transmission Electron ◽  
2D Nanosheets

Summary α-Zirconium phosphate (α-ZrP) nanocrystals were synthesized by refluxing method and subsequently exfoliated into extremely thin 2D nanosheets by tetrabutylammonium hydroxide (TBAOH) solution. Dynamic light scattering, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to characterize the size distribution and morphology of α-ZrP nanosheets. Interfacial tension (IFT) and contact angle measurement were conducted by different concentrations of α-ZrP nanosheets solutions. The results displayed that the wettability of porous media surface was altered from oleophilic to hydrophilic and the IFT decreased with the increasing of α-ZrP nanosheets concentrations. A new method was proposed to calculate the Hamaker constant for 2D α-ZrP nanosheets. The calculated results displayed that α-ZrP nanosheets were not easy to agglomerate under experimental environment and when the interaction energy barrier increased, the transport amount of α-ZrP nanosheets also increased. Coreflooding tests were also performed with various concentrations and the oil recovery efficiency increased from 33.59 to 51.26% when α-ZrP nanosheets concentrations increased from 50 to 1,000 ppm.

Sign in / Sign up

Export Citation Format

Share Document