Second Step Aging on Nanosized Precipitates and Properties of Al–Zn–Mg–Cu–Cr Spray-Deposited Alloys

2020 ◽  
Vol 20 (3) ◽  
pp. 1955-1961
Author(s):  
Guo Gong ◽  
Linying Zhang ◽  
Haijun Yuan ◽  
Jianbing Jiang ◽  
Min Ouyang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Aging Time ◽  
Testing Machine ◽  
Impact Testing ◽  
Second Step ◽  
Fine Grain ◽  
Tensile Tester ◽  
Transmission Electron ◽  
The Matrix ◽  
Boundary Width

The effects of second step aging (T76, T74, T73) on nano-sized precipitates and properties of Al–Zn–Mg–Cu–Cr spray-deposited alloys were explored through tensile tester, impact testing machine, metallographic microscope (OM), eddy-current device, scanning electron microscopy (SEM), twin-jet electro-polishing machine and transmission electron microscopy (TEM). Fine grain size (compared with as-deposited billet) and directional microstructures were obtained. T76 heat treatment of the alloy provided higher tensile strength, yield strength, impact toughness and hardness which were 767 MPa, 708 MPa, 39.41 J/cm1/2 99.1 HRB, respectively in comparison with T74 and T73 samples. However, they provided lower elongation and electrical conductivity which were 7.6% and 31.1% IACS, respectively in comparison with T74 and T73 samples. This resulted from the larger quantity and volume of tiny η′ precipitates that distribute homogeneously in matrix. However, coarse precipitates with increasing second step aging time (T74, T73) made wider grain boundary width and discontinuous η precipitates boosted conductivity of the Al–Zn–Mg–Cu–Cr alloy. Furthermore, proportion of white precipitated phase in the matrix decreased slightly and volume became larger with increasing second step aging time.

EFFECT OF CALCIUM SULPHATE NANOPARTICLES ON FUSION, MECHANICAL AND THERMAL BEHAVIOUR POLYVINYL CHLORIDE (PVC)

2010 ◽  
Vol 24 (01n02) ◽  
pp. 64-75 ◽  
Author(s):  
C. B. PATIL ◽  
P. S. SHISODE ◽  
U. R. KAPADI ◽  
D. G. HUNDIWALE ◽  
P. P. MAHULIKAR
Keyword(s):  
Electron Microscopy ◽  
Testing Machine ◽  
Calcium Sulphate ◽  
Filler Loading ◽  
Mechanical And Thermal Properties ◽  
Melt Mixing ◽  
Transmission Electron ◽  
In Situ Deposition ◽  
The Matrix ◽  
Internal Mixer

Calcium Sulphate [ CaSO 4] was synthesized by in-situ deposition technique and its nano size (60 to 100 nm) was confirmed by Transmission Electron Microscopy (TEM). Composites of the filler CaSO 4 (micro and nano) and the matrix poly (vinyl chloride) ( PVC ) were prepared with different filler loading (0-5 wt. %) by melt mixing. The Brabender torque rheometer equipped with an internal mixer was used for preparation and evaluation of fusion behaviour of composites of different formulations. The effect of nano and micro- CaSO 4 content on the structure and properties of composites was studied. The nanostructures and dispersion were studied by wide angle X-ray diffraction (WAXD) and scanning electron microscopy (SEM). The mechanical and thermal properties of PVC / micro and nano- CaSO 4 composites were characterized using Universal Testing Machine (UTM) and Thermo Gravimetric Analyzer (TGA). From the results of WAXD and SEM the flocculation of CaSO 4 nanoparticles were observed on the surfaces of PVC matrix. The thermal analysis results showed that the first thermal degradation onset (T onset) of PVC /nano- CaSO 4 composites for 1 wt. % of filler were higher as compared with corresponding microcomposites and pristine PVC . However, the tensile strength was decreasing with increasing filler content while, it shows increment in magnitude at 1 and 2 wt. % of nano- CaSO 4 as compared with corresponding micro- CaSO 4 as well as pristine PVC .

scholarly journals Effect of Aging Time on Crushing Performance of Al-0.5Mg-0.4Si Alloy for Safety Components of Automobile

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 608
Author(s):  
Jinkun Lu ◽  
Haichun Jiang ◽  
Lingying Ye ◽  
Daxiang Sun ◽  
Yong Zhang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Tensile Test ◽  
Aging Time ◽  
Uniform Elongation ◽  
Total Elongation ◽  
Localized Deformation ◽  
Ductility Index ◽  
Transmission Electron ◽  
The Difference

The effect of aging time on the crushing performance of Al-0.5Mg-0.4Si alloy used for safety components of automobile was investigated by tensile test and crush test. Moreover, the microstructure of the alloy was investigated by transmission electron microscopy (TEM). The results show that the localized deformation ductility index, ΔAabs, which is defined as the difference between total elongation and uniform elongation, of Al-0.5Mg-0.4Si alloy is 6.5%, 7.0% and 8.5%, respectively, after being aged at 210 °C for 1, 3 and 6 h, and this tendency is the same as that of the crushing performance. The spacing of grain boundary precipitates (GBPs) from TEM results are found to be 94.9, 193.6 and 408.2 nm after being aged at 210 °C for 1, 3 and 6 h, respectively, and this tendency is same to that of ΔAabs. A mechanism about the relation between the spacing of GBPs and the ductility index ΔAabs has been proposed based on localized deformation around GBPs. With the increase of GBPs spacing, the ΔAabs increases, and the crushing performance is improved.

scholarly journals Oxygen Induced Phase Transformation in TC21 Alloy with a Lamellar Microstructure

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 163
Author(s):  
Shu Wang ◽  
Yilong Liang ◽  
Hao Sun ◽  
Xin Feng ◽  
Chaowen Huang
Keyword(s):  
Electron Microscopy ◽  
Phase Transformation ◽  
Oxygen Uptake ◽  
Titanium Alloys ◽  
Electron Backscatter Diffraction ◽  
Lamellar Microstructure ◽  
Α Phase ◽  
Transmission Electron ◽  
The Matrix ◽  
Oxygen Ingress

The main objective of the present study was to understand the oxygen ingress in titanium alloys at high temperatures. Investigations reveal that the oxygen diffusion layer (ODL) caused by oxygen ingress significantly affects the mechanical properties of titanium alloys. In the present study, the high-temperature oxygen ingress behavior of TC21 alloy with a lamellar microstructure was investigated. Microstructural characterizations were analyzed through optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). Obtained results demonstrate that oxygen-induced phase transformation not only enhances the precipitation of secondary α-phase (αs) and forms more primary α phase (αp), but also promotes the recrystallization of the ODL. It was found that as the temperature of oxygen uptake increases, the thickness of the ODL initially increases and then decreases. The maximum depth of the ODL was obtained for the oxygen uptake temperature of 960 °C. In addition, a gradient microstructure (αp + β + βtrans)/(αp + βtrans)/(αp + β) was observed in the experiment. Meanwhile, it was also found that the hardness and dislocation density in the ODL is higher than that that of the matrix.

Atomic-scale structural and compositional analyses of Ruddlesden-Popper planar faults in AO-excess SrTiO3 (A = Sr2+, Ca2+, Ba2+) ceramics

2009 ◽  
Vol 24 (8) ◽  
pp. 2596-2604 ◽  
Author(s):  
Sašo Šturm ◽  
Makoto Shiojiri ◽  
Miran Čeh
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Dark Field ◽  
Atomic Scale ◽  
Transmission Electron ◽  
Initial Stage ◽  
Final Microstructure ◽  
Scanning Transmission ◽  
The Matrix ◽  
Annular Dark Field

The microstructure in AO-excess SrTiO3 (A = Sr2+, Ca2+, Ba2+) ceramics is strongly affected by the formation of Ruddlesden-Popper fault–rich (RP fault) lamellae, which are coherently intergrown with the matrix of the perovskite grains. We studied the structure and chemistry of RP faults by applying quantitative high-resolution transmission electron microscopy and high-angle annular dark-field scanning transmission electron microscopy analyses. We showed that the Sr2+ and Ca2+ dopant ions form RP faults during the initial stage of sintering. The final microstructure showed preferentially grown RP fault lamellae embedded in the central part of the anisotropic perovskite grains. In contrast, the dopant Ba2+ ions preferably substituted for Sr2+ in the SrTiO3 matrix by forming a BaxSr1−xTiO3 solid solution. The surplus of Sr2+ ions was compensated structurally in the later stages of sintering by the formation of SrO-rich RP faults. The resulting microstructure showed RP fault lamellae located at the surface of equiaxed BaxSr1-xTiO3 perovskite grains.

The Impact Properties of a Polyurethane Composite Filled with Clay

2011 ◽  
Vol 197-198 ◽  
pp. 1100-1103
Author(s):  
Jian Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Mechanical Analysis ◽  
Impact Testing ◽  
Impact Properties ◽  
Polyurethane Composite ◽  
The Matrix ◽  
The Impact ◽  
Scanning Electron

A polyurethane/clay (PU/clay) composite was synthesized. The microstructure of the composite was examined by scanning electron microscopy. The impact properties of the composite were characterized by impact testing. The study on the structure of the composite showed that clays could be dispersed in the polymer matrix well apart from a few of clusters. The results from mechanical analysis indicated that the impact properties of the composite were increased greatly in comparison with pure polyurethane. The investigation on the mechanical properties showed that the impact strength could be obviously increased by adding 20 wt% (by weight) clay to the matrix.

Microstructural Characterization, Mechanical Properties and Wear Resistance of TiCP Reinforced Ni-Alloy Coatings by Laser Synthesis

2000 ◽  
Author(s):  
D. L. Tu ◽  
A. Kar ◽  
X. L. Wu
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Wear Resistance ◽  
Chemical Reaction ◽  
Phase Interface ◽  
High Fracture Toughness ◽  
Transmission Electron ◽  
Ni Alloy ◽  
The Matrix

Abstract Titanium carbide particle (TiCp)-reinforced Ni alloy composite coatings are synthesized by laser cladding using a cw 3 kW CO2 laser. Two kinds of coatings are possible in terms of the origin of TiCp: undissolved TiCp and in-situ generated TiCp. The former originates from the TiCp pre-coated on the sample whereas the latter from in-situ chemical reaction between titanium and graphite in the molten pool during laser irradiation. For the coating reinforced by TiCp formed in-situ, the sub-micron TiCp particles are formed and uniformly distributed because of the in-situ reaction and trapping effect during rapid solidification. Graded distribution of TiCp is obtained on a macro scale. The volume fraction increases from 1.86% at the coating-substrate interface to 38.4% at the coating surface. For the coating reinforced by undissolved TiCp, analytical transmission electron microscopy (ATEM) and high resolution transmission electron microscopy (HRTEM) observations show the existence of the epitaxial growth of TiC, the precipitation of CrB and M23C6, and the chemical reaction between Ti and B elements around phase interfaces of undissolved TiCp. In the matrix near the phase interface of undissolved TiCp, the loading curve obtained by nanoindenter exhibits pop-in phenomena due to the plastic deformation of cracks or debonding of TiCp from the matrix. For TiCp generated in-situ, no pop-in mark appears, indicating high fracture toughness. Coating with TiCp generated in-situ exhibits higher hardness and modulus than the coating with undissolved TiCp at regions near the phase interface. The coating reinforced by TiCp generated in-situ also displays higher impact wear resistance and abrasive wear resistance compared to the coatings with undissolved TiCp and without TiCp respectively.

scholarly journals Improving the Damping Properties of Nanocomposites by Monodispersed Hybrid POSS Nanoparticles: Preparation and Mechanisms

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 647 ◽  
Author(s):  
Wei Wei ◽  
Yingjun Zhang ◽  
Meihua Liu ◽  
Yifan Zhang ◽  
Yuan Yin ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Damping Factor ◽  
Damping Properties ◽  
Molecular Weights ◽  
Organic Hybrid ◽  
Transmission Electron ◽  
The Matrix ◽  
Movement Ability ◽  
Tan Δ ◽  
Oligomeric Silsesquioxane

In this work, a series of heptaphenyl siloxane trisilanol/polyhedral oligomeric silsesquioxane (T7-POSS) modified by polyols with different molecular weights were synthesized into liquid-like nanoparticle–organic hybrid materials using the grafted-from method. All grafted POSS nanoparticles changed from solid powders to liquid at room temperature. Polyurethane (PU) nanocomposites with POSS contents ranging from 1.75 to 9.72 wt % were prepared from these liquefied polyols-terminated POSS with polyepichlorohydrin (POSS–PECH). Transmission electron microscopy (TEM), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to characterize the morphology of the POSS–PECH/PU nanocomposites. The results showed that the polyol-terminated POSS particles overcame the nanoagglomeration effect and evenly disperse in the polymeric matrix. The damping factor (tan δ) of resultant nanocomposites increased from 0.90 to 1.16, while the glass transition temperature decreased from 15.8 to 9.4 °C when POSS contents increased from 0 to 9.75 wt %. The gel content, tensile strength and Fourier transform infrared (FTIR) analyses demonstrated that the molecular thermal movement ability of the polyurethane (PU) matrix increased with increasing POSS hybrid content. Therefore, the improvement of the damping properties of the composites was mainly due to the friction-related losses occurring in the interface region between the nanoparticles and the matrix.

scholarly journals The Influence of A Mo Addition on the Interfacial Morphologies and Corrosion Resistances of Novel Fe-Cr-B Alloys Immersed in Molten Aluminum

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 256 ◽  
Author(s):  
Zicheng Ling ◽  
Weiping Chen ◽  
Weiye Xu ◽  
Xianman Zhang ◽  
Tiwen Lu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Electron Probe ◽  
Molten Aluminum ◽  
Dendritic Structure ◽  
H13 Steel ◽  
X Ray ◽  
Transmission Electron ◽  
The Matrix ◽  
Scanning Electron

The influence of a Mo addition on the interfacial morphologies and corrosion resistances of novel Fe-Cr-B alloys in molten aluminum at 750 °C was systematically investigated using scanning electron microscopy, X-ray diffractometer, electron probe microanalysis, and transmission electron microscopy. The results indicated that Mo could not only strengthen the matrix but also facilitate the formation of borides. Furthermore, the microstructures of Mo-rich M2B boride changed from a local eutectic net-like structure to a typical coarse dendritic structure and a blocky hypereutectic structure with increasing Mo addition. This was true of the blocky Mo-rich M2B boride, rod-like Cr-rich M2B boride and the corrosion products, which had a synergistic effect on retarding of the diffusion of molten aluminum. Notably, the corrosion resistance of the Fe-Cr-B-Mo alloy, with an 8.3 wt.% Mo addition, was 3.8 times higher than that of H13 steel.

Fracture behavior and deformation mechanisms of polypropylene/ethylene-propylene-diene blends

2016 ◽  
Vol 36 (7) ◽  
pp. 695-704 ◽  
Author(s):  
Yuhui Ao ◽  
Fang Feng ◽  
Huixuan Zhang
Keyword(s):  
Electron Microscopy ◽  
Deformation Mechanism ◽  
Fracture Behavior ◽  
Rubber Particle ◽  
Shear Yielding ◽  
Ethylene Propylene ◽  
Transmission Electron ◽  
Rubber Particles ◽  
The Matrix ◽  
Matrix Shear

Abstract The fracture behavior and deformation mechanism of polypropylene (PP)/ethylene-propylene-diene rubber (EPDM) were studied by scanning electron microscopy and transmission electron microscopy analyses. The deformation mechanism was investigated under different conditions. Voids were seen under all the conditions because of matrix shear yielding, indicating that rubber particle cavitation took place during the blend fracture process; moreover, the void size and density increased as the fracture surface was approached. However, the void density and extent of elongation of the rubber particles in the deformation zone decreased with increasing test speed rate. Many voids were positioned in the rubber particles, confirming that matrix shear yielding initiated by rubber particle cavitation was the main deformation mechanism during ductile fracture in the matrix.

Preparation and characterization emulsion of PANI-TiO2 nanocomposite and its application as anticorrosive coating

2015 ◽  
Vol 35 (6) ◽  
pp. 597-603 ◽  
Author(s):  
Mohsen Khademian ◽  
Hossein Eisazadeh
Keyword(s):  
Electron Microscopy ◽  
Colloidal Particles ◽  
Aqueous Media ◽  
Corrosion Current ◽  
Ammonium Persulfate ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
The Matrix ◽  
Definition Of

Abstract Emulsion nanoparticles of polyaniline (PANI) were synthesized in the aqueous media by using hydroxylpropylcellulose (HPC) as a stabilizer and ammonium persulfate as an oxidant in the presence of TiO2 with nanometer size. New poly(vinyl acetate) (PVAc) coating over carbon steel was prepared by addition of emulsion nanoparticles in different concentrations (1%, 2% and 1.5%) in PVAc as the major matrix. The Tafel plot records were used for the definition of potential and corrosion current (Icorr). Nanoparticles were characterized and compared by X-ray diffraction (XRD), thermal gravimetric analysis (TGA), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). By adding TiO2, the thermal stability of the nanocomposite increased. A small size of colloidal particles prevented the precipitation of conducting polymer particles and led to better dispersion of nanocomposites in the matrix of the PVAc binder; therefore, the paint was homogeneous and anticorrosion properties of the coating increased. According to the results, 1.5% of PANI-TiO2 nanocomposite in PVAc has a much lower Icorr in NaCl aqueous solution and 2% of PANI-TiO2 nanocomposite in PVAc has the best corrosion protection in HCl.

Sign in / Sign up

Export Citation Format

Share Document