scholarly journals Assessment of a smart concept for d15 shear piezoceramic direct torsion actuation

2011 ◽  
pp. 103-124
Author(s):  
Ayech Benjeddou
Keyword(s):  
Shear Modulus ◽  
Modal Analysis ◽  
Parametric Analysis ◽  
Open Circuit ◽  
Bonding Parameters ◽  
The Core ◽  
Performance Reduction ◽  
And Performance ◽  
Deflection Criteria ◽  
The Cost

An experimentally proved smart concept for piezoceramic direct torsion actuation is here numerically assessed with regards to the bonding and segmentation influence on its behavior and performance. The TRESCA and deflection criteria analysis indicates that the actuator sandwiching with composites contributes to its integrity enhancement, but in the cost of its performance reduction. It is also found that modeling the core inter-rows and composites inter-layers bonding is more influential than that of the core rows segmentation. The conducted open-circuit modal analysis confirms that the inter-rows adhesive softens the actuator, while the inter-layers one stiffens it. Besides, the conducted adhesive parametric analysis indicates that, as expected, the most influential bonding parameters are its thickness and shear modulus.

Return on Invesment (ROI) of Software Product: A Systematic Literature Review

2015 ◽  
Vol 6 (1) ◽  
pp. 50-57
Author(s):  
Rizqa Raaiqa Bintana ◽  
Putri Aisyiyah Rakhma Devi ◽  
Umi Laili Yuhana
Keyword(s):  
Return On Investment ◽  
Assessment Criteria ◽  
Software Product ◽  
And Performance ◽  
Rational Consideration ◽  
Actual Return ◽  
The Cost ◽  
Investment Models ◽  
The Impact

The quality of the software can be measured by its return on investment. Factors which may affect the return on investment (ROI) is the tangible factors (such as the cost) dan intangible factors (such as the impact of software to the users or stakeholder). The factor of the software itself are assessed through reviewing, testing, process audit, and performance of software. This paper discusses the consideration of return on investment (ROI) assessment criteria derived from the software and its users. These criteria indicate that the approach may support a rational consideration of all relevant criteria when evaluating software, and shows examples of actual return on investment models. Conducted an analysis of the assessment criteria that affect the return on investment if these criteria have a disproportionate effort that resulted in a return on investment of a software decreased. Index Terms - Assessment criteria, Quality assurance, Return on Investment, Software product

Emotional Choices

2018 ◽  
Author(s):  
Robin Markwica
Keyword(s):  
Decision Making ◽  
Choice Behavior ◽  
Choice Theory ◽  
Cuban Missile Crisis ◽  
Coercive Diplomacy ◽  
The Core ◽  
Present Book ◽  
Action Model ◽  
The Cost ◽  
Dynamic Interplay

In coercive diplomacy, states threaten military action to persuade opponents to change their behavior. The goal is to achieve a target’s compliance without incurring the cost in blood and treasure of military intervention. Coercers typically employ this strategy toward weaker actors, but targets often refuse to submit and the parties enter into war. To explain these puzzling failures of coercive diplomacy, existing accounts generally refer to coercers’ perceived lack of resolve or targets’ social norms and identities. What these approaches either neglect or do not examine systematically is the role that emotions play in these encounters. The present book contends that target leaders’ affective experience can shape their decision-making in significant ways. Drawing on research in psychology and sociology, the study introduces an additional, emotion-based action model besides the traditional logics of consequences and appropriateness. This logic of affect, or emotional choice theory, posits that target leaders’ choice behavior is influenced by the dynamic interplay between their norms, identities, and five key emotions, namely fear, anger, hope, pride, and humiliation. The core of the action model consists of a series of propositions that specify the emotional conditions under which target leaders are likely to accept or reject a coercer’s demands. The book applies the logic of affect to Nikita Khrushchev’s decision-making during the Cuban missile crisis in 1962 and Saddam Hussein’s choice behavior in the Gulf conflict in 1990–91, offering a novel explanation for why coercive diplomacy succeeded in one case but not in the other.

Parametric analysis and performance of laser cutting on strenx steel

2020 ◽  
Author(s):  
K. Muralidharan ◽  
S. Shalini Packiam Kamala ◽  
D. Alankrutha ◽  
K. Bhanu Prakash ◽  
Ram Subbiah ◽  
...  
Keyword(s):  
Laser Cutting ◽  
Parametric Analysis ◽  
And Performance

Construction of MOFs-Shell Porous Materials and Performance Study in Selective Adsorption and Separation of Benzene Pollutants

2021 ◽  
Author(s):  
Yu Qiao ◽  
Na Lv ◽  
Dong Li ◽  
Hongji Li ◽  
Xiangxin Xue ◽  
...  
Keyword(s):  
Porous Materials ◽  
Shell Structure ◽  
Selective Adsorption ◽  
Core Shell ◽  
Architecture Design ◽  
Performance Study ◽  
The Core ◽  
Core Shell Structure ◽  
And Performance ◽  
Sacrificial Agent

Metastable Cu2O is an attractive material for the architecture design of integrated nanomaterials. In this context, Cu2O was used as the sacrificial agent to form the core-shell structure of Cu2O@HKUST-1...

scholarly journals Effects of Structural Parameters on Seismic Behaviour of Historical Masonry Minaret

2017 ◽  
Author(s):  
Barış Erdil ◽  
Mücip Tapan ◽  
İsmail Akkaya ◽  
Fuat Korkut
Keyword(s):  
Modal Analysis ◽  
Structural Parameters ◽  
Masonry Structure ◽  
Operational Modal Analysis ◽  
Shear Cracks ◽  
Seismic Behaviour ◽  
New Model ◽  
The Core ◽  
Historical Masonry ◽  
Stiffness Distribution

The October 23, 2011 (Mw = 7.2) and November 9, 2011 (Mw = 5.6) earthquakes increased the damage in the minaret of Van Ulu Mosque, an important historical masonry structure built with solid bricks in Eastern Turkey, resulting in significant shear cracks. It was found that since the door and window openings are not symmetrically placed, they result in unsymmetrical stiffness distribution. The contribution of staircase and the core on stiffness is ignorable but its effect on the mass is significant. The pulpit with chamfered corner results in unsymmetrical transverse displacements. Brace wall improves the stiffness however contributes to the unsymmetrical behaviour considerably. The reason for the diagonal cracks can be attributed to the unsymmetrical brace wall and the chamfered pulpit but the effect of brace wall is more pronounced. After introducing the cracks, a new model was created and calibrated according to the results of Operational Modal Analysis. Diagonal cracks were found to be likely to develop under earthquake loading. Drifts are observed to increase significantly upon the introduction of the cracks.

STUDY ON THE PROCESS OF RAPESEED HULLING BY THE IMPACT

2019 ◽  
Author(s):  
А.О. РЕНЗЯЕВ ◽  
О.П. РЕНЗЯЕВ ◽  
С.Н. КРАВЧЕНКО ◽  
Р.В. КРЮК
Keyword(s):  
Rotational Speed ◽  
Calculated Data ◽  
Quality Characteristics ◽  
Complete Separation ◽  
Edible Oil ◽  
Siberian Region ◽  
The Core ◽  
The Cost ◽  
The Impact

Исследованы прочностные и физико-механические свойства оболочки рапса с точки зрения ее разрушения и удаления. Установлено, что наиболее рациональным является двухстадийный способ обрушивания: 1-я стадия – на вальцовых мельницах, 2-я – на центробежной обрушивающей машине. Определены параметры центробежной обрушивающей машины для обеспечения минимальной необходимой линейной скорости 10,81 м/с: угол наклона отбойной пластины (90 ± 2)°, частота вращения барабана (2400 ± 150) об/мин. Установлено, что правильно подобранные условия и угол, под которым происходит удар, позволяют значительно снизить количество не до конца обрушенного семени и содержание расколотого ядра. При этом при свободном ударе об отбойную пластину под углом, отличным от 88–91°, или подаче недостаточно равномерного потока семян значительно увеличивается содержание необрушенных семян. На разрушение 1 кг семян необходимо затратить 58,45 Дж. Таким образом, по расчетным данным, для семян рапса диаметром 1,5 мм частота вращения барабана должна находиться в диапазоне от 2221 до 2565 об/мин при ударе семени под углом 90°. Диаметр семян рапса, выращиваемого в Сибирском регионе, составляет от 0,8 до 1,8 мм. Установлено, что подсушивание семян рапса в течение 30–40 с при температуре 100°С позволяет увеличить эффективность разрушения оболочки до полного ее отделения от ядра рапса. Представленные результаты позволяют повысить качество очистки семян рапса от оболочки и улучшить качественные характеристики получаемого масла, облегчить последующие технологические процессы получения пищевого масла, снизить затраты на рафинацию и дезодорацию на 2%. The strength and physico-mechanical properties of the shell of rapeseed in terms of its destruction and removal are investigated. It is established that the most rational is a two-stage method of seed hulling: the 1st stage – on roller mills, the 2nd – on a centrifugal hulling machine. The parameters of the centrifugal hulling machine to provide the minimum required linear speed of 10,81 m/s are defined: the angle of inclination of the turnback plate (90 ± 2)°, the rotational speed of drum (2400 ± 150) RPM. It is established that the correctly selected conditions and the angle at which the impact occurs, can significantly reduce the amount is not completely hulling seed and the substance of the split nucleus. At the same time, with a free impact on the turnback plate at an angle different from 88–91°, or the supply of an insufficiently uniform flow of seeds, the content is not completely hulling seed increases significantly. On hulling of 1 kg of seeds it is necessary to spend 58,45 J. Thus, according to the calculated data, for rape seeds with a diameter of 1,5 mm, the rotational speed of drum should be in the range from 2221 to 2565 RPM when the seed is struck at an angle of 90°. The diameter of rapeseed grown in the Siberian region ranges from 0,8 to 1,8 mm. It was found that drying of rapeseed for 30–40 s at a temperature of 100°C, can increase the efficiency of destruction of the shell to its complete separation from the core of rapeseed. The presented results make it possible to improve the quality of cleaning of rape seeds from the shell and improve the quality characteristics of the obtained oil, facilitate the subsequent technological processes of obtaining edible oil, reduce the cost of refining and deodorization by 2%.

Characterisation of Static Strip Seal Flow

2007 ◽  
Author(s):  
Arash Farahani ◽  
Peter Childs
Keyword(s):  
Gas Flow ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Main Stream ◽  
Cfd Modelling ◽  
Height Range ◽  
And Performance ◽  
Nozzle Guide ◽  
The Cost ◽  
Cooling Air

Strip seals are used in gas turbine engines between two static elements or between components which do not move relative to each other, such as Nozzle Guide Vanes (NGVs). The key role of a strip seal between NGV segments is sealing between the flow through the main stream annulus and the internal air system, a further purpose is to limit the inter-segmental movements. In general the shape of the strip seal is a rectangular strip that fits into two slots in adjacent components. The minimum clearance required for static strip seals must be found by accounting for thermal expansion, misalignment, and application, to allow correct fitment of the strip seals. Any increase in leakage raises the cost due to an increase in the cooling air use, which is linked to specific fuel consumption, and it can also alter gas flow paths and performance. The narrow path within the seal assembly, especially the height has the most significant affect on leakage. The height range of the narrow path studied in this paper is 0.01–0.06 mm. The behaviour of the flow passing through the narrow path has been studied using CFD modelling and measurements in a bespoke rig. The CFD and experimental results show that normalized leakage flow increases with pressure ratio before reaching a maximum. The main aim of this paper is to provide new experimental data to verify the CFD modelling for static strip seals. The typical flow characteristics validated by CFD modelling and experiments can be used to predict the flow behaviour for future static strip seal designs.

scholarly journals Alert: An Adaptive Low-Latency Event-Driven MAC Protocol for Wireless Sensor Networks

2011 ◽  
Vol 2011 ◽  
pp. 1-19
Author(s):  
Vinod Namboodiri ◽  
Abtin Keshavarzian
Keyword(s):  
Mac Protocol ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Network Applications ◽  
Alarm Systems ◽  
Minimum Latency ◽  
Multiple Sensor ◽  
Protocol Execution ◽  
And Performance ◽  
The Cost

Collection of rare but delay-critical messages from a group of sensor nodes is a key process in many wireless sensor network applications. This is particularly important for security-related applications like intrusion detection and fire alarm systems. An event sensed by multiple sensor nodes in the network can trigger many messages to be sent simultaneously. We present Alert, a MAC protocol for collecting event-triggered urgent messages from a group of sensor nodes with minimum latency and without requiring any cooperation or prescheduling among the senders or between senders and receiver during protocol execution. Alert is designed to handle multiple simultaneous messages from different nodes efficiently and reliably, minimizing the overall delay to collect all messages along with the delay to get the first message. Moreover, the ability of the network to handle a large number of simultaneous messages does not come at the cost of excessive delays when only a few messages need to be handled. We analyze Alert and evaluate its feasibility and performance with an implementation on commodity hardware. We further compare Alert with existing approaches through simulations and show the performance improvement possible through Alert.

Sign in / Sign up

Export Citation Format

Share Document