Preparation of vinyl polymer/polyurethane hybrid latex particles and their application in nano-sized vinyl polymer particle/thermoplastic polyurethane blends

e-Polymers ◽  
2010 ◽  
Vol 10 (1) ◽  
Author(s):  
Yanyan Wei ◽  
Chengzhong Zong ◽  
Fufang Wang
Keyword(s):  
Mechanical Properties ◽  
Thermoplastic Polyurethane ◽  
Polymer Particle ◽  
Gravimetric Analysis ◽  
Hybrid Particles ◽  
Scanning Calorimetry ◽  
Latex Particles ◽  
Vinyl Polymer ◽  
Hybrid Latex ◽  
Polyurethane Matrix

AbstractVinyl polymer/polyurethane hybrid latex particles with various compositions were successfully prepared via emulsion polymerization of vinyl monomer in the presence of self-emulsified polyurethane dispersion without using any surfactant. Studies were carried out on polymerization kinetics, characterization of the hybrid particles and the physical properties of nano-sized vinyl polymer particle/thermoplastic polyurethane blends. It was found that the maximum content of vinyl polymer in polyurethane hybrid particles was up to 80 percent and all of the vinyl polymer/polyurethane hybrid particles were less than 120 nm. Infrared spectroscopy, thermal gravimetric analysis and differential scanning calorimetry analysis indicated the influence of vinyl polymer on the polyurethane hybrid particles. With the polyurethane shells outside and, therefore, good compatibility with polyurethane matrix, the hybrid particles can be easily blended into polyurethane matrix. Some unusual changes of dynamic mechanical properties in the low temperature region were found in the blends of hybrid particles and thermoplastic polyurethane. With the addition of only 3%, the mechanical properties of these blends did not show a significant change. This study provided a new method to prepare hybrid particles in the absence of surfactant and made an attempt on application of vinyl polymer/polyurethane hybrid particles in the blending modification

scholarly journals Biocomposites of Bio-Polyethylene Reinforced with a Hydrothermal-Alkaline Sugarcane Bagasse Pulp and Coupled with a Bio-Based Compatibilizer

Molecules ◽  
2020 ◽  
Vol 25 (9) ◽  
pp. 2158
Author(s):  
Nanci Vanesa Ehman ◽  
Diana Ita-Nagy ◽  
Fernando Esteban Felissia ◽  
María Evangelina Vallejos ◽  
Isabel Quispe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Water Absorption ◽  
Sugarcane Bagasse ◽  
Thermo Gravimetric Analysis ◽  
Decomposition Temperature ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Cradle To Gate ◽  
Bagasse Pulp

Bio-polyethylene (BioPE, derived from sugarcane), sugarcane bagasse pulp, and two compatibilizers (fossil and bio-based), were used to manufacture biocomposite filaments for 3D printing. Biocomposite filaments were manufactured and characterized in detail, including measurement of water absorption, mechanical properties, thermal stability and decomposition temperature (thermo-gravimetric analysis (TGA)). Differential scanning calorimetry (DSC) was performed to measure the glass transition temperature (Tg). Scanning electron microscopy (SEM) was applied to assess the fracture area of the filaments after mechanical testing. Increases of up to 10% in water absorption were measured for the samples with 40 wt% fibers and the fossil compatibilizer. The mechanical properties were improved by increasing the fraction of bagasse fibers from 0% to 20% and 40%. The suitability of the biocomposite filaments was tested for 3D printing, and some shapes were printed as demonstrators. Importantly, in a cradle-to-gate life cycle analysis of the biocomposites, we demonstrated that replacing fossil compatibilizer with a bio-based compatibilizer contributes to a reduction in CO2-eq emissions, and an increase in CO2 capture, achieving a CO2-eq storage of 2.12 kg CO2 eq/kg for the biocomposite containing 40% bagasse fibers and 6% bio-based compatibilizer.

scholarly journals Effects of Nano-CaCO3/Limestone Composite Particles on the Hydration Products and Pore Structure of Cementitious Materials

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Huashan Yang ◽  
Yujun Che
Keyword(s):  
Mechanical Properties ◽  
Pore Structure ◽  
Reaction System ◽  
Cementitious Materials ◽  
Limestone Powder ◽  
Composite Particles ◽  
Gravimetric Analysis ◽  
Hydration Products ◽  
Scanning Calorimetry ◽  
Necked Flask

The agglomeration of nano-CaCO3 (NC) is the largest bottleneck in applications in cementitious materials. If nano-CaCO3 modifies the surface of micron-scale limestone powder (LS), then it will form nano-CaCO3/limestone composite particles (NC/LS). It is known that micron-scale limestone is easily dispersed, and the “dispersion” of NC is governed by that of LS. Therefore, the dispersion of nano-CaCO3 can be improved by the NC/LS in cementitious materials. In this work, the preparation of NC/LS was carried out in a three-necked flask using the Ca(OH)2-H2O-CO2 reaction system. The morphology of NC/LS was observed by a field emission scanning electron microscope (FE-SEM). The effects of NC/LS on the hydration products and pore structure of cementitious materials are proposed. 5% NC/LS was added into cement paste and mortar, and the mechanical properties of the specimens were measured at a certain age. Differential scanning calorimetry (DSC), thermal gravimetric analysis (TG), and backscattered electron imaging (BSE) were conducted on the specimens to investigate the hydration products and pore structure. The properties of specimens with NC/LS were compared to that of control specimens (without NC/LS). The results revealed that NC/LS reduced the porosity and improved the mechanical properties of the cementitious materials.

The influence of adding long basalt fiber on the mechanical and thermal properties of composites based on poly(oxymethylene)

2018 ◽  
Vol 33 (4) ◽  
pp. 435-450 ◽  
Author(s):  
Patrycja Bazan ◽  
Stanisław Kuciel ◽  
Mariola Sądej
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Average Length ◽  
Flexural Modulus ◽  
Basalt Fiber ◽  
Charpy Impact ◽  
Mechanical And Thermal Properties ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Atr Spectroscopy

The work has evaluated the possibility of the potential reinforcing of poly(oxymethylene) (POM) by basalt fibers (BFs) and influence of BFs addition on thermal properties. Two types of composites were produced by injection molding. There were 20 and 40 wt% long BFs content with an average length of 1 mm. The samples were made without using a compatibilizer. In the experimental part, the basic mechanical properties (tensile strength, modulus of elasticity, strain at break, flexural modulus, flexural strength, and deflection at 3.5% strain) of composites based on POM were determined. Tensile properties were also evaluated at three temperatures −20°C, 20°C, and 80°C. The density and Charpy impact of the produced composites were also examined. The influence of water absorption on mechanical properties was investigated. Thermal properties were conducted by the differential scanning calorimetry, thermal gravimetric analysis, and fourier transform infrared (FTIR)-attenuation total reflection (ATR) spectroscopy analysis. In order to make reference to the effects of reinforcement and determine the structure characteristics, scanning electron microscopy images were taken. The addition of 20 and 40 wt% by weight of fibers increases the strength and the stiffness of such composites by more than 30–70% in the range scale of temperature. Manufactured composites show higher thermal and dimensional stability in relation to neat POM.

The effect of hybrid nanoparticle with silica sol as the supporter on the crystallization behavior and mechanical properties of isotactic polypropylene

2015 ◽  
Vol 35 (6) ◽  
pp. 565-573 ◽  
Author(s):  
Juan Li ◽  
Shuhao Qin ◽  
Wentao He ◽  
Yushu Xiang ◽  
Qin Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Isotactic Polypropylene ◽  
Crystallization Behavior ◽  
Optical Microscope ◽  
Silica Sol ◽  
Hybrid Nanoparticles ◽  
Hybrid Particles ◽  
Scanning Calorimetry ◽  
Chemical Action ◽  
Time Dynamic

Abstract Colloidal dispersions of hybrid nanoparticles with silica sol as the supporter (PKSol) were prepared by supporting aromatic phosphate on silica sol via a chemical action with γ-aminopropyltrimethylsilane (KH550) as a linker in wet process for the first time. Dynamic light scattering (DLS) demonstrated that hybrid nanoparticles with an average size of about 200 nm were formed and transmission electron microscopy (TEM) confirmed the presence of the ultrafine silica sols within the hybrid particles, which exhibited “currant-bun” particle morphologies, rather than typical “core-shell” structures for most polymer-encapsulated silica particles. Compared to aromatic phosphate alone and silane-modified silica sol, the effect of PKSol on the crystallization behavior and mechanical properties of isotactic polypropylene (iPP) was investigated using a polarized optical microscope (POM) and differential scanning calorimetry (DSC). The results demonstrated that PKSol showed superior nucleating ability on iPP than the other two. After adding 0.2 wt% PKSol, the crystallization peak temperature of iPP increased from 116.35°C to 120.81°C and the crystallinity increased from 39.6% to 50%. Correspondingly, the haze decreased from 37.6% to 23.3% and mechanical properties were improved.

Study on Degumming Technology and Properties of Pineapple Leaf Fiber

2014 ◽  
Vol 484-485 ◽  
pp. 70-74
Author(s):  
Yu Ling Zhao ◽  
Zhuo Zhang
Keyword(s):  
Mechanical Properties ◽  
Good Condition ◽  
Fiber Surface ◽  
Relative Strength ◽  
Good Effect ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Advantages And Disadvantages ◽  
Pineapple Leaf Fiber ◽  
Leaf Fiber

This paper analyzes several existing pineapple leaf fiber degumming methods and their advantages and disadvantages and describes its relationship with the degumming from the structure characteristics and chemical properties of pineapple leaf fiber. The author puts forward the pineapple leaf fiber degumming technology should be to "high-quality, efficient, low consumption, low pollution" direction of development, and put forward a new method of degumming. By means of scanning electron microscope, infrared spectroscopy, mechanical properties, thermal gravimetric analysis, differential scanning calorimetry and other means, to study the structure, mechanical properties and thermal properties of pineapple leaf fiber biochemical degumming treatment. The results show that: biochemical degumming can take off the original fiber, fiber surface glue residue, single fiber are glial exist, but the fiber separation in good condition, the fiber surface is smooth; hemicellulose degradation in biochemical degumming process, but did not completely removed; no effect on biochemical degumming of pineapple leaf fiber structure has good effect, degumming the treated fiber; degumming relative strength; fiber still has relatively high heat resistance.

Preparation of epoxy/urethane graft interpenetrating polymer networks and study of mechanical, thermal and morphological properties

e-Polymers ◽  
2009 ◽  
Vol 9 (1) ◽  
Author(s):  
Mehdi Ghafghazi ◽  
Masoud Esfandeh ◽  
Jalil Morshedian
Keyword(s):  
Mechanical Properties ◽  
Polymer Networks ◽  
Weight Ratio ◽  
Interpenetrating Polymer Networks ◽  
Morphological Properties ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Molecular Weights ◽  
Degradation Temperature ◽  
Ft Ir

AbstractThis paper describes the preparation of Epoxy/Urethane (EP/PU) graft interpenetrating polymer networks (g-IPNs) and investigates the effect of EP/PU weight ratio and urethane's prepolymer molecular weight on the mechanical, morphological and thermal properties of the IPN system. Here, g-IPN was prepared by thorough mixing of an isocyanate-terminated urethane prepolymer with an epoxy resin followed by simultaneous curing of the resins. Polytetra hydrofuranate (PTHF), molecular weights (Mw) 1000, 2000 and 3000 g/gmol, was used to prepare urethane prepolymers. EP/PU weight ratios were 75/25, 50/50, 30/70 and 15/85. Disappearance of epoxide and isocyanate functional groups was followed by Fourier Transform Infrared spectroscopy (FT-IR), showing curing of the resins. Differential Scanning Calorimetry (DSC) was used to investigate the glass transition temperature (Tg) of the IPNs. Thermal Gravimetric Analysis (TGA), Dynamic Mechanical Thermal Analysis (DMTA), tensile measurements and Scanning Electron Microscopy (SEM) were used to study thermal, mechanical and morphological properties of the prepared systems. The best mechanical properties were obtained at EP/PU weight ratio 75/25 which also shows a fine and uniformly dispersed morphology. Moreover, at this ratio, with increasing PTHF Mw in the urethane prepolymer, the mechanical properties were improved whereas a decrease was observed in Tg and thermal degradation temperature of g-IPNs.

Pad Degradation During CMP Process: Effect of Soak in Slurry and Water on Thermal and Mechanical Properties of the CMP Pads

2003 ◽  
Vol 767 ◽  
Author(s):  
A. Tregub ◽  
G. Ng ◽  
M. Moinpour
Keyword(s):  
Mechanical Properties ◽  
Differential Scanning Calorimetry ◽  
Thermal Gravimetric Analysis ◽  
Mechanical Analysis ◽  
Gravimetric Analysis ◽  
Thermal And Mechanical Properties ◽  
Thermal Gravimetric ◽  
Scanning Calorimetry ◽  
Modulated Differential Scanning Calorimetry ◽  
Thermal Mechanical Analysis

AbstractSoak of polyurethane-based CMP pads in tungsten slurry and de-ionized water and its effect on retention of thermal and mechanical properties of the pads was studied using Dynamic Mechanical Analysis (DMA), Thermal Mechanical Analysis (TMA), Thermal Gravimetric Analysis (TGA), and Modulated Differential Scanning Calorimetry (MDSC). Simultaneous cross-linking and plastisizing due to soak were established using DMA and MDSC analysis. The stable operating temperature range and its dependence on soak time were determined using TMA analysis. Substantial difference in diffusion behavior of the “soft” and “hard” pads was discovered: diffusion into the hard pads followed Fickian law [1], while diffusion into the multi-layer soft pads was dominated by the fast filling of the highly porous pad surface with liquid.During a traditional CMP process, which involves application of polishing pads and slurry, the pad properties can be substantially and irreversibly changed as the result of slurry/rinse water absorption.The retention of the pad properties after exposure was monitored using such thermal and mechanical techniques, as Thermal Mechanical Analysis (TMA), Dynamical Mechanical Analysis (DMA), Modulated Differential Scanning Calorimetry (MDSC), Thermal Gravimetric Analysis (TGA).

Experimental Investigation of Kevlar KM2Plus Nano-Reinforced Laminated Composite Thermo-Mechanical Properties

2016 ◽  
Author(s):  
Abdel-Hamid I. Mourad ◽  
Omar G. Ayad ◽  
Ashfakur Rahman ◽  
Ali Hilal-Alnaqbi ◽  
Basim I. Abu-Jdayil
Keyword(s):  
Mechanical Properties ◽  
Thermo Gravimetric Analysis ◽  
Laminated Composite ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Thermo Gravimetric ◽  
Three Point Bending ◽  
Multi Walled Carbon Nanotube ◽  
Thermal Stability Of

This work is concerned with the synthesis and characterization of Multi-Walled Carbon Nanotube (MWCNT) reinforced Kevlar KM2Plus composites with various MWCNT contents (0.2, 0.3, 0.4, 0.5, 0.6, and 0.8 wt. %), by the wet lay-up technique. These samples were experimentally investigated for their thermo-mechanical properties using Thermo-Gravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), tensile testing and three-point bending techniques. The mechanical properties showed remarkable improvement with increasing MWCNT wt.% up to certain content. The results revealed that the addition of MWCNT fillers has no significant effect on the thermal stability of the composites.

Effect of Ultrasound and Strain Rate on Tensile Behavior of Neat Thermoplastic Polyurethane Thin Films

2010 ◽  
Author(s):  
Anandh Balakrishnan ◽  
Mrinal C. Saha
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Strain Rate ◽  
Mechanical Test ◽  
Thermoplastic Polyurethane ◽  
Optical Element ◽  
Mechanical Tests ◽  
Primary Objective ◽  
Scanning Calorimetry ◽  
Rate Dependent

Thermoplastic Polyurethane (TPU) thin films have many applications in engineering and biomedical fields. Examples include moisture sensors, load cells, optical element and biocompatible stens. The TPU is a block copolymer naturally phase segregates into thermodynamically incompatible hard- and soft-segments. The size of the segments and their spatial distribution can significantly affect the microstructure and mechanical properties of the TPU. In this paper, we propose to investigate the effect of ultrasound energy on mechanical properties of TPU thin films fabricated via a solution route utilizing Tetra Hydro Furan (THF) as a solvent. The times of sonication was fixed at 60 minutes whilst all films were fabricated at average thickness of 20+/-5 um. The primary objective of the study was to understand the influence of ultrasound and strain rates on the material microstructure and the resulting mechanical properties. Mechanical tests have been conducted at two different displacement rates, namely 5 and 10 mm/min. Our preliminary results indicate that ultrasound improves the strength of the neat TPU films. We also see that strain hardening is displacement or strain rate dependent. We attribute these results to changes in the hard (H) and soft (S) domain structure. To further understand these microstructural variations, we propose to conduct Differential Scanning Calorimetry (DSC). The data has been interpreted in conjunction with our mechanical test data.

Sign in / Sign up

Export Citation Format

Share Document