Production of aluminum nanoparticles by wet mechanical milling

MRS Advances ◽  
2020 ◽  
Vol 5 (61) ◽  
pp. 3133-3140
Author(s):  
S. Mancillas-Salas ◽  
P. Hernández-Rodríguez ◽  
A.C. Reynosa-Martínez ◽  
E. López-Honorato
Keyword(s):  
Mechanical Milling ◽  
Arc Discharge ◽  
Aluminum Nanoparticles ◽  
Attrition Milling ◽  
Transmission Electron ◽  
Low Costs ◽  
Agglomeration Of Nanoparticles ◽  
High Yields ◽  
20 Nm ◽  
By Products

AbstractOne of the great challenges in the use of nanomaterials is their production at low costs and high yields. In this work aluminum nanoparticles, from aluminum powder, were produced by wet mechanical milling through a combination of different attrition milling conditions such as ball-powder ratio (BPR) and the amount of solvent used. It was observed that at 600 rpm with a BPR of 500/30 g for 12 h, it was possible to produce nanoparticles with a size close to 20 nm, while at 750 rpm with a BPR of 380/12.6 g for 12 h, nanoparticles of approximately 10 nm were obtained. Scanning and transmission electron microscopy confirmed that the milling product is an agglomeration of nanoparticles with different sizes. These results show the feasibility of obtaining aluminum nanoparticles by mechanical milling using only ethanol as solvent, avoiding hazardous by-products obtained from chemical routes, and the use of complicated methods such as laser ablation and arc discharge.

Precipitation of carbon nanoparticles encapsulating silicon carbide from molten oxide

1998 ◽  
Vol 13 (8) ◽  
pp. 2039-2041
Author(s):  
Mamoru Mitomo ◽  
Chong-Min Wang ◽  
Hideyuki Emoto
Keyword(s):  
Carbon Nanoparticles ◽  
Preparation Method ◽  
Arc Discharge ◽  
Electric Arc ◽  
Carbon Nanoparticle ◽  
Oxide Melt ◽  
Transmission Electron ◽  
Ceramic Process ◽  
Molten Oxide ◽  
20 Nm

A kind of fullerenes, carbon nanoparticle encapsulating β–SiC grain, was precipitated during cooling Al2O3–Y2O3 –CaO oxide melt containing SiC and C from 2023 K. The SiC grains with a diameter of 5–20 nm were covered with 2–4 graphitic carbon layers with the spacing of 0.34 nm as revealed by high resolution transmission electron microscopy. The result provides a new preparation method of carbon nanoparticles through a ceramic process, which contrasts with previous physical methods applying electric arc discharge or electron irradiation in vacuum.

Low Energy Ar Ion Milling of FIB TEM Specimens from 14 nm and Future FinFET Technologies

2018 ◽  
Author(s):  
C.S. Bonifacio ◽  
P. Nowakowski ◽  
M.J. Campin ◽  
M.L. Ray ◽  
P.E. Fischione
Keyword(s):  
Field Effect Transistor ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Ion Milling ◽  
Transmission Electron ◽  
High Resolution Tem ◽  
Effect Transistor ◽  
20 Nm ◽  
Argon Ion

Abstract Transmission electron microscopy (TEM) specimens are typically prepared using the focused ion beam (FIB) due to its site specificity, and fast and accurate thinning capabilities. However, TEM and high-resolution TEM (HRTEM) analysis may be limited due to the resulting FIB-induced artifacts. This work identifies FIB artifacts and presents the use of argon ion milling for the removal of FIB-induced damage for reproducible TEM specimen preparation of current and future fin field effect transistor (FinFET) technologies. Subsequently, high-quality and electron-transparent TEM specimens of less than 20 nm are obtained.

Utilizing Nanoprobing and Circuit Diagnostics to Identify Key Failure Mechanism of Otherwise Nonvisible Defects in 20 nm Logic Devices

2014 ◽  
Author(s):  
M.K. Dawood ◽  
C. Chen ◽  
P.K. Tan ◽  
S. James ◽  
P.S. Limin ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Contact Layer ◽  
Fault Isolation ◽  
Tem Analysis ◽  
Logic Devices ◽  
Technology Advancement ◽  
Transmission Electron ◽  
Voltage Contrast ◽  
Almost All ◽  
20 Nm

Abstract In this work, we present two case studies on the utilization of advanced nanoprobing on 20nm logic devices at contact layer to identify the root cause of scan logic failures. In both cases, conventional failure analysis followed by inspection of passive voltage contrast (PVC) failed to identify any abnormality in the devices. Technology advancement makes identifying failure mechanisms increasingly more challenging using conventional methods of physical failure analysis (PFA). Almost all PFA cases for 20nm technology node devices and beyond require Transmission Electron Microscopy (TEM) analysis. Before TEM analysis can be performed, fault isolation is required to correctly determine the precise failing location. Isolated transistor probing was performed on the suspected logic NMOS and PMOS transistors to identify the failing transistors for TEM analysis. In this paper, nanoprobing was used to isolate the failing transistor of a logic cell. Nanoprobing revealed anomalies between the drain and bulk junction which was found to be due to contact gouging of different severities.

scholarly journals (Ti,Al)O2 Whiskers Grown during Glow Discharge Nitriding of Ti-6Al-7Nb Alloy

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2658
Author(s):  
Krzysztof Szymkiewicz ◽  
Jerzy Morgiel ◽  
Łukasz Maj ◽  
Małgorzata Pomorska
Keyword(s):  
Surface Hardening ◽  
Surface Defects ◽  
Plasma Nitriding ◽  
Surface Roughening ◽  
Effective Surface ◽  
Plan View ◽  
Gas Nitriding ◽  
Transmission Electron ◽  
Temperature Window ◽  
20 Nm

Plasma nitriding of titanium alloys is capable of effective surface hardening at temperatures significantly lower than gas nitriding, but at a cost of much stronger surface roughening. Especially interesting are treatments performed at the lower end of the temperature window used in such cases, as they are least damaging to highly polished parts. Therefore identifying the most characteristic defects is of high importance. The present work was aimed at identifying the nature of pin-point bumps formed at the glow discharged plasma nitrided Ti-6Al-7Nb alloy using plan-view scanning and cross-section transmission electron microscopy methods. It helped to establish that these main surface defects developed at the treated surface are (Ti,Al)O2 nano-whiskers of diameter from 20 nm to 40 nm, and length up to several hundreds of nanometers. The performed investigation confirmed that the surface imperfection introduced by plasma nitriding at the specified range should be of minor consequences to the mechanical properties of the treated material.

Low-temperature route to nanoscale P3N5 hollow spheres

2003 ◽  
Vol 18 (10) ◽  
pp. 2359-2363 ◽  
Author(s):  
Hongzhou Gu ◽  
Yunle Gu ◽  
Zhefeng Li ◽  
Yongcheng Ying ◽  
Yitai Qian
Keyword(s):  
Photoelectron Spectroscopy ◽  
Hollow Spheres ◽  
Molar Ratio ◽  
Visible Absorption ◽  
X Ray ◽  
Transmission Electron ◽  
Influence Of Temperature On ◽  
Wide Gap ◽  
20 Nm ◽  
High Degree

Nanoscale hollow spheres of amorphous phosphorus nitride (P3N5) were synthesized by reacting PCl3 with NaN3 at 150–250 °C. Transmission electron microscope images show that the hollow spheres have a diameter of 150–350 nm, and the thickness of the shell is 20 nm. A very small amount of curly films were also found in the sample prepared at 150 °C. The infrared spectrum indicates a high degree of purity. X-ray photoelectron spectroscopy indicates the presence of P and N, with a molar ratio of 1:1.62 for P:N. Ultraviolet-visible absorption spectroscopy shows an absorption band at 265–315 nm. Under photoluminescent excitation at 230 nm, the P3N5 emits ultraviolet light at 305 nm. With a band gap of 4.28 eV, the products may be a wide gap semiconductor. A possible mechanism and the influence of temperature on the formation of the hollow spheres are also discussed.

Computer simulations of interactions between ultrafine alumina particles produced by an arc discharge

1997 ◽  
Vol 12 (1) ◽  
pp. 235-243 ◽  
Author(s):  
M. H. Teng ◽  
L. D. Marks ◽  
D. L. Johnson
Keyword(s):  
Electron Microscope ◽  
Surface Energy ◽  
Transmission Electron Microscope ◽  
Arc Discharge ◽  
Total Surface Energy ◽  
Transmission Electron ◽  
Initial Stage ◽  
Alumina Particles ◽  
Rearrangement Process ◽  
Particle Chains

We wrote two computer programs, 3D and BUMP, to interpret transmission electron microscope (TEM) micrographs made during a study of the initial stage sintering of ultrafine alumina particles (UFP's, 20–50 nm in diameter). The first simulated the 3D geometric relationships of particles, from which we concluded that surface diffusion was the predominant sintering mechanism because no shrinkage occurred. BUMP simulated random contact of two particles and showed that the particle chains that formed before sintering were not formed purely by chance. Instead the particles experienced a rearrangement process (rotation and sliding) which reduced the total surface energy.

Design and use of an Efficient Plasma Jet Reactor for High Temperature Gas/Solid Reactions

1983 ◽  
Vol 30 ◽  
Author(s):  
F. W. Giacobbe ◽  
D. W. Schmerling
Keyword(s):  
Carbon Monoxide ◽  
High Temperature ◽  
Arc Discharge ◽  
Plasma Jet ◽  
Direct Result ◽  
Discharge Region ◽  
Plasma Flame ◽  
Powdered Carbon ◽  
High Yields ◽  
Experimental Trials

ABSTRACTA unique and efficient plasma jet reactor has been developed and used to study the high temperature production of carbon monoxide from a reaction between powdered carbon and a pure carbon dioxide plasma. The plasma jet reactor was designed to allow the injection of powdered carbon above the arc discharge region rather than into the plasma flame below the arc discharge region. High yields of carbon monoxide, produced at relatively high efficiencies, were a direct result of this technique. The plasma jet was also designed to enable rapid changing and testing of various anode insertsAverage yields of carbon monoxide in the product gases were as high as 80–87% in selected experimental trials. Carbon monoxide was produced at rates exceeding 15,000 1/hr (at STP) with a power expenditure of 52 Kw.

Tribological Behavior of Carbon Nanotubes as an Additive on Lithium Grease

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
Alaa Mohamed ◽  
T. A. Osman ◽  
A. Khattab ◽  
M. Zaki
Keyword(s):  
Carbon Nanotubes ◽  
Arc Discharge ◽  
Average Diameter ◽  
Friction Reduction ◽  
Lithium Grease ◽  
X Ray ◽  
Transmission Electron ◽  
Boundary Film ◽  
Load Carrying ◽  
Worn Surface

Carbon nanotubes (CNTs) with 10 nm average diameter and 5 μm in length were synthesized by electric arc discharge. The morphology and structure of CNTs were characterized by high resolution transmission electron microscopy (HRTEM) and X-ray powder diffraction. The tribological properties of CNTs as an additive on lithium grease were evaluated with a four ball tester. The results show that the grease with CNTs exhibit good performance in antiwear (AW) and decrease the wear scare diameter (WSD) about 63%, decrease friction reduction about 81.5%, and increase the extreme pressure (EP) properties and load carrying capacity about 52% with only 1% wt. of CNTs added to lithium grease. The action mechanism was estimated through analysis of the worn surface with a scanning electron microscope (SEM) and energy dispersive X-ray (EDX). The results indicate that a boundary film mainly composed of CNTs, Cr, iron oxide, and other organic compounds was formed on the worn surface during the friction process.

Study of the Effect of Anode/Cathode Geometry on the Yield Rate and Quality of the MWCNTs Synthesized by Submerged Arc Discharging

2013 ◽  
Author(s):  
Osama M. Awadallah ◽  
Ragaie M. Rashad ◽  
Abdalla S. Wifi
Keyword(s):  
Arc Discharge ◽  
Multiwalled Carbon ◽  
Yield Rate ◽  
Transmission Electron ◽  
Water As Solvent ◽  
Quantitative Manner ◽  
A356 Aluminum ◽  
Submerged Arc ◽  
Selection Of

The main objective of the present paper is to clarify the effect of anode/cathode geometry combinations on the yield rate and quality of the Multiwalled Carbon Nanotubes (MWCNTs) produced by submerged arc discharge technique. The effects of current intensity and the discharging medium (solvent) are also investigated. The morphology and crystalline perfection of the produced MWCNTs are confirmed by transmission electron microscopy (TEM) and Electron diffraction. Thermogravimetric analysis (TGA) is conducted to check the quality of the MWCNTs in a quantitative manner. The flat ended anode/cathode combination of diameters 4 and 12 mm respectively exhibited the highest yield at 70 A using deionized water as solvent. Through careful selection of the process parameters, the yield rate of MWCNTs obtained is found to be higher than most of the reported values in literature. However, the best quality of MWCNTs with purity as high as 95%, average thermal stability of 745°C as well as good batch homogeneity, is obtained with KCl solution and tapered male/female anode combination. The best quality MWCNTs is used successfully as reinforcement for A356 aluminum silicon composite.

A Facile Fynthesis of ZnS Nanostructures via Liquid-Solid Reactions

2014 ◽  
Vol 979 ◽  
pp. 184-187
Author(s):  
Weerachon Phoohinkong ◽  
Thitinat Sukonket ◽  
Udomsak Kitthawee
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Inorganic Salts ◽  
Chloride Salt ◽  
X Ray ◽  
Commercial Grade ◽  
Transmission Electron ◽  
Salt Addition ◽  
20 Nm ◽  
Scanning Electron

Zinc sulfide (ZnS) nanostructures are important materials for many technologies such as sensors, infrared windows, transistors, LED displays, and solar cells. However, many methods of synthesizing ZnS nanostructures are complex and require expensive equipment. In this study, a liquid-solid chemical reaction without surfactant was used to synthesize ZnS at room temperature. In addition, commercial grade zinc oxide (ZnO) particles were used as a precursor. The effect of the addition of acids and inorganic salts were investigated. The products were characterized by field emission scanning electron microscopy (FESEM) coupled with energy-dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM). The results show that the nanoparticles of ZnS were obtained in hydrochloric acid and acetic acid addition. The diameters were in the range of 10 to 20 nm and 50 to 100 nm, respectively. In the case of a sodium chloride salt addition, a ZnS structure was obtained with a particle size of approximately 5 nm and a flake-like morphology.

Sign in / Sign up

Export Citation Format

Share Document