Mechanical Behavior of Rigid Rod Polymeric Fibers

1988 ◽  
Vol 134 ◽  
Author(s):  
Steven R. Allen ◽  
Richard J. Farris
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Tensile Modulus ◽  
Structure Property ◽  
Polymeric Fibers ◽  
Shear Moduli ◽  
Structure Property Relationships ◽  
Secondary Interactions ◽  
Rigid Rod

ABSTRACTPoly-(p-phenylene benzobisthiazole) fibers provide a model system for the evaluation of structure-property relationships in extended-chain polymeric fibers. Owing to the poorly developed lateral order in as-spun fibers, the enhancement of structural perfection and of mechanical properties may be examined through heat treatment processing more readily than with more crystalline fibers. High tensile modulus (to 300 GPa) and high tensile strength (3 GPa) have been obtained from heat treatment processing of the fibers. The development of tensile modulus and tensile strength depends directly on the enhancement of overall axial molecular orientation. Tensile strength is additionally dominated by the development of stronger lateral molecular interaction. The mechanical properties mimic the inherent chain anisotropy arising from strong primary bonding along the chain and much weaker secondary interactions between chains. Tensile to shear moduli ratios of 200:1, tensile to shear strength ratios of 50:1 and tensile to compressive strength ratios of 10:1 are observed.

Properties of a Photoimageable Thin Polyimide Film

1990 ◽  
Vol 203 ◽  
Author(s):  
Taishih Maw ◽  
Richard E. Hopla
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Tensile Modulus ◽  
Polyimide Film ◽  
Decomposition Temperature ◽  
Irganox 1010 ◽  
Elongation At Break ◽  
Purge Gas ◽  
Exposure Energy

ABSTRACTMechanical properties (tensile modulus, tensile strength, elongation at break), thermal properties (T8' CTE, thermo-decomposition temperature, and rate of weight loss) and electrical properties of Problmlde 414 cured films have been determined. The mechanical properties of Probimide 414 thin films are highly dependent on the hard-bake temperature, hard-bake time, and purge gas, but not dependent on the level of the exposure energy or the presence of 1% Irganox 1010 (w/w) as a stabilizer. At a hard-bake temperature of 350ºC and a nitrogen purge rate of 15 SCFH, Probimide 414 films showed excellent retention of the mechanical properties during extended heat treatment.

Vulcanization of Butyl Rubber: Curative Effects of 2-Pentadecylbenzoquinonedioxime

1981 ◽  
Vol 54 (4) ◽  
pp. 692-697 ◽  
Author(s):  
N. D. Ghatge ◽  
N. N. Maldar
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Butyl Rubber ◽  
Structure Property ◽  
Structure Property Relationships ◽  
Rubber Vulcanizate ◽  
Aging Study ◽  
Red Lead ◽  
Good Retention

Abstract The structure-property relationships of butyl rubber vulcanizates derived from quinonedioxime-red lead or quinonedioxime-MBTS-sulfur cure systems were studied. The effects of the dioxime curatives on the mechanical properties of the elastomer are discussed on the basis of rheological and heat-aging study. It was found that a 2-pentadecylbenzoquinonedioxime-MBTS-sulfur cured butyl rubber vulcanizate shows good retention of tensile strength on heat aging at 125°C.

Morphology of High-Performance Rigid-Rod Polymer Fibers and Molecular Composites

1989 ◽  
Vol 47 ◽  
pp. 338-339
Author(s):  
W.W. Adams ◽  
S. J. Krause
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Liquid Crystalline ◽  
Molecular Level ◽  
Synergistic Effects ◽  
Tensile Modulus ◽  
Commercial Development ◽  
The Matrix ◽  
Molecular Composites ◽  
Rigid Rod

Rigid-rod polymers such as PBO, poly(paraphenylene benzobisoxazole), Figure 1a, are now in commercial development for use as high-performance fibers and for reinforcement at the molecular level in molecular composites. Spinning of liquid crystalline polyphosphoric acid solutions of PBO, followed by washing, drying, and tension heat treatment produces fibers which have the following properties: density of 1.59 g/cm3; tensile strength of 820 kpsi; tensile modulus of 52 Mpsi; compressive strength of 50 kpsi; they are electrically insulating; they do not absorb moisture; and they are insensitive to radiation, including ultraviolet. Since the chain modulus of PBO is estimated to be 730 GPa, the high stiffness also affords the opportunity to reinforce a flexible coil polymer at the molecular level, in analogy to a chopped fiber reinforced composite. The objectives of the molecular composite concept are to eliminate the thermal expansion coefficient mismatch between the fiber and the matrix, as occurs in conventional composites, to eliminate the interface between the fiber and the matrix, and, hopefully, to obtain synergistic effects from the exceptional stiffness of the rigid-rod molecule. These expectations have been confirmed in the case of blending rigid-rod PBZT, poly(paraphenylene benzobisthiazole), Figure 1b, with stiff-chain ABPBI, poly 2,5(6) benzimidazole, Fig. 1c A film with 30% PBZT/70% ABPBI had tensile strength 190 kpsi and tensile modulus of 13 Mpsi when solution spun from a 3% methane sulfonic acid solution into a film. The modulus, as predicted by rule of mixtures, for a film with this composition and with planar isotropic orientation, should be 16 Mpsi. The experimental value is 80% of the theoretical value indicating that the concept of a molecular composite is valid.

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

scholarly journals Heat Treatment Evaluation for the Camshafts Production of ADI Low Alloyed with Vanadium

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1036
Author(s):  
Eduardo Colin García ◽  
Alejandro Cruz Ramírez ◽  
Guillermo Reyes Castellanos ◽  
José Federico Chávez Alcalá ◽  
Jaime Téllez Ramírez ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ductile Iron ◽  
Volume Fraction ◽  
Energy Impact ◽  
Treatment Conditions ◽  
Mold Casting ◽  
Grade 3 ◽  
Good Agreement

Ductile iron camshafts low alloyed with 0.2 and 0.3 wt % vanadium were produced by one of the largest manufacturers of the ductile iron camshafts in México “ARBOMEX S.A de C.V” by a phenolic urethane no-bake sand mold casting method. During functioning, camshafts are subject to bending and torsional stresses, and the lobe surfaces are highly loaded. Thus, high toughness and wear resistance are essential for this component. In this work, two austempering ductile iron heat treatments were evaluated to increase the mechanical properties of tensile strength, hardness, and toughness of the ductile iron camshaft low alloyed with vanadium. The austempering process was held at 265 and 305 °C and austempering times of 30, 60, 90, and 120 min. The volume fraction of high-carbon austenite was determined for the heat treatment conditions by XRD measurements. The ausferritic matrix was determined in 90 min for both austempering temperatures, having a good agreement with the microstructural and hardness evolution as the austempering time increased. The mechanical properties of tensile strength, hardness, and toughness were evaluated from samples obtained from the camshaft and the standard Keel block. The highest mechanical properties were obtained for the austempering heat treatment of 265 °C for 90 min for the ADI containing 0.3 wt % V. The tensile and yield strength were 1200 and 1051 MPa, respectively, while the hardness and the energy impact values were of 47 HRC and 26 J; these values are in the range expected for an ADI grade 3.

Mechanical properties of low-density paper

2020 ◽  
Vol 35 (1) ◽  
pp. 61-70
Author(s):  
Na Young Park ◽  
Young Chan Ko ◽  
Lili Melani ◽  
Hyoung Jin Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Structural Change ◽  
Tensile Testing ◽  
Tensile Modulus ◽  
Gauge Length ◽  
Efficiency Factor ◽  
Low Density ◽  
Tensile Stiffness ◽  
Lower Tensile Strength

AbstractFor the mechanical properties of paper, tensile testing has been widely used. Among the tensile properties, the tensile stiffness has been used to determine the softness of low-density paper. The lower tensile stiffness, the greater softness of paper. Because the elastic region may not be clearly defined in a load-elongation curve, it is suggested to use the tensile modulus which is defined as the slope between the two points in the curve. The two points which provide the best correlation with subjective softness evaluation should be selected. Low-density paper has a much lower tensile strength, but much larger elongation at the break. It undergoes a continuous structural change during mechanical testing. The degree of the structural change should depend on tensile conditions such as the sample size, the gauge length, and the rate of elongation. For low-density paper, the tensile modulus and the tensile strength should be independent of each other. The structure efficiency factor (SEF) is defined as a ratio of the tensile strength to the tensile modulus and it may be used a guideline in developing superior low-density paper products.

scholarly journals Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 647 ◽  
Author(s):  
Bingrong Zhang ◽  
Lingkun Zhang ◽  
Zhiming Wang ◽  
Anjiang Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Intermediate Phase ◽  
High Strength ◽  
Mg Alloys ◽  
Artificial Ageing ◽  
Treatment Conditions ◽  
Eutectic Si

In order to obtain high-strength and high-ductility Al–Si–Cu–Mg alloys, the present research is focused on optimizing the composition of soluble phases, the structure and morphology of insoluble phases, and artificial ageing processes. The results show that the best matches, 0.4 wt% Mg and 1.2 wt% Cu in the Al–9Si alloy, avoided the toxic effect of the blocky Al2Cu on the mechanical properties of the alloy. The addition of 0.6 wt% Zn modified the morphology of eutectic Si from coarse particles to fine fibrous particles and the texture of Fe-rich phases from acicular β-Fe to blocky π-Fe in the Al–9Si–1.2Cu–0.4Mg-based alloy. With the optimization of the heat treatment parameters, the spherical eutectic Si and the fully fused β-Fe dramatically improved the ultimate tensile strength and elongation to fracture. Compared with the Al–9Si–1.2Cu–0.4Mg-based alloy, the 0.6 wt% Zn modified alloy not only increased the ultimate tensile strength and elongation to fracture of peak ageing but also reduced the time of peak ageing. The following improved combination of higher tensile strength and higher elongation was achieved for 0.6 wt% Zn modified alloy by double-stage ageing: 100 °C × 3 h + 180 °C × 7 h, with mechanical properties of ultimate tensile strength (UTS) of ~371 MPa, yield strength (YS) of ~291 MPa, and elongation to fracture (E%) of ~5.6%.

Morphology of Rigid-Rod Molecular Composites: An Overview

1988 ◽  
Vol 134 ◽  
Author(s):  
Stephen J. Krause
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Morphological Characterization ◽  
High Ratio ◽  
Structure Property ◽  
Chain Polymer ◽  
Specific Strength ◽  
Composite Systems ◽  
Molecular Composites ◽  
Rigid Rod

ABSTRACTRigid-rod molecular composites are a new class of high performance structural polymers which have high specific strength and modulus and also high thermal and environmental resistance. A rigid-rod, extended chain polymer component is used to reinforce a matrix of a ductile polymer with the intent of achieving a “composite” on the molecular level. After synthesis, the key to producing a molecular composite is to control morphology to disperse the reinforcing rod molecules as finely as possible in the matrix polymer. Individual rod molecules or bundles of molecular rods must have dimensions which result in a high ratio of length to width (aspect ratio) for efficient reinforcement. To achieve this, the reinforcing rod component must not phase separate at any stage of processing. Morphological characterization techniques, which can measure the orientation and dispersion (or, conversely, the degree of phase separation) of rod molecules provide the tools for correlating theoretically predicted and experimentally observed mechanical properties. Various morphological techniques which have been applied to molecular composite systems will be reviewed, including wide angle x-ray scattering and scanning and transmission electron microscopy. Structure-property correlations for molecular composite systems will be discussed with regard to models for mechanical properties. Application of new morphological techniques will also be discussed.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

scholarly journals Mechanical Properties of Oil Palm Shell Composites

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
J. Sahari ◽  
M. A. Maleque
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Oil Palm ◽  
Volume Fraction ◽  
Unsaturated Polyester ◽  
Tensile Modulus ◽  
Sem Analysis ◽  
Palm Shell ◽  
Pull Out ◽  
Oil Palm Shell

The mechanical properties of oil palm shell (OPS) composites were investigated with different volume fraction of OPS such as 0%, 10%, 20%, and 30% using unsaturated polyester (UPE) as a matrix. The results presented that the tensile strength and tensile modulus of the UPE/OPS composites increased as the OPS loading increased. The highest tensile modulus of UPE/OPS was obtained at 30 vol% of OPS with the value of 8.50 GPa. The tensile strength of the composites was 1.15, 1.17, and 1.18 times higher than the pure UPE matrix for 10, 20, and 30 vol% of OPS, respectively. The FTIR spectra showed the change of functional group of composites with different volume fractions of OPS. SEM analysis shows the filler pull-out present in the composites which proved the poor filler-matrix interfacial bonding.

Sign in / Sign up

Export Citation Format

Share Document